Search Documents

By Enver Alan

This Research & Development (R&D) study was conducted in the field of applied blasting engineering in Ethiopia, within the AKH Railway Project, which was built in Girena, within the boundaries of the province of Mersa, in the Basalt Quarry at km 346, Ashangi Formation, occured in Eocene geological time in the aphanitic trachibasalt.

Feb 1, 2020

By Cesar Guerra, Alejandro Rojas, Dr. Jhon Silva, Luis Velasquez

The ANN method is applied to predict the P_80 size in one open pit gold mine in Peru. The ANN was implemented in Matlab programming language, and the results from the ANN are compared with data obtained using photo-fragmentation analysis software.

Feb 1, 2020

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan

In the bench blasting, the realisation of an economic, and safe blasting is only possible with a reliable blasting design on condition that considering all sequential activities such as drillingblasting, excavation-loading, haulage, crushing (especially primer crushing). Here what we mean with a good, and reliable design is that ensures an almost displaced, adequately swelled muckpile with desired fragmentation degree for the loaders effectivity, and succesive usage. Meanwhile it must also has no environmental problems such as ground vibration, air blast, and rock flyings, or at least these matters have to be minimised. Two main parameters which have generally being questioned to achieve a safe and economic design on any rock conditions, are specific charge, and burden. In the condition of determining these elements, the other blasting parameters could be calculated according to them, and the blasting design could be completed. Within the scope of this study, it was aimed to determine the optimal blasting conditions of gypsum which is major rock unit of overburden at Sivas Celestine open pit mine. First of all, the engineering (mass, and material) and digging difficulty classifications of gypsum were done according to the current classification systems by using the results of field and laboratory studies. Then the blasting system which was being used on all rock units, was considered, and the necessary data were obtained. After previewing the site properties, predesigns were done, and applied by adopting Langefors design model. The necessary adjustments were done before, during, and after the shots, and the applications were observed. In order to determine, and record the data from each shots properly, a practical form was developed, and all data were transfered to these forms which give information about the blasting results such as muckpile displacement, and height, average particle size, back break, and rock fly existence, number of boulders etc. The blasting parameters such as burden, hole diameter, hole inclination, the amount and position of primers, bench height, delay sequence, and blasting geometry were considered for the iteration of each shots. During the applications, ANFO, gelatine dynamite, and electric delay detonators were used as explosives.

Jan 1, 2004

By O. Rielo, A. Pascoal, P. Katsabanis

The dynamic parameters of two different granites have been obtained using Hopkinson bar experiments. One series of experiments were conducted using a Hopkinson pressure bar apparatus with an explosive source to provide the compressional wave. This wave would travel along the granite bar and would be reflected at the free end. Strains were obtained along the bar to examine the process. Using relatively long bars of rock, approximately 300mm long and 18mm in diameter, the separation of the compressive and the reflected tensile pulses was possible. If the net tension exceeds the strength of the material, spalling is witnessed. By properly selecting attenuation materials and explosive sources, single spalls were created, making results easier to interpret. Numerical modelling enabled the calculation of the propagation of the stress wave along the bar and its reflection at the free end. Knowing the location of the spalls, critical stress levels for rock failure under tension were obtained. Dynamic tensile strengths were also obtained, at different strain rates, using a Split Hopkinson Bar Apparatus. The results provide a measure of the increase of the dynamic strength at high strain rates, relevant to blasting applications. They are useful for the calibration of blasting models and the characterization of rocks for blast modelling, but also provide answers to the basic question of what is the rock strength for blasting applications.

Jan 1, 2011

By Barbara Rutter, Shonn Kevin McNeil

"This study discusses how a prototype was built to measure the sonic velocity in powdered explosives.The sonic velocity of an explosive is a benchmark to determine if the explosive deflagrates or detonates;however, little work has been done to determine this value for powdered explosives. This paperdiscusses the results of the initial prototyping tests where two known mediums, air and water, were used for validation. The prototype did record the sonic velocity within the known velocity ranges of air and water; however, a few depths did not fall into this range. This prototype could be used for testinggranular materials."

Jan 1, 2017

By G. Adderley, Rob. Farnfield, L. Bermingham

The benefits of using electronic detonators within the drilling and blasting process in both surface and underground mining operations are well established and the use of this technology is widespread in the minerals industry. However, many users of such devices will also have experienced misfires where an electronic detonator has malfunctioned and shows evidence of damage from either transient shock or gas pressure. This is typically exhibited as a detonator shell that has collapsed causing damage to the internal electronic components before the detonator has initiated. Users often describe such detonators as being “shrink-wrapped”. The excavation of a misfire is always a hazardous operation, and it is better to minimize the risk of one happening in the first place. As part of a programme to improve understanding of this phenomenon and to allow a comparison between differing designs of detonators, a simple practical test was developed. This process involves the firing of a booster near electronic detonators in water. This paper describes this test work and draws some tentative conclusions on pressures for onset of damage with detonator shells made from different materials. The investigation has also yielded data showing that for some designs there is little difference between the pressure resulting in complete malfunction and sympathetic detonation

Jan 1, 2024

By Joshua Hoffman, Philip Mulligan, Braden Lusk, Tristan Worsey

Blasters rely upon detonators to achieve the designed timing sequence to move material where it needs to go, minimize vibration, or optimize fragmentation. At times detonator inventory on seldom used delays may be slow moving. This can lead to detonators being used long after they were manufactured. This paper addresses the potential shelf life concern as it relates to timing accuracy of shock tube detonators. A recent study was conducted to study the timing accuracy of non electric shock tube detonator systems. A follow up study was then conducted to determine the degradation of the non electric shock tube systems accuracy with time. The follow up study is presented in this paper. Samples of detonators from the initial study were set aside for approximately one year and then tested. The results from the aged detonators were compared to those of the detonators that were tested in the original study. As an extreme case a third set of shock tube detonators was tested using detonators that were between eight and nine years old. The results from these tests are presented as well. Each system was tested at a short medium and long delay time. Statistical analysis was conducted to determine the effect of time on the detonators accuracy. This paper quantifies the importance of regular inventory cycling to help preserve manufactured timing when using non electric shock tube detonator systems.

Jan 1, 2013

By Enrique Munaretti, Cathy Aimone-Martin, Vitor Rosenhaim, Jair Koppe

Production blasts at one of Copelmi’s coal mine operations will be carried out 100 m (330 ft) from a neighborhood located in the town of Butiá, southern Brazil. Mine management is concerned about the possibility of damages and complaints due to blasting operations at close distances to structures of substandard construction. Blasting in the area is characterized by the use of very low powder factor resulting in confined shots in which movement is restricted to a point of almost undershooting the rock. Over the past year, tests were conducted mainly in the overburden area to determine the best approach to be implemented when blasts move closer to the town. Mine management wants vibration levels to be reduced lower than the damage limits proposed by Brazilian regulations to ensure a safety margin and mitigate perception by the community hoping to reduce the number of complaints.

Jan 1, 2013

By Lon Santis, Bill Evans, John Tatom

Debris data from the Department of Defense Explosives Safety Board’s Project ESKIMORE full-scale explosives event test program are compared to quantity-distance (Q/D) standards and quantitative risk analysis (QRA) methods. The ESKIMORE test program involved quantities of explosives ranging from 1,000 to 60,000 pounds detonated in typically sized structures made of metal and concrete. Debris from these events was extensively surveyed and catalogued. The debris patterns from these events show varying degrees of directionality normal to the walls of the structures. These density patterns are overlaid an existing explosives storage site that is comparable to the test conditions. Analysis of the debris patterns in relation to Q/D standards shows that exposures located beyond the Q/D arc but along the normal to walls of potential explosion sites (PES) may have much higher debris density than exposures at the same distance on the corners of the same PES. Analysis of the debris patterns shows that predicted patterns using the QRA tool IMESAFR v2.0 closely match actual patterns. Additionally, IMESAFR based QRA methods are able to quantify the different risk levels of being exposed along the wall’s normal as compared to being exposed on the structure’s corner. Methods and decision making criteria to mitigate risk based on the directionality of PES debris are presented. Copyright ©

Jan 1, 2015

By Johan Hillman, D. Scott Scovira, Thomas Gustavsson, Alexander Bihlar

Hydrogen Peroxide Emulsion (HPE) explosives are an alternative to conventional commercial explosives. HPE does not contain nitrates or ammonia thus eliminating post-detonation NOx fumes and aqueous nitrate discharge. Production of HPE is less carbon intensive than industry standard ammonium nitrate-based emulsions (ANE) and employment aligns with end users seeking to meet Scope 3 ESG emission targets. Swedish tunneling contractor Implenia Sverige was awarded the Högdalen Depot Expansion Project by the City of Stockholm. Implenia Sverige partnered with Hypex Bio to be the first to pilot the application of a nitrate-free explosive system in a large-scale civil construction tunnel. The purpose of the joint project was to evaluate the operational suitability of replacing conventional nitrate-based bulk explosives with HPE in a large-scale tunnelling project. When the project commenced in September 2023 both standard nitrate-based emulsions and HPE emulsion were used in parallel (Tunnel Right and Tunnel Left) to enable operational, performance, and environmental comparison. Identical drill patterns and initiation techniques were applied to both tunnel headings. Performance data collected included round advance, usage, and perimeter quality. Implenia managed all drilling and charging operations and Hypex Bio provided technical support, including technicians and chemists. HPE is viscous and pumpable using conventional emulsion pumping delivery systems. Variable density functionality enabled loading different charge weights into cut, lifter, production, and perimeter holes. The primary rock type was hard sedimentary gneiss with approximately 150 MPa [21,755 psi] Uniaxial Compressive Strength (UCS). Fracture systems with infilling occurred in both tunnel directions. Rock quality factor was “Good to Very Good” on the RMRb (Rock Mass Rating) scale. Epiroc Boomer rigs were used to drill rounds averaging 4.9 m [16 ft] deep with high accuracy and precise reference positioning.

Jan 26, 2026

By Randy Wheeler

In recent years the issue of seismograph calibration and accuracy has been a major focal point of the ISEE Blast Vibration and Seismograph Section. In fact, questions concerning the consistency and reliability of seismograph measurements essentially led to the development of this ISEE section. One of the early actions of the section involved the development of “Field Practice Guidelines” for the use of seismographs. These guidelines specifically state that “Placement and coupling of the vibration sensor are the two most important factors to ensure accurate ground vibration recordings.” This paper will address the results obtained from using different coupling methods to record vibration and airblast levels generated from production blasting in a limestone quarry. The data obtained clearly indicate that seismometer burial provides the best coupling for recording ground vibrations. Microphone height has also been an issue regarding the accuracy of recorded airblast levels. The data we obtained indicates that microphone height is not a significant factor.

Jan 1, 2004

By Khiva Haidar Shauma Tassno, Zulham Ahmad, Farhan Harist Maharesi, Abdullah Badawi Batubara

Blasting operations can use a bulk emulsion explosive (EE) with a formulation based on used oil as a replacement for refined fuel oil. The most commonly employed used oil for making EE is a mineral based used engine oil that passes an impurity content standard. It is known that not all types of used oil are easily incorporated into EE formulations. Impurities in used oil can disturb EE stability resulting in crystallization and phase separation and consequently led to poor detonation quality. In 2024, a poor blast result occurred at an Indonesian mine due to utilization of used oil that was not within specification. A research project conducted from February to April 2025 found that used transmission oil differs from used engine oil in hydrocarbon composition. Transmission oil contains more additives that affect EE stability due to polarity differences and the disruption of colloidal state stability. Lab tests including stress testing and crystal growth observation aided the development of a stable EE formulation based on used oil and used transmission oil. In mid-April 2025, blast evaluations were conducted using the EE that was formulated using used engine oil and used transmission oil. Measurements of velocity of detonation, fragmentation, and digging time, demonstrated high quality EE was produced. Application of used oil in EE revolutionized the capability of mining operations to improve blast sustainability and cleanliness. Through comprehensive research, robust testing, and effective supply chain management, it is possible to replace some portion of refined fuel oil with used oil without compromising blasting performance. The inclusion of used transmission oil broadens the overall used oil specification and increases the volume of recycled used oil available for blasting. The increased volume of used oil available can reduce the amount of waste generated by mining projects while maintaining operational efficiency.

Jan 26, 2026

By Raúl Carretero de la Hoz, Leonardo Soares Chaves, João Paulo Soares Toneli, Francisco Felipe da Silva Dantas, Marcos Peres Lopes, Marcus Vinicius da Silva Gonçalves

The mining activity results in environmental impact and thus requires the adoption of techniques to minimize its effects. The rock blasting process is required to break up and move the rock enabling the haulage of the material, however, it might also cause undesirable effects such as flyrock, overbreak, excessive ground vibration or air-blast at the neighboring communities and damage to civil or geological structures located nearby. The Serra Sul mine, commonly referred to as S11D project, has obligations to preserve two natural tropical montane lakes and several maximum relevance natural cavities whose legal preservation radius represents constraints to the mine development and operation. Controlling measures are undertaken to ensure preservation of the cavities, especially during rock blasting stage, with limitations of the maximum instantaneous charge (MIC) and ground vibration control. The demand for high productivity and the large areas with hundreds of blastholes to charge are challenging factors to the charge control. This work presents the development and field application of a map for limiting explosive charges in the rock blasting process at the Serra Sul mine, used for the definition of maximum charges according to the blast location, ensuring the preservation and compliance with the defined ground vibration limits for each cavity. The map is applied at the mine for every blast and when there is a charge constraint, the map helps to define the areas with different charging profiles in the field contributing to higher charging productivity.

Jan 21, 2025

By Johan Gjødvad, Catherine Aimone-Martin, Charles Dowding, Mathias Jern

A residential structure adjacent to a quarry in Ohio was instrumented to record structure motions, resulting wall strains and existing crack displacements in response to close-in blasting within 82 m (270 ft). The project is a cooperative effort among international experts representing the European Federation of Explosives Engineers (EFEE) and ISEE supported by more than 21 persons from eight different countries to compliment prior work performed at the Aitik Mine in northern Sweden. The focus of this study is to compare blast-induced vibration measurements relative to regulatory compliance limits as a percentage of allowable velocities among eight different countries for a one-story residential wood-frame structure with a brick-and-mortar exterior and full basement. Participating counties included Austria, France, Germany, Norway, Sweden, Switzerland, the United Kingdom (UK) and the United States (US). Geophones were placed on the foundation and in the ground in accordance with each country’s regulations to record peak velocities as a function of frequency or distance to blasting. This study extends the work performed at the Aitik Mine to include interior corner geophones to calculate global wall strains and micro-m (micro-in) displacement gauges mounted over an existing drywall crack to measure blast-induced dynamic crack responses and climatological influences on daily opening and closing of a crack. Structure responses were documented for 68 blasts conducted north of the structure from February through September 2023 of which 17 blasts were selected for detailed analyses. The highest in-ground PPVs recorded were 43 mm/s and 59 mm/s at the NE and SW corners, respectively. Measurements from these blasts plotted within each country’s limits provided a comparison of stringency among the counties. The percentage of compliance limits among counties ranged from an average of 114% for the US, UK, and Austria limits to the highest of 585% for Switzerland. Despite these high percentages of compliance for all countries, the global tensile strains induced by these blasts were at most only 12 μ-strains and occurred with the highest velocity blast that exceeded each county’s limit. This high percentage of compliance and low strain level demonstrates the restrictive nature of the regulations studied. Peak dynamic crack opening and closing during blasting averaged 20 -m (0.0008 in) while the 12-hour weather-induced crack displacement during the time period over which blasting occurred averaged 200 -m (0.008 in) and the largest 12-hr change in crack width was 356 -m. This low level of crack response validates the observation that the studied regulations have highly conservative limits for cracking potential of standard building materials.

Jan 21, 2025

By M. Ganster

Austria’s biggest supplier of oil and gas, transports gas through the West Austria Gasline for domestic consumption. In addition, the OMV also works as gas carrier and ensures the transit into neighbouring countries.

Jan 1, 2010

By Agung Wibowo

The incident of Ammonium Nitrate explosion in Beirut on August 4, 2020, became a wake-up call to Ammonium Nitrate stakeholders for mining and construction regarding the deadly risks associated with explosives management. This is a very expensive a lesson learned for all parties involved in the storage of explosives.

Feb 1, 2020

By Tristan Worsey, John Rathbun, Andres Malone

A run of mine, low grade gold heap leaching operation is currently looking to increase ounce recovery by decreasing run of mine fragmentation size. Current blasting practices have resulted in an average fragmentation size of 80% passing 7.05 inches (179 mm). It is estimated that a decrease of 2 inches (51 mm) in the 80% passing fragmentation size has the potential to yield up to a 2.5% increase in the overall life of mine recovery within this ore body. This potential recovery increase could lead to an increase in recoverable ounces which, in turn, would lead to a better profit margin. As this particular deposit is composed of predominantly low grade heap leach the capital investment in a crushing facility was cost prohibitive, it was therefore decided to look into the current blasting practices as a means to improve fragmentation.

Jan 1, 2015

Investigating blast vibrations typically utilises scaling and attenuation models for prediction of vibration amplitude over a range of charge weights and distances. A number of generalised relationships have been established from many years of far-field data analysis, where small changes in charge weight and ray-path distance are less critical. Under far-field conditions, small variations in local geology or geometry do not significantly affect the vibration scaling behaviour over an expected range of data. In the near to intermediate-field (less than 5 times the explosive charge length), small variations in wavepath and rock mass conditions between a blast and a monitoring point can greatly affect the outcome of vibration modelling. This case is especially true for underground blasting in sublevel open stoping, where the paths of blast-induced vibrations regularly encounter voids and preconditioned ground.

Jan 1, 2010

By Eduardo Lozano, Vilem Petr

This study demonstrates the ability of high-order, shock-capturing methods to simulate detonation wave propagation in right circular cylinders of non-ideal explosives. 2-D axisymmetric, reactive Euler equations were solved for the detonation of the highly non-ideal explosive ammonium nitrate-fuel oil (ANFO) using a simple pressure-dependent rate law and perfect gas equation of state. The fractional step method was applied to the convection and reaction operators using a 2nd-order Strang splitting. The flow solver consisted of a finite difference scheme where the flux is reconstructed by a modified fifth-order weighted essentially non-oscillatory (WENO5-Z) with local characteristic decomposition and local Lax-Friedrichs (LLF) flux splitting. Time integration was performed by a third order total variation diminishing (TVD) Runge-Kutta time discretization method, also known as the strong stability preserving (SSP) method

Jan 1, 2019

By R L. Keller

Hong Kong has some of the most restrictive practices regarding blasting than any place in the world. Regulations regarding vibration limitations are 1 in/sec for structures and 0.5 in/sec (or even less) for most utilities; with no recognition of frequency response or adjustment. The Hong Kong Geotechnical Engineering Office has one of the most conservative approaches and protective guidelines for pre-blast assessment of slopes subjected to blast vibration (SEE paper '96). The protective measures to control flyrock generally required by the Mines Division are additionally very stringent. It is not uncommon for the costs associated with protective measures or methods which must be employed to exceed the cost of the drilling and blasting itself - or to waiver blasting application unfeasible altogether. From these restrictions it can easily be imagined how blasting in this urban environment would be most challenging.

Jan 1, 1997