Search Documents

By J. J. Frawley, W. J. Childs

The dynamic nucleation of supercooled bismuth and Bi-Sn alloys has been studied over a frequency range of 15 to 20,000 cps. For low-frequency vibration, a minimum vibrational energy was required for enhancement of nucleation. Above this critical energy, the dynamic supercooling was less than static supercooling showing that vibration promoted nucleation. The amount of dynamic supercooling continued to decrease with increasing vibrational energy until a minimum or threshold value was reached. This minimum value of supercooling for nucleation remained constant joy all further increases in vibrational energy. For higher frequencies, similar results were observed. This behavior has been related to the necessity of cavitation for dynamic nucleation. When a liquid is cooled to a temperature below its equilibrium melting point, the solid phase is more thermodynamically stable. However, for solidification to occur, a two-step process, nucleation and subsequent growth of the solid phase, must occur. When a liquid is supercooled, that is cooled below the equilibrium melting point, the controlling process for solidification to begin is the rate of nucleation. Once nucleation has occurred, the solidification process is controlled by the rate of growth. Nucleation can be induced by two factors: either by a catalyst or by the use of mechanical shock. Numerous investigators1-4 have studied the effect of nucleation catalysis but much less systematic study has been made of nucleation by mechanical shock waves. The influence of vibrations on grain size in castings and ingots has been studied by many authors but no clear understanding of the mechanism or accurate prediction of the effect has been presented.5 It would be intuitively expected that the further the departure from equilibrium (i.e., the greater the supercooling), the easier it would be to induce nucleation. This has been quantitatively demonstrated both by walker6 and later by Stuhr,7 that the greater the degree of supercooling the easier it is to nucleate by a shock wave. Stuhr also attempted to obtain the mechanical energy required for nucleation of bismuth as a function of supercooling. He vibrated a crucible containing supercooled metal at low frequencies and various amplitudes and noted the corresponding dynamic supercooling obtained. The amount of supercooling was inversely proportional to the mechanical energy applied. Limitation of his experiment was the problem of the confinement of the liquid in the crucible without splashing and minimizing other unwanted modes of vibration. Tiller et al.8,9 did similar work on tin and Sn-Pb alloys using an electromagnetic stirring device. Their conclusions were that the magnitude of the magnetic field strength did not affect the amount of undercooling at which nucleation was initiated. While conclusive experimental results have been lacking to explain this effect of mechanical vibration on inducing nucleation, a number of theories have been proposed. Two of these theories are discussed below. 1) The Change in Melting:- Point Locally Due to the Change in Pressure (Clapeyron Equation). According to Vonnegut10 the most plausible explanation for the nucleation of a supercooled melt by cavitation is the effect of changing the melting point by a change in pressure. For materials where the volume decreases on solidification, an increase in pressure raises the melting point; for materials which expand on solidification, the melting point is raised for a decrease in pressure, i.e., rarefaction. Using the Clapeyron equation, the melting point of a metal can be calculated as a function of pressure. If it is assumed that the equation can also be used to calculate the temperature of nucleation of a supercooled melt as a function of pressure (i.e., the temperature of heterogeneous nucleation will increase with pressure at the same rate as the melting point), the amount of supercooling required for nucleation will be constant at all pressures as shown in Fig. 1. It is obvious that an isothermal change which results in an increase in melting point results in an equal increase in supercooling. This increase in supercooling may now be sufficient for nucleation. A pressure of 80,000 atm was calculated, using the Clapeyron equation, as the pressure required to increase the temperature of nucleation of nickel by 200°C. According to Lord Rayleigh,11 this very large pressure could be generated for a very brief period of time by the collapse of a cavity. This pressure wave is radiated in all directions from the collapsed cavity. If the temperature of the melt is slightly below its equilibrium melting temperature at atmospheric pressure, stable growth can follow; that is, once nucleation occurs, growth becomes the main driving force of the solidification process. This proposal has been extended to water which expands on freezing by assuming that nucleation occurs during rarefaction following the pressure pulse. This negative pressure pulse should follow immediately after the positive pressure pulse with its magnitude approaching the critical tensile strength of the liquid. The negative pressure developed during this period would raise the melting point of water and thus promote nucleation. Hunt and jackson12 have suggested this for water. Similarly, it could be postulated that bismuth which also expands on freezing could be nucleated during the negative pressure pulse. 2) Nucleation by a High-pressure Phase. An extension of the Clapeyron equation to systems where density decreased on freezing at atmosphere pressure has been proposed by Hickling.13 The phase diagram for water initially shows the well-known decrease in

Jan 1, 1969

By A. D. Hodges

In May, 1850, the first gold from the Comstock lode was discovered in the sands near the Carson river. It had been washed down by natural agencies, through Gold Caflon, from the decomposed rock of the ledge above. Within a few weeks, the precious metal was traced more than three miles in shallow deposits along the bed of the canon, from the river to the Devil's Gate-—a narrow, rocky cleft, notable to the teamsters of a later day chiefly as the place where " Uncle Jimmy Fair" collected high tolls, and could not reduce the rates, because " this was all he had for the education of his poor children." From 1850 to 1857, a fluctuating band of miners, whose number varied from twenty to two hundred, washed the Gold Canon placers with rockers and long-toms, making four to five dollars a day each until the last-named year, when the deposits were in great measure exhausted. The chief settlement of these miners was at Johntown. During only a third of the year was the water-supply sufficient for their work. The remainder of the time they utilized in desultory prospecting of the hills and in occasional forays for supplies among the Mormons in Carson valley. In 1857, the Grosch brothers discovered the Comstock lode at some point, now unknown, in Gold Hill, but their discovery perished with them. Early in 1858, the " Pioneer Quartz Company," having located several of the small surface-veins around Silver City (whose connection with the main lode has never been definitely shown), built an arrastra, and worked some of their ore; but the returns were so small that they soon abandoned this business. The following winter, James Finney and his partners found gold in place in

Jan 1, 1891

By Rossiter Raymond

(Butte Meeting, August, 1913.) ON Mar. 28, 1913, the Board of Directors of the American Institute of Mining Engineers unanimously adopted the following Minute: JOHN FRITZ, one of the most distinguished of American mechanical and metallurgical engineers, won that position by the force of innate genius, indomitable industry, unstained integrity and unfailing sympathy, and generosity towards his fellow-men. Self-educated in the hard school of practice, he appreciated nevertheless the advantages of technical instruction and discussion, and evinced this appreciation both by his membership and lively interest in this and other similar societies, and by his munificent gifts to engineering education at Lehigh University, and his long and faithful service us a Trustee of that institution. . As one of the foremost of those American engineers who, through their brilliant inventions and practical skill. developed here -the modern iron blast-furnace -and rolling-mill, and introduced and perfected the Bessemer process and other improvements in the manufacture of steel, Mr. Fritz contributed mightily to the chief departments of that industrial progress which characterized the Nineteenth Century. Proud of his great achievements, we cannot but rejoice over his long and fruitful life, crowned with a peaceful death ; but our praise and thanks are mingled with sorrow, as we recall the kindly face which we shall see no more on earth, and the loyal friendship and spontaneous good-will which led the love of his generation, and the reverence of the generation which followed, to regard him universally as " Uncle John Fritz." That. summary, though only an outline, is a good portrait ; and in the present sketch, we shall do no more than supply some details of the likeness, and some elements of the background.

Jan 6, 1913

By E. A. Swedenborg, J. S. Ross

Oil-field waters enter into many underground problems with which the petroleum engineer has to deal. Whether the problem is one of infiltration or natural encroachment, it is always desirable to determine the source of the water before commencing repair or remedial work. The usual mechanical tests for determining the source of extraneous water in wells are slow and expensive. An excellent means for the identification of oil-field waters may be afforded by their chemical characteristics when the chemical character of waters from the various sands has been established by careful sampling and analysis cautiously interpreted. In the Salt Creck field, Wyoming, a fairly high degree of efficiency has been attained in the control of field operations by utilizing the information afforded by the analysis. All of the operating companies appreciate this means of identifying waters, with the result that water-sampling has become general practice. Most of the chemical work dealing with Salt Creek waters has been done since the laboratories of the Midwest Refining Co. and the U. S. Geological Survey, were established in the field; the former in 1922, the latter in 1924. A spirit of cooperation has existed between the company and the government personnel by which many of the data for this paper were made available. Sands of the Salt Creek Field The principal sand horizons in the Salt Creek field are the Shannon, First, Second, and Third Wall Creeks, Dakota, Lakota, Sundance and Tensleep. Of these the important oil producers are the First Wall Creek, Second Wall Creek, Lakota and the Sundance. The Third Wall Creek is lenticular and is productive in only a few wells in the southern end of the field. There are also a number of shale wells, but they do not produce water in any appreciable amount. The stratigraphic position of these sands and their relative thicknesses are shown on the condensed composite section of Salt Creek

Jan 1, 1929

By J. Mazia, H. Rosenthal

An investigation has been made of residual stress in the head and body of caliber 0.30 cartridge cases. The head was divided into four ring-lie sections which were cut off by a jeweler's saw. Spring-out was measured after a radial cut had relieved the circumferential bending moment. The residual stress corresponding to the observed spring-out was calculated by formulas in which the computed stress was a function of wall thickness. All rings sprang open, indicating compressive stress on the inner wall and tensile stress on the outer wall. The production stress-relief anneal of 475 F. for 45 min. reduced the stress to almost half. The priming and crimping operation, however, again raised the stress, especially in the flange section. The dect of stress-relief heat treatments on residual stresses in the body of caliber 0.30 cartridge cases was investigated by the split-ring method. Although this method did not reveal any large stresses in the body, the neck before mouth anneal was found to contain a computed stress of 30,000 psi. at the surface. This value was reduced to 15,000 psi. in 120, 30, and 15 min. at 400, 475, and 500 F., respectively.

Jan 1, 1945

By Peter N. Calder, Alan Bauer

INTRODUCTION One of the most important decisions involved in the design of an open pit mine is the selection of a slope angle. Despite this fact, engineering procedures have developed slowly in this field. Only recently have the instruments and know-how become available to undertake a design based on sound engineering principles. The effect of blasting on open pit slope stability is one aspect in which the state of the art has not developed fully. These effects include: a) the effects of the ground motion associated with blast waves on slope stability, and b) the fracturing of rock in the vicinity of slopes caused by blast waves. Natural rock jointing plays an important role in both of these. SUMMARY OF BLASTING EFFECTS In recent years there has been a trend to larger sizes of blast holes in open pits to the extent that today 9% in. and 12% in. diam. holes are the most common. The reasons for this have been economic. Larger machines are more efficient and produce at a lower overall cost per ton. As the size of blast holes have increased, so have the other factors associated with blasting. Bench heights have increased, the tons/ft. of hole yield has risen significantly and the explosive load per hole has increased. Quite naturally the rupture radius for a single blast hole has increased along with the vibration level produced per blast hole. Open pit blasting operations can result in two types of unwanted damage: 1. Damage to structures, such as buildings, dams and slopes by ground vibrations initiated by the blast. 2. Fracturing of ground beyond the planned excavation limits. Let us first consider item one. Vibration effects are determined by the type of blast which is fired and the type of medium through which the blast wave is being transmitted. They are strongly influenced by the weight of charge per hole, the number of holes per delay, the distance from the shot point, the mode of initiation, the point of interest relative to the blast, etc.

Jan 1, 1971

By H. Biloni, H. R. Bertorello

GruZLESKI and winegard1 have recently reported on the origin and development of the cellular substructure in Sn-Cd eutectic unidirectionally grown with different amounts of constitutional supercooling (CS). This communication deals with the results obtained in a parallel study on the instability of a plane interface in Al-Cu eutectic unidirectionally grown. Similarities as well as differences with the results of these authors1 will be presented. A1-Cu eutectic alloy ingots of 99.999 pct purity were grown unidirectionally under different G/R ratios where G = thermal gradient in the liquid, R = solidification rate. The ingots were cut in slices perpendicular to the solidification axes and the substructure studied on parallel sections following the sense of growth. It was generally found that the last part of the ingot to solidify presented a well developed colony substructure as a result of impurity build up and constitutional supercooling. The results obtained were: 1) When the structure was observed with low niagnification (of the order of 150 to 300 times) the first instabilities were observed at the grain boundaries and node-like structures formed at the junctions of the growth-induced boundaries, as reported by Gruz-leski and Winegard.1 Inside the grains the first signs of instability appear later and correspond to the type shown in Fig. 1; this is a two dimensional cell substructure. ' 2) Figs. 2 and 3 correspond to the evolution from a two dimensional substructure to a cellular type. In the A1-Cu eutectic the boundaries of the two dimensional cell are always perpendicular to the laniellaes instead of parallel as in the Sn-Cd eutectic. 1

Jan 1, 1970

By John L. Ham, Robert M. Parke

THE melting point of molybdenum is 2625° ± 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. 1, 1944, to Aug. 31, 1945, the project was under the supervision of the National Defense Research Committee, Division One. In peacetime, too, there are needs for molybdenum, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. FIRST PROCESS FOR MELTING AND CASTING MOLYBDENUM The maintenance of a temperature greater than 2625°C. in a space large enough to melt several pounds of molybdenum may involve the loss of heat at a very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum. In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1946

By Max Mason

IN 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ, one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect, which penetrates into the ground and is distorted and, reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in, reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert's study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to, reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are-spared the necessity of using a messenger, because nature has already provided one. For example, we already have a terrestrial magnetic field which auto-matically and continually conveys messages from underneath. We also have available the earth's gravitational field which furnishes us

Jan 1, 1927

By H. W. Hitzrot

SEPARATING a mixture of particle sizes of material suspended in a liquid medium is by no means an exact science. Selecting machines for individual classifying operations is even more difficult. The plant operator's own background is of course invaluable, and considerable help may be obtained from technical articles, talks with sales engineers, and handbooks on ore dressing. These several sources of information, however, are difficult to marshal in proper perspective for the major decision on classification units that an operator may be called upon to make. To the present writer's knowledge this assembly of facts is not available in handbooks, and technical papers are scarce on classification equipment developed in the past five or six years. It is believed that this paper will be helpful to users of classification equipment at this particular period in the development of hydro-classification. For easy reference the following classification units now available and in use in metallurgical and industrial operations are listed below, with a brief description of each. Unit-type classifiers, bowl classifiers, and bowl desiltors are all rectangular tanks, slightly tilted, with reciprocating rakes or screws to remove settled sands. The unit-type classifier, Figs. 1 and 2, is available in widths from 14 in. to 20 ft and lengths up to 40 ft. The shallow bowl of the bowl classifier, Fig. 3, equipped with rotating rakes, is superimposed on the lower end of the tank. Reciprocating rake compartments for this design range from 18 in. to 20 ft wide. Bowl diameters vary from 4 to 28 ft. The flat-bottomed bowl of the desiltor, Fig. 4, of relatively large diameter, is equipped with rakes rotating outward and partly over a pit, which is created by extension of the rectangular tank into and under the bowl section. Bowl desiltors are available with reciprocating rake sections 4 to 20 ft wide and bowls from 20 to 50 ft in diam. The bowl desiltor is used for applications beyond the range of the bowl classifier. The hydroseparator, Figs. 5 and 6, is a circular tank equipped with slowly rotating rake arms, set on a slope, with interrupted rake or spiral blades to move the settled solids to a central discharge cone. Tank diameters vary from 4 to 250 ft. Tank depths at center are 2 to 3 ft for small units and up to 25 ft for larger units. Hydraulic classifiers of the sizer and super-sorter types, Figs. 7 and 8, are narrow, deep, rectangular tanks divided by vertical baffles into a series of pockets. Hydraulic water is added near the bottom of each pocket. Perforated constriction plates, spiral flow arrangements, or jets are used to disseminate the water under pressure (hydraulic water) throughout the bed of material in the pocket. Discharge valves on each pocket are operated automatically by a pneumatic mechanism, a pincer-type mechanism, or a pressure control and motor combination actuated by a hydrostatic tube within the pocket. Hydraulic classifiers are available in 4, 5, 6, and 8-pocket units of varying constriction plate areas to suit conditions. There is now a jet sizer of unit pocket design that can be made up in 1 to 25 sections or more to accommodate sizing requirements. The hydroscillator, Fig. 9, is a rectangular tank set on a slope of 3 to 4 in. per ft. A bowl is superimposed on the lower end. The bowl bottom is an oscillating rubber-covered disk, perforated to allow hydraulic water introduced beneath the disk to set up a teeter bed and thus produce an oversize or rake product exceptionally free of slimes, and material minus the mesh of separation. A shallow dam at the periphery of the bowl allows the coarse or oversize fraction to spill over and drop down into the tank compartment, where it is moved up the deck by reciprocating rakes. The material, minus the mesh of separation, overflows a circular and stationary weir which is several inches higher than the dam on the oscillating disk. It is carried off in a circular launder in the usual manner. These units are available in bowl diameters from 4 to 14 ft and with reciprocating rake compartment widths to suit the tons per hour to be handled. Centrifugal classifiers include the solid bowl centrifuge and the cyclone classifier. The solid bowl centrifuge, Fig. 10, consists of a truncated cone fixed to a horizontal shaft and rotating at high speed. An internal spiral rotating at slightly less speed continuously removes solids deposited on the inner surface of the cone, or bowl. Feed enters the cone by means of the hollow center shaft. Overflow leaves through ports at the large end of the cone, and oversize solids, moved by the spiral, exit through ports at the small end. Centrifugal classifiers of this type are available in cone diameters from 18 to 54 in. The cyclone classifier, Fig. 11, is a stationary cone having a cylindrical upper section and a lower cone section. Feed is introduced tangentially into the upper cylindrical section under pressure from a hydrostatic head or by means of a pump. Centrifugal force thus induced effects a classification within the cone, the fine sizes being carried off in the overflow through an opening at the top of the cylindrical section. Coarse solids at relatively high pulp density exit through a control valve at the apex of the lower cone section. Cyclone classifiers are available in 3, 6, 12, 14, 24, and 30-in. diam. The cone classifier, Fig. 12, is a steel-plate cone with sides usually about 60" from horizontal. It contains no rotating mechanism. Feed enters a feed-well at center and classification is effected by gravity and pulp density. Fines are carried off in the flow over a peripheral weir at the top of the cone. Settled solids exit through an opening at the apex. An apex valve actuated through levers and rods by the pulp density in the lower cone section is usually supplied. Diameters are usually maximum at 8 ft.

Jan 1, 1955

By C. G. Brehm

THE anthracite-producing region is in the northeastern section of Pennsylvania, and has an area of approximately 484 square miles. It is divided geographically into three separate fields, known as the Northern, Middle and Southern. The Northern field, with Wilkes-Barre approximately at its center, is a basin about 60 miles long and almost 6 miles wide at its greatest distance across. Generally speaking, it may be said that the coal meas-ures in this field lie horizontally, or on slight pitches, and consist of from 11 to 19 veins of coal, varying in thickness from several inches to several feet. The intervening strata between veins may be composed of slate, clay, rock or shale, or a combination of several, and are sometimes very thin. This condition often causes a treacherous roof, therefore roof sup-port and the attending hazard of mining are problems of concern. The Middle field is made up of a number of small basins of not very great depth, and the measures, which are in like number to those of the Northern field, are varying inclinations running from nearly flat to steep pitches.

Jan 1, 1938

By Klaus Schoenert

In the analysis of comminution processes, it is necessary to have a detailed knowledge of such subprocesses as: transportation of the particles to the zone where they are stressed; the stressing of particles to a level high enough for breakage; removal of the fragments that are smaller than the limit size from the grinding zone; and prevention of agglomeration of the fine fragments. Breakage phenomena of particles is the most difficult subprocess to understand. It can be understood only by applying the principles of fracture physics to obtain information about the stress-strain field in particles which are loaded either by compression or by impact, and by using this theoretical knowledge to interpret experimental results obtained from single particle crushing studies. Two important features of the "Science of Communition" are discussed: the fracture physics and crushing under controlled conditions with special reference to single particle crushing, packed bed crushing, measurement of energy needed for fracture, fragment size distribution, and new surface area produced. The important features of these aspects are detailed, namely, energy balance of a crack, influence of environment, specimen size problems, and energy utilization in single particle crushing.

Jan 1, 1973

The Library of the above-named Societies is open from 9 A.M to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should he made as definite as possible so that the information received may he what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 6, 1918

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society, but the name has now been changed. to one which more nearly reflects the real function of the corporation. It holds title to the Engineering Societies Building and to various funds placed in its charge and is managed by a Board of Trustees, of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical Engineers, American Society of Mechanical Engineers, American Institute of Electrical Engineers and American Society of Civil Engineers, which have equal and undivided interests in the property. The land and building cost two million dollars. During the gear 1934, the constitution and By-laws of The United Engineering Trustees, Inc., were thoroughly revised and a better organization of its functions was affected: The Engineering Foundation and the Engineering Societies Library were made "departments? of the United

Jan 1, 1936

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of quartz with oleic acid as collector and barium, calcium, aluminum, iron, and tin as activators were studied using a simple vacuum-flotation technique in glass-stoppered graduates. The detailed study of barium activation led to an interpretation based on ideal Langmuirian chemisorption.

Jan 5, 1950

With the signing of the armistice on Nov. 11, the direction of the main concentration of effort of the United States was changed. In order to win the war, all industrial efforts had to be organized and centralized. With the war won and peace in sight, this centralization of effort stopped and the full play of individual initiative was allowed to resume its sway in the community. During this period of reversal of direction of effort, there was a natural loss of momentum and the United States, as well as the rest of the world, is in for a period of readjustment. The immense progress that was made in one direction under the stress of the necessities of war, which focused the energies of a nation in one direction, is an outstanding example of what can be accomplished if a community with many varying interests can be united on one objective which it desires to attain. The realization that the fusing of many interests into one stream of effort is difficult should not prevent us from taking the long view ahead that is necessary in order to be able to measure the progress made. If we don't have a mountain peak to guide us, we are very likely to run in circles in the plain without reaching the goal to which we strive. The most efficient development of natural resources is an ideal that, from a material point of view, appeals to the engineer. This ideal includes giving of opportunities to everyone to take a share in the development of these resources.. It also contemplates rewarding foresight

Jan 4, 1919

By William C. Grady

Microscopic pyrites are present in all West Virginia coals. Sizes of these pyrites range from 0.1 µ 500 µ (1/2 mm) , and four types are noted: massive, patches, framboids, and isolated crystals. The relative and absolute abundances of the four types vary from seam to seam, and these distributions have a marked effect on the ease with which a seam may be cleaned of pyritic sulfur.

Jan 1, 1978

By J. R. Thompson

It is common practice, and certainly good business as all of us know, to take care of plant operating equipment. Machinery of any type requires periodic inspection and planned maintenance. With this thought in mind a plant operator should at the end of every shutdown period make regular belt inspections and plan for later appropriate care and maintenance. The points mentioned below are understood well by all of us but are sometimes forgotten because belt conveyors are comparatively easy to operate. Maintenance of any conveyor belt is dependent upon the fundamental characteristics of the two component parts-cover and carcass.

Jan 6, 1950

By Granville S. Borden, Frank H. Madison

The fruits of industry are divided between capital, labor, and governments. Capital takes its redemption and remuneration through profits or dividends; labor takes its share through wages; governments take their share through taxes. Each must have a just share, and the question of what is a just share and the question of who shall make the allocation are vital current political and economic issues. Certain political philosophies con- tend that government should take all the fruits and that some dictator or politician should have irrevocable discretion and power to distribute the fruits. Believers in democracy and free enterprise adhere to the view that capital is entitled to redemption and fair remuneration; that labor shall have a fair wage; and that governments shall make equitable levies. But since all human beings, both individually and in groups, are inherently selfish, there are many variable views in regard to the question of what ratios shall be applied in a division of the fruits and who shall have the power to fix these ratios. Perhaps all parties should devote more energy to means of increasing the crop, and not so much time to quarreling over a division of the existing crop. Moreover, all three parties must guard against killing the goose that lays the mineral eggs. For example, if the tax burden becomes oppressive and the taxpayer refuses to carry it, then business stagnates, with consequent unemployment, reduction of profits, and curtailment of government revenue. If a producer assumes the increased tax burden, marginal operations must be closed down, and, again the consequences are increased unemployment and diminished government revenue. Quite often an increase in a rate of tax results in a reduction of government revenue. Perhaps the worst detrimental feature of selfishness and greed on the part of any one of the three distributees of the fruits of industry is the retardation of expansion of the enterprise. Growth means new jobs, more government revenue, better trade, and better standards of living. Explorations and discoveries have resulted in tremendous contributions

Jan 1, 1964

By Harry V. Welch

This paper presents a brief discussion of numerous devices and processes which have been utilized for the recovery of values from gases in copper reduction works and describes in greater detail the development and application in recent years of electrical precipitation, more familiarly known as the Cottrell process, to the problems of dust losses with furnace gases in copper-smelting and refining plants. The field for collection of suspended particles in gases is widely extended in our modern complex, congested .and industrialized mode of living, and its satisfactory solution is required by our increasing appreciation of the extravagant waste, unhealthful effects and nuisance which such uncontrolled emission of solid suspensions represents. Much of the special dust-recovery equipment in use today has been developed in one industry and carried over to many others. The early work of Cottrell was with sulfuric acid mists, aimed at the purification problem in contact acid manufacture, but the present uses of Cottrell equipment cover a diversified field—carbon black, combustible gas, oil mists, iron blastfurnace fumes and dusts, cement-kiln gases, as well as the purification of gases in contact and chamber acid plants and its wide and extended use in the nonferrous metallurgical field of copper, zinc and lead, and their associated metals. Dust and fume collection from furnace gases became a problem only with the modern development of large and amply powered auxiliary furnace equipment, which in turn permitted large furnace units, fast driving and large outputs of finished product per unit of furnace capacity. The ancient metallurgist with his small clay pot and hand-operated bellows had too little gas velocity to cause a real dust loss. As furnaces grew in size, flues and stacks were added, and undoubtedly the first observable dust losses were indicated by the deposits in the flue and stack base. Large flues, it was noted, collected more than smaller ones, and the expansion of a portion of the flue into a chamber represented the first serious attempt at recovery of furnace dust losses. For a century or more the settling chamber represented the best of skilled metallurgical practice in recovery of furnace dust, and it may be said to have reached

Jan 1, 1934