Search Documents

By A. Hartikainen, M. Rinne, F. Johansson, R. Yorke, L K. T. Uotinen, E. Korpi, J. Antikainen

"In order to determine the in-situ shear strength of rock joints, large scale testing is required. However, this is both expensive and difficult to execute. One possible method to overcome this may be to use photogrammetry to capture large joint surface roughness in-situ and downscale it to replica samples, which could be sheared in laboratory. In this paper, as a first part in such a method, a technique to digitize surface roughness and to produce replica samples for laboratory shear testing from a larger joint sample are presented. First, a thin granitic rock slice with dimensions of 1.75 m x 0.95 m of granitic intact rock was chosen for the study. The joint surface is fresh and created through tensile induced splitting. The large joint sample is digitized using photogrammetry. Then, one fullscale 1.7 m x 0.6 m geometry is cropped from the digitized joint geometry and then subsamples at 10x, 7.5x, 5x, 2.5x and 1x scales. All sub-geometries are scaled down digitally to produce 0.17 m by 0.06 m geometries. The geometries are used to make casting molds both positive and negative to produce samples with perfect matedness. The casting molds are 3D printed in polylactic acid plastic and C60/75 concrete is cast to produce a replica series. In addition to the creation of this replica series, two pilot replicas are also tested using a portable shear box with a 0.5 MPa normal pressure. The results from the pilot rounds are presented and discussed. Finally, suggestions for future research are given.INTRODUCTIONThe rock mass strength is in many cases controlled by the shear strength of rock joints, especially in hard rock masses. The shear strength is generally found to be influenced by several parameters, including normal stress, the basic friction angle of the intact rock, the joint surface roughness, the joint wall compressive strength, the matedness of the joint surfaces, weathering and infilling. The effect of these parameters for the joint shear strength can be evaluated in laboratory scale. However, the shear strength is known to be scale dependent. How the scale effect influences the strength is not fully understood. The general consensus is that the shear strength decreases when sample size increases, i.e. a negative scale effect (Bandis et al. 1981). However, some studies have presented contradictory results, see for example Hencher et al. (1993) and Kutter & Otto (1990). The extent and nature of the scale effect is still a question of debate (Tatone & Grasselli 2013)."

Jan 1, 2015

By S. Nakamura, K. Fujiwara, S. Hirosawa, S. Tsukamoto, Y. Koshino, Y. Aruga

"In this study, hardness test, differential scanning calorimetry(DSC)and transmission electron micros copy were carried out to investigate the age-hardening behavior of Al-Mg-Si alloy with a Mg+Si concentration of 1.5mass%, and a Mg/Si ratio of 1.0. Pre-aging treatment was conducted for the solution-treated and then water-quenched specimen at 100, 80, 60, 40, 20 (natural aging), 0 and -20°C for 20min or 5h, followed by artificial aging at 170°C for 20min. It was found that when pre-aging time is prolonged from 20min to 5h, the bake-hardening response is deteriorated irrespective of the pre-aging temperature. In particular, the specimens subjected to pre-aging at 20-40°C for 5 h hardly increased the hardness with the subsequent artificial aging. From the results of DSC measurement, it was suggested that as pre-aging temperature is lowered, the amount of solute clusters formed during pre-aging, i.e. Mg-Si clusters and Si-rich clusters, is decreased, but the ratio of Si-rich clusters is increased, resulting in the deteriorated bake-hardening response.INTRODUCTIONIn recent years, Al-Mg-Si alloys have been widely used forautomotive body panels due to their excellent characteristics such as high strength-to-weight ratio and good formability. Their strength is increased not only by artificial aging during paint-bake treatment; i.e. “bake-hardening”, but also when kept at room temperature(RT);i.e. “natural aging”, in association with the suppressed bake-hardening response. Such a “negative effect of two-step aging” has been a serious problem because Al-Mg-Si alloy coils are unavoidably maintained at RT in the manufacturing process of body panels; e.g. shipping and storage. However, it was reported that pre-aging above 70°C before the two-step aging can restore the bake-hardening response, and such an improvement is related to the formation of solute clusters(Sato, 2006; Abidet al., 2010; Takaki et al., 2014; Zandbergen et al., 2015). From the comprehensive analysis by three-dimensional atom probe (Aruga et al., 2014 and 2015), it is believed that Mg-Si clusters formed during pre-aging transform into the strengtheningß"" phase, whereas Si-rich clusters formed during pre-aging act as a detrimental precursor of ß""phase. In this study, it was aimed to investigate the effect of pre-aging conditions, especially pre-aging temperature and time, on the formation of solute clusters during pre-aging, in order to elucidate the mechanism of the age-hardening behavior of an Al-Mg-Si alloy."

Jan 1, 2018

"Bay d'Espoir is in the approximate center of the south coast of Newfoundland. The geology of the area can most conveniently be considered in terms of three units: (1) an Ordovician or older polydeformed terrain termed the Little Passage Gneisses; (2) a Lower-Middle Ordovician volcano-sedimentary sequence assigned to the Baie d'Espoir Group; and (3) granitoid intrusive rocks of mid-Paleozoic age. Mineralizing events accompanied the formation of the latter two units.The Baie d'Espoir Group comprises a dominantly sedimentary sequence of pre-Middle Ordovician shelf and distal turbidite sediments deposited on the eastern margin of Iapetus. A significant volcanic component is, however, present in the Isle Galet Formation, consisting of up to 30% felsic volcanic rocks interbedded with sedimentary and epiclastic rocks. The Isle Galet Formation hosts several disseminated to thinly bedded Pb-Zn-Ag occurrences associated with altered felsic tuff and graphitic shale. They occasionally grade laterally into pyrite iron formation and appear to have been deposited in a very distal volcanic environment. The Isle Galet Formation is a time equivalent of the mineralized pre-Caradocian island-arc sequences of central Newfoundland, but differs from them both in style of volcanism and in the nature of the associated mineral deposits. It is, however, comparable in many respects to mineralized volcanic sequences in the La Poile Bay area of southwestern Newfoundland.Mineralization associated with granitoid rocks in Bay d'Espoir is best developed around the southeast margin of the North Bay Granite, where two-mica leucogranite forms a marginal phase. Numerous minor base metal showings occupy quartz, quartz-carbonate and barite veins in the adjacent sedimentary rocks. Collectively, the showings exhibit a well-developed, zonal pattern around the granite margin; molybdenite (±py, cpy) predominates near the contact, giving way outward to galena (±sph, py, asp, cpy) and eventually to stibnite (±asp, py) at the periphery. Mineralization associated with granites in similar settings elsewhere in southern Newfoundland includes tungsten in the Grey River and Granite Lake areas and molybdenite in the Rencontre Lake area."

Jan 1, 1982

By O. D. Maurice

Feldspar mining in Canada came to an end during 1972 after many years of continuous activity. The deposits are not exhausted and the domestic demand for this product is expected to continue at about the same level as in recent years. The size of the industry does not justify the installation of expensive equipment in the mills, but it is believed that a modest profit could be made by a small operation using rudimentary methods of separation. Largescale and accurate mapping of the pegmatite dykes could help in planning mining operations for a better recovery of a uniform product.

Jan 1, 1973

By Gordon G. Duncan

Historical Sketch Occurrences of native copper have been known along the Arctic coast of Canada, especially in the vicinity of the. Coppermine river, since the early part of the eighteenth century (See map, Figure 2, insert). In 1769, Samuel Hearne, a clerk of the Hudson's Bay Company at Fort Churchill, was sent to explore the 'copper mines' from which natives had been reported to secure copper for tools, fishing spears, etc. After two successful attempts, he reached the Coppermine river in 1771, accompanied by Indian guides. This hazardous trip was indeed a remarkable feat when one considers the vast distance covered, a great deal of which was barren lands. At Bloody falls, (See Figure 1) on the Coppermine river, Hearne's Indians swooped down on a party of sleeping Esquimaux, who gathered there each summer to fish, and murdered the entire band encamped on that side of the river. Hence the name of the falls. Hearne's knowledge of minerals was undoubtedly limited. He reported having seen the copper mines from which the natives were securing the copper, but he failed to prove the economic possibilities of the copper occurrences or to give an accurate description of any deposit. Sir John Franklin visited the area in 1821. He and other members of his expedition, namely, Richardson, Back, Kendall, and Hood, reported native-copper float to occur in the vicinity of the Coppermine river and Bathurst inlet.

Jan 1, 1931

By J. B. Kitchin

"The design of conveyor belting for use in mines poses problems to the manufacturer that are unique. The challenge to be met is that of the production of a conveyor belt which can withstand use and misuse in an environment that may differ vastly from one country to another, and even between one mine and its neighbour.The development of a product to meet such varying requirements necessitates a protracted program of trials, both in the laboratory and in the field; a new successful development, the only criterion, can be said to have been achieved only after very long-term usage under actual, deliberately chosen, arduous mining conditions.New developments in conveyor belt construction can never stop, no more than can developments in new and advanced mining techniques. A new problem is set-an answer must be found. Some of the problems are noted here, and answered where possible, in what must after all be little more than an excursion into a very comprehensive and detailed subject."

Jan 1, 1967

By Edmund C. Bovey

"AS I begin my remarks this morning, please let me say how honoured and gratified I was to receive your invitation to address you here during your deliberations in historic Quebec City. The high esteem in which your Institute is held is reflected in the respect and deference accorded to it by industry across Canada. I feel privileged to be here with you today.I would like to discuss with you some applications of natural gas in the mining industry and suggest to you, in closing, some possible avenues of future development.Natural gas first became avail-able for industrial purposes in Northern Ontario in late 1958. Acceptance of natural gas, as a source of energy by the industry of that area, has been both widespread and gratifying. The mining industry of Northern Ontario has in-creased its annual use of natural gas by approximately 35 per cent each year since 1958. We believe that this trend will continue, al-though we will probably have to accept a more modest 10 per cent annual gain as the market approaches saturation. I would like to explain how we were able to do this and where all this gas is used. Our first sales were largely a matter of price-and the savings we offered were substantial."

Jan 1, 1966

By Hong-wei Ma

With social development and technological advancement, mine rescue robots used in complex environments have developed as a research hotspot. This paper reviews the progress of research on coal mine rescue robots, and key technologies of rescue robot design are put forward, such as mechanical structure, self-navigation and self-orientation, multi-sensor information fusion, multi-robot cooperation, and wireless communication technology.

Aug 1, 2013

By W. F. Baker

Location and History God's lake is in the northeastern part of Manitoba, about 400 miles northeast of Winnipeg, or about 250 miles due north of Red lake, Ontario. The lake is quite large, having an overall length of 54 miles and a maximum width of 18 miles. There are numerous islands in the lake, the largest of these, known as Elk island, being about 15 miles long and 3 miles wide in the widest part. The accompanying map (Figure 1) shows the location of God's lake and of the mine. The God's Lake area has long been regarded as promising country for the prospector, but, due to its inaccessibility, practically no prospecting was done prior to 1927. In the years 1927-1931, inclusive, a few prospectors visited the area, but no discoveries were made. In 1932, Bob Jowsey and Archie McDonald entered the area from Island lake. They first prospected in the vicinity of Knife lake, which is immediately south of the main part of God's lake, and then moved on to the latter lake, heading for the north shore of Elk island. The first afternoon on God's Lake, when looking for a place to camp on the north shore of what is now known as Jowsey island, Jowsey discovered a quartz porphyry dyke which was cut by a number of gold-bearing bluish quartz stringers. On the strength of this discovery, he and McDonald began at once to stake the Reno group of claims. Rumours of the discovery brought in other prospectors, and other groups of claims were staked to the east, along the north shore of Elk island. A second discovery was soon made by Dan McCrea on his Gold Standard claims, three and a half miles to the east of the original discovery. Staking still continued to the east, along the north shore of Elk island, and Bob Brown and Harvey McKenzie staked the Akers group on a discovery approximately two miles east of McCrea's discovery. Through the efforts of Jowsey, the Reno, Rand, Elk, and Cona groups, belonging to the original syndicate for which Jowsey and McDonald staked, were combined with the Gold Standard, Greenstone, and Akers groups, and the Company known as God's Lake Gold Mines, Limited, was formed. Several additional groups of claims were later taken over by the Company and a considerable area of adjoining ground was staked to round-out the property.

Jan 1, 1935

By Gaoming Wang

Outline 1. The Gangdese porphyry Cu-Mo belt 1.1 Regional geological background 1.2 Cu-Mo-bearing porphyries 1.3 Mineralization and alteration 2. Dating methods and results 2.1 Qulong porphyry 2.2 other porphyries 3. Geodynamic implications 4. Conclusions 5. Acknowledgements

May 1, 2004

By Gustavo Brunello

Motor Failure Rates and Cost ? Motor failure rate is estimated: 3-5% per year. ? In Mining, Pulp and Paper industry failure rate is up to 12%. ? Sometimes process downtime costs are higher than motor ?? Motor failures are due: Electrical 32% Mechanical 31% Environmental 36%

Feb 1, 2008

By D. J. Lucifora

Monitoring-While-Drilling (MWD) is a proven technique that records instantaneous on-drill parameters which can be used to supply contextual information for in-situ, down hole conditions, such as: changes in geology, the presence of pre-existing fractures and dynamic alterations, down hole conditions including bit bailing, bit blockages and bit wear, and improper drill operation. This technique has been widely used in the oil and gas industry and, eventually, it was transferred to the mining industry. A challenge when analyzing and interpreting MWD data is in utilizing proper filtering which enables one to properly eliminate any ?noise? from the signals of interest. Overall the importance of MWD data is that, through the collection of operational field-based data, a dataset can be acquired which allows experimentation and analysis to be carried out. Such a dataset is often impossible to replicate in a laboratory setting. If successful, and through iterative refinement, any promising method can eventually be implemented on-machine and using real-time monitoring techniques. This paper will provide a state of the art review of presently used MWD techniques and applications in industry. The paper?s primary focus will be on shallow, mining-style, blast hole drilling but will also take into account techniques and applications utilized in oil and gas drilling which have not been adopted in the mining industry. In the cases where MWD techniques and applications exist solely in oil and gas drilling the paper will examine and comment on the potential utility of technology transfer to mining applications.

Aug 1, 2013

By Pieter van Nierop

Outline ? What is gasification? ? Gasification Technologies ? Gasification ?The early years ? Gasification ? The last decade ? The Alberta Situation ? The Importance of Gasification in Alberta ? Polygeneration ? Development ? Conclusion

May 1, 2004

By J. B. Mitchell

Using digital image correlation the evolution of strain and strain at the onset of localisation resulting in a hot tear has been determined for alloys AA6111 and Al¬0.5wt% Cu during solidification. High resolution images of hot tear formation and growth were captured during a constrained bar test that incorporated a glass window above a central hot spot region. The images were analysed using digital image correlation software to measure the evolution of displacement and strain based on tracking the motion of discrete features on the as-cast surface of the sample. Temperature data was also acquired with a thermocouple cast into the sample in close proximity to the hot tear. The interval starting from the point immediately after solidification shrinkage ends (the metal pulls away from the glass) and finishing when the first sign of a crack or hot tear is visible to the eye was used to determine strain data. The minimum strain at which strain localisation occurs was found to be 0.0069 in AA6111 and 0.0021 for A1-0.5%Cu.

Jan 1, 2007

By P. J. Dunlop

THE object of this paper is to present a brief survey of the work done and the results obtained in controlling dust at the Hollinger Consolidated Gold Mines milling plant. The plant includes all primary and secondary crushing, grinding, and treatment operations. The major items of equipment are: (1) Underground Crusher Plant 1 48 in. by 60 in. jaw crusher, crushing run-of-mine ore to minus-6-in. Rate: 420 tons per hour (2) Surface Crusher Plant 3 No. 772 gyratory crushers 3 4 ft. by 16 ft. trommel screens 4 No. S gyratory crushers Reducing ore to rninus-172-in. Rate: 420 tons per hour (3) Roll Plant 5 sets of 62 in. bJ: 24 in. rolls 7 5 ft. by 10 ft. v1bratrng screens Delivering a minus-3/16-in. finished product Rate: 420 tons per hour (4) Grinding Plant 4 7 ft. by 15 ft. low discharge grate ball-mills 4 12 ft. reciprocating rake classifiers Rate: 4,800 tons per 24 hours Maximum capacity: S,800 tons per 24 hours

Jan 1, 1939

By A. Yousefpour, M. Hojjati, G. Chouinard

In recent years, high performance thermoplastic composites such as PEEK and PEKK have been developed for aerospace applications. These materials offer, among the other properties, high toughness and damage tolerances. These are semi-crystalline materials and their processing can lead to different crystallinity that in turn have some impact on the final properties. The effect of cooling rate on degree of crystallinity of PEEK is studied to identify the processing window for manufacturing. Samples were heated at the constant heating rate of 20°C/min up to 375°C (above melting point) and held for 10 minute. The enthalpy of the crystallization was measured at different constant cooling rates of 0.5, 1, 2, 5, 10, 20, 30, and 40°C/min. After cooling, the samples were heated at constant heating rate of 2°C/min using modulated DSC. At temperature between 90°C to 375°C, two endotherm peaks were observed. Results suggest that endotherm peaks are related to a melting and recrystallization phenomenon of one crystal morphology. However, the second endotherm peak could be associated with another crystal structure or morphology.

Jan 1, 2006

By Peter A. Witt

Highland Valley Copper is a conventional truck-shovel mining and flotation concentrator operation located some 75 kilometres southwest of Kamloops, B.C. (Figure 1). The ore is located within a porphyry copper deposit and is mined at a rate of 135,000 metric tonnes per day from two separate open pits. The nearby mill produces concentrates containing 375 million pounds of copper and 5 million pounds of molybdenum metal yearly. In the Valley pit, head grades are roughly 0.40% Cu at a 0.23% Cu equivalent cut-off. The Valley pit strip ratio currently sits at 0.55:1 with waste quantities made up of separate rock and unconsolidated overburden units. From the mill, concentrates are trucked to nearby Ashcroft and then hauled by rail to ocean port facilities in Vancouver. The mine employs 950 persons and is planned to operate until 2009. The operation is a partnership between TeckCominco with a 63.9% interest, BHP Billiton holding 33.6%, and others 2.5%. Management is shared by the two principal owners and directed by a management committee.

May 1, 2003

By M. C. Bluteau, G. P. Demopoulos

Arsenic reports in the effluents of many non-ferrous metallurgical operations. The production of scorodite, a crystalline ferric arsenate, is considered as an attractive option for the fixation of arsenic from aqueous effluents. However, scorodite solubility and long-term stability in the pH region of interest for tailings disposal have not been thoroughly investigated. In this study the long-term stability of scorodite in the pH 5 to 9 region and the mechanism of scorodite dissolution were studied. Construction of eh-pH diagrams indicated that scorodite stability is highly dependant on the nature (stability) of co-existing iron-hydroxide/oxyhydroxide. It was also found that when scorodite dissolves, a ferrihydrite phase having very small particles size (nano-scale) forms and that the growth and crystallization of this material are delayed by the presence of arsenate even under accelerated (75°C) ageing conditions. Around neutral pH and ambiant temperature (22°C) scorodite seems to reach an equilibrium with ferrihydrite after 48 weeks yielding soluble arsenic concentrations < 5 ppm.

Jan 1, 2004

By R. S. Forgan

The synthesis and study of a systematic series of phenolic oximes have shown that substitution in the 3-position can greatly affect extractive efficacy. Solid state, solution and gas phase analytical techniques, including X-ray crystallography, EPR and IR spectroscopy and collision induced dissociation mass spectrometry have been assessed for their applicability in interpreting the origins of differences in extractant strength. The dominant substituent effect on pH0.5 is the change in ligand pKa, with the more acidic ligands being stronger extractants. The influence of the 3-substituent on the stabilising intracomplex H-bonding of their copper(II) complexes also affects extractant strength. The 3-NO2 substituted ligand shows the lowest pH0.5 value, due to a combination of its low pKa and a stabilising bifurcated H-bond assembly around the copper(II) centre. Appending an aminomethyl group to the 3-position gives a ligand capable of binding a metal and its attendant anion. These metal salt reagents show potential to open up new flowsheets for the processing of high tenor copper feeds.

Jan 1, 2007

By Peter A. Witt

Highland Valley Copper is a conventional truck-shovel mining and flotation concentrator operation located some 75 kilometres southwest of Kamloops, B.C. (Figure 1). The ore is within a porphyry deposit and is mined at a rate of 135,000 metric tonnes per day from two separate open pits. The nearby mill produces concentrates containing 375 million pounds of copper and 5 million pounds of molybdenum metal yearly. Head grades are roughly 0.40% Cu at a 0.23% Cu equivalent cut-off. The strip ratio currently sits at 0.55:1 with waste quantities made up of separate rock and unconsolidated overburden units. From the mill, concentrates are trucked to nearby Ashcroft and then hauled by rail to ocean port facilities in Vancouver. The mine employs 950 persons and is planned to operate until 2009. The operation is a partnership between three owners: TeckCominco (61.4%), BHP Billiton (33.6%), and Highmont Mining (5%). Management is shared by the two principal owners and directed by an appointed committee.

May 1, 2002