Search Documents

C. Edward Stafford, Chester, Pa.:—Doring all my business life, I have been engaged in the manufacture of Bessemer and open-hearth steels, but, during my long connection with the Shoenberger Steel Co. of Pittsburg, I had some experience in the manufacture of high-grade puddled iron for horseshoes, and in making, by Dr. Otto Wuth's process, extremely pure, low-phosphorus puddled blooms (analyzing from 0.005 to 0.01 per cent. of phosphorus and sulphur), which were melted with low-phosphorus pig-iron in acid open-hearth furnaces, to make extra locomotive fire-box steel. I have also seen the Danks puddlers in operation at different times and places, notably where they were most successful, at the Otis Steel Works, Cleveland, Ohio; then under the management of our friend, Mr. S. T. Wellman. These Danks blooms were made solely for open-hearth melting-stock, to which they were well adapted. (The unavoidable presence of bits of ore-fix imbedded in the mass of the metal always prevents the profitable manufacture of merchant iron from Danks' blooms.) With the experience just described, I was to some degree in position to value fairly the means, methods and results of Mr. Roe's mechanical puddling from the metallurgical or technical and economic points of view, when given an opportunity by Mr. Roe to see his puddling-furnace or machine in operation in Pottstown, Pa. Briefly, the furnace, with water-cooled bottom, is rectangular in plan, about 20 by 8 ft. in the clear, suspended by trunnions at the middle of the long sides, at a height of 17 or 18 ft. above the general level. The oscillation (65" each way from the vertical) is accomplished by geared segments (attached to the downward-projecting side or trunnion-plates) with which engage pinions driven by a reversing engine. The whole section

Jan 1, 1906

By John V. Beall

Cutting costs and increasing safety with new ideas is the byword with The Cleveland-Cliffs Iron Co. on the Marquette Range in Michigan. Among the new ideas being tried out are mechanical shaft mucking, prefabricated lagging to replace timber poles, Carset bits in shaft sinking, and rubber tired guide wheels on the ore skips. Plans are being made to stockpile ore with conveyor belts during the winter. In sinking the Mather "B" Shaft a 3/8-yd clamshell-type bucket is used for mucking. The clamshell is opened and closed by means of a verticallymounted hydraulic ram actuated by 5000 psi oil pressure. An Ingersoll Rand-type hoist is used to raise and lower the clamshell. The hoist is controlled by one member of the crew on the floor of the shaft. When the bucket is raised, the men swing it over the muck pile to the desired position and then it is lowered on to the broken rock. The 1400-lb weight of the bucket causes it to sink into the broken rock and it digs as the ram closes the bucket. The hydraulic ram is operated by a man on the lowest shaft steel set who controls a specially designed oil pump which supplies oil pressure. The clamshell is emptied.

Jan 1, 1949

By AIME AIME

I N JUNE, 1918, at a meeting of the American Society of Mechanical Engineers in Worcester, Mass;, a resolution was adopted for a committee to investigate the aims and organization of that society. This was followed subsequently by similar independent action on the part of the Society of Civil Engineers. The other two Founder Societies were approached and requested to appoint similar committees, the four committees to combine as a .Joint Development Committee, later called the Joint Conference Committee, to investigate what might be done in the way of coordinating those activities of the Founder Societies which ape of common interest, and which were then being pursued separately. The Joint Conference committee worked diligently -for almost. two years and. brought forth a tentative as outlined in its report which was published in full in MINING AND. METALLURGY, December, 1919. It recommended the formation of a nation-wide organization to be composed of representatives' of all of -the engineering societies, local, state, regional, or national, the object to be to further the interest of the public through the use of technical knowledge and engineering experience, and to consider and act upon matters common to the engineering and allied technical professions. Whereas the technical societies have large fields of endeavor in welfare work, and their prime. efforts are 'still in technical lines, this new organization was to be devoted entirely to service, looking to the welfare of the nation and the engineering profession, and to service for the public in local and state affairs.

Jan 1, 1920

By T. S. Spice, H. L. Lovell, R. W. Utley

With the increased demand for lightweight aggregate, such materials have been manufactured from slags, clays, slates and, to a minor extent, the refuse of coal preparation processes. The latter source is attractive due to current interest in eliminating air pollution and improving the unsightly appearance of refuse piles as well as potential economic advantages, if a satisfactory product can be manufactured. A study has been made relating the composition of coal refuse, expressed as washability data, and the properties of a resulting aggregate. Three different refuse samples (bituminous and anthracite) were separated at gravities ranging from 1.4 to 2.96. Their chemical composition was determined. Aggregates were prepared in the laboratory from these fractions before and after ashing, at temperatures between 1250' and 1350°C. The specific gravity, expansion and compressive strength of the products were measured. The response of the refuse to bloat is related to the chemical composition of the ash to yield a glass of desirable viscosity and to the presence of a material which will form a gas in the appropriate temperature range. Carbonaceous material within the particle is a negative factor since after the glassy phase forms, oxygen cannot enter the mass thus inhibiting bloating. Precombustion of the refuse is also detrimental since it removes substances of gas-forming capability. The fraction sinking at 2.60 yielded an aggregate which had the lowest specific gravity, greatest expansion and greatest compressive strength. The purpose of this study was to seek and evaluate possible relationships between the composition of coal refuse, as expressed by washability data and factors affecting the production of a lightweight aggregate from refuse by bloating. The study was related to an intense program in the Department of Mineral Preparation at the Pennsyl- vania State University to study the possible elimination of air pollution from coal refuse fires by producing a low-carbon secondary refuse. Another phase of this program is considering possible uses of such a secondary refuse. Thus one study was to determine if a lightweight aggregate could be produced from this new refuse material and what effect the nature of refuse beneficiation would have upon the characteristics of a commercial aggregate product. It was hoped that these studies would assist in the design of a process and in establishing the optimum specific gravities at which refuse separation could be made in respect to the production of a low grade fuel from the float product and a raw material for lightweight aggregate from the sink product. The combination of producing a saleable low grade fuel and a lightweight aggregate, while at the same time minimizing disposal costs and air pollution contributions would be attractive to the coal mining industry. MECHANISM OF BLOATING Austin, Nunes and Sullivan,1 Ehlers,3 Everhart, 4 Riley7 and others, have stated that bloating is an expansion process in which two essential conditions exist simultaneously. These are: the development of a glassy phase over a relatively wide temperature range (the viscosity of this glassy phase plays a major role in the retention of the evolved gases) and the evolution of gases (SO2, SO3, CO2 and O2) from mineral decomposition in sufficient quantities at appropriate temperatures to form a cellular structure in the mass. Unless these two "type" reactions take place at the same time or in overlapping ranges of time and temperature, cellulation will not occur. In this event, the gas will escape or the melt will be too fluid to retain it; or if retained, the cells may be too large or the walls too thin for good strength in the product. The stages that occur when clays and shales are heated in an oxidizing atmosphere may be summarized as follows: 1) Drying and removal of free water to 200°C. 2) Absorbed water dehydration period (200 to 480°C). 3) Chemically-combined water dehydration period (480 to 700°C).

Jan 1, 1965

By J. E. Papin

MORENCI ores contain as an average about 0.015 pct molybdenite, MoS2. Incidental to the concentrating operations applied for the recovery of copper minerals, approximately two-thirds of the molybdenite is floated and appears in the final copper concentrate. The economic importance of molybdenum and the success achieved in its recovery in milling operations elsewhere encouraged research directed toward its recovery in marketable form. Several procedures are utilized to effect separation of molybdenite from copper and iron sulphides, but only two have wide application. In the better known of these two methods the molybdenite in the copper concentrate is depressed in a flotation operation using soluble starch as the depressant. The tailing from this treatment thus becomes a low-grade molybdenite concentrate which after thickening, filtering, and low temperature roasting is repulped with water and subjected to additional flotation steps for recovery of the molybdenite. A thio-phos-phate collecting agent is employed in flotation of the copper minerals. Presumably the stability and lasting effects of that collector type necessitated the practice of depressing molybdenite followed by subsequent roasting to insure elimination of copper and iron sulphides from final molybdenite concentrate. The second important method of recovery is applied at various southwestern plants. In those plants xanthates are in use as copper collecting agents. It has been found that xanthates are relatively unstable and their collecting power for sulphides is destroyed by very simple procedures. The method generally applied is to subject the xanthate-acti-vated concentrate, in the form of a pulp, to prolonged heating using steam as the heating medium. A concentrate thus treated may then be subjected to a flotation operation for recovery of the molybdenite, using mineral oil collecting agents, and the copper and iron sulphides will be depressed. Neither of the above processes was applicable to Morenci concentrates. Morenci uses a thio-phos-phate collecting agent in its flotation operation. However, it was established that soluble starch was not a depressant for Morenci molybdenite; therefore the first step in that process was not applicable. AS would be expected the copper and iron sulphides in Morenci concentrates could not be depressed by the heating methods used on xanthate activated concentrates. Low-temperature roasting did eliminate the effects of the thio-phosphate but had to be rejected as uneconomic in as much as the tonnage of concentrates involved was too great. Preliminary research having established the above facts, it became obvious that new methods would have to be developed for the recovery of molybdenite from Morenci concentrates. A broad laboratory investigation was initiated along two general lines, both directed toward depression of copper and iron sulphides. One approach was through the use of water-soluble oxidizing agents with the objective of destroying the thio-phosphate in the concentrate and thus eliminating its collector effect. The other approach involved the use of soluble sulphides, which have long been recognized as sulphide depressants. These efforts resulted in laboratory processes which showed promise. Research was then extended to a pilot plant having a daily capacity of several tons of concentrate. This operation soon demonstrated that soluble sulphide—basically sodium polysulphide—when applied to a pulp made slightly acid with sulphuric acid, proved to be the most effective sulphide depressant. The rate of concentrate treatment in this plant and the low molybdenite content of the concentrate prevented carrying the process to a conclusion, namely, production of molybdenite concentrate of marketable grade. Laboratory treatment of pilot plant concentrate indicated that a marketable product could be made from it, given a tonnage suited to available cleaner flotation machine capacity. Accordingly, the molybdenite plant was enlarged to permit treatment of the total copper concentrate from the extension plant, maximum of approximately 800 tons per day. In the enlarged plant a major difficulty was encountered. No criteria could be established as a basis for control of the process. In the early stages of flotation, because of the small amount of molybdenite involved, there was no visual evidence of the relative floatability of molybdenite with respect to

Jan 1, 1956

By E. F. Koch, J. L. Walter

oriented crystals of iron and iron with 3, 5, and 6.25 pct Si were rolled to reductions of 10 and 70 to 97 pct at room temperature. Similarly oriented crystals were deformed in tension. Dislocation substructures of the deformed crystals were observed by transmission electron microscopy to determine the effect of silicon on the formation of substructures. Pole figures were obtained to relate orientation changes to substructure. When rolled 10 pct, the iron crystals and the 3 pct Si-Fe crystals formed cells, 1 and 0.2 u in diameter, respecliuely. Cells were absent in the higher-silicon crystals. Extended dislocations and possible stacking faults were observed in the 6.25 pct Si-Fe crystal rolled 10 pct and annealed at 650°C. The stacking-fault energy was estimated to be 20 ergs per sq cm. Rolling to 70 pct resulted in the formation of sub-bands (0.9 µ wide) ill the iron crystals and transition bands (containing 0.2-µ-wide subbands) in the 3 pct Si crystals. No subbands formed in the 5 pct Si-Fe crystal until it was ankzealed. SliP occurred on (112) planes ill tension. The slip traces on the 3 pct Si crystal were wary while those on the 5 pct Si crystal wvere straight. The strain-hardening coefficient for the 5 pct Si crystal was nearly zero. Cells did not form, at least at elongations up to 10 pet. The results suggest that cross slip of iron is restricted by additions of silicon beyond about 3 pct possibly by formation of immobile extended dislocations. IN a previous paper' the authors described the substructures developed in (100)[001]-oriented crystals of 3 pct Si-Fe which were rolled to reductions of 10 to 90 pct at room temperature. At low reductions (10 to 20 pct) cells, approximately 0.2 to 0.3 ja in diameter, were formed. The cell walls consisted mainly of edge dislocations. With increasing reduction (up to 50 pct) the cells were seen to elongate in the rolling direction. In certain regions of the crystal there were significant reorientations which were characterized as rotations about an axis normal to the (100) or rolling plane. These regions were called "transition bands". The regions in which there were no reorientations were called ('deformation bands". At reductions of 60 to 70 pct the elongated cells in the transition bands became sub-bands separated by low-angle tilt boundaries with angles of disorientation of about 2 deg. The elongated cell structure in the deformation band was replaced by a general distribution of dislocations. It was noted that the width of the subbands in the transition bands remained 0.2 to 0.3 µ; i .e., the width of the subbands was the same as the initial cell diameter for reductions up to at least 70 pct. From this, and from considerations of the mechanism of formation of the transition bands,' it was concluded that the subbands evolved directly from the initial cells. In order to check this conclusion, it was decided to examine the relationship between initial cell diameter and width of subbands produced by large rolling reductions. Cell size is known to be dependent upon the temperature of deformation.2,3 However, preliminary experiments with 3 pct Si-Fe crystals indicated that the change in cell size with increasing temperature of deform,ation was not sufficient for the present purpose. On the other hand, cell diameters generally reported for iron deformed at room temperature2'3 range from 1 to 2 p, a factor of 3 to 10 larger than the cells in 3 pct Si-Fe rolled to 10 pct reduction,' indicating the possibility of a marked dependence of substructure (at least in terms of cell size) on the amount of silicon in iron. Thus, the investigation was enlarged to include the study of the effects of varying silicon content on substructure in lightly rolled as well as in heavily rolled crystals of iron and iron with 3, 5, and 6.25 pct Si. The crystals used in this study all had the same orientation, (100)[001], with respect to rolling plane and rolling direction. These were rolled to reductions of from 10 to 97 pct and the substructures determined by electron transmission microscopy in both the rolled state and after annealing. In addition, stress-strain curves were obtained from (100)[001]-oriented crystals of iron and 3 and 5 pct Si-Fe to determine the effect of silicon on tensile properties. The dislocation substructure of the tensile specimens was also determined for Samples pulled to 2 and 10 pct elongation at room temperature for comparison with the substructures produced by rolling. 1) EXPERIMENTAL PROCEDURE Crystals with 3, 5, and 6.25 pct Si were prepared by annealing 0.012-in.-thick sheets of high-purity Si-Fe in purified argon at 1200°C to effect growth

Jan 1, 1965

By H. K. Birnbaum

The effect of 1ow-temperature stabilization anneals on the structure of the 0 phase Au-Cd alloys and on the diffusionless transformations observed in these alloys was examined by X-yay diffraction techniques. A phase separation in the ß-phase region was proposed to account for the experimenta1 results. The effects of quenching from elevated temperatures on the transformation behavior of these alloys were shown to be consistent with the proposed mechanism. IT has been shown that the high-temperature ß phase (CsCl structure) of the Au-Cd alloy system transforms to a phase having an orthorhombic (D2) ß&apos; structurel1-3 for compositions near 47.5 at. pct Cd and a tetragonal (4/m, m, m) ß" structure* in the vicinity of 50.0 at. pct Cd. Both transformations are diffusionless, crystallographically reversible, and occur on cooling at about 60° and 30°C respectively. The temperature interval from the beginning to the end of the transformation is of the order of 5°C in each case. Although the transformations are normally athermal, some of them have been reported to occur isothermally.= wechsler6,7 has shown that the effects of quenching a 49.0 at. pct Cd alloy from elevated temperatures are consistent with the retention of a nonequilibrium number of lattice vacancies. Annealing of these quench effects results in a broadening of the X-ray reflections.8 After a suitable quench, the 47.5 at. pct Cd alloy transforms to a phase having not the p&apos; orthorhombic structure but another structure which has properties similar to that of the ß" tetragonal structure.5.9 This change in the type of transformation has also been obtained after long anneals in the ß-phase region at about 70oC10 The present investigation was primarily concerned with the structural changes accompanying the above transformation phenomena. The change in transformation product and accompanying physical changes during an anneal in the ß phase have been termed stabilization effects. Experimental Procedure —The results reported in this investigation were obtained with the use of a Norelco diffractometer fitted with a temperature-controlled cryostat. The specimen temperature was controlled to better than ± 0.l°C during the measurements. CrKa radiation monochromated electronically with the use of a scintillation counter and pulse height analyzer was utilized. Specimens containing 47.5 and 50.0 at. pct Cd were prepared by sintering filings obtained from homogenized ingots of the proper alloy composition. (Gold of 99.999 pct purity and cadmium of 99.98 pct purity were used). All heat treatments were carried out with the specimens capsulated in vacuum ( < 10 % mm Hg) or in a He-H gas mixture. The quenching technique used in these experiments was to drop the pyrex capsule which contained the specimen from the annealing furnace into water, the temperature of which was controlled. The pyrex capsule shattered on contacting the water resulting in a relatively rapid quench. After the heat treatment, the specimens were mounted in the diffractometer and were left undisturbed in the diffractometer specimen holder during each sequence of measurements. EXPERIMENTAL RESULTS A) Low-Temperature Annealing—The transformations which were considered "normal" for these alloys were those obtained athermally during furnace cooling at approximately 50°C per hr after an elevated temperature anneal. Under these experimental conditions, the specimens were observed to transform to phases having structures whose diffraction patterns could be indexed as the ß&apos; orthorhombic structure for the 47.5 at. pct Cd and as the 0" tetragonal structure for the 50.0 at. pct Cd alloys. The transformation temperatures on cooling were approximately 60" and 30°C, respectively. Under the "normal" conditions both transformations were observed to go to completion, i.e., the entire volume of the ß phase was transformed to the product phase. In some specimens an extremely weak ß 110 reflection was observed at 20°C indicating that a small amount of retained ß was present. The effect of low-temperature annealing on the nature of the diffusionless transformations was examined for the 47.5 and 50.0 at, pct Cd alloy. The specimens were annealed in evacuated capsules at temperatures in the vicinity of 600°C (as specified in Table I) for 24 hr and were then cooled to 100°C at a rate of 50°C per hr. The specimens were then removed from the capsules and mounted in the diffractometer without allowing the specimen temperature to drop below 80°C. Annealing at the low temperatures was accomplished in the diffractometer by means of the cryostat which was mounted around the specimen. During the low-temperature anneals the lattice parameter, integral breadth of the reflections, and ratios of the integrated intensities of the fundamental and super lattice reflections for the 0 cubic phase were periodically determined. After annealing for the required time, the specimens were slowly cooled in the diffractometer and the diffraction patterns were recorded as a function of temperature. The specimens were cooled until the phase transformations were completed, following which the specimens were heated and diffraction

Jan 1, 1960

By M. E. Fine, A. A. Henderson

Investigation of the tensile properties of silver based aluminum alloy crystals was undertaken because it appeared attractive for studying strengthening effects due to Suzuki locking with minimum complication. Yield drops were observed in all alloy crystals (1, 2. 3. 4, and 6 at. pct Al) after strain aging at room temperature. No yield drops were found in similarly grown and tested silver crystals. The yield effects are attributed to Suzuki locking but the major portion of the solid solution strengthening to other mechanisms. INVESTIGATION of the tensile properties of single crystds of silver alloyed with aluminum was undertaken because it appeared to be a system in which segregation at stacking faults associated with partial dislocations1 would be the dominant factor in anchoring dislocations. First, silver and aluminum have closely similar atomic sizes and thus solute atom locking of a dislocation due to elastic interactions should be unimportant. Second, while both X-ray2 and thermodynamic3 investigations show short-range ordering in silver-based aluminum alloys, the degree of local order is quite small (X-ray measurements give v = EAB - 1/2(EAA + EBB) = - 0.025 ev and thermodynamic measurements give v r -0.007 ev) and should not be important in strengthening dilute alloys. Third, the stacking fault energy of silver is probably low (as indicated by the profusity of annealing twins) and is very likely diminished further and quite rapidly by aluminum additions since the A1-Ag phase diagram shows a stable hexagonal phase at only 25 at. pct Al. Also, a careful investigation in this laboratory4 has shown that the ratio of twin to normal grain boundaries in recrystallized alloys increases with aluminum content. Thus, with minimum complication from other factors, Ag-A1 alloys seem attractive for studying strengthening effects due to segregation at stacking faults of extended dislocations. EXPERIMENTAL METHOD Single crystals measuring 250 by 5 by 1.5 mm of pure Ag (99.99 pct) and Ag-A1 alloys (A1 of 99.999 pct purity) of nominal compositions* 1, 2, 3, 4, and 6 at. pct were grown in high-purity graphite molds from the melt under a dynamic vacuum (1 x l0-5 mm Hg). The technique consisted of moving a furnace having a hot zone (which melted about 0.5 cm of alloy) over a horizontal, evacuated quartz tube con- taining the mold and alloy at a rate of 3/8 in. per hr. Chemical analysis showed roughly the first inch of the crystal to be solute poor, the last inch solute rich; and the center section uniform in composition within the sensitivity of the analytical method (± 0.2 at. pct Al). The center section of the crystal was cut into five specimens. Gage lengths of reduced cross section, measuring from 1.5 to 2 cm in length, were mechanically introduced by means of jeweler&apos;s files and fine abrasive cloth with the crystal firmly held in polished steel guides. One-third of the cross section was then removed by etching and electro-polishing, the crystals were all subsequently annealed for several days at 850°C in a dynamic vacuum (<1 x 10-5 mm Hg) and furnace cooled to 200°C. The crystal orientations were determined using the usual back-reflection Laue technique. The Laue spots were sharp and of the same size as the incident beam. However, microscopic examination showed the crystals to contain substructures with subgrains of the order of a micron in diameter. The details of this substructure are presently under investigation. Tensile testing was done with a table model Instron using a cross-head speed of 0.002 in. per min. For testing at various temperatures the following media were used: 1) 415oK, hot ethylene glycol; 2) 296ºK, air, acetone, water; 3) 273ºK, ice water; 4) 258ºK, ethylene glycol "ice" in ethylene glycol; 5) 200°K, dry ice in acetone; 6) 77ºK, liquid nitrogen. EXPERIMENTAL RESULTS A) Yield Behavior—A portion of an interrupted stress-strain curve for a 6 at. pct A1 crystal of the indicated orientation tested at room temperature is shown in Fig. 1. Initially, at (a), there is a small, gradual yield drop of about 10 mg per sq mm2. However, on stopping the test, and aging for a few minutes at (b), a sharp yield drop is found. Aging for longer times at (c) and (dl results in larger yield drops (and larger AT&apos;S). At, defined in Fig. 1, is usually larger than the yield drop by about 20 pct; however, this increase in the lower yield is transient since extrapolations of the flow stress curves join as may be seen from Fig. 1. (Both Laue and low-angle scattering photographs revealed no evidence of precipitation in a strain-aged 6 at. pct A1 crystal.)

Jan 1, 1962

By Klaus-Peter M. Hanke

INTRODUCTION In early 1979 Jim Walter Resources, Inc. (JWR) of Brookwood, Alabama approached TMCI Construction, Inc (TMCI) to make a proposal on a program that involved the sinking of up to 10 ventilation shafts of approximately 6.7 m (22 ft) diameter and ranging in depth from 500 to 700 m (1650 to 2300 ft) for the JWR coal mines in Alabama. At this time TMCI was already constructing the first spiral underground bunker (capacity 2000 tons) in North America for the JWR organization at their No. 4 mine in Alabama. The TMCI proposal was based on the use of the mos modern large diameter shaft boring machine rather than sinking the shafts using the conventional drill blast-muck technique. The proposal was made based o: the experiences by the parent company, Thyssen Schachtbau, which has been using this type of machin in Germany for shaft boring since 1971. As a result of the TMCI proposal JWR issued a purchase order to TMCI for the construction of four 6.7 m (22 ft) diameter, concrete lined, unfurnished ventilation shafts ranging in depth from 500 to 700 (1650 to 2300 ft). An order was thus placed with WIRTH Machinen- and Bohrgeraete Fabrik GmbH, in Germany for the manufacture of a model 650/850 E/Sch "Schachtbohrmaschine" (Vertical Shaft Borer = V-mole which arrived on site in Alabama in early 1981. The first V-mole GSB 450/500 was introduced in Germany in 1971 and was capable of enlarging in one step a pre-drilled 1.2 m (4 ft) pilot hole to 4.5 - 5.0 m (14.7 - 16.4 ft). This machine has sunk 9 staple shafts and deepened one surface shaft for a total of 2360 m (7740 ft) of shafts. On the last shaft boring operation in 1978 the machine was converted as an experiment to drill without a pilot hol using a hydraulic pumping system to remove the cutting debris. A second generation machine, the SB VI 500/650, was introduced in 1977 for enlarging the pilot hole to a range of 5.0 - 6.5 m (16.4 - 21.3 ft) diameter. This machine is still in operation and has already drilled well over 2000 m (6500 ft) of shaft. The third generation of V-mole, the SB VII 650/85( for diameters from 6.5 to 8.5 m (21.3 to 27.9 ft) was: commissioned in May 1980 and has been used for two surface shaft deepenings totalling 606 m (1990 ft) with another scheduled for 1982. The main advantages favouring the use of such V-moles were identified as: 1) A reduction in manpower to the crew required in a conventional shaft sinking operation. 2) A considerable reduction in time to complete a shaft compared to conventional techniques. 3) The use of the V-mole eliminates many of the hazards encountered in conventional sinking. Based on the successful performance of the first three V-moles in Germany, Thyssen Schachtbau decided to employ this principle abroad. In 1980 a second machine of the third generation was built and is now operated by TMCI Construction, Inc. in Alabama. The first shaft was completed at the end of 1981 and this paper describes the method of operation including some unique aspects not attempted on prior V-mole operations and some of the statistics arising out of the experiences during the first shaft boring operation. THE NO. 7 MINE FAN SHAFT SITE Jim Walter Resources, Inc. was formed in 1970 to exploit the coal field in Alabama on the southern tip of the Appalachian coal field. The coal reserves amount to around 650 million tons of mainly good quality coking coal of which about 350 million tons are to be extracted over the next 30 years. Shaft sinking and preparatory work began in 1972, and at present 6 mines are producing around 5.4 million t.p.a. Annual production is to expand to 10 million t.p.a. as soon as possible, and the ventilation shafts to be sunk by TMCI play a vital role towards attaining this goal. The first shaft site is located at the No.7 mine, near Brookwood, Alabama. The actual location of the shaft relative to the production shafts is shown on the mine plan (Fig. 1), which also shows the room-and-pillar extraction system used at present. The mine plan further shows the conveyor route used for the muck removal. The geological survey showed that the strata consisted of horizontal layers of mainly sandstone, sandy shale and shale interspersed with several coal seams. The seam being extracted at the No. 7 mine is a combined seam made up of the Blue Creek and Mary Lee seams at a depth of 513 m (1682 ft) and having an average seam thickness of about 2 m (6 ft). At the beginning of September 1980 the surface site preparation and pre-grouting work was completed by JWR, and TMCI was able to commence with Stage I of the shaft sinking program - the drilling of the pilot hole.

Jan 1, 1982

By M. O. Abo-el Fotoh, J. B. Mitchell, J. E. Dorn

The effect of strain rate and temperature on the tensile flow stress of a polycrystalline bcc alloy of magnesium containing 14 wt pct Li and 1.5 wt pct Al was investigated for strain rates of 3.13 x lom5 to 3.13 x 10-3 per sec over the range from 20° to 300°K. From about 180° to 300°K the alloy exhibited an ather-ma1 deformation behavior where the flow stress was independent of strain rate and increased only slightly with decreasing temperature. At lower temperatures the flow stress was strongly strain-rate- and temperature-dependent, characteristic of deformations controlled by thermally activated mechmzisms. The activation volume for thermally activated plastic defornzation was between 5 and 30 cu Burgers vectors, independent of plastic strain. This low-temperature thermally activated deformation behavior was found lo be in satisfactory agreement with the theoretical dictates of the Dorn-Rajnak1 formulation of the Peierls mechanism where deformation is controlled by the rate of nucleation of pairs of dislocation kinks over the Peierls energy barriers. SEVERAL studies of the low-temperature thermally activated deformation of bcc metals and alloys (molybdenum,1 tantalum,1 Fe-2 pct Mn,2 Fe-11 pct MO,3 and AgMg4) have revealed that the strain rate is controlled by the activation of dislocations over the Peierls-Nabarro energy hills. Although there is some uncertainty as to the nature and effect of solute atom-dislocation interactions during low-temperature deformation of bcc metals, it has been concluded by Dorn and Rajnak,1 Conrad,1 and Christian and Masters6 among others that overcoming the Peierls-Nabarro stress which arises from the variations in bond energies of atoms in the dislocation core as it is displaced is the probable mechanism controlling low-temperature deformation. The purpose of this research was to investigate the low-temperature plastic deformation of the bcc alloy Mg-14 wt pct Li-1.5 wt pct A1 to determine if the behavior of this alkali metal alloy might be analogous to that for other bcc metals. This alloy was selected because of its availability and its current industrial importance as a lightweight material for aircraft and aerospace applications. I) EXPERIMENTAL PROCEDURE Polycrystalline tensile specimens having cylindrical gage sections 2 in. long by 0.2 in. in diam were machined from as-received alloy sheet stock of Mg-14 wt pct Li-1.5 wt pct Al. Specimens were annealed in an argon atmosphere at 423°K for 4 hr and maintained in a kerosene bath together with the sheet stock to prevent corrosion. The resulting specimen microstructure consisted of a coarse uniform dispersion of incoherent precipitate MgLi2Al particles7 in a bcc 0 phase matrix having an average grain size of 150 p. Prior to testing the specimens were chemically polished in dilute hydrochloric acid. Comparison of tensile properties and microstructures of specimens cut from center and edge sections of the sheet stock revealed no effects of inhomogeneities in the sheet material. Tensile tests were performed on an Instron machine at crosshead speeds corresponding to tensile strain rates of 1.56 x 10-5 and 1.56 x 10"3 per sec. Stresses were determined to ±2 x 106 dynes per sq cm and strains to within ±0.0001. Average values of shear stress t and shear strain y reported were taken as one half the tensile stress and three halves the tensile strain, respectively. Flow stresses were taken at 0.05 pct strain offset. Test temperatures down to 77°K were obtained by immersing the specimens in constant-temperature baths. Lower-temperature tests were performed in a liquid helium cryostat to within ±2°K of the reported values. Prior to testing at the various temperatures and strain rates all specimens were prestrained at 2 35°K at a shear strain rate of 3.13 x 10-5 per sec to a stress level of 0.606 x 10&apos; dynes per sq cm to obtain a uniform initial state. Additional tests were made to determine the effect of changes in strain rate and strain on the flow stress by rapidly changing the crosshead motion during testing. Shear moduli of elasticity, needed for analyses of the data, were obtained at several temperatures by a common technique of determining the resonant frequencies of vibrations of rectangular test specimens. 11) EXPERIMENTAL RESULTS Fig. 1 shows the experimentally determined flow stress vs temperature for two strain rates. Two distinct regions of behavior are evident. Below about 180°K the strong increase in flow stress with increased strain rate and decreasing temperature indicates that deformation is controlled by a thermally activated dislocation mechanism. At higher temperatures an athermal region is evident where the flow stress is independent of strain rate and only slightly dependent on temperature. The applied stress t to cause plastic flow was separated into two components:

Jan 1, 1969

By H. F. Kendall, J. H. Ffolliott

MANY papers and reports have been devoted to the geology and ore deposits of the Ducktown district, Tennessee, especially the complete report by W. H. Emmons and F. B. Laney, published as Professional Paper 139, by the U. S. Geological Survey. The present paper discusses the work of the geological organization of the Tennessee Copper Co., which is based on the field work of the above paper and the consulting work of W. H. Emmons. The Ducktown basin lies in the southeastern corner of Tennessee and extends a short distance into Georgia and North Carolina. All productive mines are contained in an area of 15 sq. mi. in the center of this basin, which is an undulating plateau at an elevation of 1650 to 1800 ft. above sea level. It is surrounded by the relatively high mountains of the southern Appalachian region. The rocks are of early Cambrian age. Deposition of the ores probably took place during the latter part of the Paleozoic era. The ore deposits are rudely tabular to lens-shaped bodies of massive sulfide, varying from a few feet to over 200 ft. in width. In general they all strike northeast and dip southeast at angles from 45° to 70°. Locally, where affected by folding and faulting, the variations in dip may be even greater. The lodes usually are parallel at distances of from one-half to one mile measured normal to the strike. The deposits are a replacement of a fairly continuous bed or a series of disconnected limestone lenses, highly folded and somewhat faulted, which probably represent the same stratigraphic horizon.

Jan 1, 1933

By George A. Miller

THE outstanding characteristic of the American business man is that he likes to run his own business his own way, without any interference from his wife, his friends, his bankers, and least of all from his government. The oil man, like the miner, is an American business man in which this special characteristic is even more pronounced. It may be because he has been an explorer and is more nearly like those pioneering Americans who explored, developed, and built these United States.

Jan 1, 1944

By J. W. Byrkit

Design features and operating methods at the new Ajo smelter are described in detail. Successful operation of a novel method of handling and charging wet concentrates to a deep bath type reverberatory furnace contribute to the daily production of 200 tons of anodes with good results from the standpoint of both metallurgy and economy. THE New Cornelia Branch of the Phelps Dodge Corp. is located at Ajo, Ariz. Large scale mining operations were started at Ajo in 1917, when a 5000 ton leaching plant was put in service to treat the copper carbonate ore that overlaid the sulphide ore-body. In 1924 a 5000 ton flotation plant was built to treat the sulphide ore and the leaching operation was abandoned a few years later. Changes in practice and additions to plant facilities have resulted in a gradual increase in the milling rate which now approaches 30,000 tons daily. Prior to the erection of the Ajo smelter, flotation concentrate was shipped by rail to Douglas, Ariz, where it was treated in the Phelps Dodge smelter. Construction of a one reverberatory furnace smelter to produce an average of about 200 tons per day of copper anodes at Ajo was started early in 1949. Initial heating of the reverberatory furnace was begun on June 21, 1950. Charging the furnace was started on july 8, and the first anodes were cast on July 14. Neither the anode furnace nor the reverberatory furnace has cooled since the initial firing. Fig. 1 is a photograph of the new smelter. Built primarily to eliminate the &apos;300 mile haul of concentrate to the Douglas plant, the new smelter was designed to treat the Ajo concentrate, with a minimum of capital investment. A novel, and relatively simple, method of concentrate handling and furnace charging made unnecessary the installation and operation of expensive storage facilities and reclaiming equipment, and obviated the necessity of holding in storage large quantities of copper-bearing materials. (Patents are pending in the United States and abroad on the Ajo process.) In the selection and arrangement of equipment, consideration was given to the full utilization of all smelting facilities, reducing the amount of idle equipment to a minimum. The layout of the smelter is shown in Fig. 2. The important problem of internal transportation was minimized by arranging the reverberatory furnace, converters, and anode furnace in a compact group and providing storage bins inside the smelter building, within reach of overhead cranes, for fluxing materials and other supplies needed in the daily operation. This can be seen in the sectional view of the smelter given in Fig. 3. Incorporated in the design were many innovations in smelting equipment intended to facilitate operations and effect economies in maintenance expense and manpower requirements. Table I gives operating data of the entire plant. Metallurgy The metallurgical practice at Ajo is based essentially upon the use of a single, deep bath reverberatory furnace for smelting wet concentrate, without concentrate storage facilities. The large reservoir of slag and matte maintained in the furnace serves to equalize, to some extent, the day to day variations in the nature and grade of concentrate and permits

Jan 1, 1954

By Clinton H. Crane

DR. TILNEY, the great expert on the study of the development of the brain of human beings and animals, tells us that the greatest difference between the human brain and the brain of animals is that man alone has shown evidence of being able to predict the future. Just why he throws overboard the busy bee who lays up honey for the winter, the squirrel who gathers nuts, and the humble ant, I do not know. At any rate, it is nice to be assured by an authority that we have this power of prophecy. My own experience with attempting to prophesy the future has convinced me that our only possibility of being good prophets is to be good students of history.

Jan 1, 1940

By H. P. Greenwald

IN the year just passed the Coal Division&apos;s Committee on Rock-Dusting reviewed the status of this safety measure in American coal mines and prepared a paper thereon which will be presented at the February meeting of the Institute. This paper supplements one appearing in Vol. 139 of the "Transactions," page 87 (1940). Because that paper will be issued soon, only a summary is given herein.

Jan 1, 1944

By G. C. Trevorrow

STRIP mining during 1943 increased considerably with further extension of mechanical loading in mines already partly mechanized; with the considerable introduction of mechanical loading into hand-loading mines; and with improvements in the use of loading equipment. Extension of the use of machinery both in strip mining and underground is due to reduction in labor supply and increased cost of labor, together with the increased demand for coal during the period of labor shortage.

Jan 1, 1944

By AIME AIME

WITHOUT frills, but with an admirable program of technical papers and discussion, many opportunities for social contact, and all New York for a playground, the 142d Meeting of the Institute will make the Engineering Societies Building a lively place from Feb. 20 to 23. Prices are down, even in New York. Come and forget the depression listening to the stories of old friends. Hear at first hand what is going on in your professional world. The fare is varied, of wide appeal. The program on the opposite page has been arranged carefully to minimize conflicts between the subjects in which you are interested. If it is not possible to come for all four days, check over the sessions that are most important to you. No changes in the scheduling are likely.

Jan 1, 1933

By W. G. Jewitt

YELLOWKNIFE, the most northerly Canadian gold mining district, is once more in the throes of a boom. Touched off by spectacular and well-publicized diamond-drilling results on the property of Giant Yellowknife Gold Mines, Ltd., mining companies and the general public are competing for mining claims and for the shares of companies owning mining claims in the area, with little regard for values. Such a stock-market boom has various unfortunate consequences but undoubtedly one beneficial result is that considerable amounts of money are made available for serious development. The Yellowknife mining area lies on the north shore of Great Slave Lake, in the Northwest Territories, at a latitude of approximately 62°30&apos; north. The topography is a low-relief phase of that usual in the Canadian Laurentian shield. Roughly, one third of the surface is lake-covered, one third muskeg or overburden, and one third is bare

Jan 1, 1944

By Odmund Ljone

FAR north of the Arctic Circle is a totally industrial community which until 1945 could not boast a single specimen of the rat family, and where today you will be awarded a bottle of fine cognac for every rat-dead or alive. Amazing but true, the spot is Longyear City, the Norwegian mining town on the arctic island of Spitzbergen. Perhaps you have also heard of the town built on soil that never thaws, where huge blocks of ice must be melted to fill the city&apos;s fresh water reservoirs, and where the Far North dictates a way of life all its own. Here, coal is king and men must work hard for their "black gold." Spitzbergen is a rough, tough piece of Norway, made up of a half dozen isolated islands between 74 and 81 degrees north latitude. Covering twice the area of Belgium, they are home to

Jan 1, 1948

By Rich Akerman

as 1866, I wish to assure both these gentlemen that I had not seen the section when I designed mine, :md even if I had, I should not have then dared to put it forth as a standard for English rail makers; tind the soundness of my opinion has a simple but conclusive proof in the statement made concerning the extra price which was at that time required for their production. I need not say that I highly approve of the original Welch section, for it is in principle similar to the design which I made ufteen yeam subsequently; and from a professional point of view I would fully concecle to Mr. Welch the credit of first designing the modern steel-rail section. From com- mercial, matter of tict, and practical point of view, he was, however, before his time by many years; or to put it in another way, rail making was ten years behind its time when the new metal steel was first introduced for rails. If his design has been incorrectly identified with my name (as the sections are similar in principle, though they differ in thickness of flange and web), I beg to say (1st) that I much regret the misun- Understanding which has arisen through no fault of niine, aud (2d) that no confusion has been intentionally created by me. It is a pity that the section designed so long ago has not been made public at an earlier date, as it would make a really goal stand- and pattern, anil even now be quite equal to present requirements. In conclusion, I wish to say that I have never desired to claim any invention or novelty by the publication of my sections; they Were put forth as being such as English railmakers could and would produce at the ordinary market. price, and as being the best and most suitable to be so obtained. Had Mr. Welch or Mr. Holley put forward theirs ten or fifteen years ago, I should have been the first to recommend theru. In fact I should have been glad to see their narnes associated with rail patterns in their own country, in the same way as mine has been. PROFESSOR RICH. AKERMAN, STOCKHOLM, SWEDEN: i AGREE with your (Mr. Sandberg&apos;s) views that it is too early yet to stipulate only one definite chemical composition in the rails. Such a stipulation, I think, might he justified, if it were not for the manganese; but this metal changes the properties of the iron aud steel in tho same direc- tion ae carbon, silicon. and phosphorus, by increasing its tensile strength, stiffness, hardness, and brittleaess. If the iron and steel does not only contain carbon and manganese but also phosphorus,

Jan 1, 1881