Search Documents

By Enver Alan, MerkeziYapı

People are migrating because of economic, social, natural and political reasons. These natural and humane factors effects the distribution of populations. The need for tunnels has grown in order to provide a comfortable life and reduce losses such as waste of time, labor, energy, efficiency and so on. It is inevitable to carry out excavations in rock tunnels (shears, platforms, lines, connections, wastewater, distribution, energy, transportation etc.), that will be built by excavating with conventional method, by controlled blasting regarding with constrains. In this study of applied explosives engineering the blasting applications are evaluated, which were carried out for research and development purposes at Yenisahra Station tunnels in Kartal Formation which was built with the aim of solving İstanbul's transportation problem within the framework of the Kadıköy-Kartal Metro Project. Twenty-four shots were made by using explosives in 60 blastholes that were drilled in the tunnel faces, which were located between and outside of two different faults. Six microphones were used to measure the air shock and eight geophones were used to measure the parameter values of the vibrations (particle velocity, frequency, displacement, acceleration, amplitude, wavelength etc.), which were placed at predetermined points of the surface, occurred during the blasting applications. Data from the geophone and microphones were recorded on six seismographs. The coordinates and the distances between the shot points and the measurement stations are determined by an electronic theodolite. The total number of seismic records, recorded in seismographs, is 118. The number of records of vibrations that crossed the faults is 42 and the number of records of vibrations that did not cross the fault is 76. The particle velocity, frequency, amplitude, acceleration, displacement and wavelength were measured in transverse, longitudinal and vertical directions. The total number of measurements is 354. By evaluating all seismic records, the effect of delay intervals, faults and scaled distances on the particle velocity, frequency, amplitude, displacement, acceleration, wavelength and air shock were investigated. When the vibrations formed during the Research & Development (R&D) blasts were examined, it was determined that the parameter values of vibrations that crossed the faults are lower than the ones that did not cross the faults. In addition, when the particle velocity values of all vibrations are examined according to the present circumstances, it is determined that the waves did not cross the fault in all delay intervals are superposed in all directions, and that the least superposing occurred in the 50 ms delay range.

TowerMill - Advantages in Wet Grinding Applications The TowerMill, which has now been in existence for no less than 50 years, is one alternative to the horizontal ball mill and offers several advantages. The TowerMill is widely used in (coal-fired) electric power plants for the grinding of raw material for the FGD (Flue Gas Desulphurisation) process involving very high throughputs, very fine product sizes and high availability. Some companies in the mining industry also looked at the use of such optimised grinding machines several years ago and found that many of the advantages offered in other industries are transferable to new applications. Much development work has been undertaken to improve the TowerMill for new applications and, as part of that work, tests have also been conducted to make direct comparisons of their performance with that of ball mills. Grinding tests were performed using the same raw materials and comparable machine sizes. Some of the results are discussed in this paper, along with a comparison of the advantages and disadvantages. The conclusion provides an outlook for some worthwhile future applications. The test results, which are described and analysed, show that the TowerMill offers significant advantages in relation to operating costs and operational safety. An example based on the wet grinding of limestone is presented.

Sep 13, 2010

By Congcong Chen, Bo Ma

When assessing the safety of a tailings dam, the constant weight method (CWM) is one of the most commonly used methods. However, when the evaluation indicator value suggests serious defects, the evaluation value is often inconsistent with the actual situation. To address this issue, the variable weight method (VWM) is introduced to assess the safety of the tailings dam. Initially, a three-layer indicator system for dam failure safety assessment is built, and individual indicator values are divided into four grades. Then, an appropriate state variable weight function is constructed and relevant parameters are determined. Finally, a case study is illustrated to verify the effectiveness of the model. The assessment results of the VWM more closely represent the actual situation than that of the CWM, which is more helpful for decision makers and technicians to take scientific and reasonable precautionary measures, thereby improving the safety management of the tailings pond.

Oct 8, 2022

Advances in Thickener Feedwell Design via Computational Fluid Dynamics Modelling

Sep 13, 2010

By Hori M, Komatsu T

In Japan, a small-diameter tunnel boring machine (TBM) of diameter 2.6 m applicable to a wide range of geology from hard rock to soft strata was developed with the purpose of reducing construction costs of headrace tunnels for small hydroelectric power stations. And in 1983, a demonstration test was carried out in the No. 1 headrace tunnel work of Hayakido Hydroelectric Power Station. The principal achievements in executing work are the following: (1) Although this TBM was a demonstration test unit, excavation advances averaged more than 200 m/month and exceeded the average 150 m/month with a conventional method. (2) According to PS velocity surveys after tunnel excavation the zone of loosening due to the TBM method was small enough to be ignored and was approximately one-half compared with conventional methods in rock of the same evaluation.

Jan 1, 1987

By Arnold O. Tanner

Tables based on 1985 data, which were not available in time for publication of the "1985 Minerals Yearbook," are included in this chapter; corresponding tables for 1986 are not yet available. Raw nonfuel minerals produced in the United States during 1986 had an estimated value of $23.5 billion, an increase of $0.25 billion over the 1985 value. This is the fourth consecutive year that the value has increased, and except for a de- crease in 1982, the value each year has increased since 1971, or 14 out of 15 years. Industrial minerals growth slowed from a 3% increase in value in 1985 to a 1.5% increase in 1986, reflecting the slow growth in the domestic economy. The value of industrial minerals, more than three times larger than the value of metals, easily offset the less than 0.5% decline in the value of metal mine production. Although the decline was small, this decrease makes 1986 the fourth year in the past 6 years in which a drop in the value of metal mining production occurred in the United States. U.S. production continued to lag behind the growing world production. Overall, the estimated raw nonfuel mineral production rose 1% over that of 1985. Domestic mine production of ferrous metals declined as follows, in decreasing order of production: nickel, iron ore, tungsten, and molybdenum. All remaining domestic primary nickel and tungsten mines had closed down by yearend. Nonferrous metals that similarly declined included titanium, rare-earth metals, lead, silver, zinc, and magnesium. For the second consecutive year, aluminum, produced predominantly from imported bauxite, declined in production, while imports reached record-high levels. Somewhat modest gains were made in beryllium and copper. As has been the case for a number of years, gold was a bright spot in the domestic and internation-al metal mining industry. Gold production was spurred on by the increasing usage and development of heapleaching techniques that make lower grade ores, which were previously uneconomical, profitable. Additionally, various mining companies, the U.S. Mint, individual States, and a number of foreign countries began production of gold bullion and commemorative coins. Gold output in the United States increased from 2.43 million troy ounces (revised) in 1985 to about 3.73 million troy ounces in 1986, a dramatic 54% rise.

Jan 1, 1988

By Christopher J. Vise

Although production operations at mines, representing the extraction and removal of the mined material, often appear to receive the greatest amount of attention, the emphasis given to auxiliary operations is continually increasing. This is due to the changing economic, social, and environmental climate in which modern mines must operate. Auxiliary operations can best be described as those activities that are not directly related to the extraction and removal of the mined material, but must receive proper attention if recovery is to take place in a safe, efficient, and socially responsible manner. In fact, certain mining auxiliary operations, such as strata control and ventilation, are considered to be of such importance that they warrant separate sections in this Handbook. Judging from a mine-personnel standpoint, it is not uncommon for a mine to hire the same number or more individuals responsible for auxiliary operations as the number assigned to production.

Jan 1, 2008

State ownership of mineral in the ground is not newthe Regalian Right is an ancient concept. And the compulsory purchase of land and the minerals beneath it by the State or a body approved by the State (Fitzgerald, 1952) was a principle well established and enforced in practice over a hundred years ago, when such powers became a practical necessity during the period of railway building in Britain and elsewhere:The acquisition of mineral properties which stand in the way of public construction projects still goes on. But in recent years nationalization is being increasingly undertaken as part of the planned use of national resources, for the closer regulation of economic activities, or merely, so it would seem, as a matter of political expediency or national pride. For instance, the unsevered coal in Britain came under State ownership in 1938 in an attempt to simplify a complex pattern of freehold titles which were impedingplanned mining operations. Later, unsevered minerals became a factor in negotiations arising under various town and country planning acts. The acquisition of the Rio Tinto mines by the Spanish Government implies political aspirations. Or State purchase may even be accidental: it was the easiest course for the Sierra Leone Government consequential upon its failure to prevent widespread trespass over legally-held diamond privileges in 1955.This paper has been prompted by problems that have arisen when properties containing unsevered mineral have been expropriated by the Crown in New Zealand: expropriations, it is true, that have been on a small scale in rela...

Jan 1, 1957

By J. Thompson

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree A study into the stability of strike gullies at TauTona mine was to be carried out. In reaching the conclusions to follow, a three-stage process was followed. ?A literature study as well as discussions with management and workers alike to gain their inputs and perceptions. ?An ESH Department survey into the history of transgression from proper mine standard in TauTona strike gullies. Unfortunately records were found to be scarce and obscure and the importance of better inter-departmental recordings cannot be stressed enough. ?An underground survey of 11 pre-selected gullies distributed in both the UCL and LCL reef horizons. This stage is to carry the greatest weight in the points to be brought forward in this report. The process highlighted and ranked the following areas as the most critical role players in the deterioration of strike gullies: ?Poor blasting practice ?Sub-standard siding depth and lead-lags ?Split sets ?Off line gully development ?Adverse geological features. The following has been suggested to the mine to help reduce strike gully instability. ?Where possible, maintain lead-lags below 7 m?else increase the siding depth to suit. ?Decrease the gully width standard to 1.2 m (especially in ?high risk areas?). ?Discourage drillers from drilling side holes in gully face blast pattern. This will allow for time in which tendon support can be kept up to date. ?Ensure split sets are installed 1 m behind the gully face so as to prevent opening up of fractures. ?Utilize the centre split set in the 1:2:1 pattern to maintain the proper gully line. ?When adverse conditions prevail, it is necessary to apply a special support plan not only to the panel face, but also (just as importantly) to the gully as well. Shotcreting of the gully hanging is a suitable long-term consideration for providing the additional a real coverage needed. List of Abbreviations [CL Carbon Leader M/O Mine Overseer UCL Upper Carbon Leader FOG Fall of Ground LCL Lower Carbon Leader H/W Hanging Wall ERR Energy Release Rate F/W Foot Wall WDL Western Deep Levels ESH Environmental Safety and Health ]

Jan 1, 2002

By K. R. Dorman

To develop the potential of precast concrete sets as a support medium in underground mines, a three-piece precast concrete drift set was designed for a small opening and tested to destruction in an underground straining frame. Thirty-six tests were made with three sizes of members using three different loading conditions. In addition, 14 members were tested individually in the laboratory. Test results are compared with theoretical calculations. A cost comparison shows the use of concrete sets would be advantageous where conventional wooden timber requires excessive replacement.

Jan 1, 1968

By Gregory J. Chekan

This Bureau of Mines report presents three methods for designing bulkheads to impound water underground: (1) thin and thick plate design; (2) South African plug design; and (3) single and double bulkhead seal design. Related areas critical to the long-term effectiveness of underground water impoundments are also addressed. These include bulk-head anchorage, concrete specifications and placement, the grouting of permeable strata, and the sizing of barrier pillars. A case study involving hydrostatic tests conducted on a single bulkhead seal constructed in the Safety Research Coal Mine of the Bureau's Pittsburgh Research Center is presented in an appendix.

Jan 1, 1985

By Don Hickey

The MTA in conjunction with LIRR, are in the process of expanding one of the largest commuter railroads in the country, with over 260,000 passengers a day. The LIRR, which provides 700 passenger trains every 24 hours, can?t continue on the present growth course as a joint tenant in Penn Station with Amtrak and NJT. For this reason, in conjunction with the fact that over 53% of LIRR?s current riders into Penn Station are ultimately bound for the East Side of Manhattan opening, have created the need for the expansion of the LIRR. The complete expansion will cost approximately 6.3 billion dollars and all of the contracts are to be completed by 2013.

By Peter J. Coghill, Michael J. Millen, Brian D. Sowerby, Kirby D. Cunningham

"CSIRO Minerals has developed an integrated particle size analysis system for deployment in the grinding circuits of minerals processing plants. The system includes a slurry sampling station, a de-aeration tank and an ultrasonic particle size analyser (UltraPS). The UltraPS analyser is based on ultrasonic attenuation and velocity spectrometry combined with gamma-ray transmission. The technology is applicable to the measurement of 0.1 to 1000 µm diameter particles directly in highly concentrated slurries without dilution. The analyser incorporates a gamma-ray transmission gauge utilising an ultra-low activity radioisotope source that is exempt from International Atomic Energy Agency (IAEA) and Australian licensing regulations.The UltraPS analyser consists of a submersible probe and an electronics package. The probe can be immersed directly in a minerals processing plant stream if the aeration level in the stream is low. For applications where a de-aerated slurry stream is not available, CSIRO has developed an integrated system that includes a sampling station, a de-aeration tank as well as the UltraPS analyser itself. A schematic drawing of the continuous flow gravity fed system is shown in the figure. A commercial sampling system is used to supply slurry at a rate of 2.5m3/hr to the deaeration tank. The aim of the de-aeration tank is to remove air in the slurry to a level where meaningful particle size measurements can be performed. The tank volume is about 0.2m3, thus giving the slurry flowing through the tank a mean residence time in the tank of approximately five minutes. Tests at a number of concentrators have shown that five minutes is sufficient time for slurry to de-aerate to a level where ultrasonic measurements can be made. The tank incorporates an ultrasonic level detection sensor and flow to the deaeration tank is adjusted based on the level of slurry within the tank. The UltraPS probe is mounted through a flanged section of duct, which is bolted to the bottom of the de-aeration tank."

Jan 1, 2003

This paper reviews the current techniques employed in the prediction of subsidence and how they have been applied to partial extraction systems. The method using influence functions to describe the shape of the profile is investigated in detail and has been adopted to model the subsidence over workings in Huntly. It is compared with the profile methods developed in the United Kingdom and found to predict the subsidence profile more accurately than these methods.

Jan 1, 1991

In-pit crushing and conveying (IPCC) is being increasingly considered as an alternative to traditional truck-shovel mining methods. The move towards IPCC is driven by a number of factors including the potential to reduce greenhouse gas emissions, the availability of skilled labour and the need to increase extraction rates to levels that present significant challenges to traditional methods.When considering the relative performance of IPCC and truck-shovel methods, the outcome can be inadvertently impacted by either the use of different simulation approaches, or techniques that do not adequately model the processes in sufficient detail.A simulation approach is proposed that models both IPCC and truck-shovel using the same software platform and is capable of functioning at a wide range of resolutions from life-of-mine scale through to second-by-second asset tracking level. The simulation framework also holds models of processing equipment and hence the mining simulations can be extended to gauge the impact on downstream plant.The approach, known as mine-process operational simulation (MPOS), can be tailored to the level of information available and hence the type of study required, ie order of magnitude, prefeasibility, feasibility, or detailed design.Using information from block models and a range of detailed equipment and process models, MPOS can span major system discontinuities, typified by the mine-plant interface, to allow the estimation of final mine and plant product specifications.

Dec 6, 2010

By Dennis Nottingham

Spin-fin pipe piles can develop large loads in tension, thus have evolved as a foundation product of great potential. Currently, over 500 spin-fin piles have been used successfully in dolphins, docks, buildings and bulkheads. Spin-fin piles are pipe piles with plates welded near the tip at a batter-in-screw fashion. Thus, as the pile is driven, the pile screws into position. Tests show this pile type to have highly unusual stress/strain relationships, wherein plunging failure is usually never reached either at normal or large deformations. Tension capacity can approach pile capacity in bearing; thus, large reserves are usually available for tension. Tests have been performed on 8-5/8-inch to 24-inch-diameter piles in silt, sand, and gravelly soil, to provide a broad spectrum of data.

Jan 1, 1990

By Jogeshwar P. Singh, Aser I. Abbas, Mohamed Ashour

The presented methodology predicts the pile head response (i.e. pile head load - displacement curve) and develops the load transfer (t-z) curve of piles in sandy soils under tension forces based on soil/pile properties and soil-pile interaction. The proposed approach improves the prediction of the t-z curve in sandy soils compared to current practice. The method employs a nonlinear soil constitutive model to calculate the mobilized shear stress/strain in soil at the soil-pile interface induced by pile upward displacement. The approach accounts for the influence of the pile slenderness ratio on the predicted t-z curve and is validated through comparisons with measured pile head response and t-z curves from full-scale pile load tests. INTRODUCTION Piles may be subjected to axial uplift forces due to either static loading or cyclic loading. The majority of methods are only concerned with the pile ultimate tensile capacity. However, the mobilized pile stiffness (i.e., pile-head load-displacement relationship) is essential to determine the interaction between the foundation and the superstructure and consequently the performance of the whole structure. Methods that assess the pile ultimate tensile capacity usually assume the failure surface at the soil-pile interface and estimate the local side shear resistance using a lateral earth pressure approach. The Naval Facilities Engineering Command (NAVFAC 1986) and the US Army Corps of Engineers (USACE 1991) employed Eq. 1 to assess the ultimate shear stress (τ) developed at the soil-pile interface.

Jan 1, 2018

By Vincent A. Scovazzo

Many accepted and useful methods have been developed and used for pillar design. Each method has its own particular strengths and weaknesses. Three methods addressed in this paper are; empirical, analytical, and numerical. Each of these methods have their place in pillar design. Analytical methods result in close approximation of the ideal pillar (most economical, stable, or yielding) and are suitable for use in final mine design and in analyzing existing problems. BOYD uses the analytical method to develop site specific mine pillars design equations. An analytical method, one of many developed by BOYD, is presented here and is based on the procedure used by Wilson (1) and others in development of their empirical equations.

Jan 1, 1995

By S. T. Reese

STATISTICS of injuries in the quarrying and related industries in the United States first became available when the Bureau of Mines collected reports from the operating companies for the calendar year 1911. Since then reports have been collected annually. The present bulletin, covering the calendar year 1952, is the 33d publication containing statistical data on injuries at quarries and related plants, and it is the first to be published since 1944. The last publication was Bulletin 458, Quarry Accidents in the United States during the Calendar Year 1942. The unpublished statistics for 1942-51 may be found in the Appendix of this bulletin. The Bureau of Mines is authorized to collect data on injuries at quarries, but there is no Federal law that compels operators to supply such data, and the reports received from operators are voluntary responses to the Bureau's requests for information. Although the figures presented herein may not be complete for the entire industry, every effort has been exerted to make them so, and the figures given are believed to be thoroughly representative of the hazards to which quarry workers are exposed. Moreover, the figures are com¬parable as between States -which is significant in view of the lack of uniformity among the States as regards classes of plants covered by State laws, classes of injuries covered by State reports, and other factors that tend to make it impracticable or impossible to compare the injury experience of one State with that of another or to comprehend the relative importance of the various causes of injuries in the industry as a whole.

Jan 1, 1955

By Vidyaranya Bandi, Madhav Madhira, Kota Vijay Kiran

"Using hyperbolic relationships for the non-linear responses of shaft and base resistances, a method is proposed for estimating initial shaft and base stiffnesses and ultimate shaft and base resistances of a pile from pile load test results. An iterative procedure is used to arrive at the values of shaft-soil and base stiffnesses and the ultimate shaft and base resistances. The method is applied to load - displacement data available from pile load test results to illustrate its efficacy.INTRODUCTIONA pile foundation is the most effective and economical solution in transferring large vertical loads to deeper depths. As the pile is subjected to axial load, the soil mass surrounding the pile is vital in providing vertical support for the pile. The nature of pile–soil interaction is three dimensional and to complicate the problem further, response of soil is nonlinear. Finding a closed form solution to such problem is extremely difficult. Several methods were developed to study and predict the response of the composite pile–soil system. Faruque and Desai (1982) implemented both numerical and geometric non-linearities in their three dimensional finite element model. Rajashree and Sitharam (2001) developed a nonlinear finite element model of batter piles under lateral loading using a hyperbolic relation for static load condition and modified hyperbolic relation, including degradation and gap for cyclic load condition.The ultimate capacity of the pile is estimated considering the strengths and unit weights of soil layers with depth, overburden pressure and other relevant parameters. The estimated capacities always need to be validated by conducting initial maintained load test. The estimated capacity may differ with the actual at site since the values of strength, stiffness, interface resistance between pile and soil, lateral earth pressure coefficient with depth and soil stratification, etc., differ from the design parameters considered for estimating the ultimate capacity of pile. The estimation of axial capacity of piles involves considerable uncertainties in selection of appropriate design parameters and the design rules are not always consistent with the installation procedures/processes involved."

Jan 1, 2017