Search Documents

By Albert D. Pernichele, Wayne C. Smith

Both water pollution and proposed solid waste disposal regulations have a definite effect on the copper leaching industry and some of the major factors affecting the industry are discussed in this paper. New developments of the NPDES are discussed with emphasis on the ‘toxic’ or priority pollutants, and EPA’s philosophy on the control of these pollutants. The protection of groundwater is the prime aim of RCRA through solid/hazardous waste management. Some of the major elements of the RCRA regulations that will effect the copper leaching industry are discussed.

Jan 1, 1980

By W. E. Newell

The basic principles and assumptions involved in D. L. White's solution5 for ultrasonic wave amplification in piezoelectric semiconductors are summarized. If the gain per unit length is maximized at each frequency without regard to the drift-field power density, the gain increases linearly with frequency. Therefore it would seem that very high gain is possible for frequencies in the hundreds of megacycles. However, with present materials the resulting drift-field power density is so large that cooling would be a major problem. For this reason it is more realistic to judge the capabilities of an ultrasonic amplifier in terms of the gain that is possible with a specified power density. In this case the gain at high frequencies does not increase but decreases more rapidly than l/f. The calculation of the gain us frequency at a fixed power level involves the repeated solution of a cubic equation and is therefore tedious. For the purpose of comparing different materials, sufficient accuracy can be obtained from an approximate solution which may easily be plotted as three straight lines on logarithmic graph paper. This method is used to compare the Performances of CdS, CdSe, ZnO, and GaAs. At a power density of 10 watts per cu cm, the first three give maximum gains of 60 to 80 db per cm in the vicinity of 60 megacycles. At the same power density, GaAs has a maximum gain of about 7 db per cm near 150 megacycles. Although an increase in mobility usually increases the gain for a specified power density, it is shown that there is an optimum mobility above which the gain decreases. An approximate expression for the optimum mobility is established. It is well-known that the interaction between charged particles and an electromagnetic wave can be used to amplify the electromagnetic wave. In the conventional traveling-wave tube, electrons in a vacuum are caused to move at a velocity slightly greater than the wave velocity, thereby coupling energy into the wave.' In principle, the same effect would be evident in a solid except that repeated collisions prevent the electrons from attaining a velocity greater than that of an electromagnetic wave. However, the drift velocity of electrons can be made to exceed the velocity of an acoustic wave in a solid. In 1956, weinreich2 noted that the deformation potential provided one means of coupling energy from drifting electrons into an acoustic wave, but the effect was too small to be of any practical importance. It was not until 1961 that White and Hutson demonstrated that the piezoelectric effect provided a strong enough coupling to give appreciable amplification of an ultrasonic wave and awakened wide interest in electron-phonon interactions. Qualitatively the effect may be described as follows. An acoustic wave propagating through a piezoelectric material is accompanied by an electric-field wave. If the vibrations are properly oriented with respect to the crystal axes of a piezoelectric semiconductor, the local electric fields are axially directed and cause bunching of the charged carriers. If the drift velocity of these carriers is less than the velocity of sound, they tend to be dragged along by the acoustic wave. This electroacoustic effect results in a net potential appearing across the material and in attenuation of the acoustic wave. On the other hand, if the drift velocity exceeds the velocity of sound, energy is coupled from the carriers to the acoustic wave and amplification results. Related effects which are being investigated include ultrasonic amplification in semimetals6-' and semi-conductor, and current saturation in piezoelectric semiconductors.'4-17 There are various problems which hinder the immediate application of ultrasonic amplification in a practical device. First, there are the traditional problems encountered in the design of acoustic delay lines: attenuation in the electromechanical transducers, reflected waves (which can lead to self-oscillation in an amplifying device), mechanical tolerances necessary to maintain phase coherence, and so forth. Second, there is the problem of selecting the best material from among the various piezoelectric semiconductors as they become available in single-crystal form with a wide choice of characteristics. This paper deals with the second problem and shows that the most realistic way of comparing materials is in terms of the gain which can be obtained without exceeding a

Jan 1, 1964

By M. S. Burton, J. E. Ritter

The sessile-drop technique was employed to study the effect of atmosphere and alloy additions of titanium and chromium on the surface tension and contact angle of nickel on sapphire substrates at 1500oC. Shear tests were conducted on the solidified sessile drops. The liquid-gas surface tension of pure nickel on sapphire was found to be 1747 ergs per sq cm, with a contact angle of 109.6 deg. The surface tension and contact angle were not affected significantly by the four atmospheres, vacuum, impure argon, pure argon, and pure hydrogen. Small additions of titanium and chromium decreased the contact angle and for the same alloy content, contact angles were lower in pure argon than in pure hydrogen. On the basis of shear-test results , the most probable cause for adhesion in the Ni-Al2O system is the formation of NiO:Al2O3 spinel at the interface; in the titanium alloy-Al2O3 system adhesion is thought to be due to a mechanical interlocking effect; in the chromium alloy-Al2O3 system adhesion is believed to be the result of solid-solution formation involving Cr2O3 and Al2O3 at the interface. In the last few years there has been considerable interest in reinforcing metals with ceramic whiskers. It has been postulated that, by reinforcing nickel with sapphire whiskers, high-temperature strengths su- perior to those of the best current nickel alloys can be achieved.' To fabricate a whisker-metal composite having optimum density and strength, understanding of wettability and adherence in the system is of prime importance. Although there has been some previous research in this a a need for further studies has been cited4-8 to understand better the effects of impurities, alloys additions, and atmosphere on the wetting and bonding of metals to metal oxides. The purpose of this research was to investigate the factors involved in the wetting and adherence of nickel/nickel alloys to sapphire (single-crystal a Al2O3). Sessile-drop experiments were conducted in vacuum, impure argon, pure argon, and pure hydrogen, to determine the effect of atmosphere on the contact angle of the metals on sapphire, and the liquid-gas surface tension of pure nickel. The solidified sessile drops were sheared from the sapphire substrate to measure the bond strength between the metal and ceramic. The alloy additions chosen were titanium and chromium since both enhance the wetting of nickel on sapphire.2, 3c Also, titanium is commonly used when brazing metal-to-ceramic seals to improve adherence. Since chromium forms an oxide that is completely soluble in sapphire, it was thought that the oxide could serve as a transition phase to promote bonding between the Ni-Cr alloy and sapphire. I) EXPERIMENTAL APPARATUS AND PROCEDURE The sessile-drop apparatus was a horizontal furnace, with an induction-heated, cylindrical molybdenum susceptor in a water-cooled Pyrex chamber. This apparatus was patterned after that of Williams and Nielsen.7 A flat Pyrex window at each end of the furnace allowed temperature measurements to be made at one

Jan 1, 1968

By T. H. Alden

Using alternating tension-compression straining, the hardening of magnesium oxide single crystals was studied up to large stresses and strains. At 0.25 pct plastic strain amplitude, the hardening curve is approximately linear with slope 25,000 psi from the shear yield stress, 7 to 8000 psi, to 35,000psi. Above this stress, the slope decreases. The strain hardening behavior of MgO is considered qualitatively similar to that of metal single crystals. The relatively high stress attainable by strain hardening is associated apparently with the high yield stress on the cross-slip system, (001) <110>. Cleavage fracture during testing is uncommon. It is argued that the centers of high internal stress at glide band intersections, at which cracks tend to nucleate, are dispersed by cyclic strain. Special features of the glide band structure produced by cyclic strain and revealed by dislocation etch pits, support this view. Strain hardened MgO has mechanical properties greatly superior to the as-received material: yield stress, greater than 100,000 psi; elongation to fracture about 1 pct. A material is said to strain harden if the yield stress increases with an increment of plastic strain. This definition is usually applied for straining done in one direction, but is also applicable when the strain direction is periodically reversed, Fig. 1. For certain metal single crystals, data are available which permit a comparison of the hardening behavior for cyclic straining and for tension straining.&apos;-4 With certain qualifications, these data show that the same processes of hardening are operative in each type of test.5 Despite this fact, the importance of the technique is not immediately evident, although tension-compression studies of the common metals appear to suggest some deficiencies in theories of strain hardening developed exclusively on the basis of tensile tests. However, a recent observation suggests that the cyclic straining method may be very useful for studying semibrittle crystals in which large plastic strains are not accessible in unidirectional testing. The observation is that zinc crystals, when strained in tension-compression at -52°C, do not fail by cleavage at low stress (-500 psi)6 as they do in tension, but harden to a limiting stress of more than 5000 psi over a total plastic strain of about 600 pct.2 An important characteristic of the behavior of zinc crystals is the high stress, relative to the yield stress, attainable by strain hardening. By comparison, the hardening of aluminum single crystals tested by an identical technique saturates at 1100 psi. This difference is best explained by the cross-slip hypothesis of dynamic recovery.7,8 In zinc, cross slip is difficult because of the high yield stress for glide on planes other than the basal plane in the < 1120 > zone. The present work was undertaken in order to test whether these methods and ideas are applicable to other materials. Magnesium oxide single crystals, in common with most crystals of the rock-salt structure, deform plastically but fail by cleavage after a small strain when tested in tension. It was hoped that larger strains would be attained using tension-compression. There is, in addition, evidence 8a which shows that slip on the probable cross system, (001) < 110>, is difficult in magnesium oxide; it may therefore be possible to attain high stresses by strain hardening. 1) EXPERIMENTAL PROCEDURE Experimental methods used in this study were based in part on techniques reported in papers of Stokes, Johnston, and Li.&apos; MgO blocks, purchased from Norton Co., were used without further annealing. Specimens were cleaved to dimensions approximately 0.125 in. sq and 1 in. in length. The gage section, formed by chemical polishing, was sprinkled with 280 mesh silicon carbide particles in order to introduce fresh dislocations. The crystals were then cemented into cylindrical aluminum adapters and clamped in an Instron testing machine. One of two alternating straining programs was used. In the first, total cross-head travel was established and increased in steps after various numbers of cycles. In the second, a capacitance gage was used to directly measure the elongation of the specimen and the crosshead was controlled so as to keep the plastic strain amplitude constant. The straining was always symmetrical with respect to the initial, zero strain condition. While both procedures produce strain hardening, only the latter permits a measure of the total plastic strain so that hardening curves may be drawn. Constant plastic strain amplitude tests were done

Jan 1, 1963

By Fred Witt, Milton Schwartz

ESTABLISHED methods for obtaining quantitative pole figures for flat sheets1"5 can be extended to apply to thin films on a substrate. The mode of scanning the sample is exactly the same as described in the references? but consideration is given to the fact that the scattered X-ray intensities are due to both the thin film and its substrate with appropriate attenuation factors. The purpose of this paper is to describe a method to obtain the scattered intensities from the film alone for subsequent pole-figure determinations. Fig. 1 shows the four possible general positions of the film (f) and its substrate (s) with respect to the incident X-ray beam (I,). In this paper it will be assumed that the plane of the sample is normal to the plane of the diffractometer. In the diagrams the line jV is the normal to the flat sample and the line P is the trace of the diffracting crystallographic planes in the plane of the diffractometer. The angle of tilt, a, is the positive acute angle measured from the line N to the line P; if this angle is measured clockwise then a is said to be in the positive a region; if this angle is measured counterclockwise then a is said to be in the negative a region. For the reflection cases, the total scattered intensity, at the proper Bragg angle for a particular set of planes, is due to that scattered by the film Vf) and that scattered by the substrate. The beam incident on

Jan 1, 1967

By Juhani Pulkkinen, Pekka Lappalainen

Preplaced cable bolts - fully grouted old hoisting cables or stress relieved steel strands - have been used succesfully to pre- reinforce ore contact zones and pillars in sublevel stoping at Outo- kumpu Oy mines for ten years. The purpose is to make open stoping methods possible even in "poor&apos;&apos; conditions and to decrease waste rock dilution. Since 1971 more than 120 km cable bolting has been done, and plans for this year in five mines amount to 33 km. In order to understand the function of cable bolt, pull-out tests have been done both in the laboratory and in situ. Bond strength between cable and cement is highly dependent on cable structure and cable surface dirtiness. Steel cables with steel core and rough surface structure have highest bond strength ( 6 MP~). A cable bolt is a friction bolt. After losing its peak bond strength - after starting to move - a cable bolt still has a high loading capacity due to the friction caused by the uneven surface of the cable. Cable bolting is done before actual stoping from existing drifts, sublevel drifts, e.g. or from special bolting drifts. In general stress relieved steel strands are used; 2 x 15.2 mm dia per hole. FEM or BEM calculation is utilized in cable bolting design. Bolts 2 are in fan shape, 10 m ... 50 m long and are spaced 1/20 m ... 1/50 m2 at stope walls. Pretensioning of cable is not needed, when bolting is done before rock deformations. Bolting costs vary between 0.3 USD ... 1.0 USD/ore ton. In the beginning only manual cable installing technique bras used. Now bolting can be done as fully mechanized with the developed cable bolting machine; i.e. drilling of the hole, installing and cutting of cables and grouting of hole.

Jan 1, 1983

By M. Cepak, K. Donovan, W. G. Pariseau

This paper examines the difficulties of applying the finite element (FE) method of analysis to quantitative design of cable bolt systems. Cable bolt systems are in general use for ground control in VCR (Vertical Crater Retreat) topes throughout the world. However, despite their widespread use and importance, design of cable bolt systems is highly subjective. Two difficulties with the FE approach are examined: (i) the use of standard elements with a high aspect ratio (slender elements) to represent bolts, and (ii) the influence of cable bolts on hanging wall stability of a VCR study stope. Analysis results indicate that the use of slender elements for bolts is practical in large scale finite element analyses of VCR stopes. There are significant advantages in this approach to the engineering design of cable bolt systems in underground mining.

Jan 1, 1984

By J. L. Bruce, G. W. Nicolson

ThE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydro-thern~ally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CeMent and Concrete Linings During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, howcver, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 11\2 pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with 12 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concretc and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1949

By A. M. Gaudin

A GREAT number of hypotheses has been advanced to explain the complex phenomena that are encountered in flotation. In the days of bulk-oil flotation, when a large quantity of oil was employed, it was observed that the oil-mineral aggregate floated above the ore-pulp because of its lesser density. With the advent of froth-flotation this phase of the theory had to be modified to take into account the presence of air bubbles. The reason why the mineral-bearing froth of today rises to the top of flotation cells is, of course, because the air-mineral aggregate, with whatever reagent may be associated with it, is lighter than the pulp. In an attempt to explain froth-flotation the fact has been emphasized that certain minerals are wetted and therefore remain in water; while others are not wetted and therefore become associated in preference with air. Such an "explanation" does not explain facts, it merely states them; for instance, it does not explain why minerals are wetted under some circumstances and not wetted under others. Going somewhat further, the wetting or nonwetting of minerals by water has been ascribed&apos; to differences in the angles of contact between oil droplets and mineral surface at the surface of the minerals. This explanation, however, was abandoned when soluble flotation reagents came to replace the so-called "insoluble" reagents. Another theory, sponsored about 10 years ago by Ralston,2 involves the effects of electric charges at the surface of the minerals particles and air bubbles. This theory, unfortunately, was not developed as fully as it seems desirable.

Jan 1, 1927

By C. M. Schwartz, J. R. Bridge, D. A. Vaughan

THERMAL expansion coefficients of a uranium were originally reported&apos; on the basis of X-ray diffraction measurement of lattice constants at 25°, 300°, and 650°C. These data have been reproduced by Katz and Rabinowitch.&apos; CuK radiation had been used in this work, with consequent crowding of the patterns. Considerable overlap of the back-reflection lines was observed as the temperature was raised. Subsequent reexamination of the data led to the conclusion that errors had resulted from failure to obtain unequivocal indexing of the high angle reflections at elevated temperatures. The measurements have been repeated, using FeK radiation, which provided sufficient dispersion to assure proper indexing of the reflections, at each temperature level. The unit cell dimensions were re-determined at ten temperatures, from 25" to 650°C. Schuch and Laquer easured the macroscopic contraction from room temperature down to —253°C, and reported a negative value from —210" to —253°C; they suggested the possibility of the occurrence of a phase change. In the present work, the lattice constants of uranium have been measured down to —253°C, to test this hypothesis. Filings were prepared from a single piece of pure uranium bar stock. They were carefully cleaned with a magnet and pickled in nitric acid to remove traces of iron from the file. They were then annealed at 600°C in a sealed evacuated silica tube. The annealed filings were pickled in strong nitric acid to remove any oxide layer, washed in water and alcohol, quickly dried, and sealed in evacuated thin-walled silica capillary tubes. If properly sealed, the sample could be heated to the a-ß transforination temperature without significant buildup of the diffraction pattern of oxide. The high temperature X-ray diffraction camera was modified from the design of Hume-Rothery and Reynolds.&apos; The thermocouple used to record the specimen temperature was calibrated from lattice-constant measurements of a standard silver specimen, using the Hume-Rothery and Reynolds values for silver over the temperature range from 25" to 700°C. Temperatures were reproducible to 210°C. Temperatures to —210°C were attained by passing precooled gas over the sample. The gas from the cooling train was directed over the sample capillary tube and thermocouple by means of a chimney of 1-mil polystyrene. The 36-gage Cu-constantan thermocouple had been calibrated by

Jan 1, 1957

By William P. Blake

It is scarcely necessary to point out the important functions of water in the mining operations of man, especially in the State of California, where sluicing and hydraulic mining have been practiced on such a grand scale as to arouse the opposition of the agricultural interests. But the role which water and ice have played in mining or excavating on their own account is not so apparent. The alluvions of existing rivers, and the higher gravel-beds left by ancient streams, are doubtless the result of running water; but how far these gravelly materials owe their origin primarily as rocky debris and fragments of veins to glacial erosion, it is difficult .to determine. Yet we see on every side in our higher mountains unmistakable evidences of the cutting, crushing and eroding effects of glacial ice. We note that mountain-summits have been reduced in height and shaped into rounded and dome-like summits. We know that the general contour of the hills of New England, of the Highlands of the Hudson, and of the mountains of northern New Jersey, is due to glacial carving. The same is true of the Laurentian hills of Canada and of the mountains of all northern regions. And we recognize in the vast deposits of so-called " drift," which are spread out over the surface of the northern States, the chips and debris from the glacial workshops. Thus we cannot avoid the conclusion that there was an enormous amount of cutting and excavating in glacial times, and that vast quantities of veinmaterial and of ores and metals must have been liberated by ice-action.

Jan 1, 1900

By S. F. Emmons

There is, in the southern part of the State of Illinois, a series of deposits of fluorspar and galena in which the former mineral occurs on a scale of magnitude unequalled, so far as I know, in any other part of the world. In June, 1891, 1 had an opportunity of visiting the region of their principal development, near Rosiclare, Hardin county, Ill., and examined such of the mines in the vicinity as were accessible at that time. A very large proportion of the mining shafts that had been sunk in this region were unfortunately abandoned for the time being, and full of water. Moreover, detailed maps of the region are unattainable, no surveys having been made there, apparently, since the original land-surveys&apos; of the early part of the century. In spite of these disadvantages I was enabled, in the few days at my disposal, to ascertain with sufficient accuracy certain facts not hitherto published with regard to these deposits, which seem worthy the attention of the members of the Institute. Before proceeding to a description of the deposits in question, I will give a brief abstract of the little historical and geological information hearing directly or indirectly upon them, which I have been able to find in existing publications. Historical. That the mineral was known to the Indians, is proved by the discovery, in some of the pre-historic mounds of the region,* of fluorspar, shaped into ornaments. The earliest scientific mention of its occurrence is found in the first volume of the American Journal of Science (1818+), which describes specimens obtained in the vicinity of Shawneetown by Mr. Joseph Baldwin. Similar notices appear in the same journal in 1820 and 1821, but without mention of the exact locality. They remark on the fetid odor which characterizes the mineral and its association with galena. Schoolcraft, as early as 1819, note: the occurrence of fluate of

Jan 1, 1893

By D. W. Smith

The beta solid solution phases of the systems copper-zinc, copper-aluminum, copper-tin and silver-zinc are structurally analogous.&apos; R. F. Mehl and 0. T. Marzke2 have shown that the a phase upon segregating from the 6 phase in the system copper-zinc takes the form of needles lying parallel to a [Ill] direction or some similar direction, such as [556], of the parent solid solution, and that the a phase upon segregating from the ß phase in the system copper-aluminum also takes the form of needles. By analogy they assume that in this case also the segregate needles lie parallel to the [ill] or [556] direction in the ß lattice. The purpose of this investigation is to determine whether the structures resulting from segregation of the a phases from the respective ß phases of the systems copper-tin and silver-zinc are analogous to those obtained by Mehl and Marzke in the systems copper-zinc and copper-aluminum. Segregation of the a Phase from the ß Phase in the Copper-tin System Preparation of the Alloy.—An alloy containing 74.92 per cent (by weight) of copper and the balance tin was chosen for this investigation. This alloy, as can be seen from a portion of the constitutional diagram, Fig. 1, of the system copper-tin by Hamasumi and Nishigori,3 with the proper heat treatment should segregate the « phase out of the a parent, solid solution phase. The alloy was prepared from high purity cathode copper (analyzing 99.98 per cent Cu) and Straits tin (analyzing 99.94

Jan 1, 1933

By N. A. Gokcen, John Chipman

D. C. Hilty (Union Carbide and Carbon Research Laboratories, Niagara Falls, N. Y.)—This paper is a very nicely detailed analysis of a difficult problem. I would like to point out that the results that Mr. Crafts and I published a few years ago had no reference to activity, or anything else of a similar nature; our results were strictly empirical. It is quite gratifying that we now have a case where results involving activity coefficients and results derived from direct observations on actual steel melts are practically identical. When two different laboratories, working from two entirely different approaches, come out with results in such good agreement in their major significance, that is an achievement. It is something that was not possible 15 or 20 years ago. There is one question I would like to ask Dr. Chip-man. It has to do with a very minor point of disagreement in these results. When we reported the kink in the Si-O solubility curve I think you may recall that it came at the different temperature levels at about the order of 0.015 to 0.03 pct 0 and 0.03 to 0.07 pct Si—we also pointed out that we had difficulty in obtaining data at that level, although we finally did get some. I note in going through the data for the present paper, that there are no samples in those particular silicon and oxygen ranges. I wonder if that was purely accidental or was there a reason for it. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—Mr. Hilty, do you have any explanation for that discrepancy between Dr. Chipman&apos;s curve and your own Mr. Hilty—Our explanation for it at that time was that for some reason our system probably was not in true equilibrium with SiO, that is, in equilibrium with the silica crucible at that level. We did observe, however, that that was the level at which both the metal and the slag became saturated with SiO,. On the average, in studying inclusion formation in small ingots permitted to solidify normally from the molten state, we observed pure silica inclusions at silicon contents over about 0.05 pct and FeO type inclusions at silicon

Jan 1, 1953

By H. J. Struth

In these trying times of proration and low oil prices, it is decidedly necessary for all branches of the petroleum industry to accord full recognition to the economic phenomena that contribute to its varying state of welfare. Perhaps no other single factor has a more important bearing upon the general oil situation than the supply and demand of gasoline. Year after year, the records have shown that the degree of prosperity or depression accompanying the industry&apos;s developments has been to a large extent influenced by the degree of balance maintamed between the supply and demand of gasoline. More and more it is being realized within the industry that equilibrium between the supply and demand of gasoline forms the basic structure of crude and product market values and, consequently, the deciding factor in the financial results of the industry as a whole. The influence of the gasoline situation upon the market and financial structure of the petroleum industry was effectively demonstrated during 1930, when excess accumulation of gasoline undermined not only the refined oil market but the crude market as well. In fact, it was a top-heavy gasoline situation that defeated the realization of benefits that might have accrued from an otherwise favorable statistical position in the producing branch of the industry. Indicative of this is the fact that crude oil production was curtailed to the extent of 98,323,000 bbl. last year, while refinery runs to stills were maintained at an excessive rate until late in the year, creating an excess gasoline production of 6,663,000 bbl. above actual requirements. Nevertheless, the movement to curtail refinery operations during the closing months of the year prevented a far worse situation, although it came too late to turn the ebbing momentum of the general oil market. Despite the severe depression of the market values that accompanied 1930 developments, it can be said that the results attained during the closing months of the year, in the direction of production control, marked a decisive turn in the industry&apos;s economic affairs. In fact, a review of the oil situation from every angle points definitely to a better general understanding and recognition of the workings of the economic law of supply and demand. As a result, the year closed with crude production in

Jan 1, 1931

HAVING previously shown you how ores are found and mined, and also how they are prepared and disposed for smelting, and then how the blast furnaces and other furnaces are made for purging their earthiness, all this would be as nothing if I did not proceed to show you the method of smelting them. Therefore, in the present chapter I wish to show you how you must proceed in this very important operation, telling you all I have seen and also how much work with this kind of blast furnace I have done or directed. For this reason I tell you first to take by weight or measure the quantity of ore that you wish to smelt and, particularly if it is a kind that contains silver, break it into small pieces about the size of [52v] beans. If the ore had previously needed evaporation by fire or cleaning by washing, you will have had this done well and have had it properly prepared by a master sorter or others. A layer of this is arranged on a bed of planks, bricks, or flat stones in front of the blast furnace and its companion is placed on top, then a quarter part of galena or a third if you can obtain it. Then an equal part of crushed iron slag or slag from the same or different ore is added. These materials are spread in layers one above the other. When the blast furnace has been constructed as taught above, correct in all its parts, and is full of well-kindled burning charcoal, then fill it up with charcoal and admit water to the bellows machine. When you see that it is well kindled again from this wind and that the flames begin to come out forcefully on top, work it down with a little rake and fill it up again. Then the pannier is filled with new charcoal, the blast furnace heaped full, and another basketful of the said composition of ore is also put on top. Proceed in this way, continually adding charcoal and ore as long as you have any, or as long as you wish to keep up the work, maintaining the blast furnace always full, or continuing in this way until the bottom of the blast furnace is filled with melted materials. Decide this by judgment, or by seeing through the mouth of the tuyère where the wind of the bellows enters that they are level with this. Then with an iron tool open the hole that was left as an outlet in front of the blast furnace and allow all the metal with its slag to run out. These two things, flowing through the chan-

Jan 1, 1942

By C.A. Zapffe

Both the foundryman and the theoretical metallurgist are now generally agreed that the anomalous "rising" or "bleeding" of certain ferrous castings of killed metal is primarily attributable to hydrogen. How and why the phenomenon occurs, however, have not been made clear. The following discussion is intended to harmonize foundry experience with metallurgical theory so that the foundryman may possibly improve his ability to prognosticate whether a certain casting may bleed or not. Bleeding, Rising, and Piping The "rising" to be discussed here is not to be confused with the action in rimming ingots as a result of the carbon-oxygen reaction, although a conclusion will be drawn that may apply to the art of controlling the rimming action. Only killed metal is considered, which includes both steels and irons. In Fig. I, three killed, chill-cast ingots are shown: a porous ingot whose evolution of gas during late stages of solidification has ejected metal through the top; an ingot in which moderate gas evolution during solidification has lifted the mushy central metal, i.e., it has "risen"; and, third, a sound ingot with good piping characteristics. The first type is referred to as "bleeding," and generally infers that a solid skin had first formed through which the liquid metal later erupted. There is no fundamental distinc- tion between bleeding and rising in reference to killed metal.* Porosity Hydrogen appears as a cause of bleeding because the gas evolution simultaneously leaves a porosity of a type traceable to hydrogen. Twenty years ago, Melmoth&apos; noted that killed steel that rose unexpectedly in the mold, if returned while liquid to the furnace and heated further under a reducing lime slag, would again rise in the mold; but that if the ingot were allowed to solidify and was then remelted no rising occurred. A critical quantity of the responsible gas is therefore removed by the rising action. Melmoth associated rising with high silicon (0.7 to 0.9 per cent) and concluded that silicon increased gas absorption. Because silicon is a strong deoxidizer, oxygen must, therefore, be eliminated from consideration of the three common gases in steel—oxygen, nitrogen, and hydrogen. Butterworth2 later decided that pinhole porosity was caused by gases dissolved in the metal and that hydrogen was obtained from steam in the mold. Allen&apos;s classical work on copper castings,3 soon followed by

Jan 1, 1943

By John O. Farmer

The wire-line tubing perforator is a mechanically operated tool that is run on an ordinary steel measuring line into the tubing of a well, under pressure, to drive into the wall of the tubing, and securely lock in place, a tapered, cylindrical insert containing an orifice. Use of the perforator obviates the necessity of pulling and rerunning the tubing to install jet collars or flow valves, reduces the cost, and simplifies the task, of placing an oil well on gas-lift operation. More important, however, is the use of the tool with a removable check valve and stop, to provide a means of washing drilling mud from the annulus between the tubing and casing, and to complete the well for gas lift operation without exposing the producing formation to the mud column and without moving the tubing string. This paper discusses the origin, development, and mechanics of the wire-line perforator, the various purposes for which the tool was designed, and the method of selecting orifice sizes for any depth, and gives the results obtained thus far in practical application. Origin and Development Several years ago, a tool that could be lowered on an ordinary steel measuring line into the tubing of a well under pressure was designed and constructed for the purpose of punching a hole in the tubing walls above a shale bridge that had completely plugged the tubing of a well in the Long Lake field, East Texas. The well was in a low, swampy area, which excessive rainfall had caused to be in- accessible by car or truck for about four months. The only equipment at the well site consisted of an ordinary steel wire line that had been carried there to measure the depth of the bridge. Since a pulling unit could not be moved to the well site, and as the pressure on the casing was 2100 lb. per sq. in., it became apparent that the only way out of the predicament was to make a perforating tool that could be lowered into the tubing on a measuring line and operated under Pressure. Thus, the first wire-line tubing perforator was designed and built as an expedient, and was not used extensively until it had been redesigned to meet more frequent and increasingly urgent needs. Until recently, it was necessary to pull the tubing to install jet collars or flow the when a well was to be placed On gas lift. Because most companies either maintained or had access to pulling units and crews for this work, little or no thought had been given to eliminating or even simplifying this task. When the manpower and steel shortage became so acute, however, many operators suddenly found themselves without facilities to equip their wells for gas lifting. The wireline tubing perforator already had been tried and proved successful, therefore operators immediately requested its use to punch gas-jet holes in the tubing, to eliminate the pulling and running of tubing strings. The first deficiency revealed by more general use of the perforator lay in the inability to regulate the size of the hole punched through the tubing. The size could not be controlled to any degree of

Jan 1, 1946

By John O. Farmer

The wire-line tubing perforator is a mechanically operated tool that is run on an ordinary steel measuring line into the tubing of a well, under pressure, to drive into the wall of the tubing, and securely lock in place, a tapered, cylindrical insert containing an orifice. Use of the perforator obviates the necessity of pulling and rerunning the tubing to install jet collars or flow valves, reduces the cost, and simplifies the task, of placing an oil well on gas-lift operation. More important, however, is the use of the tool with a removable check valve and stop, to provide a means of washing drilling mud from the annulus between the tubing and casing, and to complete the well for gas lift operation without exposing the producing formation to the mud column and without moving the tubing string. This paper discusses the origin, development, and mechanics of the wire-line perforator, the various purposes for which the tool was designed, and the method of selecting orifice sizes for any depth, and gives the results obtained thus far in practical application. Origin and Development Several years ago, a tool that could be lowered on an ordinary steel measuring line into the tubing of a well under pressure was designed and constructed for the purpose of punching a hole in the tubing walls above a shale bridge that had completely plugged the tubing of a well in the Long Lake field, East Texas. The well was in a low, swampy area, which excessive rainfall had caused to be in- accessible by car or truck for about four months. The only equipment at the well site consisted of an ordinary steel wire line that had been carried there to measure the depth of the bridge. Since a pulling unit could not be moved to the well site, and as the pressure on the casing was 2100 lb. per sq. in., it became apparent that the only way out of the predicament was to make a perforating tool that could be lowered into the tubing on a measuring line and operated under Pressure. Thus, the first wire-line tubing perforator was designed and built as an expedient, and was not used extensively until it had been redesigned to meet more frequent and increasingly urgent needs. Until recently, it was necessary to pull the tubing to install jet collars or flow the when a well was to be placed On gas lift. Because most companies either maintained or had access to pulling units and crews for this work, little or no thought had been given to eliminating or even simplifying this task. When the manpower and steel shortage became so acute, however, many operators suddenly found themselves without facilities to equip their wells for gas lifting. The wireline tubing perforator already had been tried and proved successful, therefore operators immediately requested its use to punch gas-jet holes in the tubing, to eliminate the pulling and running of tubing strings. The first deficiency revealed by more general use of the perforator lay in the inability to regulate the size of the hole punched through the tubing. The size could not be controlled to any degree of

Jan 1, 1946

By C. A. Zapffe

Both the foundryman and the theoretical metallurgist are now generally agreed that the anomalous "rising" or "bleeding" of certain ferrous castings of killed metal is primarily attributable to hydrogen. How and why the phenomenon occurs, however, have not been made clear. The following discussion is intended to harmonize foundry experience with metallurgical theory so that the foundryman may possibly improve his ability to prognosticate whether a certain casting may bleed or not. Bleeding, Rising, and Piping The "rising" to be discussed here is not to be confused with the action in rimming ingots as a result of the carbon-oxygen reaction, although a conclusion will be drawn that may apply to the art of controlling the rimming action. Only killed metal is considered, which includes both steels and irons. In Fig. I, three killed, chill-cast ingots are shown: a porous ingot whose evolution of gas during late stages of solidification has ejected metal through the top; an ingot in which moderate gas evolution during solidification has lifted the mushy central metal, i.e., it has "risen"; and, third, a sound ingot with good piping characteristics. The first type is referred to as "bleeding," and generally infers that a solid skin had first formed through which the liquid metal later erupted. There is no fundamental distinc- tion between bleeding and rising in reference to killed metal.* Porosity Hydrogen appears as a cause of bleeding because the gas evolution simultaneously leaves a porosity of a type traceable to hydrogen. Twenty years ago, Melmoth&apos; noted that killed steel that rose unexpectedly in the mold, if returned while liquid to the furnace and heated further under a reducing lime slag, would again rise in the mold; but that if the ingot were allowed to solidify and was then remelted no rising occurred. A critical quantity of the responsible gas is therefore removed by the rising action. Melmoth associated rising with high silicon (0.7 to 0.9 per cent) and concluded that silicon increased gas absorption. Because silicon is a strong deoxidizer, oxygen must, therefore, be eliminated from consideration of the three common gases in steel—oxygen, nitrogen, and hydrogen. Butterworth2 later decided that pinhole porosity was caused by gases dissolved in the metal and that hydrogen was obtained from steam in the mold. Allen&apos;s classical work on copper castings,3 soon followed by

Jan 1, 1943