Search Documents

By Newell R

The situation in which a gas stream flows through a bed of solids is found in many extractive metallurgy operations. Examples include blast furnace smelting, sintering and pellet firing. In such cases the resistance of the bed to fluid flow and heat transfer is of major significance to the operation of the process. This depends on the structure of the bed, which in turn is influenced by the manner in which the materials are charged to the bed. In this work, packed beds of hematite pellets of two different sizes were prepared in which the pellets were charged as a uniform mixture and in layers. The porosity, flow resistance and heat front velocity were measured and compared for the different bed configurations. For layered beds, the overall porosity and heat front velocity increased while the flow resistance decreased when compared with the values obtained for the uniform mixture. The size of the layers also had an effect on flow Properties.

Jan 1, 1991

By Morrison AL

The volume changes occurring during the reduction by hydrogen of single, high-grade hematite pellets under isothermal and non- isothermal conditions were investigated using a time-lapse photographic technique. The major cause of swelling during iso- thermal reduction at temperatures in the range 600-1000¦C, was the disruptive stresses set up during the transformation of hematite to mag- netite. The severity of the disruption was temperature dependent; the degree of swelling increased with increases in the reduction temp erature. Under non-isothermal reduction conditions, in which the pellet temperatures were increased at constant heating rates over the temperature range 500-1000¦C, minor swelling (6-8%) occurred in the initial stages of reduction followed by pellet contractions of up to 15% in the final reduction stages. The low initial swelling and high final pellet shrinkages were due to a com- bination of the temperature dependence of the swelling mechanism, and the sintering of fine pores in the reduced iron in the latter stages of reduction at higher temperatures.

Jan 1, 1980

By Murakami T, Tamiya M, Mizokawa T, Matsumoto T

In the expansion program of the iron ore pelletizing plant at Kakogawa Works of Kobe Steel Ltd., an automatic computer control of products fineness on grinding department is practised. The main problem of the process control of a grinding system is scattering of measured fineness values of products. The scattering comes from the inherent nature of grinding systems, sampled powders and measuring systems. A method is developed to presume the exact status of the plant from scattering products (fineness values and to achieve a stable con trollability of the plant by utilizing the computer. An on-line fineness analyzer, an automatic sampling device and vari-speed air separators are also developed to compose the automatic grinding plant. This report introduces the fundamental epts and results of the automatic fineness rol system of the grinding plant.

Jan 1, 1977

By J Karlovšek

Civil engineering infrastructures are often subjected to different types of natural and mechanical activities. These influences may result in serviceability or even in stability of structures due to material deformations, increased water content within the materials used or the formation of internal or adjacent cavities that may threaten the infrastructure. Construction practices can lead to development of such defects in the form of cavities. In civil engineering it is crucial to detect these variations in material properties and to detect the presence of defects. However, as they are often hidden from view, these attributes may be difficult or impossible to target with traditional testing methods. For these reasons rapid geophysical methods, such as ground penetrating radar (GPR), are increasingly being used. At the University of Queensland (UQ) GPR is used for detection of voids and cavities which have been caused by an over excavation of the earth pressure balance machine (EPB) operating in a closed mode.A variety of numerical simulations using the finite-difference time-domain (FDTD) methods and preliminary experiments have been carried out in order to specify information about the nature, type, size, location and other characteristics of targets to be detected by GPR. In doing this the difficulty of interpreting GPR data, which is mainly due to the complexity of the factors involved in multiple possible solutions of the observed features, can be overcome.

Mar 8, 2011

By A Valero, G M. Mudd

There is active debate and research around the most suitable indicators to assess the sustainability of mining. The most common approach is to report a range of data for a given mine site (or less preferably, a company total), such as inputs, outputs, benefits and potential costs. The most popular protocol in use (and growing rapidly) is the Global Reporting Initiative (GRI). However, these measures are numerous and still do not allow a single over-arching indicator to be developed. Other measures, such as known mineral resources over time, do not account for critical challenges such as declining ore grades, increasing wastes and poorer quality ores or more difficult mineralogy. By adopting a thermodynamic approach to sustainability, through the concept of æexergyÆ, it is possible to incorporate into a single measure the effective quality of mineral resources. Exergy involves the assessment of the minimum energy costs involved in producing a mineral resource with a specific chemical composition and concentration from common materials in the environment. The exergy of a mineral resource is evaluated from mineralogic composition, concentration (or ore grade) and, of course, quantity, by multiplying the unit exergies with the tonnes of the resource produced (or consumed). Since exergy is a thermodynamic quantity (ie energy or joules), it is additive across different minerals, such as iron ore to gold to copper or even oil and gas or coal û making it an ideal indicator to assess mineral resource sustainability at the industry scale rather than the individual mine scale. This paper briefly outlines the theoretical basis for exergy, and then presents a range of commodity case studies showing the application of exergy to the Australian mining industry. Overall, the usefulness of exergy is clearly demonstrated for use as a broad indicator of the sustainability of mineral resources at the national or even global scale.

Jan 1, 2009

By T Huynh, K Tungpalan, E Wightman, M Edraki, S Palaniandy

Most preventive environmental management practices promote proactive integrated approaches to waste management. For example, life cycle assessment is often used to find the ‘hot spots’ of environmental burdens. This kind of approach is often based on generic data and has rarely been used for tailings. Besides, life cycle assessments are less useful for designing operations or simulating changes in the process and consequent environmental outcomes. It is evident that an integrated approach for tailings research linked to better processing options is needed.The aim of this Nextmine™ project is to develop new tailings management models by streamlining orebody characterisation, process optimisation and rehabilitation. We present an integrated tailings management approach and preliminary results from a case study. Combined grinding and flotation models were developed using geometallurgical data from the orebody, to predict the properties of tailings produced under various processing conditions. The modelling scenarios based on the case study data provide the capacity to predict the composition of tailings and the resulting environmental management implications. For example, the type and content of clay minerals in tailings will affect the geotechnical stability and water recovery. Clay content will also influence decisions made for paste or thickened tailings and underground backfilling.CITATION:Edraki, M, Huynh, T, Wightman, E, Tungpalan, K and Palaniandy, S, 2015. An integrated approach to proactive tailings management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 323–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By P Holtham, K C. Runge, E Tabosa

Traditionally, comminution and flotation have been surveyed, analysed and optimised separately. This often results in less than optimal outcomes because of the complex interactions between the two processes. Flotation recovery is a strong function of the valuable mineral particle size distribution with lower recovery of ultra-fines due to poor flotation kinetics, optimum recovery for the intermediate sized particles and lower recovery for the coarser particles due to poorer liberation. Thus, to optimise flotation recovery and grade it is usually best to grind to a fine size. This requirement needs to be balanced by the cost of grinding finer and the revenue that results from an increase in grinding throughput, which often results in a coarsening of the flotation feed.This paper demonstrates a technique which can be used to predict the effect of a change in feed grind size on flotation performance. It can be used to determine the optimum grind size for a particular operation which optimises total circuit profitability. Analysis is relatively easy to perform, as a minimum, requiring only size by assay data of the feed and product streams of the process. Case studies will be presented that demonstrate the usefulness of this technique in feed grind applications. Potential use of the technique for regrind evaluation is discussed. The limitations associated with this technique in certain circuit scenarios will also be outlined.CITATION:Runge, K C, Tabosa, E and Holtham, P, 2014. Integrated optimisation of grinding and flotation circuits, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Tilley H. L

The 90 m deep Yallourn Open Cut brown coal mine in the Latrobe Valley, Victoria is developing into an area close to a reverse fault. A major batter stabilisation program, matched to ongoing operations, has com- menced to maximise coal recovery where the fault is within 100 m of the Open Cut. The various mine development options considered during the planning stages are outlined. These options were formulated in a back- ground of geotechnical constraints and the need to maintain continuous and reliable coal supply at a time when a new coal field would be developed. The geotechnical investigations and analysis procedures under- taken to determine stability of the batters during their excavation are presented. The geotechnical constraints on the mine design and opera- tions required to ensure safe working conditions are detailed. Current operational and batter stability conditions are considered satisfactory.

Jan 1, 1989

By M Norbert, P Mok

The mainline running tunnels for Legacy Way comprise of two-lane tunnel boring machines (TBM) driven tunnels. The length of the TBM tunnel section is approximately 4.2 km. The TBMs employed are double shield TBMs. Typical support to the segment ring while advancing a double shield TBM comprises of filling the excavated annulus between the ground and the segmental lining by injecting pea gravel, followed with primary grouting to fill between the pea gravel some distance behind the excavated face. The methodology adopted for the Legacy Way project, however, did not follow this typical approach, instead, two component grouting of the annulus was carried out.Where the annulus is typically filled with pea gravel, support is provided to the segment ring very close to the end of the tail shield, whereas in the case of two component grout this is not practical as the risk of grouting in the tail shield is high. The staging of the two component grout injection, the grout early age strength properties become key issues in ensuring that the segment ring leaving the TBM tail shield is stable and can support the necessary external loads.Two-component grout is a grout with two components, cementitious grout (component A) and accelerator (component B), commonly adopted for earth pressure balance (EPB) TBM. The grout reaches its thixotropic state in a matter of seconds providing initial support for the segment rings. Manual injection of two component grout to fill the bore annulus was carried out in stages leaving a portion of the segment rings unsupported. Ring stability during TBM advance was provided by a combination of ram thrust and the segment circumferential joint shear connectors.This paper outlines the design considerations such as rock load derivation by probabilistic analysis carried out utilising the software JBlock, 3D finite element analyses using the software Strand7 for ring stability and the testing and back analysis of the shear connector load bearing behaviour. In particular, the actual available capacity of the shear connectors against their published capacity by supplier was discussed.CITATION:Mok, P and Norbert, M, 2014. Tunnel boring machine excavation stability – double shield tunnel boring machine advance with partially grouted annulus, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

There is a Chinese saying-may you live in interesting times. Certainly we do tod.a~our mining professions. We are, of course, totally dependent on a' healthy mining industry for the chance to practice our chosen professions, and for our Institute.Let us look at one of the more interesting facts. The mining industry now accounts for some 50 per cent of Australia's exports.This massive earning of foreign exchange is the key to keeping our increasing overseas debt in check. Furthermore, mineral production..including petroleum, saves us a large amount of foreign currency by providing essential minerals, including energy minerals, for local consumption.With such fundamental inputs to our economy, any primary school student, any child in fact, should be able to see that the mining industry and mining professions are very important to our nation. Yet the average citizen is unaware of this simple fact as they enjoy their high standard'of living and think that we are still living in the lucky country.Therefore, it is most interesting to me that the average citizen, and most of our politicians, seem to hold mining and miners in low esteem. I use the term miners to describe all those important people, like us, who work in the mining professions, and are employed by, or are dependent on, the mining industry.So why are we miners in this paradoxical situation of doing wonderful works, being the backbone of the country, and yet being held in low regard by the very community we underwrite.Truly-it is interesting-or did the Chinese mean intriguing?It is indeed paradoxical that we are the rare people who open up the land, borrow small parts of it for a relatively short time to harvest the mineral crops, then return it to the community for other uses; and when we return the land back to the community at large it should be in better shape than when we started. There will be infrastructure - roads, airstrips, supplies of water and power, parks and housing-all left behind after mining.These benefits to the community are ignored while our critics focus on the small scars on the landscape which sometimes cannot be healed at reasonable cost; and yet, if we allow time, nature usually heals the small scars anyway. Look at New Zealand, particularly the Coromandel Peninsula which was intensively mined and logged; now it is covered with secondary growth and stark pine plantations. Remember that mining scars are infinitesimally small when compared to urban sprawl or clearing of land for farming and grazing, or highways, or the area of most national parks.Thus, miners are important citizens economically, and we are the majority of the few who actually practice the principles of multiple land use.What are the consequences of our image? They are serious in that the poor image we seem to project, discourages many people from becoming involved in, or supportive of, our industry. This brings me to my theme for the year: Students, Education and Communication - the Key to our Future.

Jan 1, 1987

By M Berry

Consider these four questions:What is the definition of life-of-mine?When should life-of-mine planning seriously commence?When can life-of-mine planning seriously commence?What is the key input to effective life-of-mine planning?Whilst there is likely to be general consensus on the answers to the first three questions, the answer to the fourth question is open to debate. This author argues that understanding and managing risks and opportunities associated with geological uncertainty is the key input to effective life-of-mine planning, at all stages in the life cycle of a mining project.CITATION:Berry, M, ?2014. Effective life-of-mine planning by understanding and managing risks and opportunities associated with geological uncertainty, in Proceedings Life-of-Mine 2014 , pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By H Lehtonen, H Mansikkaviita

In primary copper smelters, the received copper concentrate and other materials contain a certain amount of moisture, ranging from six to 14 per cent. Moisture in wet concentrate has a negative effect on the performance of the smelting furnaces when it is fed directly to the furnaces, namely increasing the energy consumption and the off-gas flow. There are several drying technologies available for drying copper concentrate, varying from direct heated rotary dryers and flash dryers to indirect heated steam dryers. Application of steam dryers has changed the drying process for copper smelters. Produced from a waste heat boiler, steam as heating medium enables plant-wide heat utilisation. Fossil fuel used from outside sources to remove water is no longer required and the combustion chamber is not required. In addition special attention has been paid to overcome the known problems of pollution emissions, excessive wear, clogging and frequent maintenance. The Kumera steam dryer is featured with many advantages based on principal improvements in reducing tube element wear and increasing drying efficiency. Thus, it has been considered as the first choice for those smelters where steam is available.

Jan 1, 2006

By A Hughes, J Agius, T Ferguson, A Parbhakar-Fox, D Lester, L M. Jackson

Management of historic tailings is a major challenge facing the mining industry and its regulators. However, through improved mineralogical and chemical characterisation of such materials the opportunity to develop better rehabilitation strategies arises. Microanalytical techniques including microscopy, mineral liberation analysis and laser ablation inductively coupled plasma mass spectrometry (ICPMS) allow for improved tailings characterisation – but the challenge posed by these techniques is how to use them effectively. Additionally, data sets collected by such techniques must be properly integrated, only then can they assist in the identification of the most appropriate rehabilitation strategies. A study conducted at the Old Tailings Dam (OTD) located at the Savage River Mine, Tasmania allowed for the integrated use of several microanalytical techniques to help evaluate the benefits of a shallow water cover as a potential rehabilitation strategy. Samples (n = 144) from 14 trenches and 11 boring cores (2 m maximum depth) were collected across the OTD. These were subjected to routine acid-base accounting, with a subset subjected to detailed mineralogy using a modified sulfide alteration index (SAI), X-ray diffractometry and mineral liberation analysis (MLA). In addition, representative samples (n = 6) from across the OTD were subjected to laser-ablation ICPMS to characterise the pyrite chemistry. Our results showed that tailings in the northern area submerged under a natural water cover were relatively unoxidised from approximately 1 m depth, with SAI values of 1 to 2. Tailings from the subaerial southern portion were extensively oxidised to approximately 35 cm depth (SAI = maximum 5.8), with fresher materials observed underneath (SAI = 5 to 5.8). Pyrite from across the OTD is enriched in Co, Cu and Ni. Through the integrated application of microanalytical tools, we determined that establishing a water cover of at least 1.5 m depth across the OTD is a suitable rehabilitation option for this historic site. However, consideration for the reprocessing of these tailings to extract Co should be further investigated.CITATION:Jackson, L M, Parbhakar-Fox, A, Hughes, A, Agius, J, Ferguson, T and Lester, D, 2015. Microanalytical evaluations of the savage river old tailings dam, north-?west Tasmania, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 111–124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S Norman

The Water Delivery Alliance (WDA) was established to design, construct and commission the pump station and desalinated water delivery pipeline to link the desalination plant on the Kurnell Peninsula (constructed by others) with the existing distribution network at Erskineville, Sydney, Australia. The WDA consisted of McConnell Dowell Corporation Ltd (Macdow), Bovis Lend Lease Pty Ltd (BLL), Kellogg Brown and Root Pty Ltd (KBR), Worleyparsons Ltd (WOR), Environmental Resources Management Group Inc (ERM) and Sydney Water Corporation (SWC).Sydney’s Desalination Project is one of the initiatives to secure Sydney’s water supply against the effects of climate change, population growth and drought. The desalination plant, 100 per cent powered by renewable energy, can supply up to 250 million litres of water per day (mld), which is up to 15 per cent of Sydney’s water needs. The project involved the construction of an 18 km pipeline with an ultimate capacity of 500 mld to accommodate any future increase in the output of the desalination plant.The Alliance procured three full-face tunnel boring machines (TBM) from Herrenknecht AG to construct the 6.5 km of tunnel that would provide a conduit for the DN1800 welded mild steel cement mortar lined (MSCL) pipeline at a number of locations along the route. Nineteen shafts and 16 tunnels were required to complete this work.Crucially one of the TBM drives involved construction of a tunnel into Botany Bay under protected marine life habitats; enabling the connection of the MSCL water carrier pipeline into the dredged section of pipeline underwater, approximately 800 m off-shore in Botany Bay.This paper details the retrieval of the 17.4 m long TBM from the ocean floor upon completion of the Botany Bay tunnel allowing for subsequent use on the Project. Elements covered in the paper include the 835 m tunnel, design and construction techniques for the tunnel and recovery, and details of the methods used to install the DN1800 water carrier pipeline.

Mar 8, 2011

By T Ireland, S Eratne, W Newns, P Spies

The approach to risk management during the procurement of major projects often has a significant outcome on the ultimate delivery of a project. The NZ$1.4 B Waterview Connection project is the largest and most complex project yet undertaken by the New Zealand Transport Agency (NZTA) and the procurement process for an alliance contract was refined to provide compliance with the International Tunnel Insurance Group (ITIG) Code of Practice for Risk Management of Tunnel Works (TCoP). The principle of shared risk within an alliance incentivises a common understanding of project risks prior to finalising the alliance agreement and therefore enables superior risk management through design, construction and beyond. Risk management practices need to be instigated well in advance of commercial phases, so that commercial competition does not lead to a significant elevation of project risk. In particular the practice of gaining commercial advantage by taking on a potentially unmanageable level of risk is one of the outcomes to be avoided by the TCoP.During the procurement phase the NZTA placed high value on design and construction mitigation measures proposed in order to address ground risks, as is appropriate for a major tunnel project. In order to achieve alignment on the level of geotechnical risks an Alliance Geotechnical Baseline Report (AGBR) process was developed.This paper describes the measures taken during the procurement process to achieve certainty with respect to outcomes and minimise project risks whilst also achieving value for money. Refinements to the procurement process to ensure compliance with the TCoP prepared by the International Tunnel Insurance Group (ITIG) are described along with the AGBR process applied as part of a suite of measures to achieve a successful procurement outcome.CITATION:Ireland, T, Spies, P, Eratne, S and Newns, W, 2014. Risk management and use of a geotechnical baseline report for a competitive alliance procurement?process, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 553–562 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

During the last 12 years the dominant theme at Mount Isa has been production expansion. Production rate of 3,200 tons per mine day in 1953 increased to 11,000 tons per mine day in 1960, completing the first stage of the programme. The second stage is still in progress. It is planned to increase production of lead and copper ores to 19,500 tons per mine day in 1968.Current mine workings comprise an area 2 miles long and 1/2 mile wide, the deepest production level being 2,000 ft below surface. During the next 10 years it is anticipated that mining will be carried out to a depthof 3,200 ft below the surface. The rapid extension of the mine has necessitated frequent re-appraisals and modifications to the primary ventilation system, and a system with considerable in-built flexibility has gradually evolved. Since 1953, volume circulation has increased eight-fold to approximately 2,400,000 c.f.m.To suit various mine operating requirements, a combined pressure-exhaust system of ventilation was adopted.The usefulness of this system is at a maximum when the fans installed permit ready changes in the location of the boundary between adjacent spheres of fan influence.Air flow through openings to the surface can be controlled or used as required. This feature is considered necessary for a mine where underground workings are comparatively shallow and caving to the surface willoccur.A major heat problem exists due to climate conditions, high geothermic gradient (one degree Fahrenheit in 95 ft), and oxidation in leached and brecciated areas.Because of this, quantities of air far in excess of the minimum requirements for dust removal are required to ensure satisfactory environmental conditions. In assessing fan pressure, consideration was given to 1. the mine resistance, and the requirement for pressure differential capability,2. the pressure requirement for deeper mining, with due allowance for booster fan use where appropriate,and3. the desire to avoid fan operation at pressure duties above the region of peak fan efficiency.The latter feature provides a safety margin between maximum operating pressure and the stall point of the fan.

Jan 1, 1967

By S G. Gemell

"The financial model is an integral component of any project evaluation based on mineral resources, ore reserves and (at least internally) exploration targets. Given the unity of purpose for preparing financial models for project evaluation purposes, the diversity of both format and content of the finalised models is surprising. Many models are prepared by staff or consultants who are comfortable with a particular format that may be used for other purposes, such as budget preparation or financial reporting. It is natural in these situations that the practitioner will take these models and adapt them to the purpose. The end result may or may not succeed in providing a clear, accurate and sufficiently detailed view of the project’s economic viability.When preparing a model, the practitioner should be cognisant of the interpretation and review, or audit, process. The auditor may be a consultant or employee of a bank, potential equity provider or of the project sponsor itself. Depending upon the scale of the project and the level of participation of the entity that the auditor represents, the financial model will be interrogated more or less rigorously. In any event, the end user will require the model to permit easy change of inputs and will wish to confirm that such change is appropriately and thoroughly transmitted throughout.Accordingly, there are some ‘dos and don’ts’ that can be readily applied in the creation of the financial model that will greatly assist the end user, not just in the change of inputs, but also in reviewing the model’s integrity. The less time and effort required by an auditor in this regard is reflected directly in the cost of the review process.CITATION:Gemell, S G, 2016. Financial modelling with the auditor in mind, in Proceedings Project Evaluation 2016, pp 172–180 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

State ownership of minerals results in domestic legislation regulating mining operations. The mining industry today is dominated by a number of transnational companies, each subject to internal and external pressures for a more responsible approach to resource management. Thirty to 40 major companies are responsible for the bulk of the worldÆs mineral production with the balance coming from state-owned, second tier and junior companies and from artisanal miners.Mining companies operating within competitive commercial environments formerly focussed on mineral production. Companies worked to standards and expectations then current which largely failed to recognise the impact of mining activities on community interests. The mining industry acquired a reputation for arrogance, and for placing profitability ahead of issues considered equally or more important by local communities. Current perceptions continue to reflect disquiet about industry attitudes towards traditional land-owners and access to their lands, to environmental contamination, handling and storage of waste materials, utilisation of water and electricity, and to rehabilitation of worked out areas. Major international mining companies concerned at continuing criticism sponsored a series of initiatives with the objective of providing guidance on working harmoniously within the community. Industry commissioned studies, performed through the agency of disinterested parties, resulted in May 2002, in a Declaration being issued at an International Conference in Toronto. The Declaration was based on, but did not reflect all of the recommendations of the MMSD Report, æBreaking New GroundÆ.This paper considers whether benefits would result from the negotiation of a legally binding and enforceable international protocol encompassing the objectives of the MMSD report or the Toronto Declaration. It attempts to identify the problems associated with implementing and enforcing international mining law, should it be introduced. Aspects of mining operations having cover under customary international law are reviewed, as are rights, obligations and remedies for breaches of national mining law. Conclusions are drawn based on established procedures relating to implementing international agreements. The continuing ability of mining companies to operate within communities will result from each satisfying the communityÆs expectations rather than by complying with largely unenforceable legislation.

Jan 1, 2004

By R Young

Independent Project Analysis (IPA) is in the business of benchmarking the performance of capital projects on behalf of owner companies in the processing and extractive industries. IPA assesses between 500 and 800 projects each year. The projects are conducted globally and range in size from about $1 million to over $30 billion. Using the data, we are able to benchmark the performance of Australian projects against the rest of the world. This presentation focuses on the performance of large (greater than $100 million) projects that involve chemical or thermal processing.We regularly hear calls for more processing to be conducted in Australia but on the other hand industry leaders are concerned about the poor success rate of solids processing projects in Australia. Data gathered by IPA indicates that there is good reason for the concern. Out of a sample of 31 large processing projects conducted in Australia, 23, or 74 percent, were classed as failures. This performance is significantly worse than for similar projects in other parts of the world. The presentation analyses why the performance is worse and demonstrates that many of the reasons behind the failures were manageable by the project team. Furthermore, members of the project teams on at least half the failed projects knew that the projects were on a path to failure before the project was authorised but could not be heard.The presentation discusses how large projects that involve process design and, in many cases, new technology, need to be set up for success. *This is an abstract only. No paper was prepared for this abstract.*

Aug 8, 2011

By M-A Van Ende, N Kumar, I-H Jung

In order to utilise the powerful thermodynamic databases for process simulations, a concept called Effective Equilibrium Reaction Zone (EERZ) was introduced to couple thermodynamic database calculations and reaction kinetics. Using the EERZ concept, many process simulation models for steelmaking processes have been developed within the FactSage steelmaking consortium. After validation of the simulation results by comparing with plant data, the simulation models have been applied to improve plant operations. Several success stories of the improvement of real steelmaking operations are shared. A new user-friendly FactProSim software developed for building process simulations is introduced.

Aug 21, 2024