Search Documents

By R. C. Burtan

Long before recorded history, man began to dig into the earth's crust in a never ending search for useful materials. It is well known that more than half of the earth's crust is composed of silicon dioxide (SiO2), also known as silica. Silica and silica-containing material have a great many uses in modern society. This material, however, is potentially an extreme health hazard. Silicosis: Not a New Disease Centuries before the Christian Era, Hippocrates wrote of a lung disease common to those who mined in hard rock. He was obviously describing silicosis. It is also apparent from ancient writings that the Egyptians were aware of this malady. Dioscorides also wrote on this subject in the fifth century B.C. It is undoubtedly the oldest and best studied of the occupational lung diseases. Silicosis was certainly described by Agricola in his De Re Metallica published in 1556. Here he described lung disease among hard-rock miners. The original document was written in Latin and then translated in 1912 by Hoover and Hoover. One of these translators was Herbert L. Hoover, a former US president who once made his living as a mining engineer. More recently, there are numerous references in medical literature in the 19th and 20th centuries relating silica exposure to silicosis. There are specific references to mining in hard rock, as well as to sandblasting and a host of other industrial exposures. In 1919, Winslow described standards for measuring the efficiency of exhaust systems in polishing shops using sandblasting. These standards were equally applicable in the mining industry. As early as 1920, Winslow explored the efficiency of certain devices used to protect sand-blasters against the dust hazard. These devices were equally applicable in the hard-rock mining industry. The medical community recognized the silica health hazard in the early 1900s. Middleton described the illness in the British Medical Journal in 1929. He noted the danger to health at that time. D. Hunter mentions in his book, The Diseases of Occupations (1969), the monumental work of Merryweather in 1936, in which he surveyed the silicosis risk in Great Britain. He showed statistically that the average employment length of sandblasters who ultimately died of silicosis was 10.3 years, compared to 40.1 years for all fatal cases, irrespective of occupation. Sandblasting and hard-rock mining and drilling, obviously, are very hazardous occupations. Weil and Zisking of Tulane University wrote in 1975 that "it was known as early as 1935 that the course of silicosis is much more rapid in sandblasters than in miners or foundry workers. This can be explained by the fact that sandblasters are exposed to an almost pure siliceous dust containing high concentrations of respirable particles within the range of 1 to 3 micron size." Protecting the Worker The medical community recognized in the early 1900s the need for proper protective equipment for all of those who worked with siliceous materials. Middleton, writing in 1929, said: "The worker is then protected by a close fitting helmet with an air feed, much as in the case of an underwater diver. In spite of these precautions, cases of silicosis among sandblasters are being met with today. It is a matter for serious consideration whether a substitute, such as steel or iron grit, could not be used to replace the siliceous grit as the abrading material." C. E. A. Winslow, a professor of public health at Yale School of Medicine, and others wrote of the need to protect sandblasters by

Jan 7, 1984

By Louise Pearce

?Environmental and social impact assessments (ESIAs) are: ??process-driven and scientific processes ??The process entails a number of steps and procedures which result in obtaining a licenceto operate ?and moving more towards a social license to cooperate. ?However, the primary premise of ESIA is to facilitate the consideration of environment and the communities in planning and decision-making which would ultimately make it possible to arrive at decisions that are ?sustainable?. ?Hence, ensuring the development of the mining sector on a sustainable basis is a critical challenge that needs to be addressed by the global community.

May 1, 2011

By A. F. Roberts

The subject of mine fires is a very wide one. To give reasonable coherency, the paper concentrates on the behaviour of fires in the ventilated airways of mines; spontaneous combustions are not considered. The following topics are considered in some detail: 1) Material selection: Performance requirements for mining materials in terms of flammability and smoke/fume production; methods of test and need for relevance to mining conditions. 2) Fire growth: The influence of material properties and method of use on the rate of growth of fire in a mine roadway; the influence of ventilation, slope, material orientation, proximity of walls and roof on fire behaviour. 3) The fire in the ventilation network: The influence of fire on the ventilation distribution; the circulation of fire products in the network. The influences of these topics in determining fire control strategy are then considered but topics such as fire detection and fire extinction methods are not reviewed in detail. An extensive Bibliography on papers relating to mine fires is included.

Jan 1, 1989

By Ryan L. Veenstra

This paper presents a modelling study of a cemented paste backfill in an underground stope. The model was developed to help provide a better understanding of what is happening in the stope during the filling stage of the stope. In order to do this, the model incorporates the paste rise rate, stope geometry, and time-dependent input parameters. This paper looks at the effect of geometry in two parts. The first part compares a series of simple rectangular stope models. These models differ in size both in two and three dimensions. The second part compares the results of four 2D models together and then to the field instrumentation data. Part of this section introduces the geometry and instrumentation within the test stope.

Jun 1, 2012

By P. L. Michael

Several evaluations were made by Modified Rhyme Test (MRT) word lists transmitted through various simulations of the Trapped-Miner Communication System being developed by the U.S. Bureau of Mines. The tests were performed in a "single blind? situation so that the evaluators would not be biased by knowing the characteristics of the system being simulated. A computer program was developed to provide a simulation of the electrical aspects of the communication system and to provide an evaluation by calculation of the articulation index (AI). The study indicates that communication through the presently proposed system will be somewhat unreliable at depths as great as 300 metre even with the system operating at maximum effeciency.

Jan 1, 1977

By Adilson Curi

"A fundamental aspect in the development of any open-pit mining project is the determination of the mineable mineral reserves, obtained with the design of the so-called ultimate pit limits. In this paper, firstly the Vulcan software applied over the data of MR phosphate deposit will be introduced. Modeling of the ore deposit has been done by geostatistical and conventional methods by using geological data of 41 diamond core samples. Insitu geological reserves were estimated to a level of accuracy to support detailed mine planning. Ore body has been divided into regular three dimensional fixed blocks. The ultimate pit limits of the model deposit weredetermined by the vulcan program by an optimizing technique. Additionally, the approximate location of the deposit and drillholles and the contour map of the ultimate pit limits generated by the vulcan program are presented. "

Jul 17, 2000

This report is in partial fulfillment of Contract S0241051 awarded to COMINEC on June 27, 1974. 'Me purpose of the work under this contract is to develop a conceptual design for an automated longwall mining system. The conceptual design will serve as the basis for future design and development of an automated longwall mining system capable of sustained production in excess of 2,500 tons per shift with reduced manpower which will ultimately be demonstrated in an area where conventional longwall mining has been successful. 1.2 DEFINITION OF THE PROBLEM 1.2.1 Why An Automated System The most obvious benefit of automation and remote control in a longwall mining system is the reduction of accidents consequent upon a reduced working force in the hazardous face areas. However, another important aspect of the problem is the skilled labor shortage which is being compounded by the need for vastly increased coal production. The United States coal mining industry had a working force of almost 600,000 miners in 1928 but was able to muster only 145,000 miners in 1970. The miners required to staff the additional working sections and the new mines necessary to meet our energy needs are simply not available. Only automation and remote control will permit a reduced work force with increased production by keeping the face equipment operating continuously.

Jan 1, 1975

By A. M. Hanna

This paper presents the experimental investigation on the ultimate skin friction of batter piles. The model piles were pushed in medium dense sand deposits at different inclinations up to 30 with respect to the vertical and tested under axial compression loads. The decrease in the total skin resistance with increasing pile inclination can be explained in terms of the reduction of the ave­rage mobilized angle of friction between the pile shaft and sand. The analysis, which takes into account asymmetrical earth pressure distributions around the pile shaft, showed good agreement with experimental results.

Jan 1, 2010

By J. Warmbrodt, D. Apel, D. Nutakor, L. Grayson, M. Hilgers

MinerSIM is an augmented reality system with integrated hypermedia that is suitable for training underground miners in the basics of using a jackleg drill to install rock bolts. While statistical evidence shows that rock bolting with such a drill has an inherent level of risk, it is conjectured that this can be mediated with adequate safety training outside of the actual mine environment using a variety of educational media including interactive three-dimensional images, games, animations, and videos to describe the mechanics of rock bolting and its principles. Ultimately, trainees will install rock bolts in an immersive environment mixed with real and virtual images generated via a gaming graphics engine. This paper will discuss considerations, implementation issues, and evaluation methodologies of the MinerSIM system.

Jan 1, 2007

By Kjell Karlsrud

"Abstract New semi-empirical design procedures for the determination of ultimate shaft friction and load-displacement response of axially loaded piles in clay are proposed. Hereunder also prediction of how the capacity will build up with time following the pile installation, primarily as result of reconsolidation. A main basis for developing the new procedures was detailed review and re-assessment of results from a series pile load test programs published over the past 30 years on piles well instrumented to monitor soil- and pore pressures as well as load distribution along the pile shafts. Two new alternative procedures are proposed for predicting the ultimate shaft friction; a-approach using the normalised undrained strength based on direct simple shear tests as a main correlation parameter, and ß-approach using the overconsolidation ratio, OCR. Both approaches include the effects of the plasticity index of the clay, Ip, which is shown to have an especially large impact on the correlations when Ip<25. It is recommended to use both methods in design practice, and select design values for the ultimate shaft friction that represents an average for the two methods. Pile diameter, length or stiffness, or whether the pile is open- or closed-ended seem to have little impact on the shaft friction. However, a moderate effect of pile length or flexibility on the total ultimate pile capacity comes out of the proposed t-z curves, which include some post-peak reduction. The proposed procedure for predicting the time for set-up is based on linear radial consolidation theory. The main input parameters are the insitu permeability and virgin modulus number (or virgin compression index) of the undisturbed clay. The same basic formula and correlations are applicable to both open and closed-ended or partially plugging piles.IntroductionThe design procedures presented herein are primarily based on observations and data collected in connection with “fully instrumented” pile testing programs that the author has been responsible for or has become involved with over the past 40 years, or that have been found in the literature.It was a pre-requisite for the test programs included that there were sufficient high quality soil data available to give a reliable determination of the true in-situ strength and compressibility characteristics of the clay deposits. The soil conditions range from soft NC clays with undrained shear strength down to about 15 kPa, to very stiff clays with undrained shear strength up to about 500 kPa and OCR up to 25. The plasticity index of the clays mostly lies in range 12 to 60 %."

Jan 1, 2014

By B. P. Watson

The first crush pillars on the Bushveld platinum mines were introduced at Union Section in 1978. Before the introduction of crush pillars, serious problems were experienced when stoping advanced to a point 30 m to 40 m on both sides of the centre gully. At least three to four stopes were collapsing per month. The introduction of the pillars stopped the stope collapses in the mining area where they were introduced. The residual stresses of these pillars were never measured; however, the successful elimination of the ?back-break? problem suggests that the original pillars had a residual strength of at least 8 MPa. Apart from back analyses, very little work has been done to determine the residual strength of crush pillars and only very recently have any measurements been made. The lack of knowledge in this field has resulted in pillars being designed based on experience. Concerns about stope collapses, similar to the Coalbrook disaster, have led to larger pillars being cut in more recent times. If such pillars were cut in brittle quartzites they would always fail violently but the ductile nature of the Merensky Reef generally allows large pillars to fail without bursting. Occasionally, however, one would burst in a working area. Increased incidence of bursting has been reported on some mines at deeper levels but most of these bursts occur in the back areas. Nevertheless, the incidence of bursting increases the risk of falls of ground in already dangerous areas, and the larger pillars decrease the extraction ratio. This paper describes the evaluation of stress measurements conducted in two boreholes over a crush pillar with dimensions 2.5 m x4.0 m, and a height of 1.2 m. Boussinesq equations for vertical and shear stress were used to analyse the original measurements and provide a stress profile across the pillar as well as the residual strength of the pillar. The results showed an unexpectedly high peak stress of 280 MPa at the centre of the pillar and a residual strength of 48 MPa. The reason for the high residual strength is suspected to be the result of the stiff environment under which the pillar failed and the small height of the siding on the up-dip edge of the pillar. More measurements should be conducted on several mines to establish a range of residual strengths for narrow crush pillars.

Jan 1, 2008

By Ronald M. Hays

The Duluth Gabbro Complex in Northeastern Minnesota possibly contains a significant domestic copper resource and the nation&apos;s largest nickel resource. Exploration has discovered large low-grade copper-nickel (Cu-Ni) deposits between Hoyt Lakes and the Boundary Waters Canoe Area (BWCA). The mining and processing of Cu-Ni will have environmental, economic, and social impacts. The purpose of this study is to relate major environmental, economic, and social considerations to various aspects of Cu-Ni extraction. An open pit and two underground (block caving and open stoping with backfilling) models were developed to generate information on the impact of Cu-Ni extraction. Important considerations having environmental, economic, and social impacts (luring various aspects of Cu-Ni extraction are identified and defined. These aspects are exploration, development, mining, beneficiating, smelting, transportation, and termination of operations. Considerations are grouped into the general categories of site, industrial, energy, climatic, resource, water, air emission, waste disposal, employee, tax and royalty, transportation, and community considerations. Cu-Ni extraction in Northeastern Minnesota presents major environmental, economic, and social risks. Decisions are required on trade-offs between adverse and beneficial impacts. The approach used in this study assists in assessing environmental, economic, and social impacts. It will aid in the examination of potential and projected short-term and long-term advantages and disadvantages and will aid in the development of Minnesota&apos;s Cu-Ni resource for the maximum benefit to society.

Jan 1, 1974

By Mehmet Guney

At the Armatcuk mine in Turkey, various modifications of sublevel methods have been tried during the last decade in an effort to eliminate gob fires, dangers from roof falls, and surface subsidence, and also to increase extraction efficiency. From the experience thus gained, it was decided that the most likely system to give maximum benefits, considering the existing geological conditions and coa1-seam characteristics, was hydraulic stowing. This paper examines trends in the working techniques of hydraulic stowing and discusses the favorable results and technical problems that the method produced at Armutcuk. The Armutcuk mine, a subsidiary of Eregli Coal Mines (EKI), produces 1300 tons of run-of-mine coal daily from thick (about 10-90 ft) and highly dipping (about 50-90°) coal seams. The coal is highly volatile with good coking properties that make it highly suitable for industrial use. Most of this coal is used in the iron and steel industry at Eregli on the Black Sea coast. Complete recovery of the coal is of vital importance to industrial development and progress. Initial coal extraction was carried out by means of a sublevel mining system modified to accommodate local geological conditions and coal seam characteristics. This method is similar to that employed in metalliferous mines. Several problems arose from the application of the method, one of them being the prevalence of gob fires which caused periodic shutdowns in some sections. To achieve maximum coal extraction with minimum dilution, to eliminate gob fires and surface subsidence, and to reduce fatal accident rates, a decision was taken to change from this method to a hydraulic stowing system. The pres- ence of large deposits of conglomerate and sandstone on the surface contributed to the decision to employ this new method. Although hydraulic stowing practices have been carried out in America and Germany, Upper Silesia may, so far as coal is concerned, be considered the birthplace of the method. Here the process was adapted to thick coal seams on a large scale to reduce dangers from gob fires and damage from surface subsidence. Today, the mining system is not only widely used in the coal mines of France, the Saar, India and Poland, but has also been successfully applied to the iron ore and potassium salt mines in Russia and Germany. LOCATION AND HISTORY The Kandilli-Armutcuk coal field, the most western outcrop of the North Anatolian coal basin, extends for five miles along the Black Sea coast (Fig. 1). The Armutcuk Mine is situated on the southern boundary of the coal field about 40 miles from Zonguldak and about 12 miles from Eregli. The history of coal mining in the North Anatolian coal basin goes back more than a century. Mining commenced on a small scale in the Kandilli-Armutcuk coal field in the late 1880&apos;s, and from this time until nationalization in 1940 the mines were operated by private Turkish and foreign interests. In 1940, Eregli Coal Mines was established to takeover the management of these enterprises. The Armutcuk Mine was developed for the first time in the mid-1940&apos;s. Since then it has been in continuous production and it now produces an annual 440,000-ton run-of-mine output from which 320.000 tons of salable coal is obtained. MINE GEOLOGY The carboniferous inlier of the Kandilli-Armutcuk coal field crops out over an area about three miles long and one mile wide. The major part of the inlier consists of the Namurian formation with only a relatively small area of Westfalian-A visible on the surface (Fig. 2). The Namurian formation, which has no exploitable coal seams in the Armutcuk Mine, consists mostly of arkose sandstones and black shales often having

Jan 1, 1969

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

The purpose of this study is to formulate practical guidelines for active underground mining in close proximity to water bodies. This was accomplished through systematic completion of three phases of study: I) Collection and Documentation of Data; II) Application of Existing Guidelines to Case Histories of Previous Inundations; and III) Development of Recommended Guidelines for Underground Coal Mining Near Bodies of Water. Phase I of the study involved a worldwide data collection effort designed to obtain foreign and domestic guidelines for mining near water bodies, and accident records and case histories of accidental mine inundations. Within Phase II, existing guidelines were categorized and classified and then evaluated as to their effectiveness in precluding past inundations had they been in effect at the time of inrush. Advantages and disadvantages of existing guidelines were defined. Drawing on the broad data base established in previous study efforts, Phase III was directed at development of viable guidelines to promote the greatest possible coal extraction while precluding accidental mine inundation. Two levels of guidelines are presented; Level I Guidelines require little or no subsurface exploration on the part of the mine operator, while Level II Guidelines recommend various testing and investigative procedures to permit greatest possible mineral extraction. This report presents findings and conclusions of the study.

Jan 1, 1976

By L. Tonc

In 2004, the engineers at the Deer Creek Mine located near Huntington, Utah initiated the ventilation planning to exploit a remote area of the mine?s reserves. This area was located under a mountain which would not allow for the incorporation of an additional shaft or portal access near the proposed longwall panels. With this constraint along with the desire to maintain a two entry gate road system and the expected condition of frequent coal wash outs a ventilation plan was established. Different options were examined that included; increasing the current exhaust fan power, adding another exhaust fan installation, converting the ventilation fans in the active portion of the mine to a forcing system, and modifying the ventilation system in the active area of the mine to a push-pull system. The push-pull ventilation system was ultimately selected. This paper details the design process of the ventilation system upgrade, the procurement process for the new fans, and the new fan startup testing.

Jan 1, 2009

By J. R. Hamke

THE WILLISTON basin is the largest known sedimentary basin on the North. American continent. Two-thirds of this large basin lies within the United States in Montana, North Dakota, and South Dakota. Less than 10 years after the first commercial oil discovery in North Dakota in 1951, the petroleum became one of the largest industries in the three-state area. Crude petroleum is now the most valuable mineral resource in the area. In 1960, the basin produced 39 million barrels of worth $100 million at the wellhead. Most of the 137 oil pools covered to date are in Paleozoic carbonates at depths ranging from 3,000 to 13,000 feet. The major producing fields, centered on the Cedar Creek anticline in Montana and the Nesson anticline in North Dakota, produce from depths below 6,000 feet. This report presents descriptions of all phases of the Williston basin petroleum industry, including leasing, exploration, geology, drilling, production, transportation, and refining. Engineering, physical, and production data, maps, and crude petroleum analyses for 137 separate oil pools are included.

Jan 1, 1966

By Marlion T. McQuinn

This paper will discuss the design, construction, and performance of the support of excavation on the Dulles East and West Automated People Mover Tunnels and Station projects. The elements of the system included drilled soil nails and rock anchors with reinforced shotcrete to the excavated face. We will discuss the geotechnical characteristics, design and construction considerations, loading criteria, construction techniques, schedule constraints, and performance of the support of excavation system. In consideration of the conference theme, there will be a discussion of the application of the real-time instrumentation monitoring program. The project team worked to design and install approximately 710,000 square feet of shotcrete and 19,000 soil nails/rock anchors as well as excavate over 720,000 cubic yards of rock materials within 15 months and in such a manner as to minimize the disruption to airport passengers and operations.

Jan 1, 2006

By C. E. Dobbin

The coal fields of Montana are widely distributed through the plains region in the eastern and northern parts of the State, and the mountain regions in the central, southern, and southwestern parts of the State. (See fig. 1.) SURFACE FEATURES The Fort Union region in eastern Montana is a broad plain of almost horizontal rocks, characterized by extensive "bad lands" along the larger streams and by red hills, benches, ridges, and buttes which represent shale and sandstone that have been fused by the burning of an underlying coal bed.

Jan 1, 1932

By S. K. R. Iyengar

This report presents the results of a study to develop optimal designs for light-weight mine roof supports for use in underground coal mines. A load capacity of 196 kN (22 tons) and a height adjustable between 1.829 m (72 inches) and 2.438 m (96 inches) were taken as the design parameters and the design goal was a unit weighing less than 22.3 kg (50 lbs). Three alternative design concepts were explored, viz. mechanical, hydraulic, and hydro-mechanical and a total of 13 designs analyzed in detail. Steel, aluminum alloy and composites were the main potential construction materials investigated for suitability from structural, life, and safety and other considerations. The designs considered most promising for development were: (i) the mechanical screw-pin type using telescopic tubes and a fine adjustment screw thread section (ii) the all-hydraulic type, of steel, aluminum alloy or aramid graphite construction (iii) the hydro-mechanical design using telescopic tubes and a short stroke hydraulic cylinder for fine adjustment It is shown that by using realistic mathematical models for stress and deflection calculations, it is possible to reduce prop weight to the design goal. The analysis presented for all-hydraulic props is applicable to hydraulic cylinders on all mining equipment and similar machinery. This report includes the computer program and user&apos;s guide for analyzing hydraulic cylinders as well as a cross-indexed bibliography on structural composites.

Jan 1, 1978