Search Documents

By G. V. Sedelnikova

Biohydrometallurgical studies were performed on the sulfide gold-arsenic concentrate obtained in treatment of refractory ore from a deposit located in northern Russia. Gold is disseminated in sulfides-arsenopyrite, pyrite and antimonite (their content is 10.0%, 30.4% and 0.7%, respectively). Gold extraction is only 11.8% by cyanidation. Results are given for test bacterial oxidation of the concentrate in continuous mode at temp. = 28~32°C using mesophilic bacteria and at temp. = 32~38°C using the association including moderate thermophilic bacteria. The paper shows that the use of moderate thermophilic bacteria allows to speed up sulfide biooxidation and reduce its time to 96 hours compared to leaching at temp. = 28~32°C for 110~120 hours. The optimal range of pH = 1.5~2.0 of biooxidation process was determined where bacterial solutions are produced with the molar ratio Fe:As > 3 necessary for precipitation of hard-to-solve, environmentally safe arsenical precipitates. Electron microscopy showed that sulfide biooxidation results in liberation of disseminated gold with nanoparticle-level sizes. High sorptive activity of carbonaceous matter and other compounds of bacterial residues cause low gold extraction into cyanide solution ? 28.7%. 10% resin load makes it possible to extract 88.1% Au. Aeration of pulp in calcareous medium enhances extraction to 95.7% and decreases cyanide consumption from 17kg/t to 8 kg/t.

Jan 1, 2014

By Y. Y. Li, Q. Chen, Y. X. Cai, Q. Zhang, S. Mao

"Due to the influence of combustion conditions, the fly ash produced by some power plants has the problem of high-carbon content. The unburned carbon in fly ash can be removed by flotation, and the decarbon tailings should reach the national standard level I fly ash. The fineness of the requirement is one of the important indicators and is also an important factor affecting the tail ash activity. In this paper,adopting two methods investigate the effect of particle size on the flotation index: one is direct flotation of fly ash, and the other way is wet grinding + flotation of fly ash, comparing the two methods and selecting the appropriate process,which provides a way for the effective utilization of fly ash. INTRODUCTION Fly ash is a solid waste discharged from coal-fired power plants. The annual amount of emissions of fly ash are very large in China. The amount of fly ash were discharged from coal-fired power plants are increasing gradually, and the amount of fly ash stored has exceeded 2.5 billion tons, but the comprehensive utilization of fly ash is not high, which brings about a huge environmental problems( Lu et al.,2011). Carbon is a harmful component of fly ash in cement and concrete application (Zhang et al.,2008). Fly ash decarburization is an essential link to improve the utilization efficiency of fly ash and the reduce pollution ( Yang et al.,2012). Carbon is selected from fly ash to make full use of fly ash resources and improve utilization of fly ash (Li et al.,2008). In this paper, the flotation decarburization of high-carbon fly ash is studied, through comparing the grinding and not-grinding processes, optimizing the separation process of fly ash, which provides a way for the effective utilization of fly ash."

Jan 1, 2018

By Ashish Kumar

High grade ore deposits in the world are fast depleting and the valuables in the low-grade ores are finely disseminated. The feed grade to flotation circuit is also declining. Attainment of suitable grind is preferred, which inevitably creates more fines of the gangue minerals to interfere with the flotation process because of the undue competition between the fines and the valuables for the collector ion adsorption. Besides the use of polymeric or long chain hydrocarbon depressants for the gangue mineral, microbial induced flotation also has potential to float minerals selectively. Thiobacillus ferroxidans and Thiobacillus thiooxidans adhere on the minerals to modify its surface properties and affect the minerals flotation acting as depressants. Hindustan Zinc has conducted laboratory studies to understand the adhesion of microorganism on the mineral surfaces and its impact on the selective flotation. The experiments were further designed to reduce consumption of depressing reagents for graphitic carbon, pyrite, and galena. Preliminary studies reveal that desired quality of concentrate can be achieved with reasonable recovery. Keywords: thiobacillus thioxidans, thiobacillus ferroxidans, bioflotation, microbial induced flotation

Sep 1, 2012

By V. V. Musaev, A. M. Klyushnikov, R. R. Galimov

"A study was made of chemical and material compositions of the oxidized gold-bearing ore of the Kochkovskoe deposit. It was demonstrated that examined ore consisted mainly of quartz, carbonate and feldspar with a gold content of 2.2 g/t and a silver content of 6.1 g/t. By means of agitation leaching tests it was founded that about 79-80 % of gold can be extracted from ore using cyanide leaching solutions. The achieved high-speed dissolution rate of gold was due to its presence in a finely dispersed state (less than 2.73 µm), which was confirmed by the research of Uralmekhanobr. It was proposed that the ore can be processed by heap leaching process using cyanide leach solutions. Technological studies on the modeling of the heap leaching process were initially carried out in percolators with a capacity of 5 kg on agglomerated ore. It was preliminary established that agglomeration should be carried out at a cement consumption of 12-16 kg/t, with the moisture content in pellets reaching up to 10-12 %. The best percolation leaching results can be obtained with ore crushed to the size of -20 mm. The maximum extraction of gold to the solution was 79-80 % while the L:S ratio reached 1.2-1.4:1.In cooperation with the research center of OJSC ""Berezovsky mine"" a semi-industrial heap leaching test was accomplished. The result of a test performed was an extraction of 78.5 % of Au and 21 % of Ag from ore to a pregnant solution. This extraction degree was achieved at a L:S ratio 0.9: 1. On the ground of results obtained, a technical regulation was developed for design of the heap leaching plant with the capacity of 500 thousand tons of ore per year.INTRODUCTION The ore of the Kochkovskoe deposit represents an important reserve of gold in the Zabaikal region. Of the upmost interest are oxidized ores, the processing of which can be carried out by heap leaching (HL) with cyanide solutions. The purpose of this work was to study the composition and to develop a technology for heap leaching of oxidized ore."

Jan 1, 2018

By Fuqiang Zheng, Shuai Wang, Feng Chen, Yufeng Guo, Guanzhou Qiu, Tao Jiang

"The direct reduced iron powder and Ti-V-rich material was prepared from vanadium titanomagnetite concentrate by solid-state reduction-magnetic separation. The result indicated that under the studied conditions, adding KS can effectively improve the metallization rate of pellets. 2% KS was well mixed with vanadium titanomagnetite concentrate to make the pellets. The green pellet was preheated at 900 ? for 6 min. The preheated pellet was reduced at 1050 ? for 100 min, then crushed and ground to more than 80% was below 0.045 mm. The direct reduced iron powder and Ti-V-rich material were separated from the slurry by wet magnetic separation at 800Gs. The TFe content of magnetic material was 90.63%, and the Fe recovery rate reached 96.53%. The TiO2 and V2O5 contents of Ti-V-rich material were 28.40 % and 1.64 %, respectively. The TiO2 and V2O5 recovery rates were 69.05% and 96.82%, respectively. 1. Introduction The ilmenite and rutile are the main titanium resources which can be used in the present technical level and economic conditions[1,2]. However, with the rapid development of China’s economy, the market demand of titanium products is increasing sharply. The current supply of ilmenite and rutile cannot meet the needs of chemical industry[3]. China is rich in vanadium titanomagnetite concentrate which contains abundant titanium and vanadium resources. The TiO2 and V2O5 content of vanadium titanomagnetite concentrate are usually about 7% and 0.3%, respectively[4]. Because the TiO2 and V2O5 grades are low, it generally requires pre-concentrated to Ti-V-rich material before extracting the titanium and vanadium. Therefore, it is vital to find effective processes for pre-concentrating the titanium and vanadium in vanadium titanomagnetite concentrate. There are many methods[5-13] developed or under development to pre-concentrate Ti-V-rich material from vanadium titanomagnetite concentrate, including the blast furnace process, pre-reduction electric furnace process, to utilized vanadium titanomagnetite concentrate are direct reduction-electric furnace smelting, sodium salt roasting-direct reduction-electric furnace smelting and direct reduction-magnetic separation and so on. The blast furnace process and other methods cannot effectively utilize the titanium and vanadium resource due to the technical or environmental problems[9]. In this study, the vanadium titanomagnetite concentrate was obtained from Panxi region of China, the reserves of which account for 11.6% of vanadium and 35.17% of titanium all over the world[3]. The preparation of direct reduced iron powder and Ti-V-rich material based on reduction-magnetic separation is proposed. The process utilizes a new catalyst for titanium ore reduction in rotary kiln followed by magnetic separation. Using this novel technology, the titanium-vanadium and iron are successfully separated. Compared to the traditional reduction of Ti-bearing ore, the reduction temperature reduced to 1050 ?, leading to higher efficiency, lower energy consumption and investment, and broader applications."

Jan 1, 2018

By A. M. Muhamedilova, S. M. Narbekova, L. V. Semushkina, D. K. Turysbekov, N. K. Tussupbayev

The research and development of new, more selective collectors in order to improve flotation efficiency represent one of the main priorities in the development of innovative technologies pertaining to flotation separation of various substances and minerals. The use of collectors’ mixtures is considered as the universal instrument for ensuring necessary proportion of chemically and physically sorbed collecting reagents in every individual case. Currently hard-dressed, refractory ores and man-made raw materials, which are characterized by low content of valuable components, fine dissemination of mineral assemblages and similar technological properties of constituent minerals, are widely involved in the recycling processes. The possibility of processing tailings, which are left after flotation beneficiation, has been considered in the case study of tailings of the Zhezkazgan beneficiation plant and the Tishinsk copper ore deposit with utilization of the modified multifunctional flotation reagents. Modified poly-functional collector is the mixture of composite Aerofloat, TC-1000 and butyl xanthate. Reactants ratio is 1:1:3. The advantage of the suggested flotation reagents is that they are composed of two polar groups and have a long hydrocarbon radical. This structure, being in the water during flotation process, plays a dual role: first, as a collector adsorbing on the mineral surface it produces metal complexes with polar groups in the form of bridges; second, apolar radicals flocculate valuable slimed components, thereby intensifying flotation process. It has been shown that flotation of Zhezkazgan tailings with utilization of the lesser modified reagent amount compared to butyl xanthate has enabled to produce crude copper concentrate with 13.0 % copper grade and 80.22 %recovery. Compared to the baseline technology, copper content of crude concentrate has been increased by 5.1 % and the recovery by 31.4 %. It is shown that tailings flotation of the Tishinsky field by applying modified collector allows for increase of the of useful components extraction in a collective concentrate with: copper 9.63 %, lead for 8.41%, zinc 9.2 %, iron 2.73 %, gold 3.57 %.

Jan 1, 2018

By B. Csoke

To improve the efficiency of the crushing/screening plant of Bazalt-Középko Kobányák Ltd. (Hungary), the implementation of computer aided quality control is planned. In the current phase, the R & D work aims at the solution of high-priority tasks: 1) Developing the process models, validation of the models by means of industrial measurements. 2) Developing the algorithm for the process control of the crushing/sizing plant. 3) Developing the suitable computer program. To develop the mathematical models of crushing (breakage and probability functions) and to determine the model parameters, the experimental industrial trials were carried out on hydrocone crushers of types Svedala H 4800 EF and H 4800 F, changing the gap size and crushing relatively narrow grain size fractions. Additionally, the parameters of the separation function for the screens operating in the system were determined. It was established that the crushing probability depends on the grain size of the feed (Y) and the gap size (s), so the breakage probability S, for each cone crusher, can be well characterised by the function formed using the ratio of these two parameters: SfYsf==. The distribution of the broken grains can be described reliably using the relative grain size distribution function B(? = x/Y) (usually Schuhmann-Gaudin- or Rosin-Rammler-shaped function). For the screens, the probability function ()2()111/NTx = xd ???---???? is suitable for cha-racterising the separation (where x? grain size, ?-open-area ratio, d ? rectangular screen aperture size, N ? number of appearance of the particle on a screen surface). Using these functions, the comminution circuits were described by means of vector/matrix equations. The calculations and measurements verified the reliability of the developed models and algorithms.

Jan 1, 2014

By O. Guven, I. Karaagaçlioglu, O. Ozdemir, M. Çelik

In this study, the effect of morphological properties such as shape factors and roughness of the glass beads on their flotation efficiency were determined using image analysis and profilometer methods. There is a considerable correlation between the shape factors, surface roughness and flotation behavior of the glass sample. These results indicate that as the particle shape is away from roundness and smoothness, it acquires more hydrophobicity.

Jan 1, 2014

By I. L. Grigorova

As a result of the main processes of the limestone treatment ? sawing, buffing and polishing, a technological waste is usually obtained. These final tailings consist of a water suspension with highly variable solid phase content and granulometric composition. Since the waste is conducted to a tailing pool or another place, this leads to environment pollution. In this work the slurry waste generated during the limestone processing in a Bulgarian limestone manufacturing company was characterized. The chemical composition, particle size distribution, solid phase content, whiteness, yellowness, abrasion, specific surface and density were determined. The possibility of obtaining building/construction materials from limestone processing waste was studied in a laboratory scale. The technological tests included thickening, filtration and drying of waste products. Continuous operation laboratory thickener was used. Coagulant Accepta® 8302 (aluminum sulphate solution) and anionic flocculant Magnafloc® 155 were found to be the most effective in the sedimentation of the products. Filtration tests were performed using a laboratory pressure filter. Drying tests were carried out in laboratory facilities using the direct heating method. On the basis of the laboratory results a technology for limestone treatment waste was developed. A production line for building materials from limestone slurry was set up. As a result the manufacturing company has a possibility to use circulating water.

Jan 1, 2014

By S. M. Javad Koleini

The aim of this research is to extract zinc from complex lead and zinc ore containing carbo- silicate lead and zinc minerals using sulphuric acid. Samples, taken from Dareh Zanjireh mine located in central of Iran, were subjected to leaching tests after calcination process. Experiments were planed according to the Taguchi statistical method. The calcinated samples contain 13.98% zinc and the constituting minerals being dolomite and zincate. Various parameters such as speed of mixing, temperature, time, solid to liquid ratio and pH were studied. A solid to liquid ratio of 1:6 gr/mL at 60°C and 800 rpm speed of mixing for 30 minutes resulted in a product with 85.96% zinc recoveries.

Jan 1, 2014

By Valentine Chanturiya, Irina Khabarova, Maria Ryazantseva, Igor Bunin

"XPS investigations of the influence of HPEMP - treatment duration on the surface composition for natural chalcopyrite and sphalerite are described. HPEMP is a video pulse with a nanosecond front lasting between 5 and 10 ns. The electrical field component can reach 30 kV, whereas pulses repetition frequency is 100 Hz. In general, the formation of metal-deficient surfaces, polysulphides or elemental sulphur and oxides/hydroxides, were determined during the treatment for both sulphides as well as the essential differences of the way of mineral surface transformation during the treatment. The chalcopyrite surface shows the formation of elemental sulphur under the HPEMP treatment at 103 pulses while appearance of unstable sulphite species was detected at the chalcopyrite surface within 5 seconds (0.5•103 pulses) under the same treatment conditions. The results indicate that the quantity of adsorbed water (at.%) is changed considerably during the HPEM - treatment depending on treatment duration for both minerals. The concentration of water onto the chalcopyrite surface decreased during 30 seconds (3•103 pulses) of the HPEMP - treatment and it rose after the treatment at 5•103 pulses. The inverse dependency was obtained for sphalerite surface. Single mineral flotation tests have shown the significant increasing of the minerals recovery."

Jan 1, 2014

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um

New modern water treatment technologies required for arsenic removal from waste waters contaminated extensively by various background sources from mining, industrial waste, agricultural waste, painting industry and natural geological bed rock system etc. Arsenic is a widely dispersed element in the earth's crust and exists at an average concentration of approximately 5 mg/kg. Arsenic (As) and heavy metals may be released from the mine wastes to the ground and surface water systems, as well as the geological environment due to their solubility and mobility. This research focuses on the effect of accelerated carbonation process for successful removal of heavy metal arsenic anions from artificial waste water and mining waste waters. This accelerated carbonation process is a simple and novel method with 85 ~ 88% removal efficiency. Carbonation has been studied as a process to further improve immobilization of solidified/stabilized waste and granular waste. After successful removal of arsenic anions from solid mining waste and its potential benefits for producing construction materials. Besides, the industrial and urban management systems are generating bulk solid mining wastes, and most often dumping them in open fields. To prevent the landfilling with mining waste, many efforts are being made for the recycling of different types of mining solid wastes with a view to utilizing them in the production of various construction materials.

Jan 1, 2014

By T. Fujita

A high-grade fluorite ore is converted into hydrogen fluoride to produce many kinds of materials containing fluorine. Recently, it is becoming necessary to use low-grade fluorite ore due to the depletion of high grade ore. The low-grade fluorites usually have impurities such as SiO2, P, CaCO3 and arsenic. The most impurities such as SiO2, CaCO3 and P can be removed by using flotation method. However, the removal of arsenic is difficult, and the arsenic contamination decreases the hydrogen fluoride production percentage. The novel technologies for processing low-grade fluorite ore are urgently needed, in order to lower the arsenic concentration to less than 100 mg/kg. In this study, the removal of arsenic from low-grade fluorite ore has been investigated by means of an autogenous grinding using tower mill in sulfuric acid aqueous solution and 0.3 mm zirconia balls in water. The nano grinding in water can prevent the dissolution of 0.3 mm size zirconia balls as grinding media by sulfuric acid solution. Experimental results showed that the arsenic concentration was reduced from 260 mg/kg to 90 mg/kg and CaF2 recovery reached 90% by this process.

Sep 1, 2012

By D. Krawczykowski, D. Saramak, T. Gawenda

"Annual world zinc consumption is as high as nearly 14 millions of tonnes. Approximately 50% share of zinc is used for corrosion protection in processes of continuous galvanization and the hot dip processes. In the latter, two zinc containing residues are produced: zinc ash and hard zinc, which constitute around 10% each. Paper concerns the method of possible separation of metallic zinc from the non-metallic zinc compounds from the zinc ashes – the waste product of hot dip galvanization process. The investigative programme covered the comminution tests of the feed (zinc ash) in selected crushers: jaw crusher, roller crusher and impactor. Results of investigations show that application of individual crushing device results in various breakage of the feed sample. Impact force caused the highest increase in finest particles size fractions of the product, while metallic and non-metallic fractions were comminuted differently. The compression force, in turn, caused the selective comminution, i.e. the breakage of metallic zinc was observed in a higher degree. The presented approach appears to be an economical supplementary method of initial recovery of metallic zinc from metallurgical zinc waste. For the high demands for the zinc in the world and the need of corrosion protection, the method presented in the paper helps in more effective zinc recovery and environmental protection.INTRODUCTION AND METHODOLOGY World production of metallic zinc during last decade shows a slight increase and in recent years its consumptions reach 14 millions of tonnes. Figure 1 shows world production of zinc in the time period 2009 – 2016. Main directions of zinc utilization include: - Galvanization - Production of zinc alloys - Brass and bronze production - Semi-manufactures of zinc - Chemicals The major share in global zinc consumption constitute galvanization process (Bright 2007). Two main types of zinc galvanization are: hot-dip galvanizing (HDG) and electro-galvanizing."

Jan 1, 2018

By Sergey Ulianov, Arkady Senchenko, Alexey Shvets, Arkady Bakotin

"This paper is devoted to ultrafine grinding of processing products. This process allows one to include into operation complex ores which earlier were considered as inefficient and economically inadvisable to treat. Fine dissemination of valuable component often does not allow its liberation via standard grinding in ball mills, and therefore requires modern methods of ultrafine grinding (UFG). An example of successful ultrafine grinding usage is its application for crude flotation concentrates regrinding before cleaner flotation stages. A problem often arises with a commercial copper concentrate production in the course of copper ore flotation. Crude flotation concentrate regrinding in a ball mill does not provide for good liberation of the material before cleaner stages. UFG application allows one to get commercial copper concentrate with copper grade of 20% and higher. Another example of ultrafine grinding application is its usage for highly refractory pyrite product received after gold-lead scavenger flotation of polymetallic ore. Earlier this product treatment was economically inefficient. At current application of ultrafine grinding down to 85% minus 20 µm and subsequent gravity processing it is possible to pass major part of gold (73.4%) into concentrate. The constraining factor for UFG application in processing may be the chemical activation of minerals. In the result of this, flotation selectivity may decrease. Therefore ultrafine grinding application extends the areas of efficient usage of metallurgical processes. New technologies allow increasing the level of valuable metals recovery."

Jan 1, 2014

By M. Saghaeian, R. Hejazi, L. Hosseini, M. Zare

Difference between plant feed specifications in practice and design feed is a problem that most of processing plants face during operating and commissioning. This topic has led to inappropriate operating and necessitates repeating the basic tests on new feed. Gol-E-Gohar fourth concentrate line with a capacity of 2 MTPY, located in Kerman province, is the first iron concentrate plant in Iran in which High Pressure Grinding Roll (HPGR) technology has been applied. Plant&apos;s feed consists of 30% AG mills pebbles of lines 1-3 and 70% run of mine crushed ore whose Fe=51%, Fe/FeO=2.5, S=1.7% and work index=15 kWh/t. Desired concentrate has Fe>68% and S<0.7%. After the plant construction and operation commencement, providing design feed was not possible due to the crushing unit`s not being complete, therefore the plant was fed by AG mills pebbles. For predicting optimal conditions of the plant and investigating the possibility of improving the current concentrate specifications, sampling from the new feed and laboratory and pilot tests was performed again. Studies showed that new feed has Fe=41%, Fe/FeO=3.5, work index=17 kWh/t. Results of laboratory tests with Davis tube device and pilot tests run using magnetic separators with simulating the plant`s circuit showed that with current feed, achievable recovery in industrial scale would be 75.52% which compared to plant&apos;s recovery in studied period (75.94%) shows that plant operated in optimal conditions. To improve the current concentrate specifications (Fe=66%, S=1.03%, Ferec=75.94%) and for achieving desired concentrate, samples were reground to four fractions with k100= 300, 212, 100, 45 and Davis tube tests were performed on each of the samples separately. Results showed that the fraction whose k100=212 µm or k80=200 µm has respective Fe and S grades of 68.27% and 0.681% which are consistent with the desired concentrate.

Jan 1, 2014

By T. N. Matveeva, T. A. Ivanova

"The article presents the results of the research aimed at development and testing of new effective reagents – collectors and green modifiers for more complete extraction of gold and platinum to concentrates at reduced loss with waste products. The main deposits of Au and PGM ores of Russia and abroad are presented by refractory raw material with the non-uniform finely-interspersed sulfide mineralization, submicron gold and platinum, the low metal content, non-uniform distribution of valuable minerals. and show low indicators of recovery. The main losses of precious metals (up to 15 %) at flotation are associated with thin slam tailings because of inefficiency of standard reagent modes.In the paper, the new trends in design of collecting agents for extraction of gold and PGM sulfide minerals and their application in flotation tests are substantiated. The original technique for obtaining the modified collector reagents – dithiocarbamate, dithiophoshpinate and dithiazine, incorporated non-ionic compounds that are able to generate stable complexes with gold and platinum has been developed. A novel class of collectors – cloud point polymers showed high flotation recovery of fine particles of gold and platinum. The original technique to create the mineral samples of natural sulfides with ""invisible"" or sub-micron gold on their surface designed helped to indicate the mechanism of selective adsorption of novel agents on Au and Pt-sulfide minerals. Extractive UV spectrophotometry, potential measurements, X-ray phase and spectral analysis, scanning electronic microscopy (SEAM), laser SIM and AFM microscopy were applied to analyze the adsorbed layer of modified reagents on the mineral surface. Selective hydrophobic covering on the surface of micro- and nanoparticles of noble metals provided an increase in their extraction during flotation. New reagent modes of modified collectors and green modifiers were tested in scaled-up laboratory flotation and the results obtained demonstrated the increased quality of the concentrates in terms of gold content by 1.5 times and higher gold recovery by 1.5-5%. The studies have been supported by Grants of the President of RF “Scientific School of Academician Chanturiya” NSh-220.2012.5; NSh-748.2014.5."

Jan 1, 2018

By V. P. Yakushkin, B. S. Ksenofontov

"Multistage model designed and used for more detailed description of floatation process. The study develops a new model of flotation kinetics description. It defines flotation as process that consists of several stages: air bubbles and particles are separate, air bubbles and particles form a raising aggregate, aggregate raises to froth layer. This description significantly differs from commonly used model, which is much simplified. The multistage model gives an in-depth description and considers different aspects of flotation. Experimental approval of the new model resulted in its accuracy.The model is to be used for description of all flotation processes’ kinetics of wastewater treatment. It helps in accurate designing of flotation treatment plants and may be used for further research of flotation process. Columnar flotation installation was designed by using multistage model. This installation consists of new tubular aerators with special ejectors, froth pressing system as well as unit of thin-layering lighting to catch microflotocomplex “particle – bubble”. Usage of tubular aerators allowed to aerate the overall volume of pulp. Due to use of special ejectors with longer mixing camera we state higher volume of small-sized floto-active bubbles. Use of multistage model allowed to optimize and get higher technological results of potash salts enrichment. Tests were conducted on centrifuges-floatation installation system. Meanwhile, froth concentrate contained mainly thin hydrophobic particles sized circa 0,1 mm. As a result we set that during floatation cleaning process of froth concentrate 95-98% of chloride potassium (KCI) is derived from foam.The final product satisfies production quality. Columnar floatation installation productivity was 17 – 21 m3/m2h, which is a high technological result. Columnar floatation installation is one of the best examples of concentrating equipment using nearly all technological indices."

Jan 1, 2018

By l. Bokányi, T. Varga

"The recycling of waste car tyres is a very important environmental task. The waste tyres usually are re-used or recycled by thermal processes like pyrolysis, gasification or incineration. The main problem associated with these processes is the sulphur content of waste tyres originated from the vulcanisation process, which pollutes the environment and the valuable products (i.e. pyrolysis oil) as well. In our research the desulphurisation of waste, mechanically prepared tyre sample was systematically investigated by the biosolubilisation with Acidithiobacillus thiooxidans, strain Karitas. Parallel, the experiments with sterile 9K nutrient medium were also carried out. It was found that the vulcanisation sulphur can be solubilised due to both the bio- and the chemical leaching, although the bioleaching is more effective. The solubilised vulcanisation sulphur then forms precipitates. The precipitates are forming in the bulk solution, as well as on the surface of rubber particles. The origin of the precipitates was investigated using XRD and scanning microscopy with micro probe. The origin of the precipitates is different: while in the process of the vulcanisation sulphur solubilisation with 9K medium the jarosite (KFe3+3(SO4)2(OH)6) forms, the course of the biosolubilisation with Acidithiobacillus ferrooxidans Karitas is accompanied by the formation of the jarosite and the halotrichite (FeAl2(SO4)4 · 22H2O) as well. The formation of the latter is the biomineralisation. The mechanisms of the bio- and chemical solubilisations are rather different as it was found and experimentally proved by several tests, and depends on the retention time of the solubilisation. Special efforts were done to elaborate the proper separation of the precipitates from rubber particles. Combination of intense dynamic stirring and recycling flotation process to remove the precipitates was applied for this purpose. The surface properties of synthetic jarosite were revealed using zeta-potential measurements at different pH and in presence of collectors. The parameters of the flotation were chosen based on the revealed surface properties of the precipitates. Finally, the sulphur recovery of the recycled rubber was achieved as low as <0.5%, sulphur content of it 0.17%, 12-times lower than that of the waste tyre sample after mechanical preparation."

Jan 1, 2018

By I. Grigoryeva, G. Voiloshnikov, V. Dementyev, N. Moskaeva, N. Voiloshnikova

"Adsorption processes with use of anion exchange resins are widely applied in the gold mining industry of Russia and the former Soviet Union. Anion exchange resin AM-2B and its analogs (with mixed basicity) are used as adsorbents. This paper focuses on the study of weak base anion exchange resin and its comparison with AM-2B resin. Different nature of the ion exchange groups of the adsorbents mentioned above provides essential differences in their properties both during adsorption and elution of gold and silver. Multistage gold elution and resin regeneration procedure is used for AM-2B resin whereas alkaline cyanide solution is used for weak base resin and allows for the reduction Capex and Opex in comparison with AM-2B resin. Anion exchange resins AM-2B and PuroGold S-992 were tested. Weak base resin is sensitive to pH of adsorption medium. Optimal pH value is 10.1-10.3 (at ?? >10.5 gold loading onto resin decreases dramatically). Adsorption isotherms for gold, silver, nonferrous metals, cyanide and thiocyanate ions from synthetic individual metal cyanide solutions were defined. Adsorption of all components onto PuroGold resin was lower than for ??-2? resin. Adsorption of metals from the solution with equal molar metal concentration (0.1 mg-equivalent/L of each metal) was also studied. The affinity of resins to cyanide metals complexes was established. Weak base resin has higher selectivity to gold in comparison with ??-2B resin and is less sensitive to ion composition of cyanide solution or pulp treated. Weak base resin was tested for gold recovery from gold ores. On the base of test results it was recommended to introduce this resin at some new plants in Russia. Commissioning and operation performance of gold plants confirmed efficiency of weak base resin use."

Jan 1, 2014