Search Documents

By Junhyun Choi, Allan Gomez-Flores, Chonbuk National University, Siyoung Q. Choi, Gahee Kim, Seungkon Kim

In this study, to confirm the effect of depletion attraction on the flotation, we theoretically and experimentally investigate the effect of the depletion attraction force on flotation. While varying the concentration of the depletion agent (polyethylene glycol), three different systems are studied: pure malachite, pure silica, and a 1:1 mass ratio of malachite and silica binary system. We find that recovery increases significantly as the concentration of the depletion agents increases for all three systems, as the depletion agent facilitates the adsorption of the particle on the bubble surface. However, the recovery suddenly decreases in a certain concentration range, which corresponds to the onset of the decreased surface tension when high concentrations of the depletion agent are used. This non-monotonic overall recovery trend implies the surface adsorption of the depletant on a surface. The decreased surface tension of the air/water interface suggests that the recovery rate is lowered due to the adsorption of the depletion agent to the bubble surface, acting as a polymer brush. Based on our observations, we conclude that the depletion force can greatly improve particle adsorption, as predicted in the accompanying theory paper, while simultaneously the adsorption of the depletion agent on the bubble surface plays an important role because it hinders particle adsorption. We also perform experiments in the presence of a small amount of a collector, sodium oleate. An extremely small amount of the collector leads to the increase in the overall recovery, which eventually reaches nearly 100 percent. Nevertheless, the grade worsens as the depletant provides the force to silica particles as well as target malachite particles.

Jan 1, 2016

By Abu Syed H. Kabir, Mehdi Sanjari, Steve Yue, Jing Su, In-ho Jung

AZ31 magnesium alloy sheets were produced by high speed rolling (HSR) at 1000 m/min at a low temperature of 100 ?. A high reduction of 72% can be achieved in single pass. At the reduction of 30%, the microstructure was covered by shear bands and twins. When the reduction was increased to 49%, dynamic recrystallization (DRX) was clearly observed in the vicinity of shear bands and twins and the full recrystallization was seen at a reduction of 72%. In order to study the static recrystallization (SRX) behavior on the heavily twinned structure, annealing was then carried out at 200 ? on the as-rolled specimens at the reduction of 30% for different times. Static recrystallized grains were also firstly observed on shear bands and twins after 45 s and the microstructure was mostly fully recrystallized after 1 h annealing with a few retained large elongated un-recrystallized grains. Texture weakening was found during annealing on the heavily twinned specimens by SRX, but not during high speed rolling by DRX. In the present study, effect of DRX and SRX on microstructure and texture evolutions during rolling and annealing were compared.

Jan 1, 2015

By J. A. Brusset

Introduction The West Canadian Collieries, Limited, operate three bituminous coal mines in the Crowsnest Pass district of Alberta. Two seams are worked; their thickness varies from 10 to 20 feet and their pitch from 10 to 45 degrees. The Bellevue mine was opened in 1903, the Greenhill in 1914; both are gassy and dusty, and at both the haulage is a problem, as the workings are spread over distances of several miles. Compressed-air locomotives are used at Bellevue, rope-haulage at Greenhill, both of which solutions of the haulage problem are costly in installation an operation, and lack flexibility. In 1943, the Adanac mine was opened; and the question soon arose as to which system of haulage should be selected. Compressed-air locomotives and ropes were rejected on the ground of high cost. Since, under the Alberta Mines Act, the use of trolley locomotives underground in coal-seams is not permitted, the choice lay between storage battery locomotives and Diesel locomotives. The preference of the author, who had had experience with both in French gassy coal mines prior to 1930, was for Diesel locomotives, due to lower cost of installation and greater flexibility and reliability. However, Regulation No. 13 of the Mines Act of Alberta reads: 'No gasoline-driven engines shall be used underground in any mine, and no internal combustion engine shall be used underground in any coal mine, except only when authorized by the Chief Inspector in writing, and on such terms as he may prescribe"

Jan 1, 1948

By W C. Shakespeare

The Ontario Committee on Taxation is making a comprehensive study of taxation in the Province of Ontario, and in this connection has received representations concerning mining taxation from a number of interested parties. Some of the more important recommendations on mining taxation are reviewed in this article. Introduction FOLLOWING the appointment of the Federal Royal Commission on Taxation, the Ontario Government, effective in November, 1962, appointed the Ontario Committee on Taxation to review taxes and revenues available to the Province of Ontario and its local governments, to co-operate with the Royal Commission on Taxation and with any other bodies of enquiry appointed by other provincial governments, and to make such recommendations as it sees fit to the Prime Minister of Ontario and the Executive Council. The members of the Committee are: MR. L. J. SMITH, F.C.A., Toronto, (Chairman) MR. ERIC HARDY, Toronto DR. R. CRAIG MCIVOR, F.R.S.C., Hamilton MR. CARL A. POLLOCK, Kitchener MR. R. BREDIN STAPELLS, Q.C., and Toronto. Like its Federal counterpart, the Royal Commission on Taxation, the Ontario Committee has held public hearings, has received written

Jan 1, 1965

By D. W. Zandee

"IntroductionHaving mined an economic mineral bearing rock which is of insufficient grade to warrant direct smelting, upgrading or beneficiation is required to make it an economically viable ore. The first step in effecting the concentration process is comminution or sequential breaking of the rock to allow liberation and subsequent recovery of the desired mineral particles. Desirably the ore could be broken down to the point where the valuable mineral is completely liberated to maximize the chance of recovering as much of it and in as pure a form as possible. The number of energy intensive stages of breakage required to attain this goal depends on many physical characteristics of the ore such as hardness, friability, toughness, grain size, existing fracture planes and particle shapes.Commonly the distinct stages are primary, secondary and often tertiary crushing and finally grinding. To increase the efficiency of each stage of size reduction, pre-treatment sizing is common.Crusher feed is commonly scalped of large pieces or screened for reduction crushers and classified for secondary grindingcircuits.Although crushing and screening is employed for many different products, this chapter reviews current practice in larger tonnage metalliferous ore treatment plants.Current practice is to use large gyratory or jaw crushers for primary crushing and some sort of gyrating or cone crushers for additional stages of reduction. For autogenous or semiautogenous grinding circuits only the primary crushing stage is necessary, the balance of the work being performed in the grinding stage. For conventional grinding circuits using ball mills or combinations of rod and ball mills, secondary, tertiary and even quaternary crushing stages are normally required.Older type crushers such as stamp mills, double rolls, sledging mills and hammermills are no longer common but are used for small tonnage special processes.Important to efficient crushing are a variety of sizing devices such as grizzlies and vibrating screens. Products at different stages must be stored to give surge capacity and allow controlled feeding rates through mechanical and gravity feeders. These storage piles, bins and feeders as well as crushers and screens are commonly integrated into a total facility by means of conveyor systems. Most often these are endless rubber belts driven by simple or multiple drive mechanisms usually consisting of electric motors and speed reducers."

Jan 1, 1989

By JOHN H. HUDSON

Ceramic clays of the Prairie Provinces range in age from Lower Cretaceous to Pleistocene and Recent. Two significant ceramic clay horizons are the Paleocene Willo wbunch Member of the Ravenscrag Formation in Southern Saskatchewan and the Upper Cretaceous Whitemud Formation, which is found in Saskatchewan and Alberta. The Willowbunch Member is worked at one locale in Saskatchewan; the Whitemud Formation is worked at several locales in Saskatchewan and Alberta. Bentonite operations are found at Morden in Manitoba, Rosalind and Onoway in Alberta, and Wilcox in Saskatchewan.

Jan 1, 1984

By M. B. Kime, A. T. Kaniki

"Grinding tests were conducted on an oxidized copper-cobalt ore using a pear-shaped ball mill. Twelve mono-sized ore fractions were prepared and wet ground batchwise. The mill was run for 0.5 to 30 min intervals. The shortest interval provided data more closely related to the breakage function (B) because less secondary breakage was hypothesized. Some selection function (S) and B parameters were determined. Remaining parameters were estimated using a population balance model simulator. To evaluate the kinetics model, an unsized ore sample was also milled. Predicted and measured particle size distributions (PSDs) agreed well, suggesting that S and B parameters can be used for continuous operation mass balances.RÉSUMÉ Des essais de broyage ont été menés sur un minerai oxydé de cuivre-cobalt à l’aide d’un broyeur à boulets piriforme. Douze fractions de minerai de dimension unique ont été préparés et broyés en voie humide en lots. Le broyeur était mis en route à des intervalles de 0,5 à 30 minutes. L’intervalle le plus court fournissait des données plus étroitement liées à la fonction d’abattage (B) car d’après l’hypothèse avancée, le besoin d’abattage secondaire était moindre. Certains paramètres de la fonction de sélection (S) et de B ont été déterminés ; les paramètres restants ont été estimés à l’aide d’un simulateur de modèle d’équilibre de population. Pour évaluer le modèle de cinétique, un échantillon de minerai non calibré a également été broyé. Les compositions granulométriques (PSD, de l’anglais particle size distributions) prévues et mesurées correspondaient bien, ce qui laisse penser que l’on peut se servir des paramètres S et B dans le cadre d’équilibrages massiques en fonctionnement continu. INTRODUCTIONSize reduction of solids is a very energy intensive and highly inefficient process. It consumes approximately 5% of the electricity produced worldwide (Rhodes, 1998), and more than 50% of the total energy used in mineral processing plants (Walkiewicz, Lindroth, & Clark, 1996). An increase in grinding efficiency can therefore result in significant reductions in operating costs. This often amounts to determining the optimal design configurations for milling an ore sample in a laboratory mill under standard conditions. Prior to optimizing the milling stage, the requirements for downstream processing in terms of particle size distribution (PSD) need to be understood because low liberation and overgrinding will lead to future problems. Once this is done, it is also important to clearly understand the breakage properties of the ore. The kinetics of size reduction in tumbling mills are often determined using two probabilistic functions: selection and breakage (Austin & Luckie, 1972). Knowledge of the selection and breakage functions also enables the prediction of the PSD for a given ore sample."

Jan 1, 2017

By Pierre Buteau

Peat/ands distribution in Canada is widely spread thoughout the country and corresponds to a wide spectrum of wetland habitats which overlay peat deposits. The development and the evolution ofpeat/ands and peat deposits are closely linked together, since the vegetal remains of the peat deposits originate from the peatland habitats, and the peatland habitats constitute a response to many factors, including the properties of the substrate, which are the peat deposits. Peat/ands are defined as waterlogged terrains where the production of plant materials usually exceeds the rate of decomposition. The underlying peat deposits consists of organic residues associated to peatland vegetation, more or less decomposed, built up and kept under anaerobic conditions. Peat/ands evolution and distribution are determined primarily by climatic factors, but also by the geomorphology and edaphic conditions. All of these create particular hydrodynamical environments which will vary according to different regional settings, and sequentially to an evolutive time frame.

Jan 1, 2001

By D. G. Klaren, E. F. de Boer

Self-cleaning fluidized bed heat exchangers have demonstrated unparalleled performance internationally for the implementation of indirect heat transfer in severely fouling fluid environments. The ingenious configuration of recirculated cleaning particles through the tubes of vertical shell and tube heat exchangers provides the ability to solve any problems that arise as a consequence of tube-side fouling during indirect heat transfer to process fluids or slurries. In most cases, the cleaning particles consist of chopped metal wire, however other process-specific materials have been used. In addition to the mitigation of fouling effects, a number of other significant benefits for slurry heating are afforded by the mode of operation of the self-cleaning fluidized bed heat exchangers. Increased turbulence at the slurry/tube interface is imparted by the action of the fluidised particles, resulting in very high heat transfers at relatively low liquid velocities. Furthermore, given the thixotropic nature of most process slurries, the action of the fluidised particles imparts additional shear to the process slurry, resulting in shear thinning effects with a consequent reduction in pressure drop and enhancement of heat transfer across the heat exchanger. The benefits provided by the self-cleaning fluidized bed heat exchanger make it the ideal option for the indirect heating of laterite nickel slurry for High-Pressure-Acid-Leach (HPAL) plants. This article explains the principle and application of the self-cleaning fluidized bed heat exchanger technology for the processing of laterite nickel and cobalt slurries in HPAL plants. It also presents an elegant method to revamp existing direct heated laterite nickel and cobalt processing plants into an indirect heated configuration employing self-cleaning fluidized bed heat exchangers.

Jan 1, 2004

By Tanai Marin

Modelling of pyrometallurgical processes can become extremely challenging when the process involves complex chemical reactions, phase change, multiphase flows, heat and mass transfer and fluid flow. Traditionally modelling involving complex thermodynamic equilibrium and thermochemistry are treated separately from problems in which transport phenomena are dominant, such as CFD and heat transfer studies. The separation is also necessary due to the lack of modelling tools that can effectively couple both solution thermodynamic and transport phenomena or even multiphysics problems. However, there are, quite often, problems in high temperature process metallurgy in which it is not possible to simplify this two modelling approaches. Typical cases of this are for example, the modelling of slag freezing on furnace walls (electric or flash furnaces) to create a protective layer in front of the refractories hot wall, the formation of build up from the matte or metal phases at the hearth of the furnace, calcine smelting from charging piles into slag phase, etc. The problem is even more challenging in nonferrous pyrometallurgy as most, if not all, of the condense phases are highly non ideal solutions involving several components and exhibiting complex crystallization paths and miscibility gaps, such as the Fe-Ni-Cu-S matte, FeO-Fe2O3-SiO2, FeO-MgO-SiO2 slags, etc. In this paper, an approach to model coupled problems involving multiphysics and solution thermodynamic is presented. The approach consists in developing in-house a library containing the Gibbs energy minimization routines and using the local equilibrium concept for process modelling from a multiphysics commercial software (COMSOL). Simple test cases, such as building a non-ideal binary phase diagram on a CFD package is presented, the limitations and of other classic approaches such as equilibrium or Scheil cooling are discussed and compared to this model.

Jan 1, 2015

By Fazel G. Jahromi, Ahmad Ghahremaninezhad

Enargite (Cu3AsS4) is a major complex copper mineral and often is a carrier of invisible gold particles. Pyrometallurgical treatment of enargite is challenging due to the arsenic release to the environment. Hydrometallurgical treatment, on the other hand, appears to be a promising alternative for enargite processing. In an atmospheric enargite leaching process both the copper and arsenic from the mineral can be leached into a sulphuric acid solution and the arsenic can be simultaneously precipitated as ferric arsenate. The unlocked gold in the residue then can be recovered in a subsequent cyanidation circuit. The downside of the atmospheric enargite leaching in sulphate solutions is the slow leaching kinetics. In this study the effective parameters of the atmospheric enargite leaching process in ferric chloride media were investigated. All the experiments were carried out at temperatures below 100 °C. The process parameters that were investigated in this study included ferric, chloride, sulphate and cuprous concentrations, temperature, mixing rate and leaching slurry pulp density. It was found that the copper recovery rate increases with the addition of cupric chloride and also with raising the temperature. The highest leaching kinetics and the highest overall copper recoveries were achieved when cupric was initially added to the leach solution and at 90 ºC.

Jan 1, 2015

By A. V. Corlett

THE use of the diamond-drill hole as a means of breaking clown ore and waste is not new. Years ago, the method was adopted in mines in northern Ontario and in the western United States to reach out to bad pillars, or to remnants of ore left on walls, the winning of which by any other method might be dangerous or too expensive. The practice is still in vogue and has generally proved a success. Of the known mineral deposits in Canada and elsewhere, many are of very low grade. Some are marginal and not even worthy of being classed as 'ore' until some means is found and proved of exploiting them economically. Other conditions being favourable, if a mining method could be found that would give a large 'bulk break' with a sufficiently low cost of development and a low cast of mining per ton, mineral deposits of this latter type might be brought into the classification of ore. We know that any block-craving system whereby the ore may be undercut and allowed to crush and cave will give a very high breakage and low costs. In some cases, however, the physical characteristics of the ore do not lend themselves to this method. In such ore-bodies, the alternative system of 'bulk-breaking' might be aided by long diamond-drill blast holes. We could obtain this 'bulk breaking' by the use of long diamond-drill holes in conjunction with a sub-level system using extremely thick benches, or possibly by the adaption of modified open-pit methods to underground mining. ln fact, if conditions are favourable, the idea would be simply ta open up a slot or free face and break into it on a larger scale with longer holes. The use of deeper benches-that is, using each level as a sub-level and thereby eliminating much development footage, slashing, setting up, and mucking time-would naturally be expected to lead to cheaper mining.

Jan 1, 1940

By H. L. Ramandi, P. Moore

"The corrosion of support bolts in underground mines has become an increasingly prevalent issue over the past two decades. With an increase of premature failures due to Stress Corrosion Cracking (SCC), it is evident that understanding the environmental factor influencing the cable bolt corrosion is critical for maintaining effective ground support hence the safety and productivity of underground spaces. Experimental testing of rock and cable bolts were accomplished in a variety of packings, including saturated clay, saturated coal, mine water and grout/cement to investigate their corrosion behaviours. Water samples were obtained and analysed for pH and electrical conductivity (EC) during the experiment. After a period of 76 days the bolts were retrieved and analysed visually. Primary factors were found to be the presence of geological materials and the aeration of the bolts, i.e. the vicinity to air and air flow, while secondary factors were observed to be pH levels and EC. It was also found that the coal/clay interfaces and the water/grout/cement interfaces are non-relevant to corrosion of rockbolts and cable bolts. The proposed framework can be applied to other reinforcement materials used in underground spaces for improved understanding of corrosion environment.INTRODUCTION Rock bolts and cable bolts are the major reinforcement elements used in mining industry to improve the rockmass properties for safe and productive mining. They are normally used to pin large beams or blocks of rock in underground mines to stabilise the rockmass in the roof (strata) against collapse. The rockbolts are typically low cost hot rolled rebar while cable bolts are composed of strands of wire, normally wound together around a central king wire (Hyett and Bawden, 1993; Vandermaat, 2014). The typical length of the bolts in underground mines is 2.4 m and 4–12 m for rockbolts and cable bolts, respectively (Vandermaat, 2014; Windsor and Thompson, 1997). Cable bolts are much more flexible and usually offer a much higher load capacity than rigid rockbolts. Their increased length and flexibility allows cable bolts longer than the height of a roadway to be used in underground mines."

Jan 1, 2017

By M. I. Abbas, M. A. Shahin, M. S. Ahmed

"The influence of annealing of galvanized steel (galvannealing) on its corrosion kinetics in a saturated solution of Ca (OH)2 has been studied by means of the polarization resistance method.Galvannealing heat treatment was carried out at 450°C and 550°C for varying times. Annealing at 450°C for 24 hr or at 550°C for 5 hr showed the highest corrosion potential (Ecorr) ~= - 400 m V/ SCE as well as, the lowest corrosion current density (icorr ~= 3 mA.cm-2, while Ecorr and icorr of the unheated specimens were ~= - 1400m V/SCE and == 20 mA.cm-2, respectively.Polarization curves were also obtained for the as-received galvanized specimens together with the galvannealed ones.INTRODUCTIONHeat treatment of galvanized steel (i.e . galvannealing) is carried out at a temperature range of 450°C to 550°C for a time sufficient to convert the free zinc coating to an alloyed one consisting of layers of iron-zinc intermetallic compounds. Table I is a review of the properties of the Fe-Zn intermetallicphases while Figure I is a reproduction - of the Fe-Zn equilibrium phase diagram taken from Hansen.Several authors have studied the formation of intermetallic phases through the interdiffusion of Zn/Fe couples. Their results confirmed the stability of intermetallic phases that could be shown up on the outer surface as a result of galvannealing of galvanized steel.Bernick and Sievertv"" investigated the processing of galvan nealed steel. They found that the galvannealed coating with the best forming qualities consisted of a mixture of Zeta phase and Eta phase."

Jan 1, 1989

By Jack Craft

Local Environment Atmospheric conditions (or lack thereof) Drilling fluids are impractical Cuttings removal is a major concern Heat dissipation is a major concern Some tried-and-true mechanisms need air to function properly Gravity Low gravity means low downforce Microgravity means even less downforce Regolith Local dust may be highly abrasive Packaging for Spaceflight System mass is highly constrained The drill must fit within the spacecraft?s launch envelope Power is constrained

May 1, 2013

By K. L. Ford, D. R. Lentz, J. H. Rickard, R. P. Taylor

Abstract - Coupled gamma-ray spectrometric and lithogeochemical studies throughout the Heath Steele Mines area, Bathurst Camp, New Brunswick, indicate that primary and secondary geochemical differences exist between the stratigraphic footwall and hangingwall crystal tuff units which host the massive sulfide deposits. Of particular interest is Th, and to a lesser extent, Zr and Y, which are more concentrated in the hangingwall than the footwall crystal tuffs, whereas the opposite is true for TiO2. This expands on earlier lithogeochemical-chemostratigraphic results concentrated in the eastern part of the Heath Steele belt that led to revision of the local stratigraphy, and necessitated a structural re-interpretation of the area with implications for exploration. Although K depletion (decreased K and K/Th) is typical of chloritized footwall zones of chloritization, these features were not fully apparent here due to the recessive nature of these altered zones. In situ radiometric analysis using a portable gamma-ray spectrometer is a rapid, inexpensive analytical technique for chemostratigraphic characterization of rock units within volcanogenic massive sulfide deposit settings, provided there is a contrast in the distribution of natural radioelements, particularly Th and K.

Jan 1, 1998

By K. Chattopadhyay

Fluid flows in metallurgical reactors play a vital role on liquid metal cleanliness for both ferrous and non-ferrous metallurgy. Thus, it is absolutely critical to understand different fluid flow mechanisms, and the use of computational methods to model the complex non-isothermal, turbulent, single- and multiphase-flows, has to be appreciated. The present case study emphasizes on controlling the flow of liquid steel in a tundish and enhancing liquid metal cleanliness. CFD modeling was used to build a robust mathematical model, and effects of flow control furniture and non-isothermal conditions were analyzed. The mathematical model was validated against water model experiments. Parameters that were conducive for inclusion removal were identified and implemented in the plant. Some flow control devices could increase inclusion removal to a great extent compared to the existing configurations. In cases, where a hot ladle was poured into a relatively cooler tundish, inclusion removal was better, whereas results were catastrophic in cases where colder liquid was poured from ladle to the tundish. Similar techniques can be applied for other liquid metals including light metals and non-ferrous metals.

Jan 1, 2015

By A. Roy, T. LeBel, P. Coursol, P. Lind

At the early stage of a mining project, small amounts of concentrates are available for testwork. For gold concentrate or ores containing significant arsenic levels, batch bench scale roasting is often unreliable, leading to highly variable gold recoveries to be used in the project’s financial justifications. With an appropriate bench scale unit using continuous feeding and residence time control for solid and gas phases, reliable numbers can be obtained at small scale with only a few hundred grams per test condition. This paper describes the development of a pilot fluid bed roasting unit by Kingston Process Metallurgy Inc. (KPM) to perform representative trials on gold concentrates containing arsenopyrite, arsenian pyrite and carbonaceous components. Calcines produced under different conditions were characterised by chemical analysis and electron microprobe; the calcine microstructure obtained is described. The most important parameter affecting gold recovery is oxygen content in the roasting atmosphere, with the lowest controlled oxygen level giving the highest gold recoveries. Higher local temperatures in the bed may cause the formation of molten glassy phases which can also reduce the gold recoveries significantly. The impact of roasting conditions in the two inch fluid bed is compared with commercial results obtained in full scale operation.

Jan 1, 2014

By B. Hohenstein, B. McBain, B. de Jong

"The automated fire assay system (Fast In-line Fire Assay or FIFA) has not found acceptance in the Au mining industry as the lower measurable limit of 0.20 ppm did not allow Au tailings to be measured with confidence. The development of arrested cupellation has overcome this hurdle which was a limiting factor in the FIFA 1 process. In the new automated fire assay process, automated sample preparation, fluxing, fusion and separation of a Pb button are essentially similar to the FIFA 1 process, albeit with some improvements. However, the game-changer is the development and incorporation of arrested cupellation into the automated system, now called FIFA 2. The purpose of arrested cupellation is to reduce the 50 g Pb button to a 5 g Pb button by partial cupellation in a specially developed arrested cupellation system thereby concentrating the Au in the Pb by a factor of 10 and in so doing moving them into higher concentration ranges in the mini-button where they can be read on the spark spectrometer. Results show that concentrations down to 0.02 ppm Au in geological materials can now be determined using arrested cupellation in the FIFA 2 process, an order of magnitude improvement over FIFA 1.INTRODUCTION Traditional fire assay for Au has remained virtually unchanged for 3000 years. It has survived for so long because it is accurate, has relatively low detection limits and is relatively inexpensive. However, it is labour intensive, has a long turn-around time (typically at least 7 hours), is environmentally unfriendly and exposes assay operators to potentially unsafe conditions (toxic fumes, toxic dust and extreme heat from furnaces). The NiS collection method is not as effective for the assay of Au as it is for the PGEs. A rapid, accurate, cost-effective method for the determination of Au and the Platinum Group Elements (PGEs) in geological materials would be a tremendous benefit to mining companies. Many of these objectives have been met by the FIFA 1 (Fast In-line Fire Assay) developed some 15 years ago in which automated methods have replaced the manual procedures which are part and parcel of conventional fire assay. However, concentrations below 0.2 ppm have been very difficult to achieve with sufficient reliability."

Jan 1, 2017

By E. Haccuria

Due to the growing share of electrical cars, the use of lithium ion batteries significantly increased. Recycling of these batteries is essential to safely dispose hazardous materials as well as to recover valuables (Cu, Ni, Co, etc.). In order to optimise the recycling process, accurate information is required on the slag phase equilibria for battery smelting. The slag is a multi-component system containing alumina from the battery cases, silica and lime from fluxes, and manganese and lithium from the electrode materials. The present study accurately determined the phase equilibria in the "MnO"-Al2O3-SiO2 sub-ternary system at metal alloy saturation. Particular attention was given to the accuracy and reliability of the final results by highlighting the different reaction pathways, mass transfer- and reaction mechanisms taking place in the system during experiments. This attention enabled improved experimental methodology and measurements. Based on the present study, further measurements will be undertaken in the quaternary "MnO"-Al2O3-CaO-SiO2 system at low "MnO" concentrations, which closely represents the future recycling industrial slags.

Jan 1, 2014