Search Documents

By D. J. Wall, T. D. Johnson, M. T. Parry, G. R. Heath

In coal-fired power stations coal is ground to a fine powder and then transported pneumatically at 25-30 m/s velocity to remote burners. Wear of the conveying pipework is a well recognised problem and traditional lining materials are Nihard and basalt. In many cases these are being replaced by alumina tiles in order to improve life and reduce the frequency of replacement. A programme of laboratory testing of candidate aluminas with AIO, contents between 85% and 99-5% has been undertaken and the results compared with field experience. This gives confidence in the erosion tests, which were designed to replicate most of the field conditions. However, it has not proved possible to draw correlations between the laboratory erosion rates and any of the materials’ bulk properties. SEM, TEM and microanalysis studies have therefore been made in order to look for microstructural aspects that could be influencing erosion rates and it has been shown that intercrystalline cohesion, the matrix phase and porosity appear to have most influence on wear performance. It is necessary to quantify these microstructural parameters if reliable erosion performance is to be obtained. This paper was read at the Institute of Ceramics Annual Convention at the University of Durham, April 1988.

Jun 12, 1905

By D. J. Esdale, D. F. Pridmore, F. W. Lindman, J. H. Coggon

Almost all the presently viable nickel reserves in the Yilgarn Block contain nickel in a sulphide phase. Both volcanic peridotite- associated (VPA) deposits and intrusive dunite-associated (IDA) deposits are characterized by massive, matrix and disseminated sulphides (typically, pyrrhotite, pentlandite, pyrite, chalcopyrite, magnetite and other spinels), though in the IDA deposits the volume of disseminated sulphides is far greater than that in the VPA deposits. Potentially all geophysical techniques have application in the direct detection of these deposits'gravity for the detection of the dense massive and matrix ore; magnetics for the detection of magnetite and pyrrhotite in the ores; electromagnetics for the detection of the massive and matrix ore; and induced polarization for the detection of disseminated and to some extent matrix and massive ore. In practice the application of geophysical techniques is limited to a varying extent by (1) the relatively small size of an economic accumulation of sulphides, particularly the VPA deposits, (2) the extreme depth of weathering and lack of outcrop on the Yilgarn Block and (3) the abundance of geological noise or anomalous responses caused by sources other than economic mineralization.

Jan 1, 1984

By J. M. Smith

This resume provides an account of the work of the Bureau and it's establishment by an Act of Parliament in August 1916. The Medical Bureau is concerned solely with the administration of the medical provisions of the Act. Its main functions are to conduct and to direct or control the medical examinations provided for in the Act. The paper covers the changes in type of silicosis, classification into the three legal stages of silicosis, cancer of the lung and tuberculosis.

Jan 1, 1947

Summary of the morning's events with a Written Contribution to Paper No. 4 and author responses

Jan 1, 1947

By E. H. W. Hornbrook, P. W. B. Friske

Paper presented at the 28th International Geological Congress, Washington DC, July 1989 (International geochemical mapping sessions). The objective of the programme is to establish and maintain a nationally consistent geochemical drainage database. Towards this end systematic surveys have been conducted since 1973. To date more than 200 surveys have been completed to the required standards, representing 180 000 sites and covering about 2 100 000 km2 throughout Canada

Jun 13, 1905

By T Atkinson, A Cobb, R AJIington

Risk management is concerned with the whole spectrum of financial, geological, engineering, legal, governmental, social and occasionally ethnic issues, concerned with mining projects. The inherent risks in mining operations are well publicised, but new issues and hazards arrive on the scene and lake precedence, but the older risks still remain, while insurance cover may not he ‘full cover’ in the future. It has long been recognised that quantitative approaches to risk analysis can play a major role, but although these methods are capable of considerable theoretical precision, the lack of sound risk input data and experienced personnel limits the usefulness of theoretical analysis. It can, however, greatly assist in comparing cases, in identifying areas of risk and help in the investment decision process. Its major contribution to a mining project is that it imposes an investigative discipline that also assists in improving the quantitative approach to risk analysis and hence risk management. Risk analysis and risk management also requires sound common sense and major inputs from experienced geologists, mining, mechanical, electrical and mineral processing engineers. The Engineering Council, in 1992, issued a ten point code of professional practice entitled ‘Engineers and Risk Issues’ (The Engineering Council. 1992), covering our professional responsibilities, the law, our conduct, the need for a systematic approach to risk issues, the use of professional judgement, communications, risk management, evaluation of risk, our professional development in this field and the encouragement of public awareness of risk issues. This is a specific area of training perhaps long neglected by our industry and academic institutions (Atkinson. 1983).

Jan 5, 1996

By R. G. Jones

Chris Hinde talks us through his career from BSc in Mining Engineering to roles with Golder Associates, Schroder Securities, Mining Journal and SNL. He discusses the issues facing the mining industry.

May 1, 2015

By P. Danson, D. A. White, S. Bashir

Composite ion exchange materials made of SnO2, TiO2 and MnO2 can be used to remove radioactive contaminants from nuclear waste streams. In several cases their selectivity and capacity are enhanced by mixing hydrous silica into the matrix. MnO2-SiO2 materials are especially useful for a number of reasons, such as their selection of heavy elements over caesium. Distribution constants and determinations of exchange capacities show that in many instances the properties of the composites are better than those of the oxides alone, while the presence of a chelating agent has been found to reduce the uptake of nuclides considerably. Methods are being developed for the bulk manufacture of the materials. Further work on sorption mechanisms is required to explain anomalous results, particularly the variation in exchange capacity for different elements and the ability of the oxides to sorb colloidal material in alkaline solution.

Jan 8, 1992

By R. G. Siddall, W. Gale

In the UK the development of the science of strata control has been strengthened by a resurgence of interest in the specialism of roofbolting and its associated techniques. The evolution of the theories and practices of strata bolting in roadway stabilisation is discussed. Practical experiences are considered, principally the use of Australian techniques, the relationship between bond strength and annulus and the effects of stress in the ground. Areas of new technology such as cable bolting, injection anchors and on-board bolters are also discussed. The recent advances in computer technology and rock testing equipment and methods have provided the opportunity to simulate ground behaviour under various conditions. Computer modelling developments and the use of techniques to predict ground behaviour are described.

Jan 4, 1992

By J A. Hacked

This paper explores the potential to exploit controls over the outputs of the primary blasting operation, arising from the performance consistency benefits gained in using modern bulk emulsion explosives technology. The former, allied with the latest powerful blast predictive software and measuring tools, offers the user the opportunity to apply control over both cost and performance, which has not been possible in the past.

Jan 12, 1997

By G. I. D. Roach

The leaching, with hydrochloric, sulphuric and perchloric acids, of suspensions and massive specimens of different haematite and goethite samples has been studied. Both accelerating and constant types of leaching curves have been observed. It is concluded that the grain to particle size ratio of the oxide being leached determines which type of leaching curve is obtained, particles containing a large number of individual grains producing the accelerating type of curve

Dec 1, 1971

By A. B. Holland-Batt

Deposition velocities play an important role in many fields of engineering and an impressive range of measured data has accumulated in the literature. Numerous workers have addressed the problems that are associated with the prediction of deposition velocity because of its particular relevance to the design of pipelines and pumping stations. However, despite this extensive effort, the calculation of friction heads still requires reference to experimentally based graphs to determine Durand factors and there is still scope for improvement in the prediction of the deposition velocity at different solids concentrations. Equations to characterise the relationship between the Durand factor and the volume concentrations of solids in the slurry are presented. A correlation for the prediction of the deposition velocity is also developed and tested against some of the classical experimental data. The application of predicted values of deposition velocity in assessing the potential for the sanding-up of spiral separators is then described and a case study is presented.

Jan 12, 1992

By Gibson J.

The writer hopes to prove that the economical tram is of even greater importance than, say, the economical engine, and as no difficult and involved calculations are required, and all the governing facts are simple and well known, the former is more easily attainable than the latter. In the first section of this paper the factors that determine the size and the construction of the tram are examined; whilst in the second section the road on which it runs is dealt with

Dec 1, 1916

By H. B. Bell, L. C. Smith

Measurements have been made of the activity of 'FeO' in 'Fe0'-Mn0-Ti02 melts at 1475 degrees C. The results obtained are discussed in terms of ideal mixing of titanates and in terms of a regular solution model. On the basis of the regular solution model activities of Ti02 and MnO in the Fe0-Mn0-Ti02 and Mn0-Ti02 systems have been derived. The data have been shown to be consistent with the liquidus lines in the phase systems. Examples are given of the application of the data to slag-metal equilibria, being used to derive slag-metal data between liquid iron and Fe0-Mn0-Ti02 slags

Dec 1, 1971

By T. J. White, R. A. Farnfield

Early computerised blast monitoring equipment consisted of a digital version of the existing analogue machines with, perhaps, a few enhancements. Many additional facilities have since been developed to enable the efficient collection of high quality data. These developments are examined with reference to digital sampling, triggering systems, the storage of complete recordings and signal processing. Recent advances have been made in the use of blast monitoring systems that comprise multiple blast monitoring locations with centralised control and data collection. Software has been developed to help record blast parameters and assess environmental effects. Computer databases have many advantages over their paper counterparts. Data can be easily retrieved and processed. The scaled distances used in the prediction and control of peak particle velocities can be calculated rapidly when the data are obtained directly from a database. Since the whole vibration signal can now be recorded, signal processing can be used to provide information such as signal length, dominant frequency and response spectra.

Jan 4, 1993

By T R. Marrero, J W. Wilson

This paper presents costs for a coal log pipeline that can transport coal over distances from 50 km to 1500 km. The coal log pipeline (CLP) concept is a new technology in w hich coal is compacted into water impermeable circular cylinders that can be suspended in water flowing through an underground pipe. CLP includes processes to prepare the run-of-mine coal for compaction, the injection of coal logs into a pressurised water-lilled pipeline, the conveyance of the coal through a pipe including special pumping stations, and the treatment of the coal logs and water at the pipeline outlet. An 8 inch (203 mm) pipeline can transport more than 2 Ml of coal per year. CLP components have been extensively tested in bench-scale facilities where these tests have included start up/shutdown steady state flow behaviour, end of pipeline treatment of water and coal log handling, water hammer effects, abrasion of logs and pipeline, coal log manufacture, and other engineering operations. Several sites are being considered in the United States (US) for the first commercial demonstration that will probably take place in 1998. The cost calculations are based on realistic values for all the components of a CLP. including a return on investment. For pipelines of different diameter, values for coal transportation are presented in terms of $(USVtonne as a function of distance.

Jan 10, 1996

By P. Rama Krishna, B. Narasimha Rao, P. Ali i Peera

Induced polarisation (IP) surveys are commonly used in uranium exploration programmes in India. The IP method is effective in detecting the disseminated metallic sulphides that are often associated with uranium minerals. However, conductive and polarisable host rock or overburden often introduces inductive or electromagnetic (EM) coupling into time domain IP measurements. This makes it difficult to distinguish between responses due to such coupling and those that might indicate economic mineralisation. Attempts must be made to remove the EM effects before the IP technique is used in drilling programmes. Transient decay curves which were recorded during field surveys at Pisnari were factorised using the Marquardt algorithm. Dispersion plots of the amplitudes and relaxation times of the composite exponential function enable a clear distinction to be made between the effects of EM coupling and those of mineralisation.

Jan 4, 1993

By R. W. Ruddle

"Besides copper, iron, silicon, and oxygen, a large number of elements may be present in copper ores, the more important of which are zinc, lead, arsenic, antimony, bismuth, selenium, tellurium, nickel, cobalt and the precious metals; impurities of less importance are calcium, magnesium, aluminium, barium, sodium, potassium, manganese, lithium, fluorine, titanium, uranium, vanadium, tin and molybdenum. All of these elements are eliminated to some degree in the subsequent roasting, smelting and converting operations.Information on the elimination of impurities during the smelting of copper is surprisingly meagre, however, rather more information is available on impurity removal during the smelting of the ore in reverberatory or blast furnaces."

Jan 1, 1953

By E. A. Brocchi, D. H. Gameiro, P. K. Jena

Carbon tetrachloride was found to be a very efficient chlorinating agent for anatase concentrate, even at the low temperatures that were investigated (250-400 degrees C). For example, at 400 degrees C about 90% of the anatase concentrate was found to have been chlorinated within 60 minutes

Jun 13, 1905

By G. Mellgren, O. Mellgren

The conductivity of a solution is often used industrially to control the salt concentrations of reacting systems, normally using electrodes made of glass fitted with platinised platinum electrodes. When a standard platinum conductivity electrode was used to control the acid fed to the leaching circuit for an ilmenite flotation concentrate at Titania, Norway, a deposit of calcium sulphate (containing some calcium phosphate) covered both the platinum electrode and the external glass fitting, rendering the electrode inefficient in the course of a few minutes. A new electrode consisting of a casing, two measuring tubes and an electrode stem is described and illustrated. A significant advantage of its design is that the useful range of conductivity measurement can be adjusted by adjusting the concentration of the electrolyte in the electrode. It has been in use at Titania for about four years with an electrolyte consisting of 0-1 n HCI. It is robust and demands little maintenance.

Dec 1, 1971