Search Documents

By Ruiyang Zhang, Ping Fang, Dezhou Wei, Shuling Gao

A CFD based numerical simulation of flow characteristics of hydrocyclone was conducted with different structural and operational parameters to investigate its distribution characteristics and influencing mechanism. The results show there exist several unsymmetrical envelopes of equal vertical velocities among both upward inner flows and downward outer flows in the hydrocyclone, and cone angle and apex diameter have remarkable influence on the vertical location of the cone bottom of the envelop of zero vertical velocity. It is also found that some tangential velocity isolines exist in the horizontal planes located in the effective separation region of hydrocyclone, and feed pressure has almost no effect on the distribution characteristics of both vertical velocity and tangential velocity of flow in hydrocyclone, however the magnitude and gradient of tangential velocity are made increased obviously, so as to make the high density particles motion velocity to the wall increased and to make the cyclonic separation effect improved. The simulation results also show when the apex diameter increased, the pressure of the fluid field decreased, however the pressure grads in the apex district increased, and the degree of changing is different as the cone angle, which showed some interactive influence of cone angle and apex diameter on the fluid field of hydrocyclone. While the feed pressure also has almost no effect on the pressure distribution characteristics, however the its magnitude and gradient are made increased accordingly, which can improve the separation accuracy according to particle density.

Jan 1, 2014

By L. Weitkämper

The big challenge at present and in the future is the economization of resources. This is applied for the whole industry but particularly in fields of mineral processing. The most important resources are energy and water. The shortage and price advance of energy is worldwide noticeable whereas the shortage of water is regionally limited at present. However due to the increasing world population, associated with a rising standard of living, water will become more and more important. Studies of the Unesco from 2001 indicate that the total water consumption raised seven times since the last 100 years at a growth of population of just three times. (UNESCO-Currier, 10/2001). This trend is going to be increased. While today more than 90 % of the humanity has access to clean water, in 2050 just about 50 % will be in the same situation. These figures indicate the importance of a gentle handling with the resource water. Further more the disposal of fine products, containing most of the water, is an environmental concern and in the future the mining and processing of raw materials will become important and necessary in desert, arid or permafrost areas. In these areas just efficient dry cleaning technologies will allow an economical beneficiation or better enable the processing at all. Most of the separation technologies with high throughput rates in mineral processing are based on wet processes. This applies especially for the separation of fines. Though there are some dry technologies available for the separation of coarse materials, like pneumatic gravity separation [air jigs and air tables], magnetic separation and not least sensor based sorters. Dry separation of fines is bounded mostly on cost intensive and low throughput technologies. The pneumatic separation undergoes at present a renaissance, mainly due to the development of the all air jig by the German supplier Allmineral. This newly developed sorting device yields good results in the separation of coarse to medium size material. All these facts and figures show the potential and motivation for developing an efficient dry separation device for fines. The following article delineates the development, performance and chance of a new dry separation technology for fines.

Jan 1, 2014

By K. C. Corin, M. S. Manono, J. G. Wiese

"It has been suggested that hydroxo species, particularly those of calcium, selectively adsorb onto gangue minerals. Such species enhance the depressive action of carboxymethyl cellulose (CMC) onto gangue via an acid-base interaction between the positively charged mineral surface and the negatively charged CMC molecule. Thus, the hydrophilicity of gangue minerals is enhanced, preventing the dilution of the concentrate. However, as there is little evidence to support these claims it is important to investigate. Adsorption data and mineral surface charge analyses will allow a fundamental understanding into how electrolytes and their ionic strengths affect gangue-depressant adsorption. It is strongly anticipated that decoupling these effects will allow process operators to tailor their process water quality needs towards best flotation operating regimes and in the long run effect closed water circuits. Thus, using talc and pyrrhotite as proxies, this work investigates the influence of the ionic strength of process water on the adsorption of CMC onto minerals in sulphide flotation.INTRODUCTIONThe phenomenon of gangue depression in mineral flotation is of critical importance as regards the attainment of a required concentrate grade. This thus suggests that the depressant of choice has to have a highly selective affinity for the targeted gangue minerals. This would ensure the necessary prevention of gangue from reporting to the concentrate without inadvertently depressing the value bearing mineral. The chemistry of the environment regulates the manner in which gangue depression occurs. In sulphide flotation, polysaccharides are used as depressants of choice to depress naturally floatable gangue which may in the case of Merensky ores exist as talc. The two widely used polysaccharides in the South African context are carboxymethyl cellulose (CMC) and modified guar gum. It is suggested that polysaccharides depress gangue by rendering the surface of gangue hydrophilic or by preventing the formation of hydrophobic layers on gangue mineral surface, forming large gangue aggregates and thereby increasing their heterocoagulative nature (Shortridge et al., 1999)."

Jan 1, 2018

By Lawrence Bbosa, Aubrey Mainza, Indresan Govender

"Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to develop a probability based model for the power draw of a tumbling mill. Experiments are conducted using dry spherical glass bead charge in a laboratory scale tumbling mill, which is mounted with a torque transducer and tachometer to measure mill power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For both sets of data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. The information from both techniques is then used to develop a model for the power draw as a function of particle size, mill speed and volumetric filling. Predictions of the model match well with measured and calculated values. The model is found to predict mill power within close agreement with measurement and follows trends consistent with existing work on tumbling mill modelling."

Jan 1, 2014

By Markus A. Reuter, Jacques J. Eksteen

The modelling of bath type furnaces tends to be either fundamental in nature or total empirical "black box models". While models of the first kind are robust, they tend to lack accuracy, in cases where they are to be used for process control, and may take an overly long in development time. On the other hand, black box models tend to lack robustness of prediction for all circumstances and tend to be limited to interpolate based on historical data. While this may very often provide short-term accuracy, the models may have problems with stability in the long term. Moreover, the model structure may not reflect any of the fundamental properties of the system and remains opaque to fundamental analysis. The aim of the model development is in obtaining a model that have robustness, high accuracy, a short development time and which is adaptive to a changing environment. The models are specifically developed for on-line decision support or control of furnaces. The modelling approach is evaluated for a chromite bath smelting furnace. The role of systems analysis, mass balance smoothing, thermodynamic analysis are integrated into one generic algorithm for bath type furnaces. Therefore, this paper argues that to understand complex metallurgical furnaces a hybrid approach is the only method to fully grasp the intricacies of metallurgy, to improve operations, economics as well as environmental performance.

Jan 1, 2003

By T. N. Matveeva, L. B. Lantsova, N. K. Gromova

"Multimetal gold-antimony ores are complexed processing products, since they are characterized by veindisseminatedsulfide mineralization with fine-dispersed submicroscopic gold, low content and uneven distribution ofAu, which is concentrated together with iron sulfides (pyrite, arsenopyrite, pyrrhotite). Such ores are classified asrefractory ones and characterized by low gold recovery rates during cyanation. A particular feature of gold-antimonydeposits is the presence of antimony in industrial concentrations therein, along with gold that significantly increasesthe value of these deposits. The main antimony mineral is antimony sulfide - antimonite (stibnite). Gold-antimonyores undergo flotation concentration with producing collective gold-containing concentrates or gold sulfide andantimony concentrates. The purpose of the work is an experimental study of the flotation separation mechanism ofsulfide minerals of copper, antimony and arsenic using tannin-containing modifiers during processing of multimetalgold-bearing ores. During the research it was established that for the selective separation of antimony and arsenicsulfide minerals into concentrates of different kinds, it is possible to use vegetable reagents capable to be selectivelyadsorbed on the arsenopyrite surface. Using the laser KEYENCE VK-9700 and electronic LEO-1420 VP INCA-350microscopy methods, it has been established that the film of a vegetable modifier was not washed off with water andfixed firmly enough on the surface of the polished sections of arsenopyrite. In the X-ray spectrum there are C and Obands related to the reagent structure. The vegetative reagent is fixed both on the pre-adsorbed phase of the collectorand on the areas free from the collector. On the polished sections of antimonite before and after a contact with thetannin solution, only partial adsorbed tannin phases are detected, which disappear as a result of subsequent washingwith water.The reported study was funded by RFBR according to the research project ? 16-05-00646 ?."

Jan 1, 2018

By Y. J. Ferdosi

This paper presents the outcomes of the preliminary investigation focused on the potential usage of Electrochemical Impedance Spectroscopy (EIS) in minerals processing. Currently, Electrochemical Impedance Spectroscopy has been successfully employed in the characterization of multilayer structures formed as molecules adsorb on flat surfaces and is commonly used in bio-related research. Few studies have explored the application of EIS in minerals processing, particularly for mineral particles and flotation systems. In the first series of tests, the impedance response was investigated as a function of particle size, shape and hydrophobicity using model quartz particles. The particle size fractions and the shape were found to contribute to the impedance response. The more hydrophobic quartz particles resulted in a higher impedance values. Further tests involved pure sulfide minerals including chalcocite, bornite, chalcopyrite and pyrite. The AC impedance measurements were conducted as a function of collector (sodium ethyl xanthate) dosage. The AC Impedance data was modeled using the combination of reference circuits. It has been shown that adsorption of collector onto sulfide minerals surfaces results in a higher magnitude of impedance. Increasing the collector dosage resulted in an increase in AC impedance for chalcopyrite, while a decrease was observed for chalcocite. Significant variations in impedance were exhibited by bornite and pyrite with a gradual increase in collector dosage.

Sep 1, 2012

By B. McFadzean, S. Geldenhuys

"Dynamic froth stability tests have found widespread application to quantify froth performance. However, little to no attention has been given to scale parameters in the performance of these measurements. One of the most frequently changing scale parameters in the laboratory scale is the column diameter as this directly influences the amount of material needed for testing. Four different column diameters (50, 100, 200 and 300 mm) were used for this study. Column diameter experiments were done on an industrial scale by means of manual tracking of froth growth versus time. An increase in measured dynamic stability was seen with increasing froth column diameter, which reached a limiting value at large column sizes. It is thought that this behaviour is controlled by the differences in drainage rates of the bulk froth compared to froth in contact with the wall. The column diameter required to represent full-scale froth stability is proposed. A ratio of column surface area to total bubble surface area was used to correct for different column diameters.INTRODUCTIONThe froth phase in flotation contributes significantly to the overall performance of the process (Zanin, et al., 2009). Numerous parameters have been investigated to quantify froth performance, most notably froth recovery (Feteris, et al., 1987; Seaman, et al., 2004; Vera, et al., 1999). Experimentally gathering data to determine froth recovery is challenging and for this reason froth stability has been highlighted as a possible alternative.Froth/foam stability is defined as the time of persistence of the froth/foam and is affected by numerous factors, such as: drainage of the liquid in the lamellae (gravitational and capillary), viscosity at the bubble surface, thickness of the electrical double layer and gas diffusion through liquid films caused by pressure differences between bubbles (Aktas, et al., 2008; Beneventi, et al., 2001). It is well documented in both froth and foam literature that froth/foam stability will heavily influence the performance and appearance of the froth/foam phase (Ata, 2012; Farrokhpay, 2011; Weaire, et al., 2005). Experimentally this has been explicitly proven as an increase in froth stability, characterised by water recovery, usually results in an increase in both valuable mineral and solids recovery (Wiese, et al., 2011; Banford, et al., 1998)."

Jan 1, 2018

By A. M. Amdur, A. N. Matushkina, G. I. Gazaleeva

"The article highlights results of theoretical and practical studies on the enlargement of fine gold in the process of heat treatment. The object of research is refractory gold silicate-carbonate ores of Vorontsovskoe Deposit (Northern Ural), containing fine gold. For setting up experiments and analyzing the results were used the methods of applied mathematics, mathematical statistics, mathematical and physical modeling. Modeling and calculations were performed using the software package HSC Chemistry 6.0, MatLab, setting up a full factorial experiment and other modern modeling methods. Using a scanning electron microscope, the distribution of fine-dispersed ore gold particles by size was studied. It was found that gold particles smaller than 0,4 µm smoothed the vertices and edges, i.e. they are of globules with an amorphous structure. Amorphous materials are nonequilibrium phases with high thermodynamic activity. The physicochemical properties such as melting temperature, diffusion coefficients, the content of metal impurities differ from the properties of the solid phases. In the course of the research were formulated the following scientific bases of the mechanism of enlargement of the gold particles: - the movement of dispersed droplets of gold in the process of external heat to the surface of the ore particles in the pore occurs under the action of thermocapillary pressure; - after melting of the host rock occurs flotation of molten droplets by the bubbles of gases and coagulation of fine gold; - the conditions of flotation drops of gold in oxide melts; floated drops of radius R = 1-100 µm. Analysis of the equilibrium at the perimeter of wetting a drop of gold-oxide melt-gas showed that the scheme of the tension will not significantly differ from the case of solid gold, while the radius of the gas bubbles should be at least 2 times greater than the radius of drops of gold. The proposed method of predicting the results of the enrichment of the proposed scheme, including heat treatment and gravitational centrifugal concentration of crushed ore. Experimental verification of the proposed scheme in the laboratory showed a satisfactory convergence of experiment and prediction. Gold recovery in the concentrate was 33,84 against 33,7 percent forecast. The increase in overall gold recovery to a gravity concentrate after heat treatment is more than 20 %."

Jan 1, 2018

By Matthew Thurley

Optimisation and control of comminution, pelletization, and agglomeration processes is a complex task with large potential for gains in productivity, energy efficiency, and particle size distribution quality. One factor in realising these gains is the requirement for fully-automated online particle size distribution measurement. Moreover, online particle size distribution measurement that is based on the particles on the visible surface and can avoid or mitigate substantial errors that result from under-sizing overlapped particles and over-sizing areas of fines particles. Literature review indicates a body of substantially 2D photographic based particle size measurement systems that suffer from a large number of significant errors except in the simplest case of a monolayer of particles under good illumination with limited color variation in the material. In order to measure the visible particles on a pile there are a number of requirements including; avoiding particle delineation errors due to variation in material color and shadows, detect overlapping versus non-overlapping particles, and identify areas of fine particles as fines and not large rocks. Results are presented using a fully-automated online measurement system of crushed rock on conveyor belt using a 3D surface laser profile. The system provides continuous online measurement and results are shown on over four hours of production after the primary crusher. Size distribution results are calculated using volumetric estimation of the particles on the surface of the pile. The results show a strong capability to discriminate size variation especially in the 10% and 20% passing values. Furthermore results show that if areas of fines are misclassified as large rocks, and overlapped particles misclassified as small rocks, then a near complete loss of discrimination occurs for the P10 and P20 values which become largely constant values.

Jan 1, 2014

By Dingwu Feng, Jannie S. J. van Devente

"The effect of ultrasonication on reactions at solid/liquid interfaces was investigated in two slurry systems, i.e. gold cyanidation and geopolymerisation. The kinetics of gold extraction were significantly enhanced and the cyanide consumption was reduced in the cyanidation of a pyrite concentrate using ultrasonication, probably due to the prevention of leaching passivation, the improvement of the dissolution of the gold host sulphides and the oxidation of soluble sulphides to sulphate. The effectiveness for ultrasonication was improved with the injection of oxygen and the addition of dithiophosphate through enhancing the formation of the oxidation radicals and selectively inducing cavitation bubbles directly at the sulphide interfaces. Ultrasonically enhanced cyanidation could render currently uneconomic deposits viable for extraction by improved cavitation efficiency with the aid of surfactants.Ultrasonication increased the compressive strength of the formed geopolymers through accelerating the dissolution of the Al-Si materials, strengthening the bonds at the solid particle/gel phase interfaces, enhancing the polycondensation process and improving the formation of semi-crystalline to crystalline phases. The use of power ultrasound will yield high-performance geopolymer materials."

Jan 1, 2003

By John A. Rumball, Martin R. Houchin

Data from autogenous and semi-autogenous tests in a 1.67m diameter mill have been analysed in terms of a new model for rock abrasion. This model defines specific rate as the rate of production of fines (material less than 13mm) per unit mass of rock, where the term “rock” is applied to all ore pieces of ore coarser than the grate size. In most cases, an allowance for preliminary rounding and cleavage was made. A method has been developed to analyse steady-state data, using piecewise fitting to the cumulative size distributions. The model was compared to the well-established models, which are based on the population balance method. The specific rate increased for all rock sizes as the volume of 100mm balls in the mill was increased. Tests using a coarser feed and smaller balls provided further evidence that once rocks are rounded, abrasion is due to localised surface damage, caused by impacts, rather than rotational shear. An allowance for rapid rounding of jagged rocks, followed by less rapid abrasion of rounded pebbles was also tested, but the analysis was not conclusive. The average specific rate is a useful measure of the capacity of a primary mill. The effect of power intensity (kW/t of ore) was also investigated as a means of extrapolating the pilot-plant data to large production mills.

Sep 29, 2003

By Darryel Boucher, Raymond Langlois, Neil Rowson, Kristian Waters

The Knelson Concentrator is a centrifugal gravity concentrator composed of a high speed rotating bowl into which a mineral slurry is fed. The rotational motion creates a centrifugal acceleration up to an equivalent of 200 G. Under this acceleration, particles enter fluidised riffles along the side of the bowl, with the fluidisation allowing for the substitution of dense material for less dense. The separation mechanism is not fully understood and questions remain on the optimal residence time, slurry feed parameters and bowl surface profile to achieve a better separation. The positron emission particle tracking (PEPT) technique has been applied to record the motion of a -1700+1180 µm particle of a quartz-gold matrix, labelled with 18F radioisotope while it undergoes concentration inside a 3" laboratory scale Knelson Concentrator (KC-MD3) operated at 60 G. The slurry used was composed of quartz and magnetite. Particle trajectories during the first stage of the concentration process where the heavier particles centrifuge through the increasingly dense slurry towards the riffles of the bowl are shown with respect to time. This work reveals new information on particle motion inside the Knelson Concentrator and the results will be used for validation of developed separation model as well as optimisation of a centrifugal concentrator’s performance.

Jan 1, 2014

By Lei Pan, Roe-Hoan Yoon

"Direct force measurement for bubble-particle interaction has been difficult due to bubble deformation, which makes it difficult to know the separation distances between the two macroscopic surfaces. In the present work, we have developed a method of monitoring the deformation accurately, while directly measuring the interaction forces. In effect, we can ‘see’ bubbles interacting with mineral surfaces under different hydrodynamic and chemical conditions and determine both the hydrodynamic and surface forces involved. In the present work, a high-speed camera has been used to record the optical interference fringes of a thin liquid film (TLF) of water formed on a mineral surface. The recorded fringes are then used to reconstruct the spatiotemporal profiles, from which one can determine the hydrodynamic pressure using the Reynolds lubrications theory. From the forces directly measured in the present work and the hydrodynamic pressures obtained from the fringes, we have determined the disjoining pressure. The results show that air bubbles interacting with hydrophilic surfaces form stable TLFs with zero contact angles. The TLF formed on a hydrophobic surface thins fast, form a ‘pimpled’ film, and ruptures to form a finite contact angle. The new information obtained in the present work may be useful to better understand the role of hydrodynamic and surface forces affecting bubble-particle interactions."

Jan 1, 2014

Mineral flotation is effective over a relatively narrow particle size range of approximately 10 µm to 150 µm. If the upper particle size limit can be increased, however, a run-of-mine ore may be coarse ground, and only the middlings are ground further to achieve required grades. This will result in significant energy savings and increased throughput. In this communication, methods of increasing the upper particle size limit will be discussed on the basis of a flotation model that can predict flotation from both hydrodynamic and surface chemical parameters. An example of increasing flotation recovery by control of a chemistry parameter is given.

Jan 1, 2014

By W. Pawlos

"The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images.Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement. The outlet level of a grain of the same physical properties from the separator is a random variable with normal distribution which modal value is equal to the outlet level of a spherical grain, calculated from the solution of grain movement equations. At these assumptions it is possible to calculate the height of the passage from the separator working chamber to separate a given product with a given separation accuracy, measured by a probable error and to determine separation conditions."

Jan 1, 2003

By G. I. Voiloshnikov, V. E. Dementyev

"One of the most important advances in the world gold metallurgy is the introduction of adsorption technologies for processing of ores and concentrates. «Adsorbent-In-Pulp» process allows to eliminate pulp filtration that is especially important during processing of clay and slime bearing ores. “Adsorbent-In-Leach” process is one of the ways for processing of preg-robbing (carbonaceous) products. High efficiency, increased metals recovery, decrease in capital and operational costs, possibility of easy control and adjustment are the advantages of adsorption processes. Anion-exchange resins and activated carbons are used as adsorbents. This paper presents Irgiredmet experience on gold adsorption technology using both adsorbents (RIP, RIL, CIP, CIL processes). It includes results of long-term studies of different theoretical and practical issues of adsorption processes. Irgiredmet started development of ion exchange technology (RIP, RIL) in 1964. Laboratory and pilot plant tests were conducted to develop process design criteria for 15 RIP plants of the former USSR. During this test work a great number of newly synthesized resins including strong- and medium-base resins was studied, different types of adsorption feed (ores and concentrates) were tested; some theoretical regularities of adsorption process were investigated; the technology of two stage adsorption for silver gold ore, improved flowsheet for gold elution and resin regeneration, designs of technological equipment for adsorption, elution, electrowinning processes including pulsation columns, electrowinning cells etc. were developed. Irgiredmet took part in commissioning of practically all RIP plants in the former USSR. Due to its efforts RIP process became to be the standard technology. Last Irgiredmet RIP projects include the development of adsorption technology using medium-base resin for the three mines owned by GC Petropavlovsk (Amur region, Russia). The complex of the testworks on activated carbon gold adsorption technology including the search of prospective activated carbons; study on gold adsorption mechanism; development, testing and introduction of process flowsheets and the equipment for their realization was conducted. The original gold elution process was developed. The developed CIP technology was firstly introduced at Lebedinsky gold plant (Yakutia). Now carbon adsorption technology is widely used at Russian gold mines as CIP, CIL, CIC processes. The most relevant example of CIP introduction is Svetlinsky gold plant (Ural, Russia) with capacity 8 Mt of ore/ year."

Jan 1, 2018

By Teemu Väyrynen, Matti Vilkko, Antti Jaatinen, Pekka Itävuo

"This paper shows that smooth and accurate feed-hopper level control is essential for consistent cone crusher operation. The objective of the paper is to define the best practices for tight control of cone crusher feed-hopper level. The paper discusses the challenges involved in a delay-dominant level control problem (specifically, dead-time-induced performance and stability issues, mass flow disturbances, process and actuator non-linearity) and proposes five corresponding control structures. The performance of the proposed control structure candidates is evaluated in a simulation study and, finally, a full-scale experiment is conducted for the best-performing candidate. The results of this study emphasize the importance of control structure selection. While the most obvious control structures failed to deliver the desired performance, the best result was achieved by using control structures that eliminate the conveyor transport delay (dead-time) from the control loop. In practice, the control loop dead-time can be eliminated by either using an actuator (variable-speed feed conveyor) that is connected directly to the feed-hopper, or by redefining the process boundaries closer to the used actuator (regulate the circuit mass balance instead of feed-hopper level). The presented control structures provide means to achieve a consistent cone crusher performance and size reduction. This facilitates efforts to improve the plant’s performance and increases the plant’s overall stability."

Jan 1, 2014

By Daniel Saramak

"Issues concerning effectiveness of the high-pressure comminution process in technological circuits of copper ore treatment were presented in the paper. Crushing processes taking place in high-pressure grinding rolls devices (HPGR) are currently one of the most efficient methods of hard ore size reduction in terms of the energy consumption. The HPGR products are characterized by a fine particle size and the micro-cracks formation in individual particles, which appear in downstream grinding processes, decreasing their energy consumption. The purpose of this paper was to analyse the effectiveness of a ball mill grinding process depending on the changeable conditions of run for the HPGR crushing process. The research programme carried out included crushing tests in the laboratory scale HPGR device at various settings of the operating pressure volume and selected qualitative properties of the feed material (i.e. particle size distribution). Particle size distribution analyses of all HPGR products were performed and in the next stage the material was a feed to the ball mill grinding process. Grinding process kinetics were investigated through the determination of mass recoveries of individual particle size fractions after defined grinding time intervals. The models, defining the grinding process effectiveness as a function of changeable conditions of HPGR process run, were determined on the basis of obtained results. Based on these models the optimal grinding time in a ball mill was specified which is, in turn, the basis for optimization of operation of the technological comminution circuits for a given material type. The obtained results proved that the application of HPGR devices in a given copper ore comminution circuit may improve the effectiveness of the downstream grinding process which leads to improvement of the entire circuit work efficiency through decreasing the process energy consumption and enhancing product size reduction."

Jan 1, 2014

By Weiran Zuo, Emmy Manlapig, Fengnian Shi

The effect of metalliferous grains on electrical comminution efficiency was investigated by comparative experiments using natural rocks and synthetic samples. The result indicated that the existence of metalliferous grains affects the breakage probability and product size distribution of electrical comminution. On average, metalliferous grains increased the breakage probability of particle in the first pulse discharge by 55% and generated finer product at the coarse end. As a result, particles with metalliferous grains exhibited higher energy efficiency than that without metalliferous grain in electrical comminution. A positive linear relation between product fineness and specific energy in electrical comminution was observed. With the assistance of numerical simulation on the electrical field distribution of ore particle, the role of metalliferous grains in electrical comminution is confirmed and the mechanism of metalliferous grains effect is elucidated. Understanding of the effect of metalliferous grains on electrical comminution is important to evaluate the feasibility of applying electrical comminution to ores with different mineral composition, and to understand the breakage behavior in electrical comminution.

Jan 1, 2014