Search Documents

By J. Hupka

The limited effectiveness of the original hot water process for recovery of bitumen from certain Utah tar sands containing bitumen of higher viscosity (e.g. Sunnyside, Tar Sand Triangle)1,2 indicated that bitumen viscosity strongly' influences the separation efficiency. In this regard, there should exist a critical value of bitumen viscosity above which the effectiveness of the hot water process decreases significantly. Apparently certain tar sands contain bitumen of such high viscosity that even a digestion temperature of nearly 100°C is insufficient to lower the viscosity below the critical value. In addition it seems that differences in physico-chemical forces which act between sand and bitumen are negligible in comparison to the difference in visco-mechanical forces. Predominantly mechanical forces hold viscous bitumen on the rough surface and in the pores of sand particles, resulting in strong adhesion. This phenomenon is a critical feature in the phase disengagment of oil-wetted domestic tar sands with viscosity control by temperature. Besides increasing the temperature for viscosity control the effectiveness of the original hot water process could be enhanced by control of bitumen viscosity with diluent additions. Strictly speaking this appraoch is the only possibility for heavy bitumen for which the high temperature of digestion does not lower the viscosity sufficiently. As a result of viscosity control by diluent addition the digestion temperature can be lowered which is important from an industrial standpoint. Another important consideration is that effective phase disengagement occurs only when the entire bitumen phase has the same viscosity. This means that some time (penetration time) is necessary for complete and uniform dilution of the bitumen. If the viscosity of bitumen, which is a function of temperature, diluent addition and penetration time, controls the separation efficiency, hot water processing of many different kinds of tar sands should be possible, assuming that the sand phase consists primarily of quartz-type minerals.

Jan 1, 1982

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

A ventilation study was conducted at a western U.S. coal mine to evaluate the movement of longwall face air and exchanges between the face and worked-out areas to document the presence or absence of face airflow pathways between these locations. This field study was part of a project investigating the effect of longwall face length and caving characteristics on longwall face air behavior and its potential movement on and off of the face. Tracer gas experiments using sulfur hexafluoride (SF6) were done to describe air movement on the face and in the mined-portion of the active panel. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob.

By Arman Hazrathosseini, Ali Moradi Afrapoli

Fleet management systems (FMSs), as a pivotal part of any surface mining operation, need to evolve from conventional to intelligent systems because of both Mining 4.0 requirements and some shortcomings inherent in conventional methods. However, this novel transformation needs to be investigated technically and strategically. To this end, previously published research works on intelligent FMSs are explored to track the latest status of these third-generation frameworks within the surface mining context. Their underlying models are then compared in terms of five categories of allocation and dispatching features to pinpoint the technical gaps ignored. Having drawn the future lines of research, the present work then leverages the popular SWOT analysis method to outline the strengths, weaknesses, opportunities, and threats associated with the advent of these intelligent FMSs in mines of future. By and large, the analysis indicates that advantages outweigh disadvantages. Solutions are offered to address the existing weaknesses and threats.

Apr 1, 2024

By Michael Wortley

Metso?s Process Technology and Innovation group is a world leader in mineral processing consulting. A significant amount of this consulting work involves process integration and optimization (PIO) studies, which include investigating the effects of drill-and-blast design and implementation on downstream processing. Critical to these studies is the ability to track specific ore into, and through, the plant. To increase the accuracy of this ore tracking, Metso Process Technology and Innovation (PTI) developed a system to track ore using a radio frequency identification (RFID) transponders technology designed to allow tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles and, finally, into the concentrator. The system is called SmartTag. Since its commercialization in 2007, SmartTag has been used in the majority of PTI?s consulting projects, and several permanent systems have been installed worldwide.

Jan 1, 2012

By L. Yuan, D. Bahrami

Underground mine fires remain a concern for mine operators, posing a health and safety risk to mineworkers. In the last decade, the number of mine fires has decreased significantly. However, dealing with an unknown fire in underground mines can be a challenging task, which could lead to a hazardous condition for miners during an evacuation and rescue operation. A timely detection of a mine fire and monitoring its characteristics—namely, size and location—are of great importance in reducing the risk of mine fire injuries. A new, improved fire location algorithm has been developed and integrated into an atmospheric monitoring system (AMS) program by researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH). This paper describes the new fire location model and presents the results of verification fire tests conducted at the Safety Research Coal Mine (SRCM) facility of the Pittsburgh Mining Research Division (PMRD) using the collected AMS data. NIOSH is endeavoring to develop workplace solutions to improve the detection of and reduce the risk of hazardous conditions in mines. The results demonstrate successful application of the improved fire location model and provide a useful tool for solving the problem of unknown fire location and reducing the risk of hazardous conditions.

By Robert Bohman

I truly free enterprise system requires free and unrestricted competition among a diversity of suppliers, in order to function properly. The natural attrition of the marketplace tends on the one hand to narrow the competitive field ... but the flow of new competitors entering the arena provides a "diluting" effect, and a "balanced" market place. Without the ready flow of new business entrants, the market becomes increasingly concentrated in the hands of fewer and. fewer firms. Competition among suppliers is diminished and the "free" marketplace suffers accordingly. A number of organizations, both governmental and private, have recently expressed grave con¬cern over the competitive future of the Western coal market. While most have noted that there is currently adequate competition within the Western market, some have cited the growing con¬centration of coal ownership ... particularly federal lease ownership ... in the hands of a relatively few firms. They suggest that unless this apparent trend is reversed or at least stemmed, the number of new firms entering the federally-dominated West may become reduced to the point where competition will suffer.

Jan 1, 1982

By Roger L. Hulette

Mt. Newman Mining Co. is now completing an expansion program, begun even before initial construction was complete, which will result in facilities with the ability to ship over 30 million tons of iron ore per year by early 1973. Confidence in such rapid future growth was evidenced by careful planning for the future expansion of those facilities provided for initial operation of the project which first shipped ore on 1 April 1969. Ore sales contracts totaling more than 300 million tons have been negotiated, thus justifying the optimism which led the joint venturers to provide over $200 million in initial investment and a like amount in capital required to finance the continuing expansion program. Members of the Mt. Newman Joint Venture are: Amax Iron Ore Corporation - 25% (a subsidiary of American Metals Climax) Pilbara Iron Ltd. - 30% (a subsidiary of Colonial Sugar Refining) Dampier Mining Ltd. - 30% (a subsidiary of Broken Hill Proprietary) Seltrust Iron Ore Ltd. - 5% (a subsidiary of Selection Trust Ltd. of London) ? Mitsui C. Itoh Iron Ore Pty. Ltd. - 10% Mt. Newman Mining Co. Pty. Ltd. manages the project on behalf of the five companies which make up the joint venture.

Jan 1, 1972

By BEN WANG, HAORAN LI, YALI FENG, JINRONG JU

Acidic wastewater is at present directly neutralized with lime or limestone, which wastes resources such as titanium, scandium and iron and generates a great deal of solid waste. This study proposes a novel approach for the separation and recovery of titanium, scandium and iron from acidic wastewater, and utilization of red gypsum. The proposed process not only recovers valuable metals from acidic wastewater but also treats the red gypsum that has previously been dumped.

Aug 1, 2022

By David M. Abbott

This paper is a companion to, and amplification of, the ?History? section of the 2014 version of the SME Guide for Reporting Exploration Results, Mineral Resources, and Mineral Reserves (SME Guide). The need for the careful examination and evaluation of mineral deposits has long been recognized. In the book De Re Metallica, Georgius Agricola noted, ?Moreover, a prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him? (1556, p.29). Agricola further stated, ?Now a miner, before he begins to mine the veins, must consider seven things, namely: the situation, the conditions, the water, the roads, the climate, the right of ownership and the neighbors? (1556, p. 30). The elements of Agricola?s seven things, much expanded, are incorporated into the 2014 SME Guide. As reflected in this quotation, veins were the primary concern of mining until 20th century technology permitted bulk mining techniques. The need for standardization of reserve descriptions arose along with the development of western mining in the United States and the concurrent development of mining engineering and mining geology as professions. By the turn of the century, debate about terminology of various classes of reserves was in full swing. Herbert Hoover noted in 1909 (p. 16-17), ?The old terms ?ore in sight? and ?profit in sight? have been of late years subject to much malediction on the part of engineers because these expressions have been so badly abused by the charlatans of mining in attempts to cover the flights of their imaginations. A large part of Volume I of the Institution of Mining and Metallurgy has been devoted to heaping infamy on these terms, yet not only have they preserved their places in professional nomenclature, but nothing has been found to supersede them. ?Some general term is required in daily practice to cover the available field of visible ore, and if the phrase ?ore in sight? be defined, it will be easier to teach the layman its proper use than to abolish it. In fact, substitutes are becoming as badly abused as the originals ever were. All convincing expressions will be misused by somebody.? Hoover (1909) noted that the common terms at the time were: ? Positive ore or ore developed: Ore exposed on four sides in blocks of a prescribed size. ? Ore blocked out: Ore exposed on three sides within a reasonable distance of each other. ? Probable ore or ore developing: Ore exposed on two sides, ? Possible ore or ore expectant: Ore in whole or in part below or beyond the range of vision. Hoover stated that these, and similar terms, overlapped and had the difficulty of failing to account properly for geologic variation in metal distribution beyond the exposed face. Certainly assuming extension of values along a vein is reasonable, but how far? Also, these definitions are for vein deposits, not all types of deposits are in veins. Hoover (1909, p. 19), therefore, defined the following terms. ? Proved ore: Ore where there is practically no risk in failure of continuity. ? Probable ore: Ore where there is some risk, yet warrantable justification for assumption of continuity. ? Prospective ore: Ore that cannot be included in the above classes, nor definitely known or stated in any terms of tonnage.

Feb 1, 2014

By Samuel Rigert, Marco Bettelini

"INTRODUCTION AND OBJECTIVES Long rail tunnels require in most cases powerful mechanical ventilations. Besides requirements related to normal operation and maintenance, operational safety always requires a high level of smoke management. Identifying the optimum ventilation concept is essential for achieving proper performance and safety while keeping investment and operational cost at a reasonable level. For the purpose of the present paper, long tunnels have a length of typically 20 km or more. This is related to the European classification of trains (TSI 1303/2014), where the maximum distance from the portals to a firefighting point and between firefighting points is limited to 20 km (only category B passenger rolling stock allowed) or 5 km (general case). From TSI 1303/2014 it can be concluded, that tunnels over 20 km require in any case emergency stations with complex mechanical ventilations. Based on the experience arising from a number of recent projects in the European area, including in particular Gotthard (GBT), Lötschberg, Lyon-Tourin (LTF), Brenner (BBT) and Gibraltar, safety-relevant issues related to the ventilation of long railways tunnels are reviewed in this paper. Amberg Engineering is directly involved in these challenging design tasks and can provide first-hand experience and know-how. As a particular highlight, special attention is devoted to the longest tunnel worldwide, the 57 km long Gotthard Base Tunnel, which will be commissioned in 2016. THE GOTTHARD BASE TUNNEL Overview The Gotthard Base Tunnel will be commissioned in 2016 (official inauguration on the 1st of June and beginning of regular operation on the 11th of December) and will be the worldwide longest tunnel. Its complex and powerful ventilation system is very representative for many other long tunnels and is used as reference in this paper. Therefore, a few key characteristics of the Gotthard Base Tunnel and its ventilation system will be described in some detail in this initial chapter. The Gotthard Base Tunnel (GBT) consists of two single-track tunnel tubes with connecting galleries every 312 meters. Two so-called multi-functional stations (MFS), located at roughly 1/3 and 2/3 of the tunnel length, host the key equipment for normal and for emergency operation. At these locations, double crossovers allow trains to switch from one tunnel tube to the other. An emergency station is located in each multifunctional station, allowing trains to stop in case of emergency. The general layout of the GBT is presented in Figure 1."

Jan 1, 2016

By NARAYAN K. BHAGAT, ARVIND K. MISHRA, Aditya Rana, M. M. Singh

The paper presents an innovative directional controlled blasting (DCB) technique for excavating unstable slopes along the Konkan railway in India without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw were developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3, irrespective of the actual free face, was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle was changed from 80–82 to 45–47 degrees, and possible wedge, planar and toppling failures were eliminated. No incident of rockfall and slope failure along these slopes has been observed after the stabilization.

By KAGAN BENZESIK, OMUR CAN ODABAS, SELCUK KAN, Onuralp Yucel

In this study, domestic molybdenum disulfide (MoS2) concentrate was roasted in a chamber furnace and then in a rotary kiln. The behavior of the roasting process was examined in both furnaces, and which type of furnace is more advantageous to use in mass production was investigated. It is theoretically possible to roast in a chamber furnace, but a major problem was observed when the amount of concentrate was increased in the chamber-furnace experiments. The problem was solved by using a rotary kiln. This study improves the understanding of the roasting of  MoS2 concentrate and presents a different perspective to the industry, showing that rotary kilns can also be used for roasting.

By Robert E. Charles

Much has been said about digital computer control of metal and mineral ore dressing processes, but little has been done. This pa- per discusses what practical use can be made today of a digital computer in an ore concentrator and how such application can be made successfully. A hypothetical, but commercially common, grinding and flotation circuit is presented in terms of analog measurements which can and are being made in existing plants and a centralized computer control system which is reasonable in terms of today's technology. Dangers and possible disadvantages of such an approach are discussed as well as estimated benefits. Possible future benefits are presented in terms of improved control technology. Development of new measuring devices is not considered as a criterion for computer benefits. The control systems described have been utilized successfully in existing ore dressing operations. However, the degree of success or failure of analog systems is generally left to the interpretation of management rather than absolute analysis. Many factors affect the economic operation of a mineral recovery circuit such as size of facility, flow sheet design, number of operating personnel, percent of recoverable mineral in the ore body, loss to tails, and haulage rates. In existing mills where little or no instrumentation has been used, it is extremely difficult to prove or disprove the advantage of analog control systems on one mill line versus its sisters due to the lack of standards and the lack of ability to separate final products by ton.

Jan 1, 1969

By J. van Wijk

"Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems (VTS). To investigate flow effects under realistic conditions, especially clogging effects, a 136 m high test facility for flow analysis in vertical transport has been constructed using available mining infrastructure. Tests are run in a closed circuit, using a system of downfall and riser pipelines connected to a compact sediment injection- and separation unit as well as the centrifugal pump. The riser is equipped with pressure sensors, as well as temperature sensors, flow meter, concentration meter and high speed camera to allow comprehensive analyses of the flow regime and behavior of transported material within the flow. Additional mobile measurement devices allow wear and tear analyses of pipe material. This paper focuses on the determining factors of the tests leading to the design as well as the installation and trial of the test facility itself and explains the used components and work principles. INTRODUCTION Since the 1970s several research projects had been conducted investigating in the possibility of deep sea mining. In recent times projects for deep sea mining operations have started again, considering the rising demand on natural resources, especially raw earth elements. Yet projects like the Nautilus project on the deposit Solwara 1 [1], or Japanese projects focusing on the region of Okinawa [2] and Chinese projects [3] planning on depths of “only” about 2,500 up to 3,000 m. Until now no economical deep sea mining project was realized, due to the enormous difficulties of deep sea environments. Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects, considering transportation heights up to 5 km. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems or VTS [4]. Critical parts of the system would be identified and investigated to deliver solutions and higher the technology readiness level to a level were planning of a pilot project can be considered. At first case examples for mining projects of seafloor massive sulfides (SMS, 1,600 m water depth) and manganese nodules (MnN, 5,000 m water depth) had been calculated on basis of economical frame conditions, such as planned production rates to be efficient. As depicted in Figure 1 two major possible systems had been used for comparison, airlift system and pump system, considering multiple pump stations or single pumps. Based on the results and comparisons for the calculated vertical transport systems critical components and flow effects had been identified."

Jan 1, 2018

By Jorge Armstrong, Sean Warren, JOSEF BOURGEOIS

The paper investigates the influence of slope height, slope angle, slope material, and rock size on rockfall runout distance in openpit mines. Using statistical analysis and simulation, the study aims to improve rockfall hazard assessment and catch bench design by identifying key variables affecting rockfall behavior.

Oct 1, 2023

The Global Mining Standards and Guidelines Group (GMSG) is building an international, multi-stakeholder community to advance the availability and use of standards and industry guidelines for the global mining community. Standards and guidelines are key strategic tools for operational excellence, enabling companies to move forward with efficient, innovative operations with reduced risk. Launched in May 2012, the GMSG is the first international center to bring together information, resources and collaborative projects for mining standards and guidelines, in an open, knowledge-sharing forum. The GMSG is supported by five partner organizations providing outreach and helping to guide GMSG activities: the Canadian Institute of Mining, Metallurgy and Petroleum (CIM), the Society for Mining, Metallurgy and Exploration (SME), the Australasian Institute of Mining and Metallurgy (AusIMM), the Southern African Institute of Mining and Metallurgy (SAIMM) and the Surface Mining Association for Research and Technology (SMART). GMSG was formed under the CIM Surface Mining Society, though its mandate extends to include underground mining as well. ?SME is supporting the GMSG as a key international activity to advance the implementation of standards and guidelines in our industry, and to provide a forum for our members to access, and contribute to, projects and information to assist their operations,? said SME Executive Director David Kanagy. ?We see the GMSG as a good example of ways the major mining associations can work together for the benefit of all our members.? The GMSG charter encompasses all standards and guidelines that apply to mining; however, a number of subject areas are now being spearheaded by six working groups, namely: ? Access and usage of data from mobile mining equipment onboard systems. ? Operational safety. ? Situational awareness (namely, a unified equipment operator interface). ? Underground operations. ? Asset management and operations data definitions and KPIs. ? Energy in communition.

Oct 1, 2013

The National Mining Hall of Fame and Museum (NMHFM) in Leadville, CO will induct the class of 2011 on Sept. 10, 2011. Representing the coal, metallurgical/processing, research and development, marble and lead industries, this year?s inductees cover a diverse crosssection of the mining industry. William Francis Diamond, Wayne Hazen, Redfield Proctor and Jeffrey Zelms will join 210 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame at the 24th Annual Induction Banquet and Ceremony. The members of this year?s class were selected for being visionaries, leaders and ambassadors both within their own sectors and across the industry at large. Diamond had an illustrious engineering and managerial career that spanned four decades with Island Creek Coal Co. During that time, he was responsible for the engineering and construction of the deepest coal mines producing in North America at the time.

Jan 1, 2011

The global mining industry will always face significant challenges. Some, though, are bigger than others. What do you consider the major challenges facing the mining industry as a whole and SME in particular? Without a doubt, the major issue in both coal and metal/nonmetal mining industries is the ?graying? of the workforce in all aspects of mining. As the baby boomers continue to age, valuable experience is being lost by industry, government and academia. And there is the potential for SME to lose some of its membership. Now with that said, I should note that, despite the aging of the workforce, SME membership continued to grow by 7.1 percent during 2011.

Jan 1, 2012

By A. H. Srnallbone

Over the past few years the rising production costs, shortage of skilled labor, and increased use of lower grade ore bodies have all added justification for the use of on-stream analysis. A rise in the number of on-stream units indicates that this type of assay is now being accepted as a necessity. On-stream analysis is a much more rapid means of obtaining true assays of a flowing product when compared to wet chemistry or "grab" samples dried, briquetted and assayed by x-ray. In contrast, on-stream analysis uses real time samples assayed every 30 seconds while each stream is assayed every 5 to 15 minutes. It is very important not only to know that a change has occurred in the process, but to know what caused the change and how to correct for the change. For example, in a tailing sample the elements of interest comprise between 1% and 10% of the sample. The remainder is water and gangue. Previously the gangue was not assayed nor were the low atomic number elements used for corrections. In addition to the demand for higher accuracies some concentrators were being penalized for excessive Ca or in some cases 5i in their concentrates. This penalty was being imposed by the smelter in order that they could better cope with pollution problems and prolong the life of their furnaces. But until Ca, 5i, and S are measured on-line, nothing can be done about their control. By accurately measuring these light elements on-line, a complete assay is obtained of the total sample providing improved accuracy for the important products. The justification for complete accuracy assays is now even more obvious because they are possible at very 1ittle increased cost and at no increase in analytical time.

Jan 1, 1977

By William Gleason

"Modern society demands much more from the mining industry than just the raw materials it produces. In addition to providing copper, gold, coal and other minerals that make society function, the industry must conduct its operations in a safe and environmentally sustainable manner. This includes the equipment used and the engines that power the machines.In the United States, Tier 4 diesel engine standards that were set by the U.S. Environmental Protection Agency (EPA) are the strictest emissions requirement for off-highway diesel engines. This requirement regulates the amount of particulate matter (PM) and nitrogen oxides (NOx) that can be emitted from an off-highway diesel engine. In Europe, the Euro V standards are driving technology advancement in the sector.The European Euro V standards are required for new equipment manufactured beginning in January 2019. U.S. Tier 4 standards for heavy-duty off-road engines came into effect with model-year 2014 vehicles and equipment. China 6 standards come into effect in July 2020. India’s Bharat Stage VI standards will take full effect in 2020, and the phase-in of BSVIcompliant clean fuels began in April 2018.Caterpillar, Cummins and MTU are three of the leading manufacturers of engines for the mining sector. Each company is working toward creating efficient engines that can function in the often harsh environments found at openpit and underground mines around the world. In short, society is placing demands that are challenging engine manufacturers to deliver a product that can do more work while consuming less fuel and emitting fewer emissions.Technologies range from selective catalytic reduction (SCR) and diesel particulate filters (DPFs) to other engine strategies and emissions control technologies, which deliver near-zero black carbon and nitrogen oxide emissions, and lower greenhouse gas emissions. Caterpillar’s investmentCaterpillar, the world’s largest producer of mining equipment and mining engines, has been at the forefront of the changing demands placed on the industry and has remained on the cutting edge of engine development over the years, thanks to its investments in the sector.“Caterpillar made the choice to fund major engine and machine development work — even during a deep trough in the mining industry — so that Cat machines would meet Tier 4/EU Stage 5 mandated compliance dates of Jan. 1, 2018 / Jan. 1, 2019, respectively. For Caterpillar, these efforts enabled our mining trucks to provide improved engine component life to help our customers’ total cost of ownership (TCO) and produce a neutral TCO compared to our Tier 2 products,” said Jeff Castleman, new product introduction manager, large mining trucks for Caterpillar."

Aug 1, 2019