Search Documents

Severe development difficulties were experienced soon after in-seam mining commenced at Appin Colliery in'1962. Thirteen years later no significant pro- gress had been made in overcoming some aspects of this development problem. Some success had been achieved in destressing roadways both in development and pillar extraction. Longwall retreat mining had shown promise of being highly productive but at an extremely high cost in terms of development requirements both in number of roadways and intensity of support in those roadways. No real advance was made in the problem of driving the first heading of a group of headings under conditions of apparently high stress in directions other than the preferred mining directions, although failure of the roof in this heading did seem to give easier work in the subsequent headings driven particularly if they were driven on narrow centres.

Jan 1, 1976

By S Pfaff, R Rajic

In the case when the number of independent variables is greater, a careful design for carrying out tests has to be made in order to obtain, with the smallest possible number of tests, as much as possible neutral information about the influence of independent variables on the dependent ones. Only on the basis of such design and its statistical analysis it is possible to come to right conclusions about the function of the whole system. The influence of pressure, temperature, humidity and granulation of the coal upon the resistance to pressure and the water absorption of the briquettes has been tested, with the aim to examine how each of the two dependent variables changes depending on the values assumed by any of the four independent variables and which of the mentioned independent variables significantly influences the dependent ones. The full factorial design with 16 experiments and the central composite design with 27 experiments have been applied. The influence of the independent variables upon the dependent ones has been examined by applying the analysis of variance. The influence values of individual factors and their interaction upon the dependent variables have been stated as well as coefficients of curvilinear equation.

Jan 1, 2003

By J J. Cilliers, K Hadler

The potential of air rate profiling to significantly improve the flotation performance of a bank of cells has been shown by numerous studies. To date many profiles have been evaluated; balanced, increasing, decreasing and combinations of these. An increasing air rate profile, where the air rates are increased proportionally to each cell down the bank, has been typically found to yield improved flotation performance compared to other profiles. Air rate profiling has two distinct components; determining the correct total air rate for the bank, and determining the correct distribution of that air. This can be done simultaneously by finding the optimal air rate to each cell in the bank in turn through air recovery optimisation. Air recovery is the fraction of the inlet air which overflows the weir of a cell as unburst bubbles. The peak in air recovery (PAR) is a robust measurement of optimal performance for the operating conditions in the cell, and sets the PAR air rate. In this study, plant trials of different air rate profiles and profiling based on PAR, were evaluated. The total air rates to the bank for all profiles tested were approximately equal, allowing direct comparison. The highest cumulative mineral recovery was achieved by operating at the PAR air rates for each cell down the bank. Different distributions of the same total air rate to the bank gave the same cumulative upgrade ratio, but lower cumulative recoveries. In this work the upgrade ratio is defined as the ratio of the concentrate grade to the feed grade. The increase in cumulative mineral recovery, at the same upgrade ratio, in this study was greater than 33 per cent. Air recovery based optimisation of air rates to banks of cells significantly improves flotation performance as it simultaneously determines the optimal air rate to the bank, and the optimal distribution of that air.

Jan 1, 2009

The iron ore deposits of-the Port Hedland distract of North-Western Australia are associated with banded-sedimentary iron., formations that.form part of the local succession. of folde.d..and faulted Archaean volcanic and sedimentary. rocks., The iron formations are regarded as the pr.otore,beds or sources of.the. iron which became;.,c,o.ncentrated by supergene.,processes. to form c,omznercial grade.. iron ore deposits,, ;-ò; Iron oxide ' deposit's occurring in"situ' within' the prot'ore beds are considered to be of residual--repplacement,origin`, due to supergene leaching of gangue minerals and deposition of secondary iron oxides in their'place'. Two types of deposit have been recognized. Lode deposits are deep lenses of massive hematite located adjacent to major, fau.lts... - These; deposits are-thought-to be very.,,old' and-to: have originated by supergene processes:.. during the, long: period of_ erosion represented- by the major, unconformity between the, Archaean .rocks and the, over!.

Jan 1, 1964

By B Cooper

During the design of a new production facility for a greenfields or significant brownfields expansion many design decisions are made driven by an unquestioning objective to achieve 'lowest cash-cost' production costs. In many cases this translates to a design and operating philosophy based on largest-available, single-line equipment. Although acknowledged as an approach that is efficient from an operating cost perspective does this approach always maximise shareholder value? There is an increasing awareness in the mining industry of the value of project flexibility, robustness and value options. The design of a new production facility creates a window of opportunity which should be structured to ensure that project value options and robustness are understood and exploited. This requires the use of emerging valuation methodologies, such as Value-at-Risk and Real Options, as well as tried and trusted NPV/IRR approaches. The paper provides an overview of the basis and application of these less well known techniques in the context of metallurgical plant design. Design guidelines that demonstrate how value options and flexibility can be quantified from both a risk and value perspective are presented. Issues such as use of single versus multiple line equipment, optimum cut-off grade and improved exploitation of the inherent variability of the orebody are also examined. Finally the management issues and approaches to achieving this will be briefly discussed; for example it is common during project development to drive towards increasing certainty as rapidly as possible to facilitate 'accurate' estimation of costs. Understanding and exploiting value options requires a project culture that tolerates, and revels in, ambiguity and uncertainty û something that would make many project teams uncomfortable!

Jan 1, 2008

Future depth and production limitations of an ore hoisting system are fixed by its initial design criteria. There is little scope to extend these limitations once installation is completed. Depth and production rate upgrades from the initial duty to the hoistÆs practical limitations require capital expenditure in stages, each of which can be defined when assessing the initial system design criteria. A means of presenting and assessing the design criteria, the limiting factors in each option and the relative present and future capital costs is necessary to arrive at a solution that delivers the best value to the mine. Application of this technique to recent friction winder installations and upgrades in the Australian mining industry is of particular interest; however, the analysis methods are also applicable to drum hoists. It is usual to specify a minimum hoisting capacity and depth, based on mine ore handling design and production needs. The final hoist depth and production rate are usually a result of the initial hoist design and hence it is useful from the outset to specify a required production versus depth envelope for the mine. Technical solutions can then be modelled within this envelope at their initial and final duties and a comparative analysis made against the cost of installing and progressively upgrading each solution. Understanding the factors that constrain each solution to a maximum production rate at a given depth is important, as the costs of overcoming limiting parameters such as rope tread pressure and motor power can be significant. The task of understanding and evaluating the options open to the hoisting system designer is simplified using this approach. Communicating the results of a multi-dimensional problem such as hoist specification is also made easier using the graphical methods inherent in the analysis.

Jan 1, 2005

An efficient stores organisation is essential for an efficient undertaking. Unless the stores organisation is able to meet the requirements of its requisitioners promptly and economically, the undertaking as a whole cannot function efficiently.Delays or errors in supply of material, or substitution due to lack of material availability from the stores are costly and must be eliminated. This then makes the objective of a store, to supply on demand at the cheapest possible price, those items of stock which it is organised to carry, also to procure as quickly as possible and at the lowest price those special items required which are not normally carried in stock. To do this it is necessary to set up a stores organisation consistent with the size and requirements of the undertaking. Stores organisations vary with the nature of the undertaking they are designed to serve. In the case of the Broken Hill Associated Smelters Pty. Ltd., an organisation has been established to meet the operating and maintenance requirements of the Port Pirie Works. These embrace the particularly wide range 0:1; activities associated with roasting" blast furnacing and refining the lead concentrates from the Broken Hill Mines in a continuous metallurgical process producing a variety of refined metals; also many associated activities including power production and engineering maintenance and construction.

Jan 1, 1951

By C P. Kramers

The need to provide a sufficient quality and quantity of backfill continues to increase in South Africa, particularly as related to the increasing depth of mining. More and more applications require well designed fill systems either as classified or cemented backfill, and in some applications even tailings/aggregate based backfills. The paper discusses developments in backfill technology in South Africa with special emphasis on reliable system designs and operations, particularly as related to the preparation and hydraulic transportation aspects. Approaches for the alleviation of previous problems associated with premature pipe failures in vertical shaft columns for the distribution of tailings based backfills are discussed. Resulting from CSIRÆs developmental work, reliable full-flow systems, which can operate at low system pressures, have become a common practice, provided that backfill flowrates and internal pipe sizes are well matched. This aspect is reviewed. With regard to the tailings/aggregate based backfills the paper reviews some of the results of comprehensive in situ monitoring and the development of such systems. It is shown that a thorough understanding of the effects of aggregate top size, fines content and slurry relative density is required in order to ensure the restartability of temporarily shut-down pipelines. Some innovative technologies for the comminution of development waste underground to yield aggregate products potentially suitable or hydraulic transportation and backfilling, are briefly discussed.

Jan 1, 1998

The economics of gold differs from that for base metals mainly because a large component of gold demand is investment or stock demand whereby the metal is purchased and stored for monetary or anxiety motives rather than fabricated into industrial products.The second major component of gold demand is fabrication, principally into jewellery but also, to some extent, into industrial products.Supply to the Western private- gold market comprises non-Communist mine production, Communist sales (chiefly from the USSR), and, finally, net sales by the Western Central Banks, which have total stocks of about 35,000 tonnes and which are sometimes net buyers as well as sellers.The different components of demand and supply fluctuate from year to year.

Jan 1, 1984

By C Smith, D Lilly

The Lafarge Marblehead Plant in Marblehead, Ohio, USA produces 4.2 million tonnes of sized aggregate yearly. In 1997, a program was instituted to maximise primary crusher productivity through the optimisation of blasting variables and procedures. A proprietary blasting shot report database and the Lafarge production database was statistically analysed to provide guidance in the program. Blasting powder factor (kg/m3) was the main control variable utilised to increase crusher throughput. In 2005, the program was refined to increase the production of certain high margin aggregate sizes and the reduction of fines. The principal blasting component affecting the percentage of high margin size production appears to be pattern area (burden and spacing area). This can be coupled with powder factor to optimise the production rate of high margin aggregate sizes. The size optimisation program incorporates the blasting shot report database, Lafarge production database, statistical analysis and aggregate sampling. A preliminary indication is that the production of high margin sizes (12.7 mm X 4.8 mm, 24.4 mm X 12.7 mm, and 50 mm X 25.4 mm) has been increased seven to 12 per cent utilising these techniques. As an added benefit, blasting costs have been reduced linearly as burden û spacing pattern areas have increased and powder factors have decreased. The program is ongoing and will investigate other blasting procedures and variables including electronic blasting caps to further increase the production of high margin products. The statistical methods involved in the analysis are described in this article for use in other mines and situations. The methods described can be used to optimise crusher throughput, digging rates and product size.

Jan 1, 2007

Mining of the silver-lead-zinc orebodies at the George Fisher Mine officially started in 2000. A review of mining performance to date shows that many of the extracted primary stopes have experienced some degree of hangingwall dilution. The degree of hangingwall failure in the stopes became progressively more extensive throughout mining of the orebodies in 2001 and 2002, culminating in the unplanned catastrophic failure of the 744D stope in which the ore between 13C (2683RL) and 12L (2714RL) sublevels caved into the previously mined cavity between 13L (2654RL) and 13C sublevels. This was followed several months later by another unplanned caving event in a nearby stope, 740D. As a direct result of these unplanned failures it was decided to mine the stopes with a smaller span than had been previously planned and in a primary-secondary pyramidal stoping sequence. To limit the exposure of the stope hangingwall, a hangingwall drive is no longer developed and therefore geologists no longer have access to the detailed geological information that this provided. Geologists at George Fisher Mine have had to be adaptable and flexible in response to these proposed changes and rely more on data from drilling than mapping for their geological interpretation. The result is that the drilling cycle has become much more critical in the planning process.

Jan 1, 2003

Welcome to this 13th Congress of The Council of Mining and Metallurgical Institutions. It is twenty one years since The Australasian Institute of Mining and Metallurgy last hosted this congress and it is a privilege and a pleasure for The AusIMM to have that responsibility once more. The theme of this congress "The Twenty-First Century - Mining for Mankind" stimulates many thoughts. The first thought that it generates in me relates to the reference to the 21st Century. We are still 14 years away from it and already consideration of the beginning of the next millenium is becoming something of a cliche. If we feel like that about it now, how will we feel at the 14th Congress of the CMMI in 1990, or the 15th in 1994 or the 16th in 1998? If we do all the crystal ball gazing about the 21st Century this week, those poor devils in the 1990s will in fact have nothing to talk about. Of course that is not the case. This is a very appropriate time for those of us concerned with mining and metallurgy to contemplate the next century. Fourteen years is about the extent of forward planning necessary in the mining business. I sometimes feel that most people do not take seriously the need for long range planning in our industry. Politicians, investment fund managers, and others under severe short-term pressure to perform in our hyperactive world may nod in apparent appreciation of our long term plans but their actions in the interests of expediency often betray-them.

Jan 1, 1986

Fluid inclusions and sulfur isotopic compositions were studied in a possible extension of the Toyoha polymetallic vein deposit. The objective of this work was to gain a better understanding of the ore depositional conditions, sources of ore constituents, and distribution of mineralizing fluid in the region. Fluid inclusions in sphalerite and quartz show that most homogenization temperatures range between 190¦ and 290¦C. Most salinities range from 0.0 to 3.4 wt per cent NaCl equiv. Sulfur isotopic compositions of ore minerals (pyrite, sphalerite and galena), determined by a conventional technique, range between 1.3 and 7.7 per mil. The mineralizing fluids were characterized by relatively low and various temperatures and low to moderate salinities compared to those at the southeast region of the main ore bodies (Izumo and Shinano veins) where rare elements such as tin, tungsten and indium occurred. Obtained temperatures and salinities were attributed to the mixing of hydrothermal fluids with groundwater. Sulfur isotopic data suggest sulfide sulfur was of magmatic origin. Isotopic temperatures, estimated from the isotopic fractionation factor between sphalerite and coexisting galena, are between 195¦ and 322¦C. The temperatures are only consistent with fluid inclusion homogenization temperatures in sphalerite or coexisting quartz when sphalerite was a honey-yellow coarse crystal lacking conspicuous colored growth bands. This suggests the detailed classification of mineral pairs growth textures will be necessary for precise in situ measurements to obtain reasonable eothermometric results.

Jan 1, 2002

The reality is that in today's world almost half of nearly six billion people on the planet do not have access to commercial energy and the services it brings. Based on UN projections, in 30 years time there are likely to be nearly three billion more people in the world, over 90 per cent of them in countries which are already economically poor. The World Energy Council (WEC), through its 102 member countries, monitors trends and developments and projects future trends. WEC is a non-governmental international body representing all forms of energy and is committed to the sustainable use of energy for all mankind. This paper is based on WEC studies and papers presented at its many conferences and congresses worldwide. Primary energy demand growth is dominated by the developing countries over the next 30 years. The world energy mix is projected to change very little over the next 30 years. Fossil fuel supplies (ie coal, oil and gas) are likely to decline from 77 per cent to 73 per cent, nuclear energy may grow from five per cent to six per cent and renewable energy sources (eg hydro, solar, geothermal, wind, tidal and biomass) could increase from 18 per cent to 21 per cent. World energy consumption is expected to grow by over 50 per cent over the next 30 years. The paper reviews changes in energy demand in the world, particularly in the Asia/Pacific region. Environmental issues are covered, as are developments such as solar energy from space and the status of renewable energy forms. Agendas for action to achieve change are also reviewed.

Jan 1, 1997

By El-Ansary M

Estimation of in-situ resources and recoverable ore reserves for the Boddington Gold Mine feasibility study was done by applying an essentially "classical" ore reserve method. This relied completely on customized graphics-based computer software requiring close co-operation and interaction between geologists and mining engineers. All geological and mining outlines were interpreted and digitized manually. Classification of selectively mineable reserves into ore, marginal and waste categories was done using a method involving convolution, devised by Dr S Carras of the Systems Research Institute of Australia, and Mr R Hooper of Kinhill Stearns. The estimation process was complicated by the frequently conflicting requirements of the various joint venture partners. The resulting ore reserve figures therefore satisfied only the most general expectations of each partner.

Jan 1, 1987

The paper discusses the characteristics of Be-zymianny activity during the last 2500 years. Three periods of increased activity have been identified which are the eruptive cycles lasting for 100-400 yrs. The periods of high activity fall on the fol-lowing time intervals: 2400-1700 yrs ago, 1350-1000 yrs ago and from 1955 ixp to the present time. The 1955-1956 catastrophic eruption after a long period of repose (about 900-1000 yrs) opened a new cycle of activity of the volcano which is continuing to-day. Several decades are distinguished in activity which differ in character and intensity of eruptions.

Jan 1, 1990

The management of safety has undergone a number of radical changes in the past 100 years. The most important paradigm shifts occurred through the work of Heinrich, followed by the advent of the safety systems era and, more recently, the behavioural safety approaches that have become increasingly popular around the world. Each of these æapproachesÆ to safety has left an indelible mark on the way we target safety improvements, helping decide which interventions are deployed and how they will be measured. They have also resulted in a number of æmythsÆ about safety management, each of which will be discussed, analysed and challenged in this paper. This paper highlights the complex problem of æcomplacencyÆ, that has arisen out of the increased levels of regulation and consequent perceived protection that workers enjoy in the work place. It also looks at a phenomenon called æaccident migrationÆ which results from a superficial treatment of accidents with changes to rules and procedures. The most recent approach to safety is generally known as behaviour-based safety, which flowed from the human sciences and quality management era. This approach has had a dramatic impact on the way safety is managed around the world, but still falls short in a number of key aspects, most notably the area of risk awareness and risk understanding. Many workplace accidents occur simply because the risk is unidentified, underestimated, not understood or ignored. This paper proposes a new direction for safety, called competency-based safety. It is based on cognitive psychology aimed at combating the consequence of modern protection. A case study is presented detailing the deployment of this approach throughout Placer Dome.

Jan 1, 2005

By P Rourke

In this climate of increasing demand for commodities, it is becoming necessary to expand and optimise existing bulk material handling facilities in order to increase capacity to satisfy demand. Production capacity in these facilities is often adversely impacted during the expansion process. A successful and proven strategy to reduce this impact is to bring the additional capacity online in stages coinciding with routine maintenance or other short shutdowns. Compatibility of the automation systems with staged upgrades in capacity is the key to achieving a successful outcome. Since 1994, Hatch has been researching a generic, highly configurable product transport control system that can be reconfigured to cater for plant expansions or modifications without incurring significant risk to production capacity. In 2002, BHP Billiton Iron Ore (BHPB IO) recognised the need for such a generic Route Selection and Sequencing (RSS) system and engaged Hatch to build a generic RSS system as part of the $US351 million BHPB IO Products and Capacity Expansion (PACE) project. In 2004, Hatch successfully deployed such a generic configurable control system at BHPB IO Port Hedland Ore Handling Facility. This generic system is known as the Hatch Product Transport (HPT) System.

Jan 1, 2005

The reduction of titanium tetrachloride to trichloride can be achieved by employing hydrogen and electric arcs. It is possible to produce melts containing up to 50% TiCk in the eutectic mixture of LiCl/KCl by striking a D.C. arc at the surface in the presence of hydrogen and TiCl. vapour. If the electrode IS made to just penetrate the surface of the salt mixture, a hot zone results from the' high resistance contact with both lower chlorides and sintered titanium may be produced. The sintered metal forms just below the melt surface while the trichloride forms at the gaslIiquid junction.The "hotspot cathode" appears to offer a solution to the problem of producing coherent deposits as the spong'e metal can 'be continuously withdrawn in a similar manner to the "calcium process".INTRODUCTIONConsiderable interest has been shown for some years in the possible development of a cheap electrolytic process for the extraction of titanium metal, since a method using simple materials and cheap electric power would materially reduce the cost of production. Even when cheap starting materials are used, however, there exist several general difficulties in the operation of plant which both limit the speed of production and increase the cost of the product. It happens that most of the techniques so far tried produce a powder as cathodic deposit, and when this is the case the following difficulties arise:1. The whole contents of the bath must be treated with solvent in order to extract the 'metal powder which may itself tend to oxidise, and thus become contaminated.2. Fine metal powders, which often contain residual entrained salts, are less easy to consolidate by arcmelting than metal sponge.

Jan 1, 1956

By Boontanjai C, Boyapati ER

Reagents used for batch flotation tests were Aeroxanthate-343 & 350, Dow Z-6, & reagent-4037 (from Benambra) as copper collectors; Na2SiO3 & Na2S2O3as gangue depressants; lime & HCl as pH regulators; and pine oil & MIBC (methyl isobutyl carbinol) as flotation frothers. A Denver Sub A flotation cell of capacity 250 gms was used for the batch flotation experiments. Atomic absorption spectrophotometer was used for copper assays and microscopy for selectivity and liberation studies. Melbourne tap water was used throughout the experiments. Unless otherwise stated, the following parameters apply to the flotation experiments: flotation impeller speed - 1300 rpm, pulp density during flotation- 22%, reagents addition - in 4 stages, total conditioning time for collectors - 8 minutes, total flotation time- 9 minutes. A variable quantity of copper mineral collector according to the test in question was added, then conditioned the pulp for 2 minutes. The froth was removed by hand, scraping the full length of the cell at constant depth every 10 seconds. No frother is required for this copper tailing flotation. Four concentrates were collected after addition of collector and conditioning at 2,4,6 and 9 minutes. The pulp volume was maintained at a constant level to yield a constant froth depth.

Jan 1, 1990