Search Documents

By H. H. Schrenk, W. P. Yant, P. H. Mautz

"In a study of the chemistry and pathology of chronic benzene poisoning, which was conducted cooperatively by the United. States Bureau of Mines, the Barrett Co., and the producers of benzene, it was necessary to make quantitative determinatious of the abzorption, distribution, and: fate of benzene in the organism. Although methods for determining benzene in relatively large amounts were available no satisfactory method was found for removing and determining the small amounts that are present in the tissues or excretions after exposure to conditions which ultimately cause chronic poisoning. This no doubt accounts for the lack of information in the literature on this particular phase of benzene poisoning.The writers have found in work that will be described in a subsequent publication that the amounts of benzene present in the tissues and excretions under conditions of exposure which produce chronic benzene poisoning arc of the order of a fraction to a few milligrams per 100 grams of tissue. This report describes a method developed and found satisfactory for these determina¬tions.RÉSUMÉ OF PERVIOUS METHODSA method for the determination of benzene in tissue was developed by Joachimoglu. 5 In the Joachimoglu procedure the ground organs are mixed with water and acidified with diluted sulphuzic acid, and the benzene is distilled into a receiver containing carbon tetrachloride. The benzene is nitrated in the carbon tetrachloride, the carbon tetrachloride evaporated, the acid mix¬ture neutralized, and the dinitrobenzene extracted with ether. After removal of the ether the dinitrobeuzene is determined gravimetrically. Joachimoglu reports that this method is about 55 to 60 percent quantitative."

Aug 1, 1935

By James Paone

The Bureau of Mines studied the behavior of rocks at the initial state of crater formation that results from the stresses created under a drill bit to determine which mechanical properties of rock are important in rock fragmentation by drilling. Although a definite relation between the drilling strength and relevant mechanical properties has not been established, maximum yield strength of rock is apparently a parameter of drillability of rock. The strengths of rock were considered from the Mohr-Coulomb criterion from which the surface of failure was constructed. The results from previous tri-axial tests on Solenhofen limestone were adopted to verify the criterion of failure. Inelastic behavior of some rock types was observed under a low-velocity impact of a hemispherical bit and under static indentation with a similar bit. Quantitative determinations of strengths of Solenhofen limestone) Indiana limestone, and Tennessee marble were made under static indentation. The maximum yield strength estimated from the average stress over the indented area was used as the crushing strength of rock under a drill bit.

Jan 1, 1966

By Benjamin W. Haynes

The Bureau of Mines, in cooperation with the National Oceanic and Atmospheric Administration (NOAA), has updated a 1977 NOAA report prepared by Dames & Moore entitled, "Description of Manganese Nodule Processing Activities for Environmental Studies." This updated report contains detailed flowsheets and descriptions of the five potential first-generation nodule recovery schemes now considered most likely to be used by industry; they are high-temperature gas reduction and ammoniacal leach, Cuprion ammoniacal leach, high-temperature and high-pressure H2S04 leach, reduction and HCI leach, and smelting and H2S04 leach. The first three processes are three-metal recovery schemes (Cu, Ni, and Co) with the option of Mn recovery from the tailings. The remaining two processes are four-metal (Cu, Ni, Co, and Mn) recovery schemes. All except the HCI process are assumed to use a nodule feed rate of 3 million tons per year (dry basis). Final metal products are Co powder and cathode Cu and Ni. A minor amount of Ni is also recovered as powder, and some Cu and Zn are recovered as mixed sulfides. Manganese in the four-metal processes is recovered as either manganese metal or ferromanganese.

Jan 1, 1983

By W. H. Oppelt

The continuous gasification of lignite in an externally heated alloy-steel re-tort was investigated by the Bureau of Mines, Grand Forks, N. Dak., from 1945 to 1951. The main objective of the long-term experimental program was to obtain data on the mechanical performance of this type of gasification retort, particularly the alloy-steel heat-transfer surface of the retort, when operated on large pilot-plant scale. At the same time, extensive experimental data were obtained concerning the effect of process variables and the effect of a limited number of design modifications on gasifier performance. In the period covered by this progress report 4 pilot-plant runs totaling 2,879 hours of operation were completed with the rolled-plate, 310-alloy reaction tube. Over 30 million cubic feet of gas, having H2-CO ratios from 2.1 to 4.4, was made by the partial gasification of 636 tons of 1-1/2-by 3/8-inch natural lignite. Rates of gas generation were from 8,200 to 14,300 cubic feet per hour. Three of the four runs were carried out with the lowered gas offtake or continuous-annulus design modification of the gasification retort. In the final run of the series, gasification of lignite from seven different mines in North Dakota and Saskatchewan, Canada, was investigated at similar combustion-space temperatures and lignite and steam feed rates.

Jan 1, 1955

By Cleo Griffith Rall

The method for determining the effective porosity, of oil- and gas- bearing sand described in this report is a development of an earlier method devised by Bureau of Mines. The apparatus has been improved and made more convenient to use, but the procedure has been in use for many years without essential changes. A tabulation at the end of the report gives the results of more than 2,000 porosity determinations for oil sands in the fields of 13 states. A selected bibliography of articles containing descriptions and evaluations of various methods of determining porosity Is a. part of this report. The method was devised and developed at the Petroleum Experiment Station at Bartlesville, Okla., as part of the Bureau's research on fluid-energy relationships and ,on methods of improving the recovery of crude oil from underground reservoirs.

Jan 1, 1949

By Jack Mantel

The goal of this 42-month contract was to increase safety in low-seam underground coal mines through development and in-mine evaluation of a temporary roof support system for roof drills and floor-riding operator compartments for a loader and shuttle car. The program was performed in three phases. During Phase I, state-of-the-art canopy technology was investigated, and preliminary design and mock-up evaluations were performed for temporary roof supports for single-and dual-boom bolters and for transverse-mounted floor-riding canopies for a shuttle car and coal loading machine. The shuttle car and loader canopies were approved for further development, and the design, fabrication, testing, and certification were completed in Phase II. In Phase III, the Bureau of Mines furnished an FMC 6L shuttle car fur use in the evaluation of the canopy for 45 shifts. The shuttle car canopy was evaluated at Virginia Crews Coal Company in West Virginia. Efforts to secure an evaluation site for the loader canopy were unsuccessful. The loader canopy was shipped to Bruceton for possible future evaluation.

Jan 1, 1985

By John E. Kelley

The Bureau of Mines conducted a study to determine the feasibility of joining refractory metal compounds to each other and to oxide ceramics by a vacuum hot press-diffusion bonding method. Very satisfactory joins were made of ZrC to ZrB2, ZrN to ZrB2, ZrC to ZrN, and of ZrC, ZrN, and ZrB2 to Al203. Each of these join assemblies contained a mixture layer comprising 50 weight-percent each of the two end compounds. The mixture layer, sandwiched between each end compound, enhanced bonding and smoothed out the thermal expansion gradient between the two end members. Strength and thermal shock tests showed that the join areas of the ZrC, ZrN, and ZrB2 joins were stronger and more shock resistant than the parent materials. Also included in the joining tests was one each of TiC to TiB2, TiC to TiN, TiB2 to TIN, and TiC to ZrB2 joins. Each of these was well bonded, showing that the vacuum-hot-press method can be used for a variety of systems.

Jan 1, 1969

"INTRODUCTION Early in 1936 the Interstate Oil Compact Commission and other groups interested in forecasts of demand for petroleum requested the Bureau of Mines to make a physical inventory of crude-oil stocks in the United States, Accordingly, the 74th Congress appropriated funds for conducting such a survey during the fiscal year ended June 30, 1937. In the discussions and hearing 2/ relative to the need for the survey, the opinion was expressed that crude oil held in storage for long periods had lost so much of its gasoline content that the economic significance of total stocks should be discounted materially. Therefore, a primary objective of the survey was to make a physical inventory of the crude oil held in storage above ground and to determine the quantities and characteristics of the light fractions contained in the various stocks."

Sep 1, 1938

By Frank J. Weibelt

In accordance with provisions of the Strategic Minerals Act of 1939, the Bureau of Mines surveyed the chromite occurrences in California. The Seiad Creek deposit afforded excellent opportunity for developing reserves that could be used by the nation in case of critical shortages of the mineral. Subsequently an exploration and development program was undertaken in April 1941, which was concluded in October of the same year. Work included road construction, diamond drilling, drifting and crosscutting, surface trenching, and sampling.

Jan 1, 1949

By B. R. Mohal, S. Chander

"The adsorption and wetting behavior of freshly ground and aged coals has been determined in the presence of a nonionic surfactant. The amount of surfactant adsorption changes with the concentration and ""age"" of the coal. The freshly ground coal has smaller amounts of adsorption at lower surfactant concentrations than the ""aged"" coal whereas at large surfactant concentrations, the order is reversed . In the latter case, more surfactant is adsorbed on fresh coal than on the ""aged"" coal . . It is proposed that at low concentrations, the surfactant adsorbs through both hydrophobic and hydrophilic interactions with the molecule lying parallel to the· surface, whereas at higher concentrations surface micelles form at the hydrophobic sites. The wetting behavior correlates well with the adsorption behavior.INTRODUCTIONNonionic surfactants have many applications in the coal and mineral processing industry. They can be used as dispersing agents to modulate flotation, flocculation and filtration of particulates (1). They can also be used to increase the wettability of hydrophobic solids such as coal and can hence be used as dust suppressants (2,3). Although the adsorption of representative nonionic surfactants such as Triton N-101 (an ethoxylated nonylphenol with 9.5 moles of ~thylene oxide and HLB equal to 13.4) have been studied extensively on substrates such as calcium carbonate (4), silica (5) carbon black (6) and graphite (7), very few studies are available for coals. Coals differ from other substrates with respect to two important characteristics: 1) coal are porous and 2) coals consist of a patchwork of hydrophobic and hydrophilic sites (8). Since the adsorption characteristics of a surfactant are influenced significantly by the nature of the substrate the characteristics of the coals must be taken into consideration."

Jan 1, 1989

By N. S. Dalal, B. Jafari, F. H. Y. Green, V. Vallyathan

"INTRODUCTIONThe mechanistic details of the biological events leading to coal workers pneumoconiosis (CWP) are not yet fully understood, despite several decades of extensive epidemiologic1.2 and laboratory studies.2-6 Epidemiologic studies1.2 have shown, for example, that the incidence and severity of CWP differ markedly in the different regions and mines at comparable exposures, but laboratory investigations2-6 have demonstrated only partial correlation of the epidemiologic data with the differences in the mineral composition and the rank of coal mined. In particular, while epidemiologic data indicate1.2 direct correlation of the· prevalence and severity of CWP with the rank (i.e., % carbon content) of coal, this correlation has not been established by laboratory4'6 and animal exposure3 studies. In order to explain these results, in 1980 Artemov and Reznik' suggested that perhaps they arise from the fundamental differences in the surface properties of the coal. dusts inhaled by the coal miners and those used in the laboratory studies: while the miners inhale freshly fractured coal particles, henceforth called the 'fresh' coal dust, the laboratory studies generally utilize 'aged' coal dusts (i.e., dusts that have been stored for many days or even longer). Reznik and Artemov' used electron spin resonance (ESR) spectroscopy to show that the mechanical crushing of some Soviet Union coals generated organic free radicals and that the concentration and the decay times (hence the reactivity) of these radicals were higher for the coals of higher ranks. Since some of the radicals decayed within a few minutes in air, the authors surmised that while these radical species could lead to certain specific pathogenic reactions at the sites of mining operations, this might not be the case in the laboratory studies, due to the conventional use of 'stored' dusts which would be expected to contain significantly smaller free radical concentrations. This is consistent with the recent findings that, standardized, aged coal dusts exhibit minimal cytotoxicity. 8While the above mentioned work of Artemov and Reznik7 did suggest a possible new clue to the pathogenesis of CWP (i.e., the role of the coal based free radical species), no direct biological/cytotoxicity data were provided to show that 'fresh' coal dusts were, indeed, more pathogenic than the 'stale' ones. Because of the rather significant implications of the Artcmov-Reznik hypothesis to the understanding of 1hc biochemical mechanism and, hence, the strategies for the eventual containment of CWP, we have initiated a comparative study of the free radical formation and cytotoxicity properties of freshly crushed coal ·particles. As done by Artemov and Reznik, 7 we have used the ESR technique as the direct method of measuring the concentration and decay kinetics of the coal based free radicals. Our preliminary ESR studies on two Pennsylvania coals, a bituminous (carbon content 72 % ) and an anthracite (95 % carbon) coal, have confirmed the Artemov-Reznik finding that the crushing-induced free radical sites are higher on the coals with higher carbon content (i.e., higher rank).9-11 In the present work we describe our more recent results of a parallel study of the time dependence of the decrease in the free radical content of a freshly made anthracite dust (as measured via ESR) and that of the dust's cytotoxicity potential as measured by the extent of hemolysis of (sheep) erythrocytes. We have also investigated the effects of free radical scavengers on the cytotoxicity potential of the dust and deduce that indeed the free radicals could play a significant role in the initial events in the mechanism of the cytotoxic effects due to the inhalation of coal dust inhalation."

Jan 1, 1990

By John H. Hild

"INTRODUCTION Alunite occurs within a radius of 10 miles of Marysvale, Piute County, Utah, in veins and as replacements of igneous rocks. A number of each type of deposit was explored by the Bureau of Mines, in cooperation with the Geological Survey, under the Strategic Minerals program during 1942. The exploratory work comprised geologic and topographic mapping, diamond drilling,,bulldozer and hand trenching, sinking test pits, rehabilitation of old workings, sampling alunite exposures, and constructing and repairing roads.ACKNOWLEDGNENTSIn its program of exploration of mineral deposits; the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches-are under the supervision of Dr. R. S. Dean, assistant director.With particular reference to this publication, acknowledgment is given to Richard E. Mieritz and William E. Young, who assisted on the project at various times; P. T. Allsman, chief. Salt Lake Division, Mining Branch, who advised on exploratory problems and gave valuable assistance in preparing the report and illustrations; A. P. T. Schumann, for preparing the illustrations; and to Gordon L. Bell, Max Willard, and Eugene Callaghan, of the Geological Survey, who cooperated as representatives of that agency."

Nov 1, 1946

This information circular describes research the Bureau of fines has conducted to improve technology for recovering precious metals from low-grade resources. Many of the reported findings are recent, and some of the work described is ongoing. Topics discussed include cyanidation of carbonaceous gold ores to enhance gold recovery, a new method for precipitating mercury during cyanide leaching of gold ores, a staged heap leaching process to generate suitable solutions for direct electrowinning of gold, the use of anion-exchange resins to recover gold from cyanide solutions, and precious metals recovery from electronic scrap.

Jan 1, 1986

By R. E. Hershey

1. Reserves were estimated for three coal beds: Lantana, Sewanee, and Richland. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 34 million short tons as of Januray 1, 1954. Of this total, 15 million short tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient to permit making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By Gerhard Braüner

The report gives a review of the methods of predicting mine subsidence; these methods are used particularly in European coalfields. The methods are subdivided into two groups, based on mathematical expressions either for the trough profile or for the influence of infinitesimal extraction elements. The fundamental relationships common to all methods described herein are the principles of superposition and of equivalent extraction areas. The involved parameters are derived from field observations. For calculating horizontal displacements, their relation to the slope of the subsidence profile is applied. The time-dependent development of the subsidence process is characterized by the empirical "time factor." Modifications for the case of inclined strata are considered. A brief review of experimental and theoretical model investigations is given.

Jan 1, 1973

By David R. Peterson

This report presents a deep ocean mining operational simulation which is capable of describing the response of the bottom collection unit to specified mining ship maneuvers and the corresponding operation of the mining ship maneuvering system. Bathymetry, obstacles, collector and pipe dynamics and ship maneuvering capabilities are included in the simulation. The simulation is capable of evaluating the technical requirements and operating costs for specified mine plans, Results are useful in assessing mine size requirements and provide operating 'cost 'estimates useful as inputs to deep ocean mining economic feasibility assessments, The simulation is used to determine the consequences of obstacles to mining system operations in terms of impact on mine size requirements and reduced production arising from obstacle avoidance maneuvers of a towed (unsteered) collector.

Jan 1, 1979

By O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between, the Coordinating Fuel Research (C.F.R.) Committee of the Coordinating Research Council (C.R.C.) 3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36.-4/ Further reports have been issued describing motor gasolines sold during the succeeding summers and winters to the summer of 1941 and during the winter of 1942-43 and the summer of 1943 5/ No reports were made on motor gasolines sold during the winter of 1,) 41-42 and during the summer of 1942. The present report presents analytical data for 1,356 samples, representing the products of approximately 103 companies. As in previous surveys, the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium-price, and third-grade gasolines - and each group has been averaged separately. The number of samples, items and brands comprising each group is as follows: Regular-price, 770 samples, 286 items, and 94 brands; premium-price, 537 samples, 236 items, and 72 brands; third-grade, 49 samples, 31 items, and 18 brands. The meanings of these terms as used in the surveys are as follows:"

May 1, 1944

By P. G. Guest

MANY of the gases and vapors used in anesthesia form explosive mixtures with oxygen or air. Sources of ignition for these mixtures always have existed in operating and anesthetizing areas. When ether was first introduced, candles,5 gaslights, and coal stoves caused fires and mild explosions of the vapor-air mixtures. Today the chief causes of ignition are electrical. Fires and explosions are still much too frequent; and, because many of the mixtures are rich in oxygen, the explosions sometimes are very violent. Obvious sources of ignition, such as electric-power sparks and arcs in open motors, switches, and receptacles, as well as exposed incandescent wires and hot plates, usually are recognized by hospital personnel and corrected. A source of ignition that is not so obvious to many is static electricity. Until quite recently the presence of this hazard in a large majority of anesthetizing areas was not even suspected. However, numerous explosions-many of them fatal to patients-have been attributed, with good reason, to sparks from static electricity.

Jan 1, 1953

By Constantine C. Popoff

Several limestone deposits in western Washington were examined by the Bureau of Mines in 1946. This report presents data obtained from the investigation of limestone deposits in the vicinity of Arlington, Snohomish County, Wash. The work consisted of surface surveys and sampling. Samples were taken where complete, or nearly complete, sections of limestone were exposed or where individual beds were exposed at a number of separate .localities. Areas were cleaned by blasting prior to sampling. Channel samples were cut where practical; otherwise chip samples taken. Twenty-one samples were taken. The locations of the samples and the analyses are shown on maps accompanying this report.

Jan 1, 1949

By M. J. Dailey

This paper is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The property of the Silver King Coalition Mines Co. is situated in the western past of the Park City mining district, Utah, about 1 ½ miles southwest of the town of Park City, The elevation at the collar of the main shaft is 8,137 feet above sea-level.

Jan 1, 1930