Search Documents

By C. M. Egert, S. Rajic

"We have developed a monolithic micro-spectrometer suitable for a variety of sensing applications including industrial process monitoring. The device consists of a solid structure with a volume less than 6 cubic centimeters. All optical components of the spectrometer including two aspheric mirrors, a diffraction grating, and entrance and exit surfaces are fabricated onto the surface of the structure. All light paths are internally contained within the structure. The result is a small, rugged spectroscopic sensor ideally suited for use as a process monitor. Due to its monolithic nature the device requires no post-fabrication alignment; nor can it be knocked out of alignment during use. Although many materials and thus wavelength regions were possible, the prototype device discussed here was produced in PMMA by precision diamond turning. However, lower cost manufacturing approaches involving injection molding are under development to produce an affordable sensor.Due to its rugged monolithic design, small footprint, and low cost the monolithic micro-spectrometer is ideally suited for distributed monitoring applications often required for industrial processes. It is expected that modified versions of this sensor designs will be required for specific applications so as to maximize the performance and resolution over the operating range. For example, the prototype device described here operates over a wavelength range of 500 nm to 1000 nm. The performance of this device as a real-time surface monitoring sensor will be discussed in detail. Our approach of using wavelength dependant scattering resulted in the reduction to practice of a miniature, monolithic, rugged, low-cost, micro-instrument in a sensor sized package. The process sensor applications community has been faced by the cost versus performance issue. Simple go/no-go sensors are typically inexpensive but they provide very limited and sometimes dubious data. Scaled down traditional instruments offer very good measurand information but are typically cost prohibitive, fragile, and still relatively large. This work will bridge the gap between these two extreme sensing alternatives."

Jan 1, 1997

By Seung-Chul Lee

Transparent conducting tin(1V) oxide thin films have been studies and developed for the electrode materials of solar cell substrate. Fabrication of tin oxide thin films by sol-gel method is process development of lower cost photovoltaic solar cell system. The research is focused on the establishment of process condition and development of precursor. The precursor solution was made of tin isopropoxide dissolved in isopropyl alcohol. The hydrolysis rate was controlled by addition of triethanolamine. Dip and spin coating technique were applied to coat tin oxide on borosilicate glass. The resistivity of the thin film was lower than 0.18-cm and the transmittance is higher than 90% in a visible range.

Jan 1, 1999

By Donald R. Sadoway

The viability of treating certain forms of hazardous waste by direct electrolysis in molten oxides is under investigation. Secondary residue or waste mud produced in the course of chromate chemical production is the focus of attention in this study. The goal is to reduce the water soluble hexavalent chromium either to insoluble trivalent chromium or to chromium metal. Electrolysis tests have been conducted in a high temperature cell containing chromate sludge dissolved in an electrolyte composed of Al2O3, SiO2, CaO, and MgO. Oxygen production on a carbon-free anode has been confirmed.

Jan 1, 1992

By Gary K. Elliott

Many industrial processes generate hot waste gases which contain particulate pollutants. Conventional clean-up techniques suffer limitations either because collection efficiency is low or because the gas must be cooled before treatment. thereby increasing costs and preventing energy recovery. The application of increasingly stringent environmental legislation to the non-ferrous metallurgical industry is presently illustrating these conventional technology limitations. Low density ceramic media allow filtration to ta,ke place at 'high temperatures and are now rapidly becoming accepted In many industries. This paper reviews experiences with a proprietary low density ceramic filter element. CerafH. It includes consideration of the structure, composition. typical operating and case studies with particular reference to non-ferrous metallurgical furnace applications.

Jan 1, 1992

By Dongping Duan, Hongliang Han, Li Zhong, Siming Chen, E Zhou

In this study, physical, chemical and microscopic characteristics of Celestine were investigated firstly. Based on which, the thermodynamic analysis of Celestine reduction was discussed. And the experiments of Celestine carbon-containing pellets used in rotary hearth furnace process were studied. The results showed that it is feasible to deal with Celestine by rotary hearth furnace direct reduction process. When the temperature is 1200°C, C/O ratio is 0.8 and holding times is 20min, the conversion rate of SrSO4 in Celestine is above 95%, the utilization rate of Celestine is nearly 100%. This study can provide theoretical and technical basis on economical and rational use of Celestine.

Jan 1, 2016

By Yuan Lu, Yiming Rong, Richard D. Sisson Jr

With the development of quench technology, there is a trend of using gas quench to replace liquid quench for less distortion and residual stress. The fundamental difference between the liquid and gas quench is the heat transfer coefficient, not only the values but also the shape of the curve as a function of temperature. The equivalent heat transfer coefficient for the liquid and gas quench is analyzed by simulations and experiments. Even it may result in the same hardness in the liquid and gas quench, the steel microstructure may be different because of the different cooling processes, and therefore other steel properties, such as toughness, may be different. The cooling process, microstructures and properties such as hardness and toughness should be examined when designing the liquid or gas quench processes.

Jan 1, 2015

By Vadim J. Jabotinski

This paper describes several areas of application for electron beam processing of materials. The technology and use of electron beam systems in gas phase synthesis reactions are described. Gas phase reactions may be used to generate ultra- fine metal or ceramic powder that are very pure and crystalline. Among the examples presented are: the generation of nanometer sized metal powders and the gas phase synthesis of silicon carbide for silica and methane. The experimental system is described and future theoretical and experimental objectives are identified.

Jan 1, 1998

By T. Alboussiere, O. Paireau

"We have designed an experiment to simulate natural convection in a direct-chill aluminium ingot. In this experiment we induce natural convection within a hemisphere filled with liquid-metal (mercury). The device consists of a copper hemispherical bowl closed by a copper plate. The top is maintained at superheat temperature while the boundary is cooled. While the temperature measurements were found using thermocouples, the velocities were obtained using an original technical procedure that relies on MHD properties. By applying a steady local magnetic field, we measure the velocity. The distribution of temperature and velocity can be separated into a thermally stratified core bounded by thermal wall jets. These wall jets greatly influence the degree of macrosegregation in ingots.1. Natural Convection in Aluminium CastingIt is well known that the quality of the final product in aluminium casting depends on the movements within the liquid metal such as forced or thermogravitational convection. Strong buoyancy-driven flows are known to occur in the liquid metal pool of an aluminium ingot caster. These flows have a significant influence on the metallurgical structure of the ingot through the redistribution of heat, fragmented dendrites and segregated material within the pool. Macrosegregation mechanisms depend on favourable temperature and flow distributions in the sump, and these factors will determine the pattern and degree of macrosegregation. Moreover, for many years, the importance of thermally-driven natural convection in casting has been underlined (Cole & Bolling, 1965). In this way, a precise determination of the velocity and temperature fields is required in order to improve understanding of the macrosegregation mechanisms. That is precisely the aim of this paper, which provides experimental data of the flow and the temperature distributions in a natural convection experiment. We intend, with this laboratory experiment, to determine accurately the velocity field, particularly within the thermal boundary layer where the effects of the flows may have an important role in the transport of crystals."

Jan 1, 1999

By A. MacRae

Campaign life of the converting furnace has been limited by break-outs through the hearth and walls. Throughput of concentrate has increased by 60% since start-up of the copper operations in 1981. The Furnace Integrity program was initiated at Kidd in 1993 to improve the reliability and safety of the smelting-cleaning-converting furnace line. The converting furnace is undergoing a series of upgrades to overcome severe refractory wear to the roof, walls and hearth. A recent shut-down was held in March 1997 to implement improvements to the roof, walls and slag outlet. Wall modifications included a new upper shell, wall coolers which can be supported during a shut-down from outside of the vessel, and an increase in the number of cooling blocks. Improvements to the roof included increased cooling, a novel brick/cooler suspension system, and roof compression for gas tightness. Design is currently underway to deepen the refractory hearth, to decrease hearth erosion and increase resistance to flotation.

Jan 1, 1998

By Aïda Espinola

This work is part of a research program concerning the study of heavy metal removal and selective recovery from electroplating waste waters in the Guanabara Bay ecosystem, preventing the potential noxious retarded effect of landfill, specially in a country of heavy rainfall. A flow-throw cell was employed to adapt to the limits established by the local legislation for disposal in rivers and seas. The cell design is presented and preliminary results show that this cell may be applicable for the decontamination from copper.

Jan 1, 1994

By Z. Sadowski

The influence of organic acids simple salts and A. niger saccharose and molasses worts on sodium oleate adsorption on the salt-type mineral surfaces has been studied. It was found that salts of organic acids had an effect on the sodium oleate adsorption on barite calcite and magnesite. The collector adsorption on the barite and calcite surfaces decreased under the influence of investigated worts. Experimental data suggest that the biomodification of salt-type mineral surfaces can be used for the selective separation of these minerals.

Jan 1, 1991

By Min Chen

A numerical simulation of the stress field of the solidified shell in the mold during continuous casting of peritectic steel slab was calculated with commercial software. The results showed that the maximal stress on wide face of the solidified shell was located at the corner and near middle of the slab, and it increased with increasing the width of slab. In addition, the stress was also influenced by operating parameters such as superheat degree, drawing speed and cooling intensity of the mold, and the maximal stress value and its position changed with these parameters. For the slab with section size of 3200mm×150mm, the proper drawing speed was around 1.2m/min, with cooling intensity of 5500L/min while the superheat degree was 15°C to 25°C in order to prevent longitudinal crack occurring during peritectic steel continuous casting.

Jan 1, 2009

By Onwukamike, Onyedika G. O, Ogwuegbu M. O. C., K., Onyenehide C

A detailed mineralogical and elemental characterization of a lead (Pb) ore deposit from Ishiagu, Ebonyi State, Nigeria was carried out with XRD, SEM-EDX, and ICP-OES based mappingtechniques. The results show that the most dominant and valuable metal is lead (Pb = 95.02%, mass fraction). The main mineral is galena. Ilmenite and sphalerite occur as minors, which account for 2.71% and 0.80% respectively. Elements like Al, Ca, Mg, Ti, Na, Mn, Si and Sn occurred in trace amounts and are disseminated in the entire ore body.The surface and interrelations of the crystals were examined with x-ray mapping and the result shows the pattern of dissemination of the minerals within the ore body.

Jan 1, 2015

By Richard B. Stein

Bechtel's BEMSIM computer program is a useful tool for solvent extraction-electrowinning plant design optimization. Its power (up to 90 stream components, 240 process streams, 180 process steps) has been applied to investigate floweheet configurations in order to perform basic engineering, sizing of plant equipment and to optimize performance of commercial-size copper plants. Flowsheet variations presented include series, parallel and series-parallel extraction stages, while heat balances simulate operations in summer and extreme winter conditions. The BEMSIM program has also been applied to nickel-cobalt, gold and manganese extraction.

Jan 1, 1993

By Aarne Kopanen

In recent years, various renovations have been carried out in the production chain of the Outokumpu copper refinirg process. The anode casting shop, which is the final integral production section at the Harjavalta copper smelter built in its original form in 1945, was fourxl unsuitable for technical and capacity demads during longer periods of operation, and a new casting shop was built in 1974. The electrolytic copper refinery of Outokumpu Oy at Pori was built in 1941, and subsequently expanded in two stages. Even with its present limited scale of production it has been fom important to mechanize the main operations. This work was started in 1967 with the design and construction of the starting sheet machine connected with the cathode washing and unloading machine as a combined unit. Mechanized treatment of anodes has gained advantage particularly from the new design of a highly automated anode casting shop. In the further development of the mechanization a stripping machine for, starting sheets was designed and installed, starting operation in 1974.

Jan 1, 1976

By Andre Thess, Jurij Kolesnikov, Christian Karcher

"During the motion of molten metal under external non-homogeneous magnetic field the induced electric currents produce Lorentz body forces in the opposite direction to the flow, causing deformation of velocity profile, vortical structures, and adding a pressure drop across the magnetic field. The same Lorentz force acts on the magnet system. We analyse these phenomena in metallurgy, namely, at molten metal pumping, stirring, continuous casting, and in contactless Lorentz force flowmeter (LFF). Experiments with liquid metal alloy, including direct measurements of Lorentz forces, velocities, and flow structure visualization were conducted. Based on this study the industrial prototypes of LFF systems were designed, built, and tested in a secondary aluminium production. A molten metal flow at high temperature (700°C-850°C) can be effectively measured. The LFF technique method allows measuring precisely the volumetric and mass flow rates linked with Lorentz force, and the mass accumulated within production process.IntroductionThe present work demonstrates the development of a non-contact electromagnetic system for measurement of a liquid metal flow. Our approach embodies the Lorentz force velocimetry [1-6] technique which is physically based on a measurement of the force acting on an external magnet system the field of which interacts with the flow. This force is exactly equal to the braking Lorentz force induced in a flowing conducting fluid. In what follows a measurement system based on the Lorentz force velocimetry principle. For monitoring and controlling the production process it is desirable to measure continuously the mean velocity of the liquid metal in order to deduce the mass-flux and volume-flux from it. The form and dimensions of the magnet system are in agreement with geometry of the operating channel. We consider here a version of magnet systems in a composition of permanent magnets.The LFF possesses a number of advantages which make it attractive for the measurement of flows in hot and aggressive melts. The relation between the measured force and the desired volumetric flow rate is often linear (for closed channel or at a constant liquid metal level in open channel). For the converting of the measured force into volumetric and mass flow rate we should know the calibration factor. The calibration factor is independent of the viscosity and density of the liquid metal and depends only on the magnetic field magnitude, the electrical conductivity of the liquid metal and the geometry of the channel in which the liquid metal flows. In aluminium production, for instance, there exists a number of standard alloy compositions having welldefined conductivities for which the calibration factors can thus be tabulated. We consider below consistently effects in liquid metals arising under influencing magnetic field, construction principle of LFF and measurements of metal flows at industrial conditions."

Jan 1, 2011

By Hideki Yamamoto

A new technology to convert fluoride gas (C2H2F4 : R-134a) contained in the exhaust gases from semiconductor manufacturing plants and refrigerators directly into a harmless substance have been established, thus, presenting a new concept for the disposal of fluoride gases such as CFCs that are associated with the global warming. Experimental results verify that chemical reactions with metal compounds can take place at substantially lower temperatures of 700- 800K as compared with combustion treatment temperatures of 1200-1500K. The reaction product is mainly metal fluoride, which chemically is a harmless material. Furthermore, this process is compact, easily controlled, safe and has low running costs. This paper deals with a new chemical reaction method for the harmless disposal of gases effecting the global warming.

Jan 1, 2003

By George H. Edwards

Most cullets consumed in large-volume glass manufacturing processes receive little processing beyond crushing. But lead-glass cullets for specialty glasses such as industrial lighting refractors or cathode-ray tubes are combined with metals and various coatings that prohibit their direct recycling into the glass-melting processes that created them. In many cases, the contained lead renders these cullets hazardous. At present, virtually all industrial processes to separate one cullet from another depend on hand sorting, and thus are necessarily costly per unit weight. Lead-glass cullets of differing lead content are of interest because they offer the possibility of separating one glass composition from another by high-speed, automated processes at low cost. A potential process for comminution, cleaning, and separation of lead-glass cullets would involve primary and secondary crushing, magnetic and other metals separation, attrition scrubbing in water, separation of glass types by gravity techniques, drying if necessary, sampling, and preparation for transport to the point of use. Process water would be filtered to remove finely divided coating materials and glass, and reused. If carried out on a scale similar to a specialty industrial mineral processing plant, the cost per unit weight of such processing should be substantially less than the raw material value of the cullet in specialty glass production. The added value of avoiding waste disposal costs makes this process economically attractive.

Jan 1, 1994

By Kai Kang, Jun Bao, Shouping Liu, Xiao Sun

Powder characteristics have a significant influence on selective laser melting (SLM) process. In this research, particle size, surface contour and the microstructure of IN718 powder used in SLM were tested, and the physical and chemical changes during heating process of the powder were investigated as well. The shape characteristic and fluid properties of IN718 powder were defined and measured. It is shows that most particles of IN718 powder exhibited nearly spherical shapes, and the particle size is about 22.95μm. On this basis, IN718 sample was fabricated by SLM process using the powder and the microstructure of the fabricated sample was investigated. The results indicated that the sample has a dense microstructure, no macro-defects but a few micropores and porosity. Compared with the powder, there was no new phase formed in the sample and melting point of the sample was little less than that of the powder.

Jan 1, 2015

By Yuzuru Sato

Viscosity has been measured for various molten binary alloys of nickel with iron, cobalt and chromium in order to clarify the behavior of viscous flow of molten nickel alloys. The entire concentration range for iron and cobalt and 0-67at% of chromium content were studied. The measurement method was an oscillating cup viscometry using an alumina crucible that was precisely machined. The temperature was up to about 1880K for all the measurements. The results represented good Arrhenian relationship although some measurements included overcooled temperatures. The isothermal viscosities increased monotonously with an addition of iron and chromium into nickel. The addition of cobalt increased after stationariness. The isothermal viscosities showed concave curves. Activation energies increased monotonously by adding all the elements into nickel. These phenomena were considered to be related to the thermodynamic properties such as the heat of mixing and the structures of mixture melts.

Jan 1, 2003