Search Documents

By H. Henao, F. Canales

The present work evaluated the use of copper ore flotation tails as flux in the process of smelting copper concentrates. For this purpose, experimental and simulated liquidus lines were obtained at different ratios of tail/flux. Experimental variables included temperature, partial pressure of oxygen and sulfur dioxide and the conditions of tridymite or spinel saturation. The results indicate the feasibility of replacing the flux by increasing the temperature of the smelting process by 20°C. Results of simulation using FactSage and HSC confirm that the required increase in temperature can be achieved by increasing the flow of concentrate, enrichment of oxygen or increasing the matte grade. INTRODUCTION In the pyro-metallurgical process of copper production, the smelting stage produces two liquid phases, a sulphide phase rich in copper and another composed mainly of oxides called slag. The slag phase is the product of oxidation of the iron contained in the flotation concentrate. The smelting process which is carried out at temperatures of 1250°C, require the addition of silica as a flux and the injection of air enriched in oxygen (Schlesinger 2011). Currently, one of the most important aspects of the mining industry is the minimization of costs, the optimization of the use of available resources and the reduction of environmental impact. Under this context, the use of flotation tails from as a flux in the copper smelting process has the potential of reduced production costs and generate an environmental benefit by reduce the disposal amount of this waste material Regarding the use of copper tails as flux in the copper smelting process, a thermodynamic simulation study using the FactSage software had been reported in the literature (Parra et al., 2011). The results indicated an increase of 35°C in the temperature the liquidus for the equilibrium matte/spinel and a subsequent requirement of energy in the process of approximately 350 [MJ/ton slag]. Given that the calculated viscosity remains in the same order of magnitude, the melting temperature is a more relevant parameter for the evaluation of the use of tailings as flux.

Jan 1, 2019

By K. A. Hildebrant, J. R. Norgate

"Synthetic lubricants have for many years documented extended service life and provided superior performance in temperature extremes. Increasing interest in synthetics' ability to reduce energy costs has resulted in laboratory and industry application evaluations. These tests have documented savings in functions such as worm gear drives, spur gears and in compressors. Energy savings data are presented as well as payback calculations as low as thirty days.The National Research Council of Canada has estimated that the Canadian economy loses over five billion dollars per year in friction and wear. Figures quoted were for 1986 during which it was estimated that nine hundred and forty million dollars were lost in the mining industry alone"" It has been further estimated that about 115 million dollars can be immediately recovered through improved tribology practices (Table I).The purpose of this paper is to present results and savings opportunities through the use of synthetic lubricants in various but common applications. Many other areas exist with the opportunity for energy savings such as in the use of more efficient drive equipment, reduced contact seals, spray mist lubrication systems and reduced friction coatings on rotating equipment such as pump impellers"

Jan 1, 1994

By Mark B. Thorpe

Golden Star Resources started gold mining operations in Africa in 1999 after 15 years of exploration in South America. At the time, the approach to local assistance was through "alternative livelihood" programs and the donation of infrastructure to local communities. This was initially successful with local community support. However, with time and on reviewing the implemented projects, it became evident that the success was limited and many if the projects were either poorly used or in disrepair. Through a review of the options, we decided to develop a community assistance model driven by the communities themselves, while keeping control of the finances and the actual construction of the projects. Through the formation of the Golden Star Development Foundation, we began to support community driven projects for local economic development. The evolution of economic development projects continued over the next several years with the addition of project requirements for partnerships with government, and finally an evolution to a partnered turn-key piece of infrastructure that we hand over to an agency for operation and ongoing maintenance. We are currently working with outside partners to further our economic development activities in Ghana to the benefit of our stakeholders.

May 1, 2011

By C. Pichler, S. Luidold, C. Wagner, C. Sagadin, D. Kreuzer

Engineers and scientists have been combating the attack upon refractory materials of molten metals/matte and slags for hundreds of years. The details in many cases are still questionable or at least debatable. The corrosion is a major concern for furnace operators as refractory wear or failures inevitably results in reduced production efficiency and furnace reliability. Also the cost to industry is considerable and only a thorough understanding of all the complexities of the process will help to minimize that cost. One of the critical questions to overcome is the correct selection of refractories for the individual process steps to provide long and predictable refractory life together with high furnace availability. To understand the nature of the reactions involved in refractory corrosion, it is crucial to determine the complex thermo- chemical equilibria of the reactions occurring between the refractory materials and the process phases. A simulation model coupled with commercial software like FactSageTM is demonstrated aiming to understand the corrosion mechanisms between refractories and the molten process phases and draw implications for improving the performance of refractories and refractory lifetime. INTRODUCTION The extraction or recycling of valuable materials, e.g. metals, can be done by two main routes, pyro- and/or hydrometallurgical processing, depending on the chemical behavior of the used ore, scrap or pre-treated concentrate. Sometimes it is also necessary to use both process routes for the extraction or the recycling of valuable materials. In the case of a pyrometallurgical treatment, the usage of refractory materials is inevitable. This is mainly caused by high temperatures, prevailing during processing. The interaction between refractory material and slag, metal or matte leads to different reactions and interactions. As a main result corrosion of the furnace lining (refractory material) takes place. Hence, recurring furnace shutdowns occur for renewing the refractories. This leads to reduced production efficiency. Such refractory lifetimes are between some hours and decades, depending on the processes.

Jan 1, 2019

By François Charette

High stress conditions in underground mines push the performance envelope of support systems to their limit. In weak rock masses these conditions lead to large deformation and breakdown of the rock material, while stress release events in hard rock mines can lead to sudden and usually violent rock and support failure. In typical support systems, a combination of different reinforcement and support mechanisms provide the required convergence control and retainment. These systems usually involve a multi-pass support installation. The advantages of a single pass support system are investigated and several bolting combinations are compared. Criteria for design are reviewed and new criteria are proposed to include cost and effectiveness in commonly used engineering approaches. Field observation and testing is used to illustrate the difference between the proposed approach and more conventional systems.

Nov 1, 2011

By Eugene F. Mehr, Dennis C. Martin

"Development of the final slope for the 340 m (1200 ft) high hanging wall at Cassiar Mine precipitated an area of deep seated instability involving an estimated 17.6 million tonnes. The deformation mechanisms involved squeezing of soft deformable serpentinite rocks in the toe which caused planar sliding and graben toppling of the stronger sedimentary rocks in the middle and upper sections of the slope. Although movement rates up to 150mm/day were recorded, by understanding the controls on failure, the mine was able to install a suitable monitoring system and complete the open pit with only minor loss of the mineable ore. Accelerated mining was required in the last full year of operation. This paper describes the deformation behaviour, failure mechanisms and back analysis results for the failure. The monitoring systems and operational aspects related to the failure are also presented.IntroductionCassiar Mine is located in steep mountainous terrain in northern British Columbia approximately 1200 km north of Vancouver (Fig. I). During the final mining phase of the open pit, instability developed in the approximately 340 m high hanging wall (east wall) slope. A unique graben toppling mechanism was identified based on detailed assessment of slope monitoring data and visual observations. Comprehensive slope monitoring enabled mining to continue even though movement rates as high as 150 mm/day were being recorded. Three-dimensional limit equilibrium back analyses and numerical modelling have been used to assess the various controls on the slope movements and to understand the failure mechanism."

Jan 1, 1993

By Steve McMullan, Blaine Webster, Ian Johnson, Ron Matthews

"Time domain spectral Induced Polarization (IP) data from the Tower, Jojay and Laurel Lake gold deposits in northern Saskatchewan are presented. The resistivity data shows both resistivity lows (due to fault, shear or alteration zones) and resistivity highs (due to silicification) in the area of the deposits. The high resistivity zones suppress and distort coincident IP responses, calling f or high quality surveys and special care in interpreting the IP data.Electromagnetic methods are not effective in locating the deposits. This is due, in part, to masking by conductive cover. The Jojay Lake deposit has a strong magnetic response. A more indirect magnetic association is seen for the Tower Lake deposit. The Laurel Lake deposit has no magnetic signature. Magnetic data are useful in defining structure in all cases.All three deposits are outlined in the IP survey results. IP anomaly amplitudes from the pole-dipole array are from two times (Tower and Laurel Lak e) to six times (Jojay Lake) background values. Gradient array IP anomalies are of less amplitude. The spectral time constant is short for the Tower and Laurel Lak e deposits and long for the Jojay deposit. This implies that the metallic sulphides in the Jojay deposit are more interconnected than those of the other two deposits. INTRODUCTIONInduced polarization / resistivity surveys are commonly used in gold exploration program s in the Canadian shield because the IP method is effective in detecting disseminated metallic sulphides which are often found associated with gold. Other common geophysical sur vey methods such as magnetics, VLF and EM are not generally capable of direct detection of disseminated sulphides. Since the introduction of the IP method in the 1950s, it has undergone continuous improvement. The most recent improvement is the development of time domain receiver s which sample the full de cay and record it in digit al form. This results in a more complete measurement of the response which permits analysis and enhancement of data quality and the derivation of a nomaly parameters which characterize the measured decay. This extension of conventional time domain IP methods is called spectra l IP, a term first introduced by Pelton et al. working in the frequency domain Spectral IP surveys are attractive because they allow the possibility of discriminating between IP responses which have similar amplitudes but are due to dissimilar geo logic targets. The discrimination can be important in the selection of IP anomalies for follow-up.Time domain spectral IP survey results are presented over three known gold deposits in northern Saskatchewan-Tower Lake, Jojay Lake and Laurel Lake. The surveys were initiated and supported by Cameco-A Canadian Mining and Energy Corporation (formerly the Saskatchewan Mining and Development Corporation-SMDC) and were carried out by JVX Limited using the Scintrex IPR-II receiver and attendant spectral analysis software."

Jan 1, 1989

By Michel Ruel

Most plants do not track how their systems perform. Optimization is the easiest way to benefit from your control systems. We suggest an approach in four phases. The first phase is to assess all equipment to determine the performances for instruments, valves, variable speed drives, and other equipment. The second phase is to remediate instrumentation problems, including the ones pertaining to valves, variable speed drives, analyzers, transmitters. When equipment is in order, loops are put back in automatic mode. If a loop oscillates, use standard default values for this type of loop. The third phase consists in validating the control strategies, properly configuring the systems (control system, programs and parameters, HMI, alarms), and then tuning the loops and control strategies. The fourth phase consists in analyzing the process and expected performances in order to optimize the control loops and control strategies. If performance is not sufficient, a decision tree will be presented to determine the right approach: advanced regulatory control, model predictive control, or fuzzy logic control. Once all steps have been completed, control performance monitoring software is used to sustain the results and pinpoint equipment or loops not performing as stated. Alarm management and rationalization could also be performed after auditing the alarm system, if needed. Examples from plants will be used to demonstrate how this step-by-step method is applied and produces results. INTRODUCTION Maximizing what you already have is the best investment to remain competitive. This article aims to show the benefits of a systematic approach using modern tools to improve plant performance. We at BBA suggest dividing the work in four phases, and a subsequent phase can begin when the previous one has progressed: Assess, Remediate, Stabilize, Optimize, or add advanced control. This approach has been successfully applied to several sites. Examples and illustrations from these plants demonstrate how this step-by-step method is applied and produces results. Under the BBA method, there are four questions to answer before proceeding to the next step. For each control strategy, you should ask the following questions: Assessment: Does it work? Remediation: Do you use it? Stabilization: Is it stable? Optimization: Does it perform? Do you need advanced control?

Jan 1, 2019

By R. A. Parra, Fuentes, C. Godoy, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

In this paper, we report on the detection of spectral molecular emission of iron oxide (FeO) and copper oxide (CuxO) emitted by reactions occurring in a laboratory scale flash smelting process of pyrite (FeS2) as well as copper concentrate. The novelty of the technique is that, the molecular spectral emission sensing is achieved by using a low spectral resolution and low sensitive radiometer, enhanced with signal processing and matrix factorization techniques. The method was validated using a highly sensitive spectrometer, with a high spectral resolution; achieving a similar FeO spectral pattern as the one obtained after signal processing techniques over low resolution spectral signals. INTRODUCTION Visible-near infrared (VIS-NIR) spectroscopy is an optical contactless sensing technique commonly used to capture information about the emitted, absorbed, transmitted or scattered radiation in a physical or chemical process, with the presence or absence of an excitation light source such as a laser or a broad spectral band source. These techniques coupled with signal processing and machine learning algorithms, sometimes referred as chemometrics (Pisapia et al., 2018), can be found in processes such as: pharmaceutical (Kandpal et al., 2016); food (Coelho et al., 2016); combustion (Ballester & García-Armingol, 2010); siderurgy (Strakowski et al., 2014) industry, among others. In the extractive copper industry there are several technological developments using optical sensing techniques aimed to retrieve information about copper ore and concentrate mineralogical composition such as X-Ray Fluorescence, Qemscan® (Quantitative Evaluation of Minerals by Scanning Electron Microscopy) and X Ray Diffraction (XRD) analysis, however, because of the manual procedures to analyze the samples with these laboratory instrumentation, only discrete information during a daily based operation can be retrieved, making impossible for the operators to take decisions over the involved processes in real time. The aim of our research work presented here is to contribute with sensing and data analysis procedures based on VIS-NIR spectroscopy for the flash smelting process characterization, particularly in this paper, with the detection of FeO and CuxO molecular emissions in a laboratory scale setup.

Jan 1, 2019

By Daniel J. Corkery

Mines in Canada and the United States are subject to regulations limiting ammonia, nitrate and nitrite levels in mine effluents released into the environment. The primary source of these nitrogen compounds is typically explosive used in blasting operations, as ammonium nitrate (AN) remains a significant component of most explosives used in the mining industry. The amount of AN entering a local water drainage system is related to site conditions, explosives used, explosive handling and blast efficiency. Mining operators acknowledge AN loss to mine water from blasting operations. However, the mechanisms by which ammonia, nitrite and nitrate are entering the water drainage system, or the relative contribution of specific mechanisms, may not necessarily be assessed or monitored adequately. Characterization of these mechanisms, through systematic investigations, allows a mining operation to focus its efforts on reducing AN loss. This paper outlines a strategy for investigating the mechanisms through which AN enters the mine water drainage system and methods to mitigate this loss. This strategy includes collection and analysis of data to identify and quantify the AN loss mechanisms, design and implementation of tests to mitigate this loss, and assessment of the results. Such investigations are not intended to be a separate one-time project, but part of a long-term process of continual feedback and optimization that is related to the collection and reporting of AN levels for regulatory purposes. The implementation of the strategy must be tailored to each mine?s requirements and existing conditions.

Oct 1, 2010

By R. Prioul, J. Kear, D. Chuprakov, A. P. Bunger

"Hydraulic fracture (HF) growth through naturally fractured rocks challenges the development of accurate predictive HF models. The authors present laboratory experiments differentiating behaviours associated with orthogonal and oblique intersections between HFs and natural fractures (NFs). HFs were created in sandstone and crystalline (gabbro) rock specimens, impinging orthogonally or obliquely on an unbonded machined frictional interface. Ultrasound monitoring was used to observe the rate of propagation through the interface. A contrast was observed between direct and offset crossing for orthogonal and oblique intersection, respectively. The stresses required to promote crossing depended on the intersection angle between HFs and NFs.RÉSUMÉ La propagation des fractures hydrauliques (FH) dans les roches naturellement fracturées pose un défi pour le développement de modèles prédictifs. Nous présentons des essais en laboratoire qui différencient les comportements associés aux intersections orthogonales et obliques entre les FH et les fractures naturelles. Des FH ont été créées dans des spécimens de grès et de roches cristallines (gabbro), heurtés de manière orthogonale ou oblique sur une interface machinée, non liée, de frottement. Un suivi par ultrasons a servi à observer le taux de propagation à travers l’interface. Un contraste a été observé entre un croisement direct et un croisement indirect des intersections respectivement orthogonales et obliques. Les contraintes requises pour promouvoir le croisement variaient selon l’angle d’intersection entre les FH et les fractures naturelles."

Jan 1, 2016

By M. E. Stutt, R. H. Rehder

"The mining industry is taking advantage of the increased performance resulting from the use of variable speed A C drives for large motors. This technology provides increased efficiency under the variable speed and torque requirements of such drives as mine hoists, conveyors, and air moving equipment. The technology does introduce voltage spikes on the voltage wave form that stress the insulation system to a greater degree than would occur with a constant voltage source. These voltage spikes must be considered in the design of the insulation system used for these motors.BackgroundHistorically the insulation systems for large AC motors were designed to withstand with reasonable life the voltage stresses of a 60 Hz constant sinusoidal voltage. One of the design tests is a voltage endurance test that requires the application of a 60 Hz voltage from conductor to ground equal to four to five times normal and establishing a time to failure. These higher than normal voltages accelerate the normal aging process by causing extensive partial discharge activity (corona) within the insulation system and the time to failure is a relative indication of insulation life.In addition to the voltage endurance test at 60 Hz, the individual coils are subjected to a surge voltage test to establish the withstand capability of the turn to turn insulation under switching surge conditions. The surge voltage is a fast rise time, 0.2 microsecond to crest value, voltage spike that can be caused by a circuit breaker or contactor closing operation. These voltage spikes can have a crest value of greater than 3.5 times the normal line to ground crest voltage of the normal 60 Hz power supply. The standard withstand test value is thus 3.5 times normal line to ground voltage. Because the voltage surges or spikes occur mainly during start and stop switching conditions, voltage endurance under these conditions has not been a major factor in insulation system design."

Jan 1, 1995

By Gennaro Delisle

"Les Services TMG (Niobec) currently treat a niobium ore in the Chicoutimi area of Quebec. The mineral pyrochlore is present in a carbonatite deposit which assays 5% to 7% apatite.The ore is ground to minus 65 mesh and deslimed at 10 micrometres. Part of the carbonates are floated with a fatty acid emulsion and rejected to the tailings as a first step to ensure the proper conditions for the flotation of the pyrochlore concentrate. The carbonate concentrate is 65% minus 44 micrometres and is composed of dolomite, calcite, 22% apatite and a minor amount of silicates.A laboratory investigation was undertaken to determine the feasibility of extracting apatite from the carbonate concentrate. This led to the development of an economic flowsheet to produce high-grade apatite concentrate. The apatite is depressed with phosphoric acid, and the pH is adjusted at 4.8-5.0 with sulphuric acid. An additional amount of fatty acid is added to permit efficient flotation of the carbonates. 1n a second stage, the silicates left behind with the apatite concentrate can be removed by depressing the apatite with AIC3 while floating the silicates with a secondary amine.The results of the laboratory tests indicate the possibility of producing an apatite concentrate assaying 38.3% P2O5 (83.7% BPL) with a recovery of 66.2%. Pilot-plant tests undertaken at the concentrator yielded a concentrate of 34% P205 and recovery of 76%."

Jan 1, 1981

By M. Sommerfeld, U. Schwarz-Schampera, B. Friedrich, D. Friedmann

The steadily growing demand for metals and their price increase at metal exchanges make the mining and utilization of marine mineral resources like polymetallic nodules, manganese crusts or sulfide deposits in the near future a viable option to potentially increase the supply of base and precious metals. For a country with low potential to mine land-based resources like Germany, the industrial recovery of metals from marine mineral resources could lead to a decreased dependency on imports. In this study, seafloor massive sulfides from the German license area in the Indian Ocean (Kairei field, Southern Central Indian Ridge) are treated to recover copper and precious metals. The aim of the project is to demonstrate the transferability of existing metallurgical techniques to the raw material of deep-sea massive sulfides. As a starting point to process this unconventional resource, samples from the Indian Ocean are chemically analyzed and mineralogical characterized. A comparison is carried out between the samples and land-based copper resources, to highlight the potential which lies in mining the deep-sea floor. This paper will show the general possibility of applying a two-stage pyrometallurgical process, based on a concentrate smelting operation, followed by a converting operation in lab-scale to the provided samples of massive sulfides. Generated slag from the concentrate smelting and the converting operation are investigated by X-ray diffraction to determine the mineralogical composition. The two-stage pyrometallurgical process is investigated by the thermochemical modelling tool FactSageTM 7.2 to evaluate the phase distribution of relevant elements between the metal, matte, slag and gas phase. The thermochemical boundaries of the pyrometallurgical process are therefore set and the results of the thermochemical study can be used as an indicator for the efficiency of an up-scaled process and the generated amount of side-streams, which need to be further treated or circulated back into the process. INTRODUCTION Seafloor massive sulfides (SMS) are the third kind of discovered deep-sea minerals besides ferromanganese nodules and cobalt-rich ferromanganese crusts (Sharma, 2017). They occur in water depths around 250–4,000 m (Koschinsky et al., 2018). SMS are characterized by a high base metal and sulfide content. They were created by fluid circulation and hydrothermal convection over time (Han et al., 2018). Commonly, areas rich in SMS are associated with hydrothermal vent fields on the seafloor (Keith et al., 2018).

Jan 1, 2019

By J. Aiello

"A brief history of previous mining activity on Coal Mountain, near Corbin, British Columbia, is followed by a description of the steps leading up to the resumption of mining in /974 by Byron Creek Collieries. New developments, including a preparation plant, a rail spur and a totally enclosed facility, as well as operating techniques, are also discussed. IntroductionThe Corbin Mine of Byron Creek Collieries Limited is located in southeastern British Columbia, approximately 110 air miles southwest of Calgary (Fig. I), 15 miles south of Highway 3 via a newly constructed provincial road (Fig. 2). Development of the area began on July 30, 1905, when D.C. Corbin, a prominent businessman from the northwestern U.S., and his associate E.J . Robert s, first visited the site of Coal Mountain on horseback. Coal was in great demand by railways and other industrial users, so the Corbin Coal and Coke Co. , after acquiring 15,000 acres of land in the area , began to develop a mine.F.J. Roberts was responsible for the construction of the 14-mile rail spur, the Eastern British Columbia Railway, which joined the mine to the CPR main line at the McGillivray Loop. Rail access to the mine and its developing community, Corbin, B.C., was completed in September 1908, the same year that the first underground mine began production.The Corbin Coal and Coke Co. operated six mines on Coal Mountain (Fig. 3), and production from 1908 to 1930 inclusive totalled 2,337,800 tons. This production was allocated to the mines as shown in Table 1. No.3, 4 and 6 mines were operated intermittently from 1931 to 1935."

Jan 1, 1980

Real time analysis of ore quality between the mine and mill provides major benefits to copper mining and processing operations. Prompt gamma neutron activation analysis (PGNAA) is a proven technique that has been successfully applied for real time conveyed flow multi-elemental measurement. The advantage of PGNAA is that it measures through the full conveyed cross section continuously and provides representative element measurement without the need to constantly sample coarse (primary crushed) conveyed flows. High specification PGNAA analyzers enable accurate measurement over time increments as short as thirty seconds. Elements such as copper can be measured to a precision of 0.02% copper which is sufficient for high confidence in decisions for bulk flow diversion. Increments of eight tonnes are being diverted through a bulk ore sorting application to remove batches of waste from mill feed as well as divert material to different stockpiles based on ore quality. Longer measurement increments of two to five minutes are suitable for blending control of ores to reduce feed quality variability and to control average ore quality within a target range. Feed blends can be adjusted as frequently as required but typically multiple measurement increments are composited to produce a rolling average ore quality. The paper details two case studies where analyzers have been successfully used to measure conveyed flows for blending and bulk diversion applications. The real time measurements of ore composition are also used for ore reconciliation, in metal accounting and providing process operators with advance warning of ore quality changes that may affect grinding performance and cause process upsets. Real time ore quality measurement has proven beneficial in improving copper processing performance through better utilising plant capacity in a leaching operation, optimising ore feed quality, and reducing unnecessary processing of waste. INTRODUCTION Representative real time elemental analysis of conveyed ore quality using fully penetrative technologies has been available to the minerals industry since the 1990s. The Prompt Gamma Neutron Activation Analysis (PGNAA) technique was developed into a conveyed material analyser and soon adopted by the cement and coal industries which recognised the benefits in real time quality management. These commodities were ideally suited to this measurement technique as operations generally involved conveying bulk material prior to processing. Measured quality was used to divert material to different destinations or used to control blending for improved quality consistency. Uptake in the minerals industry, however, has been slow until the last ten years, and particularly until the mid-2010s.

Jan 1, 2019

By W. Díaz, R. A. Parra, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

This work presents visible-near infrared (VIS-NIR) spectroscopy measurements, and signal analytical techniques to characterize minerals and relevant pyrometallurgical process variables for the copper extractive industry. Data signal processing techniques such as baseline correction and numerical analysis are used to estimate the continuous and discontinuous spectral components. Such spectral components are used to estimate the process temperature, and patterns such as the integrated radiation. Also, metal combustion emissivity calculation are depicted. Our findings suggest that VIS-NIR spectroscopy may be a suitable technique to assess the process condition state, appearing as an interesting sensing alternative. INTRODUCTION Although the flash smelting process is one key stage in the copper extractive industry, representing about 40% of copper matte production worldwide (Cantallopts, 2017), few attention is dedicated to develop sensing solutions to assess process variables, such as mineralogical composition and temperature, in the feeding and bleeding stages, compared to the steel industry (Strakowski, et al., 2014). In this process and other industries, e.g. the thermoelectric power generation one, combustion and particularly the generated flame are the production chain’s heart. Since the flame is a highly radiative emitting process where chemical and physical transformations take place, many works had been dedicated to characterize the combustion state by sensing its radiation using optical and photonic technologies (Ballester & García-Armingol, 2010). In this context, this work aims to contribute with visible-near infrared (VIS-NIR) spectroscopy and pyrometry techniques to retrieve relevant information from a laboratory scale flash smelting process. On the other hand, since photonic instrumentation allow us to perform contactless measurements of emitted, absorbed, transmitted or scattered radiation, it appears as a suitable technique for sensing process properties in harsh environments, e.g. high temperature processes. One of these techniques is the Visible- Near Infrared (VIS-NIR) spectroscopy, which provides information about the spectral radiation intensity distribution, in this work, the emitted flame’s radiation. It is well known in combustion research that the spectral emission from a flame is composed by a black body continuous radiation background, molecular emissions, elemental emissions and additive noise features (Arias et al., 2011). To make sense of such information signal processing techniques are needed, here we propose to analyse the continuous and discontinuous spectral components separately.

Jan 1, 2019

By Michel Dagbert

"This paper illustrates the different ways grade-tonnage curves can be generated f or a mineral deposit. It emphasizes systematic discrepancies between reality, estimates and actual production according to different estimation methods and grade control programs. It does not offer a universal solution to the prediction of grade-tonnage curves. Hopefully, it will inspire caution to mineral economists who use estimated grade and tonnage data in the establishment of an optimum cut-off grade for a mining operation.IntroductionThe value of a mineral development venture often depends on a grade-tonnage curve. Statistics can help. The idea is to divide mentally the orebody into small blocks called selective mining units or SMUs. A SMU is an idealized version of the quantity of rock the grade of which will be tested against the cut-off at the time of mining. It could be as small as a truck load or a shovel load in very selective operations like some uranium mines where radiometric probing of each truck or car is performed. More typically, in an open pit operation, it will be the smallest zone flagged as ore from blast hole data, e.g. a 5 m by 5 m by 10m block, if blast holes are on a 5 m grid and bench height is 10m. Having defined the SMUs, the grade-tonnage curve determination amounts to evaluating the grade distribution of all the SMUs that can be mined in the depo sit. If we know this distribution we simply apply the cut-off to it and we get the number of SMUs above the cut-off (i.e. ore tonnage) and their average grade. .Assessment of the grade distribution of SMUs from exploration drill hole data is not an easy exercise and much has been published on the subject (David, 1972; Marechal , 1972; Huijbregts, 1975; Marechal, 1975; Guibal and Touffait, 1982). In this paper, we use a gold mine example to illustrate the influence of SMU size on the results. With the same example we also show that ""common-sense"" methods of grade-tonnage curve determination can sometimes be misleading."

Jan 1, 1987

By J. E. Lee

"This paper describes the current practices and experiences, and discusses design parameters concerning slurry pumping at Inco Metals Company in the Sudbury District. It deals mainly with the long tailing and concentrate lines. Subject matter is arranged under the following headings: pumps, lines, instrumentation, system design, operation.IntroductionThe Inco Metals Company is the mining and processing section of INCO LIMITED. In the Ontario Division, it operates 13 mines, 5 mills, a smelter, an iron ore plant and 3 refineries, all engaged in the mining and recovery of nickel and copper. This paper describes the slurry pumping practices in the mills of the Ontario Division.The PumpsWe have in our Sudbury area mills most of the available types of slurry pumps, in sizes from one inch up to twelve inches, a total of about 400 pumps. The rubber-lined, horizontal shaft pump is; most numerous. However, for certain applications, the hard-metal pump is essential, and is becoming more popular for general mill service. Two types of vertical shaft pumps are used. There are a few diaphragm pumps on small thickeners, but the larger thickeners have centrifugal pumps either directly connected to the under-flow or with one pump handling several gravity underflows. We have not used piston or plunger pumps in our mills."

Jan 1, 1978

By Ahmad Ghahremaninezhad, Noelene Ahern, Yeonuk Choi

Arsenic (As) is a toxic element and is a major contaminant in the extraction processes of some metals (e.g. gold and copper). Due to the toxicity of arsenic species, its removal from As-containing streams from extractive metallurgy processes and safe disposal is absolutely necessary. For nearly complete removal of waste arsenic species from metallurgical process streams, it is required to have arsenic in its pentavalent state (As5+ species). This study presents an oxidation process for arsenic species with air or oxygen gas as oxidant. Activated carbon (AC) or other carbon based materials are used to catalyse the oxidation reaction. Air or oxygen gas is the only consumed reagent which makes the economy of the process very attractive. The oxidation reaction can be carried out at ambient conditions (room temperature and atmospheric pressure) in less than 24 hours.

Jan 1, 2014