Search Documents

The uphole bench extraction strategy at EKJV Management Pty Ltd?s Raleigh Mine, requires simultaneous horizontal and vertical exposure of paste filled stopes. In order to prevent excessive ore dilution, the paste fill must be of sufficient strength to prevent failure during exposure. A numerical modelling methodology has been developed to accurately simulate the initial stress distribution within paste filled stopes, together with the strain-softening loading response of paste fill material. Due to the narrow orebody width and high deformation behaviour of the host rock mass, high closure strains are likely to cause a stiff, brittle fill material to undergo crushing failure upon exposure. The stability of paste fill exposures at the Raleigh Mine was determined by conducting a series of three-dimensional numerical models that incorporate the extraction, filling and exposure sequence of paste filled stopes. Stability charts for 2.5 m and 3.5 m wide simultaneous horizontal and vertical exposures have been derived based upon the numerical modelling results. Implementation of the stability charts has proved successful in limiting the amount of ore dilution from paste fill and provides a basis to optimize paste fill cementation and stability throughout the life of the mine.

May 1, 2007

By J. Flemming, R. O. Burt

"The Tanco pegmatite is located in the Bird River greenstone belt of southeastern Manitoba approximately 160 km northeast of Winnipeg (Figure 1). This pegmatite body was discovered in 1929 and subsequently attempts were made to exploit it for tin by Jack Nutt Mines Ltd. and later in the middle 1950's by Montgary Oil Ltd., who extensively developed but did not produce from, its lithium deposits. In 1966 systematic investigation of the pegmatite as a potential source of tantalum led to the founding of Tantalum Mining Corporation of Canada Ltd. (TANGO) in 1967 and production of tantalum concentrates from the Bernie Lake mine commenced in 1969. Tanco is currently jointly owned by Hudson Bay Mining and Smelting Co., Cabot Beryl co Inc. of Boston, and the Province of Manitoba. (Williams and others 1978, Burt 1979, Burt and others 1982), continued until the end of 1982, when, due to falling demand and prices, operations were suspended.During the 1970's Tanco had investigated the potential of the lithium orebody; carrying our research into both the concentration of the ore and into the production of lithium chemicals. However lithium chemicals were in an over-supply situation, due in part to the production from Chilean brine deposits (Buckley, 1983), and Tanco' s own plans were put into abeyance. The potential alternative market, the direct use of concentrates in the glass and ceramics industry, did not at the time justify the cost of constructing a new plant."

Jan 1, 1986

By A. F. Banks

"The last time I spoke to you the potash industry was at a low point. Markets were bad and the industry depressed. Many people had left and there was very little being done in terms of development. The current situation is very much changed. The oversupply conditions have given way to a very tight supply capability. All of the firms in the business are expanding in one way or another. These expansions will run from simple debottlenecking through to complete new projects.In New Brunswick, the Potash Corporation of America is proceeding with a new project and the Dennison - Potacan Project is in progress. In Saskatchewan, the Potash Corporation of Saskatchewan has an ambitious 2.5 billion dollar expansion program underway while those in the private sector are taking a somewhat less ambitious but equally significant approach to obtain further tonnage out of existing facilities.The significance of these expansions to mineral processors is that we can expect to see expanded employment opportunities and through necessity a surge in innovation and development in an industry that has been traditionally very conservative. This presentation will review potash processing with a view towards highlighting some of the more recent developments."

Jan 1, 1982

By Jean-François Dorion

La corrosivité des environnements miniers souterrains est un phénomène peu étudié au Canada. En plus de détériorer les systèmes de soutènement, la corrosion s?attaque aussi à divers installations et équipements souterrains. Cette étude, débutée en janvier 2007, est l?établissement d?une banque de données afin de caractériser les environnements miniers souterrains selon leur potentiel de corrosivité pour les systèmes de support de terrains. Pour ce faire, cinq (5) mines ont été sélectionnées afin de comparer les environnements : Laronde, Géant-Dormant, Niobec, Mouska et Doyon. À chacune des mines, trois (3) endroits ont été étudiés. Les résultats préliminaires démontrent une grande variabilité des conditions d?une mine à l?autre ainsi qu?à l?intérieur même d?une mine. La minéralogie des roches et du gisement influence la composition des eaux souterraines et la présence des sulfures joue un rôle important sur l?agressivité de l?eau et de l?air des mines de l?étude. Afin de déterminer le potentiel de corrosivité, plusieurs paramètres doivent être considérés et la mine doit être zonée selon l?agressivité des endroits.

Feb 1, 2008

By Leslie F. Sawatsky

Failure of drainage works is one of the principal threats to the sustainability of mine closure facilities but the risk can largely be remedied by appropriate design of mine closure drainage facilities. The feasibility of sustainable mine closure facilities that avoid failure of drainage systems needs to be established during the early stages of mine planning, before mine disturbances make sustainable closure uneconomical. Experience in mine development shows there is often enough latitude in mine plan development to incorporate measures with neutral economic consequence and positive environmental benefit. Project managers need to resist the temptation to develop mine plans and closure drainage plans independently. Integrated mine planning with effective inputs by environmental specialists and drainage designers may affect the overall mine configuration, footprint and schedule. Key issues pertain to the end pit location, waste dump configurations, pit infill elevations, fluid impoundments, diversion channel routing and preservation of flows to receiving waters. Guidelines with illustrations of suitable practices are presented to assist mine planners.

May 1, 2004

By Peter Raziszewski

"A ball charge dynamics model is presented. Simulation results are compared with observed data showing good correlation. Based on the charge dynamics models, a liner wear model is presented along with some wear simulation results. Using the charge dynamics model with the liner wear model, it is possible to envision the predictions of mill power consumption as a function of liner wear. Further work is needed to validate the liner wear model.IntroductionFrom a process control point of view, industrial systems can be considered stationary or non-stationary. For example, the physical properties, such as geometric and/or material, of a system considered stationary do not change with time. However, this is not true for non-stationary systems such as those found in the mining industry where process dynamics are often violent with wear being an intrinsic process phenomenon.In this paper, a model for ball charge dynamics will be presented along with a description for liner wear. Simulation results for power draft prediction using the charge model will be compared with observed data. Further, liner wear results will also be presented."

Jan 1, 1997

By George Hope, Brigitte Lacouture

"The Red Dog mine has increased mill throughput most years since start-up. Although flotation equipment has been added over the last 10 years, the Red Dog metallurgical performance has been restricted by a lack of adequate flotation capacity. Two reduced tonnage trials conducted in 1997 as well as numerous SAG relines have consistently indicated the potential to significantly increase both zinc concentrate recovery and grade with additional flotation capacity. Later in 1999, a new circuit was designed with increased flotation capacity while simplifying the current circuit, providing for three stages of dilution cleaning, and creating a retreat section. The purpose of the retreat section is to target the more complex particles and allow the chemical environment to be fine tuned for improved iron depression. In total, 21 Outokumpu OK50 (50 m3) mechanical flotation cells and four 3.66 mØ column cells were added to the current flotation circuit. The VIP (value improvement program) mill optimization project is also addressing thickening, water treatment, and power generation issues and has a total budget of US$105 M. Start-up of equipment was phased in to minimize the impact on current operations and the project was completed by the end of 2001. IntroductionRed Dog Operations started production in November 1989. The mine is located above the Arctic Circle in northwest Alaska. It is linked by an 80 km road to a port-site facility where the concentrate is stored. Concentrate is shipped to markets throughout the world during the one hundred days of open seas. As of January 2002, the Red Dog main pit had 38.4 Mt of reserves grading 19.2% Zn, 5.3% Pb, and 102 g/t Ag. Additional reserves and resources contribute an additional 72 Mt at 15.6% Zn, 4.2% Pb, and 78 g/t Ag. Red Dog is a Mississippian to Permian, black shale-hosted, zinc-lead-silver deposit located in the DeLong Mountains, western Brooks Range, Alaska. All the rocks associated with the mineralizing event are considered to be part of the exhalite rock package. Silicification was a dominant component of the mineralizing event and the host shale has been silicified and locally resembles a chert. The major sulphides in decreasing order of abundance are sphalerite, pyrite, marcasite and galena. Most of the deposit’s silver occurs within the crystal structure of the galena. The dominant ore mineral, sphalerite, is very fine grained to amorphous and is commonly intergrown with silica. Ore textures are massive, fragmental, chaotic, veined and rarely show classic sulphide sedimentary layering. The upper portion of the orebody has been physically and chemically weathered. Oxidation has altered the sulphides to sulphates. The zinc and iron sulphates are very soluble and are readily depleted from the weathered cap, while the lead sulphate is residual and is, therefore, enriched."

Jan 1, 2003

By Bern Klein

Motivation for Improved Energy Efficiency in Mining ? Canada potentially adopting Greenhouse Gas Emissions and Intensity Legislation in 2013 ? BC -Climate Action Plan and Energy Conservation Agreement in 2008 ? BC Energy Plan 2007 -BC Hydro is mandated to save 50% of new load growth ? TSM Initiative -Energy Management, Energy Reporting, Setting Energy Targets, GHG Management BC MOU for Energy Conservation Agreement -MEMPR, MABC, BC Hydro

May 1, 2010

By S. G. Hardcastle, C. K. Kocsis

"Worldwide, metal mines are going deeper. For example, in Canada there are six such mechanized mines planning production at 3000 m (10 000 ft). Working at such depths challenges all aspects of mining including the provision of ventilation to supply an equitable working climate for personnel and machinery.This paper explores the overall challenges of supplying ventilation in Canada’s deepest mines and how the volumes required could be minimized. This is essential because it must be remembered that ventilation and refrigeration are not only costly items to supply, but the magnitude of their cost is also very sensitive to the volume supplied. For the primary ventilation system this is obvious because of the cubic relationship between volume and cost.In deep mines, the main function of ventilation is the removal of heat transferred from the strata and generated by the mining machinery, and the air volumes supplied are designed accordingly. The second consideration is the removal of other pollutants that could be harmful to humans such as diesel and explosive fumes. However, the need for ventilation at its present design levels could be reduced. This paper discusses the implications of such technologies as: tele-remote mining and alternatives to diesel equipment on the magnitude of the volume supplied; ventilationon- demand which recognizes ventilation as a costly and limited resource; plus other aspects, such as the benefits of controlled recirculation, local cooling, and possibly heat rejection back to the strata to gain further advantage from new developments.Furthermore, this paper advances the need to be able to design ventilation systems more cost effectively and how such new advances as process simulators can be used in conjunction with ventilation simulators to explore the diverse options that could affect the air volumes required and provide more realistic economic data upon which to base design decisions."

Jan 1, 2004

By C. H. Dionne, J. A. Holmes, B. J. Huls

"Falconbridge Limited is presently developing flowsheet alternatives for implementation at the Strathcona Mill. The main thrust for change arises from the need to reject more pyrrhotite from the concentrate. To maintain appropriate levels of sulphur in the smelter concentrate, however, enhanced removal of non-sulphide gangue minerals must be realized. This could best be done in the Non-magnetics flotation circuit.Laboratory investigations were followed by an on-stream pilot test at Strathcona. The application of a column cleaner on the Non-magnetics concentrate resulted in significantly lower levels of fine gangue at equivalent sulphides recovery.This paper discusses the laboratory and pilot testing and results, with a focus on piloting. Also included is a discussion of the Strathcona Mill Flowsheet and the role of the Nonmagnetics flotation circuit.INTRODUCTIONFalconbridge Ltd. is currently developing means to reduce atmospheric sulphur dioxide emissions. One alternative is a reduction in the amount of pyrrhotite in Strathcona Mill concentrate, which reports to the smelter. Pyrrhotite in the Falconbridge ores contains an average of 39 percent sulphur and 0.64 percent nickel. By comparison, pentlandite contains an average of 33 percent sulphur and 34 percent nickel.A consequence of the rejection of pyrrhotite is a decrease in the sulphur assay in the remaining concentrate. This decrease causes downstream difficulties in the roasting process. Therefore, the content of non-sulphide gangue in the mill concentrate must also be reduced in order to maintain sulphur grades adequate for roasting. The resulting concentrate will have lower sulphur dioxide emissions while maintaining nickel production."

Jan 1, 1991

By Paul H. Atkinson

"Sampling in the mineral processing industry has always been a subject which has received considerable discussion. There have been many volumes written on theory, techniques and practical application of sampling. However, until recently, the companies were not completely aware of the potential savings available with properly designed sampling systems both to assist in pieces: control and final product values.Definition In our discussion today, we will define sampling as the operation of removing a part, convenient in quantity for analysis, from a whole, which is of much greater hulk, and removing it in such a way that the proportion and distribution of the quality to be tested, i.e. size of particle, moisture content, specific gravity content, mineral and chemical composition, are the same in both the sample and the whole.Application It has been well established that undetected errors can result in large economic losses, thus most firms depend upon some type of sampling and sample analysis as a control in their continuous processing of materials. Despite the large investment in facilities and personnel the ""analysis"" of a sample can be no more accurate or reliable than the sample on which it is being based. The importance of sampling is recognized by a great many but it is appreciated by only a few, largely because it is sometimes one of the items which is taken for granted."

Jan 1, 1976

The stability of paste fill bulkheads forms an integral part of a successful paste fill system. Bulkheads are constructed at the draw points of open stopes to contain paste fill while the initial pour cures and forms a consolidated plug. Mobilization of uncured paste fill as a result of a bulkhead failure can lead to significant consequences, including endangering the safety of personnel, property damage and production losses and delays. The loading conditions in the paste fill and the resultant lateral loads on the bulkheads are complex and are dependent on many factors. This paper presents a case study of several paste fill bulkhead failures; the results of an in-situ pressure monitoring program to ascertain the pressure loads, and the subsequent paste fill bulkhead evaluation.

May 1, 2007

By Evelynn Stirling

Agenda ? Emissions legislation ? Cummins Tier 4 Technology ? Cummins Experience with Technology ? Operation and Maintenance Impact The Emissions Challenge ? The 2014/5 emissions regulations present the most significant challenge to our customer?s diesel powered equipment design and operation in recent history? ? ?and Cummins has the solution.

Aug 1, 2013

By Son Hye Jin

Abstract ? KHNP is participating in the construction of Nuclear Power Plant both in Korea and UAE. ? We want to improve our construction project management process. ? So we are now developing the process model on nuclear power plant construction management. ? For the effective adoption of this process, we are planning to develop IT system. ? For the first step, we were established the Information Strategy Plan

Aug 1, 2013

By S. Schwartz, T. Bilney

"Over recent years a number of techniques have been developed as part of the AMIRA1 P9 project to represent mathematically or measure directly sub-processes occurring in flotation cells. These include the determination of:•,?a machine parameter (bubble surface area flux, Sb);•,?a froth parameter (froth recovery, Rf );•,?entrainment and drainage parameters (???and d); and•,?an ore floatability parameter (Pi).These flotation parameters allow the plant engineer to develop a model of the flotation circuit that can be used as a powerful tool to diagnose the performance of that circuit. The recently developed JKSimFloat V6 flotation simulator uses these parameters to predict the flotation circuit performance that would arise from changes in operating conditions and circuit configuration.This new flotation technology was applied to the Placer Kanowna Belle Gold Mine in Western Australia. A series of plant surveys, cell characterisation measurements and laboratory batch tests were conducted to determine the flotation circuit model parameters to be used within the JKSimFloat V6 simulatorA thorough flotation circuit analysis was then performed at Kanowna Belle using JKSimFloat V6. The recommendations that were provided by this circuit analysis have resulted in large improvements in the flotation performance at Kanowna Belle. These include a 1.3% increase in flotation gold recovery and a substantial decrease in operating costs. The analysis is still ongoing, however, the benefits already obtained from applying this technology have resulted in a US$1.3 million a year improvement to the mine."

Jan 1, 2005

By Dayang Datu Khalil, Charle Amoah, Fred Kock

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By James Ransford Dankwah

This work investigates the effect of waste plastics addition on the reduction of iron oxide by sawdust. Composite pellets of iron oxide containing sawdust (SD), high density polyethylene (HDPE) and blends of SD/HDPE were fired under argon in a horizontal tube furnace at temperatures between 1300 and 1500 °C. Reduced samples were weighed after 10 minutes of reduction and the extent of reduction was calculated from the measured oxygen contents of the compact. The results showed improved extent of reduction when SD was blended with HDPE. The highest extent of reduction was achieved at SD:HDPE ratio of 2:3.

Jan 1, 2014

By Louise Pearce

?Environmental and social impact assessments (ESIAs) are: ??process-driven and scientific processes ??The process entails a number of steps and procedures which result in obtaining a licenceto operate ?and moving more towards a social license to cooperate. ?However, the primary premise of ESIA is to facilitate the consideration of environment and the communities in planning and decision-making which would ultimately make it possible to arrive at decisions that are ?sustainable?. ?Hence, ensuring the development of the mining sector on a sustainable basis is a critical challenge that needs to be addressed by the global community.

May 1, 2011

By J. M. Simard, S. Morissette, P. Coursol, P. Mackey

A new, powerful model is presented that focuses on plant logistics and scheduling aspects of the smelting, converting, fire refining and casting operations at the Horne smelter. This plant complex is the largest custom copper smelter in North America. It handles a wide range of feeds and utilizes a number of proprietary continuous and batch technologies that require good scheduling in order to maximize plant capacity and efficiency. The present model was developed by Xstrata Process Support, in collaboration with the Horne smelter, and uses the Arena® software to evaluate the impact of a number of plant variables on the annual copper capacity of the plant. Model development was carried out by Xstrata Process Support, in collaboration with the Horne smelter, through the effective combination of process chemistry knowledge and detailed knowledge of the plant operation (including all material flows and transfers, as well as information such as operating on-line times, plant stoppages and also scheduled and unscheduled maintenance activities). A number of case studies were then examined, including the impact of anode furnace and casting cycle times on annual copper capacity and the impact of a one-crane mode of operation in the converter aisle, which normally operates with two cranes in service. The model predictions were found to match actual plant results very well. The present modelling of plant logistics and the scheduling aspects were found to add important dimensions at the plant with regard to projections of the real-life plant capacity. As demonstrated in the present case, this type of model and application can have a significant impact on optimizing operations at a given plant. This impact is particularly important in the current market environment, where emphasis is on maximizing plant output and lowering costs. These models can help yield the easily obtained gains that are clearly desirable in these times. Xstrata Process Support has developed Arena models for other operations and is available to explore new applications for a win-win situation at other plants, including mines and concentrator operations.

Jan 1, 2009

By R. Tessier, C. R. Larsen

"INTRODUCTIONOn November 10, 1982 Nor and a Inc signed an agreement with Golden Sceptre Resource Ltd. and Goliath Gold Mines Ltd. to construct a mine and milling facility.The Golden Giant mine is located in the Marathon area of north - western Ontario, immediately north of Highway 17 and about- 3.5 km west of Highway 614.With the exception of selected unit processes, the mill was designed for a nominal throughput of 2500 tonnes per day with early operating data to be used to identify sections requiring possible expansion to achieve an ultimate throughput of 3000 tonnes per day.Commissioning of the highly instrumented milling complex which includes crushing, grinding, cyanidation, and carbon in pulp processes commenced in February 1985. After water testing various sub-circuits from grinding through tailings, waste ore was introduced to ensure proper mechanical and electrical operation of process equipment.The first ore was milled as a mixture with waste on March 4, 1985. The first gold bullion was poured April 6, 1985.Initially, ore was only available from mine development at a rate of 700 t/d, which was milled at a minimum rate of 1200 t/d. While regular weekly shut downs of two to three days was useful for mechanical maintenance, changes, and modifications, process tuning was more difficult due to the non-steady operation. As increased quantities of ore became available, regular weekly shutdowns tapered off and process operation improved accordingly. For testing purposes and as ore was available, mill throughput was increased regularly to 2300 t/d and for very short periods of time to nearly 3000 t/d.No major design or operating problem has been encountered to date. The following is a brief description of the milling process and various operating highlights. Process flowsheets are shown in Figures 1 through 6."

Jan 1, 1986