Search Documents

By Abdulkadir Karadogan, Zikri Keti, Umit Ozer, Mehmet Aksoy, Ulku Kalayci

This paper presents an investigation about how the motions of blast induced vibration waves were affected by the presence of the fault planes. This study was carried out at Espey Open- Pit Boron (Colemanite) Mine in Turkey. Within the scope of the study, ground vibration components were measured for 8 shots using 9 vibration monitors, considering the direction of the fault. Measurement stations were located around the fault line that intersects the open-pit mine in the north-south direction and on different benches along the fault plane. Then, the data of the vibration components obtained from the 77 recorded events were analyzed and the results were presented.

Jan 1, 2012

By AJ Rorke

Blasting trials using Daveytronic Electronic Delay Detonator systems (EDD’s) were conducted at the Alpha Ferro Quany (Pretoria) and the Eikeboom Colliery near Witbank in November 1999. The objectives of the trials were to determine the influence of accurate hole firing on rock fragmentation, blast-induced vibration and blast throw. This paper provides an outline of the trials and an analysis of the results. The results were compared with a normal shock tube initiation system. Fragmentation was measured using video-imaging techniques at the hard rock Ferro Quarry for one conventional shock tube blast and two EDD blasts. No significant difference was measured in the fragmentation between the shock tube blast and the two electronic detonator blasts. Joint planes mostly defme the fragments at Ferro Quarry. The fragment sizing was therefore controlled mainly by the rock structure and the blast timing appeared to have no influence. Vibration measurements made at Ferro Quarry indicate that electronic detonators have a marked effect on vibration frequencies compared to shock tube systems. The more accurate detonators resulted in a narrower f+equency band at lower amplitude with similar timing. By modifying the blast timing, the dominant frequencies were changed. The electronic detonators had a significant positive influence, therefore on blast vibration and its control. The timing scatter measured from the shock tube blast was considerable, with measured inhole detonator scatter at 48 ms over a sample of 19 units. Surface delay periods less than 42 ms would therefore not be able to provide effective sequential firing. The scatter of the Daveytronic units was below the 2 ms resolution of the high-speed camera used to film the blasts. Reliable sequential firing, even at very short delay intervals was considered the main reason for notable improved throw in an overburden blast at Eikeboom Colliery. Blast throw was improved by 25% for the test blast.

Jan 1, 2000

By Chuck Kliche, Bill Clements

This paper relates some of the experiences, good and bad, of blasting adjacent to residences of the primary author during his 15+ years of field blasting in the Northern Great Plains region. During this highly-rewarding blasting career, the author has become aware of two major issues in residential blasting: 1) What we call “Risk/Reward Ratio.”Some questions that must be asked by the blaster prior to taking on any blasting job include: - Can we eliminate or minimize the risk? - Is the reward worth the risk? - Do I have a measure of “nervous confidence” about the shot? 2) Public Relations. Two key elements to public relations are: - Notification - Education All the education in the world to the adjacent populous of what’s happening, of blasting in general, or of what to expect from the blasting does little good without notification. Good public relations is a key to controlling the cost of liability in a litigious society.

Jan 1, 2009

By Raimo Vuolio

"Over the past 30 years, the Nordic countries have developed similar practices for estimating damage caused by rock blasting vibrations. However, over the last few years the risk of damage has sometimes been estimated by using international values, which have created unnecessary costs, since they are too conservative. This paper gives a proposal for Finnish blast vibration standards and a calculation model for the extent of the zones for building inspection, risk analysis, and vibration measurements. The international conclusion is that particle velocity is the best descriptor for limiting damage potential for structures. Over 900 000 vibration data recordings from 52971 blasts were collected for this paper during 1970-1989. They show that the most practical description is the vertical component of the peak particle velocity. As rock is a nonhomogeneous medium, it is hard to predict the need and scope of risk analyses, building inspection, and vibration measurements. As a large number of blasts were monitored for the recording of the peak particle velocity in several locations in Finland, and the data combined, it is possible to establish safe scaled distances for the calculation of the need and scope of risk analyses, building inspections, and vibration measurements."

Jan 1, 1991

By Michael Wieland

Sharp transient stress waves generated during the delay blasting of underground coal can damage unfired borehole charges remaining in the delay pattern. These tremendous stress pulses in coal bear a strong resemblance to underwater shock waves, despite differences in rise times, damping rates, and scaling relations. "Shock wave" terminology is adopted to distinguish the sharp transient waveforms propagating through the coal from the gas-driven stresses that rift the coal. Reported waveform characteristics of shock waves through underground coal were utilized to design a simulator test for rating the impact resistance of cap-sensitive explosives. Theoretical minimum borehole separations were determined for each cap-sensitive explosive from the requirement that worst-case waves hitting an unfired charge would not exceed its impact resistance rating. Rugged explosives have higher impact resistance and will function properly at smaller borehole separations. Additional work is required to verify the findings from the simulator technique and modeling relations reported here.

Jan 1, 1990

By Neal Lee, Braden Lusk, John Silva Castro

One of the most common assumptions regarding the use of ANFO versus utilizing 100% sensitized emulsion is that ANFO “turns over” the muck-pile better, due to the “higher gas volume” supposedly inherent in ANFO. This paper examines this assumption and provides quantitative data for analysis. Total gas volume from each product was evaluated using Orica’s I.D.E.X. Code analysis. This analysis was used to determine if gas volume is a significant contributor to differences in fragmentation and movement between blasts utilizing the two different products. A constant drilling and blasting cost per yard for given cut depth, hole diameter, stemming height and rock type was utilized. The cost per yard was held constant by adjusting patterns considering product, accessory, and drilling costs. Photographic fragmentation analysis, dig rates measured quantitatively through production tracking and time studies and qualitative information about the diggability of the blast provided through video recordings were used to evaluate performance. The data collected during the study is presented and recommendations are made regarding the performance of ANFO and Emulsion holding other variables constant for a limited number of blasts.

Jan 1, 2012

By Zhou Jiahan Wang Feng

This paper introduces the mechanism and the operating process of dike building by silt squeezing blasting. DBSSB (dike building by silt squeezing blasting) has the following advantages: shorter construction period (the construction period is decided only by the speed of rock materials filling)greater consolidation of the body of the dike, more structural stability, smaller settlement. Therefore by conventional standards the same dike can be designed with a smaller cross section than other construction methods, and at a reduced cost when enough rock materials can be provided in site.

Jan 1, 2006

By Thomas C. Jones

The purpose of this paper is to disseminate new information for nonelectric blasting in trenching and construction work. The presentation is not designed or intended to discredit conventional electric detonators or use of MS connectors and cord. Its sole purpose is to inform the S.E.E. of new and exciting benefits realized by the use of the Hercudet non-electric system in the construction industry.

Jan 1, 1984

By Roger Keller, Jason Ryan

A number of studies have evaluated excavation methods for the construction of subsurface facilities for a potential deep geologic repository for the disposal of nuclear waste at Yucca Mountain, NV. Many of these studies suggest that where TBM (tunnel boring machine) methods are not applicable and alternative mechanical excavation methods can not efficiently excavate harder rock drill and blast methods may be the most efficient means of excavation. However, a number of concerns regarding drill and blast applications have been raised in these evaluations, most notably the affects of blasting on the surrounding perimeter, as isolation of the waste by the natural barrier of the surrounding rock is a key element in the concept of a deep geologic repository.

Jan 1, 2001

By R. Alford

In the modern world of demolition safety is paramount and unnecessary or unquantifiable risks are not accepted (FasterCapital, 2024) and all risks must be kept As Low As Reasonably Practicable (ALARP) (BSI, 2017). This principle has led to a huge reduction in deaths in the last 50 years and the statistics continue to improve although this is starting to plateau (Beal, 2007). Under normal circumstances, this is now simply part of the normal way work is done and systems are in place to ensure both safety and economic profits are assured. What happens when the environment is less controlled and risks are unknown, such as after a natural disaster, war, an accident or a stand-up from a failed demolition attempt? A dangerous structure cannot responsibly be left alone with a fence around it so some action must be taken, but how can this be done safely and responsibly? An incident in Didcot, England in which half of a power station’s boiler house being prepared for an explosive demolition collapsed suddenly, killing four men in 2016 provides a useful case study of how technology, creativity and planning can be used to conduct complex demolition fully remotely to avoid any further risk to life.

Jan 21, 2025

By Mike Higgins

"The purpose of mining and its related industries is the removal of, and usually the subsequentprocessing of, material from the earth. This includes mining for minerals, quarrying for stone, and civilexcavations. Where this involves rock, the most common method is to fragment the rock by blasting. "

Jan 1, 1997

By Jesus Pascual, Jose Sanchidrian, Pablo Segarra

The surface vibration field in the area above an underground mine prior to its development has been investigated, in order to assess the vibration levels expected in existing buildings and in the planned mine facilities from future underground blasts. Shots of 50 and 100 kg of explosive placed in drillholes at depths of 100 to 150 m were fired, and the vibration events were recorded using an array of 40 seismographs in a 400 m square grid, covering a 2×2 km area. Contours of isovelocity were obtained for each shot, showing some directional transmission patterns. Propagation laws were obtained from the results of each shot and also from the bulk of data, both for the whole area and dividing it into four quadrants. The shift of dominant frequency with distance was also analyzed.

Jan 1, 2002

By K Lombardo

Numerous small- and intermediate-size cratering experiments have been conducted in Piceance Creek Basin oil shale at the Colony and Anvil Points oil shale mines near Rifle, Colorado. The purpose of these experiments was to evaluate scaling as a tool to infer the behavior of large-scale tests from small-scale experiments, to calibrate the hydrodynamic computer codes used to model explosive fragmentation of oil shale, and to investigate the influence of bedding plane orientation, natural joints, fractures, and the grade of oil shale on rock fragmentation.

Jan 1, 1983

By Felipe França Sitonio

Parameter’s control of explosives used in blasting operations have become more relevant over the years, bringing a better understanding of detonation performance. Giving into consideration that bulk emulsion density’s variation reflects directly on blasting results due to its importance in product sensitivity and velocity of detonation (VOD), blast designs are conducted assuming that cup density measurements are reliable and explosives gassing agents will perform as per specifications. Nevertheless, confinement conditions in boreholes like temperature, presence of water and surrounding circumstances of rock mass are often neglected on predictive modelling and off-site measurements. This paper describes the assembly of a device equipped with pressure sensors and its utilization in confined boreholes of an open pit mining operation, aiming to obtain in situ monitoring of density variation in several explosive columns. After we developed a software to get and process data of a hardware prototype and the device functionality was validated in water, oil and quarry mining experimental trials, 7 of 291 boreholes in a gold mine operation were chosen to be monitored with two probes each, placed at the top and at the bottom of the explosive column profile. The results obtained enabled a comparison between the bulk emulsion density variation when acting in different environments, since we selected boreholes with diameter of 101.6 mm (4 in) and 139.7 mm (5.5 in) and some with presence of water. Besides the increase of explosive density with depth related to hydrostatic pressure increase, we found an overall error of 6% in cup density measurements when compared with sensors placed at the bottom of boreholes and 2% when compared with sensors placed at the top of explosive column. These findings provide detailed insights into how bulk emulsion explosives behave in different circumstances including depth and borehole diameter, giving the opportunity to re-evaluate blast design parameters such as its geometry, sequence pattern, charging profile and explosive composition.

Feb 2, 2020

By Sanjay Sengar, Nabiullah Pingua, Saurabh Sahay

In India, more than 80 percent of the total of 557 million metric ton coal production comes from open-cast mines involving large overburden removal with average 1:3.5 stripping ratio which is going to in-crease in future. This operation consumes nearly 0.5 million metric ton explosives consisting of 80-85 percent bulk explosives and remaining 15 to 20 percent non-permitted large diameter explosives. Quali-ties of bulk explosives play an important role in rock blasting. Post blast results like poor fragmentation, tight mucking, toe problems, improper muck profile and lower productivity of mine may require chang-es in explosive loading factor (amount of explosive used per unit of rock blasted ). The explosive load-ing factor is an extremely important index to assess the economy of blasting operation.

Jan 1, 2014

By Lindsay Wade, Peter Dare-Bryan

Benches in surface mines often contain known areas of ore and known areas of waste, which must be mined selectively. When rock is blasted it not only fragments but is also physically, and non-uniformly, moved. Risks therefore exist of ore being lost if treated as waste and of mill feed being diluted by waste. Both possibilities carry serious fmancial implications.

Jan 1, 2001

By Lyall Workman

New mines are frequently located at altitudes above 3,000 meters (10,000 ft.). Drill selection must take the altitude effects into account, to insure high productivity and good bit life. In particular, compressors must be sized differently than for low altitude operation. A larger compressor is required to deliver adequate air to the bottom of the blasthole. Many drills in remote locations use diesel engines as the prime mover. Altitude effects on engine performance should also be considered.

Jan 1, 2007

By John T. Day, Lex L. Udy, Mark L. Thomas

When we consider that the purpose of blasting is to fragment rock or ore so it can be subsequently handled and processed, we can see that the cost of blasting, in reality, affects all downstream steps of the mining (and in some cases) production processes. The productivity of all subsequent operations is influenced by the degree of fragmentation of the primary blast.

Jan 1, 1987

By A T. Spathis, J J. Felice, W Klass

Cast blasting has become one of the most efficient ways to move waste rock in open cut coal mining. It is used at Mount Thorley Mine in conjunction with a dragline to move some of the overburden onto the spoil dump.

Jan 1, 1992

By Kenneth Eltschlager

The Surface Mining Control and Reclamation Act of 1977 requires that blasting be conducted so as to prevent injury to people and damage to public or private property. The three adverse effects are flyrock, ground vibrations and airblast. Blasting close to people frequently results in complaints of annoyance or damage. Federal and State personnel are responsible for evaluating the validity of the complaint. The elements to be evaluated include: reviewing blast logs, inspecting the mine, inspecting the house, measuring ground, air and structure vibrations, and predicting vibration levels. Computer spreadsheets, with their graphical capabilities, will be used to show how data can be cross tabulated to verify data accuracy. Complete statistical analyses of vibrations require more powerful software to make vibration predictions. Once all available data are gathered and verified, a decision on the complaint can be made.

Jan 1, 2001