Search Documents

By James H. Owen

Because of price structure, ANFO is normally considered to be the most cost effective explosive used in quarry blasting. Results indicate that bulk smulsion can be more cost effective in applications where hole sizes range up to 6.5 inches in diameter while providing the simplicity of single product loading and storage. This can be accomplished without any fragmentation and/or movement loss usually in patterns which are about twice the size of ANFO patterns, allowing the combined drilling and blasting cost to be less when using bulk emulsions. Examples are presented supporting this concept using actual field results along with some simple calculations which take into account differences in the products such as density, matrix and detonation velocity.

Jan 1, 1998

By Taner Sumer, H Altay Guvenir

Fragmentation in rock quarries is tried to be achieved by changing the specific charge, drill pattern and bore hole diameters by different experts. This paper is a brief summary consisting of the utilization of practical experiences of the other group on cost optimization procedure that takes into account blasting, transportation and crushing as a whole process and optimize the cost by defining the optimum gelatin based explosives to be used as a main primer of anfo in three different limestone and granite quarries, with similar rock characteristics.

Jan 1, 1993

By O E. Jr Crenwelge

Frequency domain, single-charge vibration signatures are used to interpret the characteristics of explosive impulse excitation and ground vibration transmission. The effects of charge height, charge splitting, and different blasting agents are first discussed. Then the effects of rate of change with distance of overburden material properties and layer or surface geometries are illustrated.

Jan 1, 1988

By William Hustrulid

Pre-split blasting is a primary technique for creating slopes with a minimum amount of unwanted damage to the remaining rock mass. Rock slopes created in such a way have both safety-related and economic advantages. The applications extend from road cuts to rock quarries to large open pit mines. For example, as deep open pit mines approach the end of their operating lives, slope steepening is one option to be considered. To be able to safely achieve and maintain steepened final slopes, good blast design techniques must be available and applied together with close operational control. Pre-split blasting is an important element in this slope creation process.

Jan 1, 2007

By J W. Simmons, T H. Antoun

"Rock fragmentation is an important component of explosive mining and excavation techniques andis the culmination of a damage accumulation process dominated by crack propagation. During the past 20 years, improved computer modeling of this process has resulted in new and promising computational tools for improving explosive mining and excavation procedures. This paper discusses one of these new computational tools, a computer model called BFRACT."

Jan 1, 1995

By A J. Rorke, U Chhika

"A series of tests was carried out on a dry blend of PPAN and LAN prills (LANFO). The objective of thetests was to determine detonation stability and VOD performance compared to ANFO. Heave andfragmentation results in the field were also evaluated visually. A number of factors were behind for.mulating this blend. A lower cost is combined with higher in-hole energies, but at slower reactionrates and lower peak borehole pressures. The resultant effect is improved heave characteristics andlower energy losses caused by inefficient crushing of the rock immediately around the borehole.The test results indicate that IANFO is ideally suited to blasting in softer midburden and overburdenrock types often encountered in coal strip mines."

Jan 1, 1995

By E. Contestabile, R. von Rosen, R. Guilbeault, R. Fouchard, P. Lightfoot

In August 1998, a truck loaded with 18 tons of blasting explosives, including over 13 tons of ANFO, left the road near Walden, Ontario. The crash caused a fire; approximately 30 minutes later a large detonation occurred, causing substantial damage to the roadway and local property. Although nobody was injured in the explosion, the consequences of a similar incident in a heavily populated area could have been catastrophic. Following the Walden incident, Transport Canada and Natural Resources Canada embarked on an extensive experimental program to determine the cause of the detonation. This paper describes part of that experimental program, designed to understand better the thermal decomposition of ANFO.

Jan 1, 2003

By Unknown

Threats to Industry Theft Potential

Jan 1, 2006

By Larry Schneider

"0 ne of the incentives that led to the development of non-electric shock tube initiation systems was the desire within the industry to improve detonator safety. And to the extent that nonelectric initiators are immune to the hazards of stray current and radio frequency energy found on normal blast sites, an advancement in safety has been accomplished. However, as a cautionary note, it is important to realize that there are still many hazards associated with any initiation system. While some of these hazards may differ from those associated with electric detonators, others are identical to those associated with any type of initiation system. For instance, contrary to what some uninformedblasters may believe, lightning remains a hazard when using nonelectric initiation as well as electric initiation."

Jan 1, 1995

By Ettore Contestabile, Cameron Thomas

Implosive connectors such as XECONEXTn have been used extensively for joining electrical conductors. This implosive action of explosives has also been used in other forms of high-energy metal working with excellent results. However, the inherent blast energy of these units can cause environmental side effects (especially airblast) which may restrict their use around inhabited areas.

Jan 1, 1994

By Johan Svard

"Two years of field testing have shown that blasting results are improved both in surface and underground applications when Nitro Nobel electronic detonators are used. The delay times canbe chosen with an accuracy of 1 millisecond over the entire time range (1 to 6250 ms). Since ordinary.high explosives have detonation velocities of up to 6000 metres/second, these high velocities make accurate and flexible delay times very interesting."

Jan 1, 1992

By Dale S. Preece

The computer program. DMC Qistinct Motion &de), which w&s developed for simulating the rock motion associated with blasting, has been used to study the intluence of row delay timing On rock mOtiOn. The munerical simulations correspond with field observations in that vmy short delays (< 5Oms) and vety long delays(> 3oOms) produce a lower percent-cast thao a medium delay (100 to ZOO ms). The DMC predicted relatio&lp between row delay timing and percent-cast is more complex than expected with a dip in the auve where the optimum timing might be expected. More study is required to gain a full undasranding of this phenomenoo.

Jan 1, 1994

By Junya Tokita

In Japan, packaged explosives have traditionally been used as the most common explosive for tunneling. Recently, some blasting systems such as ANFO with a kettle loader and emulsion explosives with a pump loader have been trialed in order to improve safety and efficiency of the charging process. There are issues with these systems relative to the Japanese market. ANFO dissolves in water easily, and generates ammonia gas when it contacts with concrete. Emulsion explosives need costly pump ing unit s, and there is a need to control residuals in the pump unit. Additionally, there are obstacles by Japanese law to site mixing of emulsion explosives.

Jan 1, 2005

By Randy Wheeler

The importance of having full wave form information for recorded blast events cannot be overstated. Knowing the peak particle velocity and the frequency at the peak are the tip of the iceberg. This presentation will focus primarily on using the FFT (fast Fourier transform) for detailed frequency analysis. Employing linear superposition to evaluate timing effects on amplitude and frequency will be discussed.

Jan 1, 2005

By Brian Gar Wingfield

Bulk explosive systems have developed from the infancy stages in the early sixties to a sophisticated process of the nineties. With ever changing bulk explosives technology, bulk delivery and loading systems needed to keep pace. Efficiency, as compared with packaged loading, was the keyword allowing faster loading of trucks and shots. Efficiency was also improved by the explosives coupling factor that bulk loading permitted.

Jan 1, 1991

By James W. Reil, Douglas A. Anderson, Steven L. Burchell

A total of 26 full-scale production blasts at three sites were extensively monitored with sophisticated instrumentation systems to determine the benefits of "ore. accurate detonators. The new and "ore accurate MS electric Masterdet detonator was tested against conventional detonators to determine any increase in productivity outputs. All blast design parameters between paired blasts were kept as constant as possible with the only difference being the inherent accuracy of both detonator systems.

Jan 1, 1989

By S. Paul Singh

Rock is a heterogeneous medium, a fact often ignored during blast design. In reality, the rock mass characteristics have a controlling influence on the outcome of a blast. If the optimum blasting results are to be achieved over a range of rock mass conditions, it is prudent to understand the role played by the geological features of a rock mass in producing overbreak around the periphery of an excavation. The field work was performed in a drift located in a geologically dominant rock mass and also included observations and assessment of blast damage at several operating mines. The blast damage was estimated on the basis of the half cast factor. The effect of rock strength, rock quality designation, orientation , frequency and aperture of joints, number and thickness of layers and hydrogeological conditions on blast damage has been described.

Jan 1, 2000

By T. Bernard, P. Dozolme

Electronic initiation devices appeared on the market more than 15 years ago and have definitely changed the rules of blasting. It becomes clear that this technology represents a powerful alternative to the traditional accessories. Electronic Delay Detonators (EDD) have attained solutions that were difficult and even impossible to achieve with the previous technology, thanks to the accuracy, usually inferior to one millisecond, and flexibility of the programmability range offering thousands of timing possibilities. Technological progress is long awaited to represent a step ahead compared with the last generation of products. In the case of electronic initiation, some limits nevertheless rapidly appeared, leading to the paradox of loosing operative and safety benefits, compared with the traditional technology it was supposed to outclass.

Jan 1, 2006

By Marco Antonio Falquete

A novel spark-generating tube, containing no explosive in its composition, is evaluated and compared with conventional shock tube. The product overcomes a series of problems found in conventional shock tube technology. The technologic development had multiple aims: to avoid transport and storage costs associated with explosives, to be more environmental-friendly, to obtain a high-velocity, hightemperature spark whose thermal performance could overcome poor heat transfer to the delay charge by gas convection at shock tube end, and that could cross barriers such as tight kinks, close knots, cuts, extreme environmental conditions, and long-term hot explosive emulsion exposure. The product of this development is evaluated and compared with conventional shock tube in a series of aspects and performance tests, including spark thermal performance (ignition of tougher, low sensitive delay columns, spark gap test), propagation in critical conditions of use (kinks, knots, cuttings), extreme environmental conditions (long-term exposure to hot emulsion explosive, extremes of cold, heat, moisture, underwater exposure), safety features (ignition through flame, open fire), and security against terrorist acts. Due to the safe characteristics of the tube, a series of demonstrations will be performed during the presentation. In nearly all tests and aspects, the spark-generating tube exceeds conventional shock tube, and in the rest equals shock tube, making it a more reliable alternative.

Jan 1, 2005

By Sarma S. Kanchibotla

In overburden cast blasting the explosive energy is used to move a significant percentage of overburden from the high wall to the spoil pile thus reducing the amount of material to be handled by machinery. However, the obvious trade-off between the extra explosive energy in the cast blast versus reduced dragline effort is complicated by an increased risk of damage to the underlying coal. This damage may not be obvious but inevitably leads to reduced coal recovery and may negate much of the benefit sought from cast blasting.

Jan 1, 1999