Search Documents

By Gungor Tuncer, Ali Kahriman, Umit Ozer, Abdul Karadogan, Mehmet Aksoy, Ertugrul Kaya, Deniz Adiguzel

This research was performed on the quarry that will be opened to produce aggregates and rock filling material at Catalagzi region at Zonguldak providence. Excavations will be done by drilling and blasting. However, there are some structures which can be adversely affected by blasting at the quarry. These structures are a methane exploration drill hole and a house at the distances of 340 m and 390 m, respectively. The one of the main goals of this study is to perform a preliminary assessment of possible damage effect of ground vibrations induced by blasting on these structures by risk analysis based on ground vibration measurements.

Jan 1, 2009

By Raimo Vuolio

"Over the past 30 years, the Nordic countries have developed similar practices for estimating damage caused by rock blasting vibrations. However, over the last few years the risk of damage has sometimes been estimated by using international values, which have created unnecessary costs, since they are too conservative. This paper gives a proposal for Finnish blast vibration standards and a calculation model for the extent of the zones for building inspection, risk analysis, and vibration measurements. The international conclusion is that particle velocity is the best descriptor for limiting damage potential for structures. Over 900 000 vibration data recordings from 52971 blasts were collected for this paper during 1970-1989. They show that the most practical description is the vertical component of the peak particle velocity. As rock is a nonhomogeneous medium, it is hard to predict the need and scope of risk analyses, building inspection, and vibration measurements. As a large number of blasts were monitored for the recording of the peak particle velocity in several locations in Finland, and the data combined, it is possible to establish safe scaled distances for the calculation of the need and scope of risk analyses, building inspections, and vibration measurements."

Jan 1, 1991

By Ken Tunnel

In the spring of 2005, the Lake Superior Chapter of the ISEE invited me to speak about raw materials used for blasting, anhydrous ammonia and the effect of this important feedstock on the cost of ammonium nitrate.The invitation was extended because our company is involved in trading ammonia and the production of ammonium nitrate. In a response to a request to update that presentation, it struck me how events such as hurricanes Katrina and Rita can change the landscape of our businesses.

Jan 1, 2007

By John N. Jr Edl

Geokinetics, Inc. has pioneered an in-situ oil shale retorting production process that provides the requisite void space for producing a permeable rubble bed, within the retort zone, by using the explosive energy from vertical blastholes to lift the overburden. By installing suitable instrumentation on the surface of the overburden over an appropriate blasting pattern, it is possible to obtain estimates of the average radius of gas penetration around the blasthole and the average volume, per unit length of blasthole, that is actually occupied by the explosively produced gases (which includes both the volume of the cracks that are penetrated by the gas pressure and the deformed blasthole volume). It is expected that these estimates can be used to examine, and quantify, the effects of such blast design parameters as the type of explosive, the blasthole diameter, the geometry of the explosive charge (length to diameter ratio), and the relative timing of sets of charges.

Jan 1, 1983

By Geraldine Rosenthal, Gadi Yohan, Roman Benram

Description of Project: Tamar Group’s civil division was awarded a contract to implode the Sun Hotel, an abandoned 14-story building located along Bat Yam’s coastline, roughly two kilometers south of Tel Aviv, Israel. On Nov. 6, 2012, Tamar Group’s experts positioned explosives in strategic locations of the building, targeting its central pillars, which then caused the building to collapse within seconds. Tamar Group used a relatively small amount of explosives in order to generate a well-controlled blast. This is the largest scale demolition carried out in Israel to date.

Jan 1, 2014

By Lex L. Udy

External detonation generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating explosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall.

Jan 1, 1977

By R E. Langston, S M. Gazioglu

A preconstruction inventory program was conducted to determine the existing conditions of residential, non-residential and all other structures within 2,000 feet of the blasting limits for a highway excavation site in Asheville, North Carolina. Prior to major production blasting, eleven test blasts were detonated to establish site specific propagation parameters in order to develop contours of maximum allowable explosive charge weights per delay. The method of scaling distance by the square root of charge weight per delay was utilized in developing the contours of allowable charge weights. The charge weight contours were revised during blasting operations as additional vibration data became available. The effects of blast induced vibrations on a nearby water storage reservoir, a nearby vehicular tunnel and other adjacent residential and non-residential structures were observed and monitored over a period of two years of blasting operations.

Jan 1, 1980

Previous approaches to pre-split blasting theory have tended to concentrate on the mathematics of dynamic stress wave interaction, whilst only recognizing some interaction with quasi-static stresses induced by expanding gases in the boreholes. However the decoupling used in pre-splitting is specifically designed to reduce dynamic effects to a level that a small degree of radial fracturing is created around the borehole which is emphasized and extended by quasi-static gas effects. It can thus be argued that the process has more in common with hydrofracture than with more conventional use of explosives.

Jan 1, 1984

By Chuck Kliche, Bill Clements

This project involved the removal of the top of an old water supply reservoir tank for the City of Lead, SD by explosives. The general contract called for the removal of the concrete top without damaging the sides or floor of the reservoir. The option of a rock hammer was eliminated, due to the possibility of an unpredictable collapse damaging the sides or floor of the reservoir. Different blasting options were discussed between the primary contractor and the blasting contractor, along with the pros and cons of each. The primary contractor settled on the option of drilling the structure for blasting versus using shaped charges

Jan 1, 2007

By Dale Preece, Stephen Chung, D. Scott Scovira

The DMC_BLAST (Distinct Motion Code) has been developed to model rock motion and displacement during the gas expansion phase after the detonation of an explosive in a borehole. Recently, a designated delay firing order algorithm was written into the DMC_BLAST code. The model can now be used to analyze rock mass displacement for a V-cut, center opening, or sinking cut initiation sequences. This new feature allows the investigation of the effects of delay firing order on rock displacement when blasting complex inter-bedded and ore-waste structures. The model provides important ground movement and mixing indicators for dilution control in surface gold mining relative to the initiation sequences employed. Echelon blasts as compared to center opening type blasts show differences in their internal muckpile displacement. These displacement differences can be important to operations that mine narrow strike driven ore bodies. The model also has applications to through coal seam blasting and demonstrates that down-dip blasting is a better alternative than up-dip blasting. There is less disturbance to the dipping coal seam and less mixing of the rock and the coal.

Jan 1, 2000

By Michael Wieland

Sharp transient stress waves generated during the delay blasting of underground coal can damage unfired borehole charges remaining in the delay pattern. These tremendous stress pulses in coal bear a strong resemblance to underwater shock waves, despite differences in rise times, damping rates, and scaling relations. "Shock wave" terminology is adopted to distinguish the sharp transient waveforms propagating through the coal from the gas-driven stresses that rift the coal. Reported waveform characteristics of shock waves through underground coal were utilized to design a simulator test for rating the impact resistance of cap-sensitive explosives. Theoretical minimum borehole separations were determined for each cap-sensitive explosive from the requirement that worst-case waves hitting an unfired charge would not exceed its impact resistance rating. Rugged explosives have higher impact resistance and will function properly at smaller borehole separations. Additional work is required to verify the findings from the simulator technique and modeling relations reported here.

Jan 1, 1990

By Robert A. Cummings, Francis S. Kendorski, Charles H. Dowding

During the summer of 1980, a field project was carried out to determine the stability of the beautiful and dramatic natural limestone pinnacles (locally termed "Hoodoos") at Bryce Canyon National Park, Utah, when subjected to ground motions and airblasts resulting from proposed strip coal mine blasting. The concern arose from environmental considerations associated with the proposed development of a large coal strip mine which would approach within 4 miles of the park. The pinnacles range up to 150 ft in height and are quite slender, producing a fragile appearance. The remoteness and ruggedness of the area required a field camp, and 4-wheel drive vehicles, helicopters, and snowcats for support. Portable magazines were necessary to store the more than 7 tons of blasting agents and explosives required. In conducting the blasting, great attention was paid to environmental impacts. In the field, a target pinnacle was selected and instrumented with mechanical strain gages, and research seismographs that required helicopter placement.

Jan 1, 1982

By Rafael Tadeu Pinto e Moura, Giorgio De Tomi, Jacopo Seccatore

This paper describes a research and development project in an open-cast mine with the goal to achieve an average P80 of 300 mm (11,8”) in the run-of-mine (ROM) product without altering the existing budget. The project included several variables in the blast design that were not previously taken into account, such as the orientation of natural joint sets in the rock mass, specific energy of the explosive and firing sequence. The new blast design method considered the directions of natural joint sets and determined the drilling pattern and the firing sequence accordingly to favor the movement of the blasted rock along its preferential direction, to reduce its confinement. At the end of the project, it was achieved an average P80 of 304 mm (12”) in the ROM, 50% lower than the one at the beginning of the project. The final blast of the project showed a reduction of 3% of the drill and blast cost, employing the same powder factor and the same drill pattern size used at the beginning of the project. The results achieved show how rock fragmentation is related to variables that are not contemplated in the most common fragmentation models: the firing sequence and the direction of movement in the blast.

Jan 1, 2015

By Travis Davidsavor, Stanley: Dong Vitton

Concrete is a common construction material used throughout the world, and with increasing demand of fast-track construction, blasting and concrete casting are occurring simultaneously at many sites where rock is being excavated for concrete placement. However, there has been significant disagreement in the construction industry as to what intensity of shock vibrations green, or fresh concrete can tolerate. Peak particle velocities are often arbitrarily chosen, or are simply based on materials such as plaster and drywall that have been more thoroughly studied in relation to damage. Previous research on green concrete has used the concrete’s static strength subjected to shockwaves at different ages as the primary damage criteria. In addition, the static strength tests have been based on curing time. However, changes in temperature or humidity can dramatically alter the hydration rate, which affects strength development of different cements. To account for temperature changes and humidity the concept of concrete maturity is commonly used and allows the researcher to see where the concrete was in terms of hydration progress. In general, static testing determines the failure stress that the concrete’s macrostructure can handle, and often failure occurs in the natural materials first or along large defects in casting techniques. Dynamic testing or high strain rate testing, on the other hand, loads materials at such a high rate that larger defects do not have time to react and instead the microstructure is more highly stressed leading to higher strength and stiffness values. This is known as the material’s strain rate sensitivity. Since dynamic testing better tests the microstructural strength, it is believed that it may provide a better way to assess damage to green concrete. Testing includes both static and dynamic compression as well as static and dynamic splitting tensile strength to assess whether damaged has occurred to the concrete. No significant statistical evidence was discovered that damage to the concrete occurred at five different “green” maturities from peak resultant velocities ranging from 10.66 in/s (271mm/s) to 4.40 in/s (112 mm/s) with average intensity of 6.7 in/s (170mm/s).

Jan 1, 2003

By Larry Schneider

In 1998, the Blast Vibration and Seismograph Section of the International Society of Explosives Engineers formed a working group to collect and compile a list of regulations limiting ground vibrations from blasting. The goal was to locate those countries, states, provinces, and cities that have such regulations, identify which governmental body enforces them, and determine what limits on ground vibrations are imposed upon the blasting operations. In the course of this study, data was collected from over 60 jurisdictions where peak particle velocity restrictions range from non-existent to very stringent. Some of the regulations were found to be based upon standards grounded in good science, while others possess little or no technical justification. This presentation will summarize the findings of the subcommittee, focusing primarily on what the limits are, which type of blasting operations must adhere to them, and to what structures they apply. The degree to which these regulations are based upon valid scientific and engineering research will be discussed. A listing of specific locations having such regulations and information about those regulations will be provide

Jan 1, 2000

By Adrian Moore, Alan Richards

A real-time system for prediction of the effect of meteorological conditions on airblast overpressure levels has been established in the Hunter Valley Coalfield in Australia. Real-time meteorological data from continuously operating sounding equipment and a predictive meteorological model is input to an atmospheric refraction model that enables the effect of meteorology on airblast overpressure levels in the area surrounding the blast site to be evaluated. Graphical outputs from the model, which are superimposed over a scaled airphoto of the mine and surrounding area, show the extent that airblast levels will be increased. When combined with inputs that quantify the effect of blasting specifications, the airblast levels that will result in the surrounding area from the combined effect of blasting specifications is determined. The model permits those responsible for blasting to make more accurate decisions on suitable times that blasting may take place to conform with applicable airblast limits.

Jan 1, 2009

By Jan Mehren, Arild Neby

Underwater Tunnel Piercing or Lake Tap, often also called the Norwegian Method, will in many projects be an important part of the hydro electric development scheme. The very last blasting round in the Lake Dorothy Lake Tap Tunnel, which penetrated into the lake at a depth of 120 ft (36 m), was such a key step in constructing the Lake Dorothy Hydroelectric Project. A lake tap project is multidisciplinary. Besides the pure blasting and construction technique aspect, engineering geological and geometric considerations that aim to optimize the tunnel alignment making a lake tap possible at minimized risk are of significant importance. Output data from numerical model analysis of the hydrodynamics resulting from the blasting is vital for the final adjustments to the geometrical layout. The planning of monitoring systems for the surveillance of hydrodynamic impact on valves and pipes as well as control with water levels and air pressures prior to and during the blasting, are all additional crucial elements in the design. More than 600 lake taps have been successfully performed in Norway since the 1890`s. The technique, which deserves to be called well proven, has been applied mostly in the hydropower sector but over the last 20 years also for shore approaches in the oil and gas industry. The demand for this technique seems to be ever more growing.

Jan 1, 2009

By Robert Jacob Cefalo, Rio Tinto Kennecott

At the end of 2016, the Mine started a new ore phase in the section of the pit located on the East Wall. The East Wall geological structures required controlled blasting for peak particle velocity (PPV) frequency vibrations to protect the wall. Frequency controlled blasting using linear seed wave superposition modeling was required and implemented to reduce the far-field affects to the wall. This paper covers the work done by the drill and blast engineering group, controls used to protect the mine infrastructure, and the continuation of work-to-date of frequency controlled blasting for wall stability. The narrow width of the layback required the combination of hole sizes to blast large diameter production patterns with smaller diameter trim patterns in the same blast. A single blast had to use different burden & spacing and hole diameters and required the use of different timings throughout the pattern. Electronic detonators were required to limit blast vibrations and accommodate the specific timings needed to reduce low frequencies. The geotechnical group with the help of geotechnical radars worked with the drill and blast group on creating a tracking and reporting of blast performance. The radar readings informed the drill and blast engineers of the performance of the blast as it related to the long term performance of the highwall

Jan 1, 2019

By Jeff Gore, Jack Dermody, David Gribble, Brett Macaulay, Bart Sharpe, Paul Klaric, Paul Thornley, Ben DeVries

Optimal Fragmentation in Block Caving is difficult to achieve as it is generally defined by the rock mass itself and the way in which the cave is initiated. The lower portion of the cave has even less chance as the material has little time for self comminution. Blast Preconditioning of the Block Cave is designed to engineer the lower section of the rock mass to produce material of a suitable size to assist in the initial cave propagation and improve initial drawbell productivity. At Cadia East a plan was developed to drill 150-metre long, vertical up-holes from the undercut level and blast them fully confined to produce fractures in the rock mass. The blast itself was a simple undertaking. However, in the year preceding the first production blast, all aspects of the process were designed, tested and refined across multiple trials. As this type of challenging application had not previously been encountered in Australia there were many unique situations to address. Products and systems had to be developed and adapted to overcome these challenges. These included: Formulating and manufacturing an explosive that is robust and of a high VoD; designing and manufacturing easy to use electronic initiation systems; and, designing pumping systems to combat high head pressures to allow for successful and safe loading of the holes. Close collaboration with the customer ensured that the trials culminated in successfully blasting a hole containing almost 3.3t of explosive. These trials have since led to the blasting of four holes instantaneously, which contain almost 13t of explosive. This paper describes the various components of the system, the challenges and the final result.

Jan 1, 2013

Blastserve, ISEE’s Listserve is being replaced by our new Blasters Forum-online, an exclusive member benefit. Our goal is to provide an ISEE forum for you to network with your peers and exchange technical information and get answers to your technical questions. This forum is unique in the fact that only ISEE members are permitted to review or post on the site. Over time you will be able review the discussion history and use the archived discussion as a valuable resource for trends in the industry. The following are a sample of the discussions that too place recently on Blastserve

Jan 1, 2013