Search Documents

"Mineral separation by exploiting the differences in mineral or metal specific gravities (sg) has been used since antiquity. In the modern era, this is most commonly seen in the recovery of gold by the use of centrifugal concentrators and the separation of coal (low sg) from waste rock (high sg) using heavy media cyclones and jigs. Other metals, notably oxides of tin and tungsten, are successfully recovered using some combination of jigs, spirals and shaking tables. However, many conventional gravity separation systems are limited to fairly coarse (>1 mm) to medium (>100 micron) particle separations due to the limitations of the gravitational separation forces in conventional equipment.Many of the high specific gravity minerals of interest are friable (e.g. cassiterite, wolframite, etc.) and excessive fines are generated in the grinding/comminution circuits which cannot be recovered with conventional equipment and may be lost directly to the tailings stream. Recent developments in centrifugal gravity separation equipment specifically designed for fine or ultra-fine particle separation and recovery have resulted in heavy mineral particle recoveries as fine as 10-20 microns. Ongoing research work has also identified the benefit of closed-circuit, multi-stage gravity recovery circuits using some combination of centrifugal concentrators and conventional equipment (tables, spirals, flotation, etc.) which can substantially increase overall plant recovery and final concentrate grade.This paper will provide details of the evolution of non-fluidized bed gravity concentrators for high sg mineral recoveries, correlate laboratory scale development work with plant results to confirm scale-up, and show how recent flowsheet developments have contributed to significantly improved plant performance.IntroductionGravity concentration is one of the oldest and most cost effective metal and/or mineral recovery systems, ranging from the classic hand panning of alluvial gold, through to the large scale production of a wide range of metals and minerals, including gold, silver, PGMs, black sands, coal and iron oxides. Conventional gravity recovery systems, comprised of some combination of sluices, spirals, jigs and shaking tables have limited application in fine particle (i.e. <100 microns) recovery, or where there are limited differences in particle specific gravities (sg), e.g. the separation of high sg, high value metal oxides (e.g. those of tin, tantalum or tungsten), from medium sg, lower value metal sulfides such as pyrite and pyrrhotite. These unit operations tend to have limited capacity, and while double and triple turn spirals and multi-deck tables have been developed, extensive floor space is often required in order to process the tonnages incorporated in the modern mineral processing plant."

Jan 1, 2017

By A. Taylor, J. Shelegey, H. Sullivan, J. Doucet

"Historically, performance at Vale’s Clarabelle Mill was measured by Mill throughput and Mill recovery. After the economic collapse in 2008, a series of reviews were performed to drive improvements in business efficiency. These identified that product quality (e.g., concentrate grade, variability in concentrate grade) had a profound impact on downstream processes and suggested that improved control of these parameters would generate the greatest value for the customer (the Copper Cliff Smelter) and the company (Vale). Consequently, a movement was initiated to transform the Mill operating philosophy to consider customer needs as paramount. Systems and strategies used to drive the transformation are described. In 2011, an unexpected furnace failure resulted in decreased capacity at the Copper Cliff Smelter. In response, a two-stage change in production strategy was developed at Clarabelle. The first stage was to modify the ore blend feeding Clarabelle so that the concentrate grade could be significantly increased with minimal impact on recovery. The second stage was a circuit modification to ensure the elevated concentrate grade could be sustained. Execution of the first stage was complete five days after the failure and the second stage was complete within 10 weeks. Steps involved in each stage are outlined and the overall benefits are presented.INTRODUCTION Clarabelle Mill is located in Copper Cliff, Ontario, Canada (approximately 350 km north of Toronto). The Mill treats copper (Cu) and nickel (Ni) sulphide ores. The primary diluents are pyrrhotite (Po) and non sulphide gangue rock (Rk). The process description of the circuits at Clarabelle is documented in the paper by Taylor, Doucet, Blanchette, Barrette & Lawson (2012) in this Proceedings and will not be repeated. The Mill treats ore containing Cu, Ni and platinum group elements (PGE’s) and produces two concentrates; a Cu concentrate and a bulk Cu/ Ni Concentrate (referred to as nickel concentrate). The Cu concentrate is sold to market while the Ni concentrate is thickened at the Mill and pumped to Vale’s smelter complex in Copper Cliff Ontario for further processing. Since commissioning in 1971, Clarabelle Mill has undergone many circuit changes to suit the changing needs and wants of our customers, both internal and external. The Mill processes ores of varying quality, based on mineralogy and size and until 2009 the Mill daily performance was primarily based on throughput. The second key performance indicator (KPI) of “good” or “bad” performance was quality of the concentrate and third; Mill metal recoveries. There were other plant level KPIs such as flotation feed grind size, slurry densities and mass flows to the separation circuit, but for the most part each day was good or bad depending on how many tons were processed through the Mill."

Jan 1, 2012

By M. R. Saharan

A brief overview of rockburst control measures is presented. The paper then elaborates on one key rockburst control measure, which is known as destress blasting. A historical background of the technique is presented in order to understand different aspects of its field application. The publication enumerates key aspects of the technique as being used in practice in South Africa and North America. The paper also presents an analysis of three case studies in order to demonstrate difficulties associated with the field application of distress blasting in hard rock mines.

Jan 1, 2006

"The application of telerobotics to mining is currently being introduced into production systems around the world. Mining companies in Canada, Sweden, South Africa, and Australia have tended to lead the international charge to this form of technology for mining. While this introduction is taking place, a few basic questions have yet to be answered. How many machines can a single operator run? How many types of machines can a single operator run?A Canadian Research Chair in Robotics and Mine Automation has been established at Laurentian University to investigate these questions and many more through a series of experiments in a telerobotics laboratory that connects Laurentian teleoperation workstations to model mining machines at Cambrian College’s eDome. The laboratory supports many experiments allowing researchers to physically run multiple robot scenarios differing the numbers and types of machines at one quarter scale. Further experiments are being designed to investigate the potential for managing time delays in telerobotics. This paper describes the laboratory, experiments, and some preliminary results."

Jan 1, 2005

By Nick D. Rose

The importance of structural geology in open pit slope stability is overlooked in many mining operations due to pressures to cut costs and minimize mine personnel. As a result, mine geology staff are often unable to keep up with geological mapping of the pit slopes due to other day to day production oriented tasks. In some instances, key structural controls that contribute to slope instability may not be identified until after a slope instability has initiated, at which time it may be difficult or impossible to delineate these features in the field. Even for small slopes, understanding the engineering and structural geology of the rock mass, as well as the effects of groundwater and blasting practices, are of key importance to slope stability. Two case histories are presented as examples of mining operations that experienced slope instability with little more than anecdotal information about the structural and groundwater conditions encountered during mining. By conducting field reconnaissance, simple slope stability analyses and ongoing slope monitoring, practical remedial measures were implemented, allowing continued safe mining operation.

May 1, 2002

By Mostafa Benzaazoua

Les remblais en pâte cimentés sont de plus en plus utilisés dans les exploitations minières souterraines. Une autre alternative d?utilisation du remblai en pâte consiste à le pomper et à le stocker dans des empilements de surface. En plus d?avoir des avantages d?un point de vue de stabilité physique des ouvrages, le remblai en pâte cimenté en surface permettrait également de stabiliser les contaminants dans la matrice du remblai à l?aide du processus de solidification et de stabilisation. Dans cette étude, des remblais en pâte constitués d?un résidu minier sulfuré renfermant beaucoup d?arsenic et de différents liants ont été testés afin d?évaluer la stabilisation des contaminants dans la matrice de remblai. La méthode utilisée pour évaluer la stabilisation et la solidification des contaminants est le test de lixiviation en extracteur de Soxhlet. Les résultats géochimiques issus de ces essais ainsi que la caractérisation chimico-minéralogique des remblais lixiviés ont été analysés pour comprendre les phénomènes chimiques présents dans les remblais durant le temps de cure. Les résultats obtenus montrent que les sulfures présents dans les remblais étudiés (pyrite FeS2 et arsénopyrite FeAsS) s?oxydent et provoquent la dissolution des hydrates les plus vulnérables (dissolution de la portlandite Ca(OH)2 et/ou décalcification des gels CSH). Le calcium produit permet de précipiter les sulfates (essentiellement sous forme de gypse plus ou moins hydraté) et l?arsenic sous forme d?arséniates de calcium plus stables. Les différents liants utilisés donnent des résultats différents en termes de stabilisation et de solidification qui seront discutés dans cet article.

Nov 1, 2002

By Jose R. Hernandez-Aguilar, Jeet Basi

"The study evaluated the impact on overall circuit metallurgy of improving the performance of the two flotation columns that make up the final Mo cleaning stage in the Cu/Mo separation circuit at Highland Valley Copper mine. The results showed that a key factor to improve the overall circuit metallurgy was to control the size of the bubbles generated in the columns. When a large proportion of small (< 1 mm) bubbles were generated, the production rate of solids-in-concentrate increased by a factor of 4-5 compared to typical production figures without compromising concentrate quality. This increase in concentrate production rate reduced the circulating load in the circuit causing a significant increase of Mo recovery. A statistical analysis of historical production data showed a strong relationship between final concentrate production rate and overall Mo recovery. This relationship along with the results from this study indicated an opportunity to increase the recovery of Mo from 90% (typical) to 94% without downgrading concentrate grade. This 4% increase represents about 14,000 lbs or $500,000 worth of Mo each month at current metal prices.To provide a rational interpretation of the results, this study also examined whether the model of Gorain et al. (1997; 1998; 1999) could explain the increase of Mo recovery seemingly resulting from the decrease of bubble size. The data showed that the model predictions did not agree with the experimental data, i.e., for a given change (decrease) of bubble size, the predictions underestimated significantly the observed recovery increase. An interpretation based on the fundamental analysis of Finch and Dobby (1990) and Hernandez-Aguilar et al. (2005) is proposed to explain the discrepancy between measurements and predictions obtained from Gorain et al.’s model.INTRODUCTIONIt is generally accepted that the size of the bubbles generated in a flotation cell – a concept usually referred to as “bubble size” – has a significant effect on metallurgical performance. However, a significant number of mineral processing practitioners often question, with valid reasons, the practical benefits of implementing process improvement strategies based on controlling bubble size. “Small” bubbles are often considered to be “favourable”, but how small they need to be for a particular case, or how to adjust operating conditions to control a target bubble size, or whether the bubbles need to be smaller in the first place are questions that usually remain unanswered. Two reasons explain this situation."

Jan 1, 2009

By Lam. E. K., J. W. Jarvi, B. P. Bharadwaj

"The Rabbit Lake Operation is located in Northern Saskatchewan on the western shore of Wollaston Lake approximately 800 km north of Saskatoon, Saskatchewan.The Operation is owned by a joint venture of Cameco Corporation and Uranerz Exploration and Mining Limited. Cameco is the operator.The Mill started production in June 1975 under the ownership of Gulf Minerals Canada Limited and over the past twenty years has increased the rated production capacity to over twice the original design.The Mill was originally designed to process 485,000 tonnes per year of ore with an annual production of 2.0 million kg of U308 (yellowcake). During the past ten years changes in ore sources and process modifications have led to increased milling capacity and production targets. The Mill has treated a total of 8.6 million tonnes of ore and produced over 40 million kg of U308 in the twenty year period, despite the shutdown and cutbacks in operating time since 1989.The 1995 tonnage throughput was 206,000 tonnes per year. Annual production though has risen to 3.6 million kg of yellowcake despite the departure from full-time to half-time operation in 1991 (7 up-7 down). The forecast for the coming years will see tonnage rising from 300,000 to 570,000 tonnes, production of 4.5 to 5.4 million kg of yellowcake and an anticipated return in the year 1998 to full time operation.This paper will give a brief history of the Mill and focus on the present flowsheet and recent improvements to the process."

Jan 1, 1996

By Turcotte. Yves-Laurent

Notre conférencier, Monsieur Yves L. Turcotte, Vice-président et Directeur général chez Promaintech Novaxa est diplômé en génie industriel de l?Université du Québec à Trois-Rivières et détient une maîtrise en gestion de projets de l?Université du Québec à Montréal. Il est une véritable sommité canadienne dans le domaine de l?amélioration de la performance des organisations. Provenant d&apos;entreprises manufacturières et de services, il possède plus de 20 ans d?expérience en tant que développeur de technologies, conseiller et formateur auprès d?entreprises. Il a à son actif la réalisation de mandats dans plus de 400 entreprises. Il est reconnu pour sa grande capacité d?analyse et pour trouver des solutions novatrices et profitables aux problèmes des organisations les plus complexes. Aujourd&apos;hui, il dirige Promaintech Novaxa, une division de DMR, qui a célébré son dixième anniversaire en 2006. Cette organisation ayant des places d?affaires dans la région de Montréal, Québec et Vancouver compte plus de 50 professionnels et a une carte de visite dans 16 pays. Les axes d?intervention sont le Management, la Productivité, la Fiabilité, l?Innovation et l?Amélioration Continue.

Feb 1, 2008

By Zbigniew J. Hladysz

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, South Dakota, under the sponsorship of the US National Science Foundation (NSF) in cooperation with the US Department of Energy (DOE). This national facility will host a variety of multidisciplinary science and engineering experiments including physics experiments that require shielding from cosmogenic radiation. Geotechnical mapping was performed in 2010 in large excavations of the Davis Campus at the 4850 Level of the former Homestake Mine. LIDAR mapping included laser scanning using a red light laser scanner and 288 Mpixels 360° still camera. The resulting vector map with the photographs digitally draped over the model, was used to create an accurate, virtual model of the excavations. For model verification, the laser scanning was accompanied by surveying and manual mapping of the geology and rock structure. The immediate use of the model was to perform structural analysis and interpretation of geology needed for the design of the DUSEL?s super large excavations. The second round of scanning, after the application of shotcrete to the excavations walls, will be used as a technical blueprint to assess the effectiveness of shotcrete application.

May 1, 2011

By Jan E. Nesset, Julie Fournier, Jorge Torrealba, Colin Hardie

"Gas dispersion studies have been used to benchmark and optimize plant flotation performance for more than a decade, although this technology is not as widely in use as it likely should be based on the significant improvements that have been reported. Part of the reason may be a general lack of awareness within the industry of just what these improvements have been. This paper reviews a number of the reported case studies, groups them into categories of improvement, and draws some general conclusions. The paper will be of interest to plant engineers and technology providers seeking new approaches and tools for improving their own and clients’ processes.INTRODUCTIONThe sector of flotation hydrodynamics that is now known as gas dispersion technology, and the corresponding terminology, had its beginnings in the 1980’s and early 1990’s in the laboratories of McGill University where the students of Prof. J.A. Finch and Dr. C. Gomez conducted studies of gas holdup, superficial gas rate and water recovery on laboratory flotation columns (Laplante et al., 1983; Xu et al., 1991;, Banisi and Finch, 1994; Finch et al., 1999; Nesset, 2011). Sensors were developed for gas holdup (eg), gas rate (Jg) and bubble size (Db) distribution (Tavera et al., 1996: Finch et al., 1999; Dahlke et al., 2001; Chen at al., 2001; Hernandez-Aguilar et al, 2002, 2005). The sensor measurements were rapidly adapted for use in mechanical flotation machines in plant environments (Gomez and Finch, 2002; Gomez et al., 2003; Cooper et al, 2004; Torrealba-Vargas et al, 2004; Nesset et al., 2007). Somewhat parallel developments were being conducted by Gorain and colleagues at the University of Queensland’s JKMRC on pilot and industrial flotation machines using the McGill approach but utilizing alternate sensor designs for eg, Jg and Db (Gorain et al., 1997, 1999; Schwarz and Alexander, 2006) to link flotation kinetics to bubble surface area flux (Sb). Early industrial applications were those led by the university teams from McGill (Canada), the JKMRC (Australia) and the University of Santa Maria (Chile) at plants in North and South America, Australia, South Africa, Asia and Europe. Industrial organizations that brought the technology on-board in the early 2000’s included Teck Resources (then Teck Cominco), COREM, Vale (then Inco), Anglo American Platinum. Several of the major flotation cell manufacturers also purchased the McGill bubble viewer technology for their own equipment studies. The sensors have continued to evolve with multiple and continuous measurement of Jg (Torrealba-Vargas and Finch, 2006, Bartolacci et al., 2008), gas holdup by acoustic means (O’Keefe, 2007) and a combined Jg-Db device called the Anglo Bubble Sizer (Harbort and Schwarz, 2010). A review of the gas dispersion technology use and development have been provided by Gomez and Finch (2002), Harbort and Schwarz (2010) and Nesset (2010)."

Jan 1, 2015

By L. R. Plitt, A. J. Neale, B. C. Flintoff

"INTRODUCTIONThis is not a technical paper in the normal sense. It is an informal document which is intended to share the results of some recent cyclone research with our colleagues both in operations and in research.PILOT PLANT FACILITIESFigure 1 is a schematic of the closed circuit hydrocyclone pilot plant testing facility at the University of Alberta. In this figure the system is configured for some experimental work on wide angle cyclones which was recently completed. The rig is designed to study cyclones in the approximate range of 10 cm to 20 cm diameter. Notable features include the variable speed feed pump, the magnetic flowmeter and pressure sensors on the cyclone feed line and the travelling launder which permits simultaneous sampling of both product streams.ORGANIZATIONFor organizational convenience the subject matter has been divided into three parts:(1) Peculiar Partition Curves(2) Wide Angle Cyclones(3) Rope DischargePECULIAR PARTITION CURVESMuch of the initial empirical mathematical modelling work on cyclone classifiers dealt with homogeneous ores. A homogeneous ore is one in which all particles have substantially the same apparent density, or where one phase is very clearly predominant. In contrast, a heterogeneous ore is one in which there are at least two different density classes, each making a significant contribution to the ore composition. (Particle shape similarity is always assumed.)One of the problems which can arise when analysing the overall solids partition (selectivity, Tromp, etc ... ) curve for a heterogeneous ore is the peculiar shape which may be observed, when compared to partition curves for homogeneous ores. This is not an unusual occurrence and it has been documented by Lynch and Rao, Finch and Laplante and Larsen and Spring. The purpose of this section is to identify those operating conditions which may give rise to peculiar partition curves."

Jan 1, 1986

By P. Chaddock

The Thompson Mill has a capacity of 15,000 T ID of ore and produces two grades of nickel concentrate, copper concentrate and occasionally graphite concentrate. Up to July of 1985 we processed two distinct ore types: T-1 ore, averaging 2. 8% Ni and . 2% Cu and Pipe Open Pit ore, averaging . 8% Ni associated with peridotite and serpentine. Presently our ores from T-1 mine and Thompson Open Pit are of the same type and are processed together. (Figure 1)! n October, 1982, we decided to install an Outokumpu Courier 300 on-stream analyser on an initial 6 streams. The equipment was delivered to the mill on May 2, 1983 and the first analyses were generated by June 17th. The calibrations were 35% complete by the mid-July summer shutdown and were completed in the fall. 1. 2 Analyser Slurry Feed System:The key to successful on-stream analysis is delivery of the sample streams to the analyser.Our system uses pressure-thief sampling for collection. (Figure 2) Initially we used thief samplers modelled after the Outokumpu design, with turbulence bars upstream of the collection point. These units have been replaced with simple laterals as they have worn out. Our thief samplers are mounted vertically on pump discharges and we believe sufficient turbulence exists to ensure representative sampling.

Jan 1, 1987

By T. Krumins, F. C. Ruff, M. Eichhorn, L. Zunti

Hatch Ltd. has recently completed a project to increase refractory gold ore processing capacity at Newmont Mining Corporation’s Twin Creeks facility. The objective of the project was to increase throughput by approximately 10% by adding a third autoclave feed pump to each of the two autoclave circuits. To minimize project capital cost, autoclave feed pumps from Newmont’s decommissioned Lone Tree facility were evaluated and found to be suitable for this new service. The existing pressure oxidation circuit was reviewed in a debottlenecking study to determine other upgrades required to facilitate the increased throughput. Interruption to operations was minimized with a detailed construction plan, supplemented with detailed 3D layout model sequencing studies. The focus of this paper is project development, multi-discipline design considerations, and implementation results.

Jan 1, 2014

By J. G. Price

"The paper reviews state-of-the art welding processes and consumables for structural and pressure equipment applications in offshore environments, particularly the Arctic. Optimum selection of consumables will be discussed with regard to the facility to meet tentative toughness requirements in weldments. Finally, the development of welding procedure specifications will be considered in relation to the prevention of hot or cold cracking and lamellar tearing.Welding RequirementsGeneralThe exploitation of Canadian frontier oil and gas reserves will require a fleet of various types of offshore structures. These will include fixed jacket types and semi-submersibles for the East Coast with huge man-made islands and icebreakers for the Arctic regions. Both these regions will also require supply and drill ships plus subsea pipelines and cargo tankers for transportation. Clearly the welding of these items will plays large part in the over-all integrity and safety of exploration and production operations.The required development in structural steels and pressure vessel steels, for current and future offshore structures, to improve properties, particularly toughness for lower temperature service, has also prompted welding researchers to develop process and consumable combinations to match the parent plate specifications. This development has had to consider particular aspects of weldability such as a low susceptibility to cold cracking and preventing low HAZ toughness. Current research has centred on attempts to increase HAZ toughness with higher heat input welding of newly developed structural steels.The installation of Arctic region pipelines has provided a sound base for future, more complex fabrications in the most severe service temperatures in the Canadian frontier although few of the installations have been designed to the lowest possible exposed temperature of -62°C."

Jan 1, 1987

By Alex Cormode, Carlos Perucca

"Sylvinite ore from the Saskatoon area typically contains about 5% insolubles, occurring as clays and carbonates. These insoluble slimes must be removed sufficiently well to permit an efficient subsequent potassium chloride flotation, due to their high adsorptive capacity for amines used as potash collectors. The insolubles are liberated from sylvinite by high attrition scrubbing in a slurry. The liberated slimes are separated by multistage cycloning or by a selective flocculation-flotation process.An outline of the potash processing operations at Agrium Vanscoy Potash Operations is given, emphasizing the insoluble slimes froth flotation separation process. This process was originally implemented at the Agrium plant in the mid- 1970's and replaced a hydrocyclone system.IntroductionAgrium Vanscoy Potash Operations is located 40 Km southwest of Saskatoon, almost midway between the communities of Vanscoy and Delisle. Processing operations started in 1969, and the annual production capability was subsequently increased to the current 1.8 MM tonnes per year of muriate of potash.The mining operation at Agrium Potash which was described in a paper by Jones and Pruggerl , is done underground using four large continuous double rotor boring machines for the main production with development done by heliminers. Annual ore production is 5.5 MM tonnedannum. Ore is hoisted 1,100 m to surface for processing."

Jan 1, 1999

By D. B. Felsher

"Lakeshore Gold’s Bell Creek Mill is located in Timmins, Ontario. The mill has been in operation since 2009 and has undergone several small expansions since then. In 2012 - 2013 the first major mill expansion was commissioned raising the mill capacity from 2,000tpd to 3,150tpd. This was done through the installation of a new ROM ore truck dumping facility, jaw crusher, ore storage dome, SAG mill, leach tank, CIL tank, and electrowinning cell. This paper will cover the equipment installed to raise the tonnage as well as the commissioning of the new equipment including problems encountered and how these problems were solved.IntroductionLake Shore Gold acquired the Bell Creek Mill, along with the Bell Creek Mine, from the Porcupine Gold Mines Joint Venture, a joint venture between Goldcorp Canada Ltd. and Kinross Gold Corporation, in December 2007.The Bell Creek mill, which processed ore from the Bell Creek Mine has consistently achieved recoveries of over 95%, is a conventional gold mill circuit, involving crushing and two stage ball mill grinding, gravity and leaching, followed by Carbon-In-Pulp (CIP) process for gold recovery. The facility had been placed on care and maintenance in 2002. At the beginning of 2009, the mill had been refurbished with an initial capacity of 800 tonnes per day and was subsequently refurbished to a capacity of 1,500 tonnes per day near the end of the third quarter of that year. The Mill was then expanded in 2010 to a capacity of 2,000 tonnes per day.In late 2011, the Company commenced a 50% expansion of its milling facility, from a processing capacity of 2,000 tonnes per day to 3,150 tonnes per day. Phase 1 of the expansion, which mainly involved enhancements to the solution circuit (“back end”) and increased the mill’s capacity to 2,500 tonnes per day, was completed at the end of 2012. Commissioning of Phase 2 of the expansion, to a capacity of 3,150 tonnes per day, commenced at the end of July 2013."

Jan 1, 2015

By P. Choquet, F. Miller

"The development and testing of a simple low-cost gauge for measurement of tension in a cable bolt grouted in a borehole are presented. Its principle is based on a resistance wire which is wound on a 70 cm length into the spiral grooves of the wire strand cable bolt. Readings are then taken by a robust automatic data logger with a several day autonomy or by a portable readout. In order to have a complete profile of tension along the cable bolt, a number of tension gauges can be installed along its length.This paper provides a description of the development and laboratory calibration of the tension gauge and addresses the two modes of loading for a cable bolt in a rock mass, namely pure tension and shearing at a joint location.In the second part of the paper, four field tests in underground and open pit mines are reported. The first test was used to substantially modify both the gauge and the readout unit principles while the other tests which are still on-going show a very satisfactory behaviour of the modified version of the tension gauge. IntroductionCable-bolting is often used as ground support in Canadian mines for a variety of applications. In underground mines, cable bolts can be installed vertically at the back of cut and fill stopes or in an inclined fashion in the walls of large open stopes. Alternatively, cable bolts at Mines Gaspe (Noranda Inc.) are used in a fan-shaped pattern from a drill drift to stabilize the inclined roof in 25 m wide open stapes. This new application oriented our research efforts toward the design of a novel instrumentation to monitor the efficiency of most commonly used 5/8-inch cable bolts."

Jan 1, 1988

By A. Bamber

Canadian leadership in a global mining context will depend not only on entrepreneurship and best practice but also on technological innovation. This paper argues for more ambition and commitment to R&D for technological innovation in Canadian mining. It focuses on underground hardrock mining, where past R&D initiatives have simply not stood the test of time, and it is important to examine why. Concerns arise because industry’s commitment to R&D has not been sustained over time. Innovation through exploration, processing, and environmental technologies has been more significant. Meanwhile, R&D capacity and synergies in government institutions and universities have not been exploited. There is a need for more commitment, coordination, and collaboration by industry, governments, and universities. This paper examines some corporate models that have achieved sustainable innovation, along with some that have not. A strategy for innovation is discussed that relates to culture, commitment, coordination, and collaboration.

Jan 1, 2005

By Arnaud Faucher, Claude Bazin, Marilène Renaud, Mohamed Mai Manga

"Grinding circuits are operated in the presence of disturbances due to ore changes and equipment malfunctions. One of the challenges faced by the operators is the detection of a disturbance, the identification of its origin and of the action needed to minimize its impact on the process. Hydrocyclones overloading, worn or partly plugged apexes of the units of a nest, surging and internal liner detachment may cause a loss of classification capacity and quality. Recovery losses in downstream leaching or flotation circuits justify the effort in developing techniques for the detection of hydrocyclone malfunction. Two approaches for the detection of hydrocyclone fault are presented in this paper. The first proposed method uses the conventional sensors available in a grinding circuit allowing real time detection of hydrocyclone abnormal operation. The second technique is based on the use of vibration sensors installed on the hydrocyclone of a nest. This last technique enables the classification of the hydrocyclone malfunction as surging, overloading and plugged apex. The two techniques can be combined to increase the robustness of the problem detection.INTRODUCTIONHydrocyclones are used for many purposes ranging from water separation, fines removal and obviously for the preparation of the feed for subsequent concentration circuits in a mineral processing plant. The strategic role of the hydrocyclones for the preparation of the feed to the concentration circuit is often underestimated because of their simplicity of operation and robustness (Napier-Munn et al., 1996; McIvor, 1988). It remains that despite their simplicity, hydrocyclones have been studied extensively from 1970 to 1990 with the objective of developing mathematical models of their operation to be incorporated into grinding circuit simulators (Napier-Munn et al., 1996; Lynch, 1977; Flintoff et al., 1987). Such a development effort is already an acknowledgement of the importance of these units in a mineral processing plant. Several authors (Del Villar et al., 1996; Plitt and Kawatra, 1979; Casali et al., 1998) proposed soft sensors to estimate the classification efficiency of hydrocyclones using sensor measurements. However, few of the proposed sensors are used in the industry. More recently several papers were published to discuss the application of 3-D modelling of the hydrocyclones (Narasimha et al., 2005; Cullivan et al., 2004) and sensors (Bond et al., 1999; Neesse et al., 2003; Hou et al., 1998; Olson and Waterman, 2004; Williams et al., 1995; Willams et al., 1997) to help in the detection of hydrocyclone malfunction."

Jan 1, 2010