Search Documents

By Erica J. Wanless, Ghislain Bournival, Seher Ata, Jose Hamilton Tavares

In froth flotation valuable particles are captured by bubbles and transferred to a froth layer where bubbles are in close proximity. Bubble coalescence frequently occurs in flotation, especially in the froth layer. The coalescence of two bubbles causes a release of energy, which may expel particles from the bubble surface. A series of experiments were carried out to determine the effect of bubble interfacial properties on the detachment of particles upon the coalescence of capillary-held bubbles of 2 mm in size. The interfacial properties of the bubbles were changed by the addition of low molecular weight alcohols, namely 1-pentanol or methyl isobutyl carbinol (MIBC). Using esterified glass particles (? = 43 °) with a 10 % and 90 % cumulative passing diameter of 47.2 and 92.5 µm, respectively, as model particles, it was found a certain concentration of frother, different for each additive, is needed in order to observe a reduction in the detachment of particles. In the presence of frother, the detachment was evaluated at approximately 65 % which was a considerable reduction in the detachment compared with the value of approximately 85 % found in the absence of frother. Frother molecules changed the properties of the airwater interface. Upon the coalescence of two bubbles, the release of energy caused the merged bubble to oscillate; effectively resulting in the detachment of particles. The addition of frothing agents augmented the elasticity of the bubbles, which appeared to be related to the detachment of particles. Whereas frothing agents are generally used to prevent bubble coalescence and stabilise the froth phase, only transient stability is imparted. The results suggested that an additional role of frothers in flotation is to decrease the detachment of particles from bubble surfaces. The type and concentration of frother can be strategically selected to improve metallurgical recovery as an economic incentive.

Jan 1, 2016

By Roger M. Nendick

"IntroductionThe stages of development for bringing a mill into production demand that a flowsheet for the process be developed at an early stage. Detailed engineering of the mill may then proceed without duplication of engineering effort on alternative processes. In the case of gold and silver mills, several process alternatives exist which must be evaluated before the flowsheet is finally fixed. The recently developed Carbon-in-Pulp process has added to this choice.Clearly, the major factor in determining the most suitable process is the amenability of the particular ore to a given treatment. Other factors that will also influence the choice are location, climate, power and water supplies, and available capital.Gold and silver milling processes can be divided into three main types:Gravity Concentration;Flotation;Cyanidation.Combinations of the three are frequently used; i.e. flotation followed by cyanidation of the concentrate, or gravity concentration in the grinding circuit with cyanidation of the classifier overflow. The following are the salient advantages and disadvantages of the three main alternatives.Gravity ConcentrationGravity concentration is suitable for free-milling gold ores, i.e. ores in which the gold is relatively coarse and free from sulphides. It should be noted that just because an ore is high grade, it is not necessarily free milling.Gravity concentration methods include jigs, shaking tables, spirals and more recently Reichert cone concentrators. All methods exploit the density difference between gold, which has a specific gravity greater than 15, depending on how it is alloyed, and the gangue, which usually has a specific gravity range of 2.7 to 3.5.A concentrate grade of several hundred ounces per ton might be produced, but recoveries by gravity alone are generally low in comparison to other methods. For this reason, gravity circuits are usually used in combination with flotation or cyanidation circuits."

Jan 1, 1983

By A. D. Mufch, G. P. Mitchell

"THE HARDY MINE of Falconbridge Nickel Mines Limited is located in Lot 9, Concession 1, Levack Township, Sudbury District, Ontario, 20 miles northwest of the city of Sudbury, and a mile west of the town of Levack. The ore deposit is one of the many nickel-copper sulphide bodies found on, or near, the lower contact of the well-known Sudbury norite-micropegmatite irruptive, and is one of a family of ore deposits which occur on the northwest rim of the irruptive.The property was acquired by purchase in 1935. In the same year a magnetometer survey along the footwall contact of the norite, which is covered by about 150 feet of glacial sands and clays, first indicated the location of the orebody. Drilling from 1935 to 1942 outlined the extent of the ore. Shaft sinking was commenced in the fall of 1951, and the mine is now approaching full production at a rate of about 300,000 tons per year.There are several major differences between the geology of the Levack area and the Falcon bridge area, which lies at the opposite extremity of the irruptive, 28 miles to the east. The purpose of this paper is to describe the essential features of the geology of the Levack area as seen in the Hardy mine, and to supplement the recent papers on other properties in the Sudbury area by Davidson (1), Lochhead (2), and Yates (3).General GeologyA recent review of the regional geology and an extensive bibliography of the Sudbury area can be found in the two papers by H. C. Cooke (4, 5). Some of the recent related references are: Jas. E. Thomson (6), E. M. Abraham (7), Franc. R. Joubin (8), W. G. Q. Johnstone (9)."

Jan 1, 1949

"THE PACIFIC CONTINENTAL MARGIN OF CANADA is de-fined, for the purposes of this paper, as the area sea-ward from the present mainland coast of British Columbia to the foot of the continental slope. It thus coincides with A. Sutherland Brown's Insular Tectonic Belt. The region is limited to the north and south by the political boundary with the U.S.A., the location of which is still in dispute.The region can be subdivided into: (1) an interior trough comprising the Queen Char-lotte, Comox and Nanaimo basins; (2) a medial uplift comprising Vancouver Island and the Queen Charlotte Islands; and (3) a marginal shelf which is extremely narrow (Jess than 5 km) west of the Queen Charlotte Islands, widens to 160 km in Queen Charlotte Sound and is about 35 km wide west of Vancouver Island, where it is underlain by the Tofino sedimentary basin, with its• extension, the Juan de Fuca Basin, at the southern end.The medial uplift consists of a highly disturbed anticlinorium of mainly Mesozoic rocks, with a core of Palaeozoic. The rocks include thick sequences of eugeosynclinal volcanics and sediments. There is strati-graphical evidence of repeated interruption in sedi-mentation. By late Jurassic, the main eugeosynclinal phase was over and a successor basin was initiated in the interior' trough. This became filled, during Cre-taceous and Tertiary time, with sediments ranging in environment from bathyal turbidites to terrestrial conglomerates and coals. West of the medial uplift, another successor basin developed in early Tertiary times and became filled with mainly deep-water marine sediments. A third effusive sequence marks the base of the Tertiary on Graham Island and over most of the Hecate Strait region and Tofino Basin."

Jan 1, 1970

By S. M. Bulataovic, D. M. Wyslouzil

"The Martison Lake phosphate-niobium deposit is composed of unconsolidated residuum containing clay and silt-size particles of phosphate, niobium, iron and clay minerals. This paper deals with the laboratory and pilot plant development of the flowsheet and the reagent scheme to treat the Martison Lake ore. The ore, in addition to the complex gangue composition, contained several phosphate minerals including fluorapatite, francolite and florencite. The detailed laboratory and pilot plant evaluation resulted in the development of an effective flowsheet and reagent scheme for the selective flotation of phosphate minerals using a fatty acid circuit, followed by niobium flotation using amine collectors at acid pH. The developed flowsheet included des liming of ore, magnetic separation, and selective P 2 O 5 -Nb 2Os flotation. The main aspects discussed include characterization of the ore, step by step development of flowsheet and evaluation of dfferent modifiers and collectors for P20s and Nb20s flotation.INTRODUCTIONMartison Lake phosphate-niobium ore deposit, located 75 km north of Hearst, Ontario was discovered in the early 70's and has been the subject of extensive technical-economic evaluation in the late 70's and early 80's.The deposit is covered completely by 30 m to 90 m of glacial overburden and is composed entirely of unconso1idated material called residuum, that lies on top of a precambrian age carbonatite intrusive from which the residuum was derived by weathering and natural leaching in situ. The residuum is and irregularly-shaped horizontal lens, 2 km by 3 km in area, and up to 100 m thick, composed mostly of unconsolidated clay and silt-size particles of phosphate, niobium, iron, mica and clay minerals."

Jan 1, 1986

By A. J. Sinclair

"Abstract-Geology contributes essential information toward obtaining high-quality resource/reserve estimates. In this context, geology can be considered under the following overlapping topics: regional geology, detailed (deposit) geology, mineralogy, ore deposit models and continuity, with geological mapping being fundamental to all. Each of these topics is considered here in terms of potential contributions to "improved" mineral inventory estimation. Some of the principal conclusions are:1. Regional geological relations must be consistent with deposit geology. It is common that important geological relations are more clearly evident in various regional locales than in highly altered and/or highly deformed mineralized areas containing mineral deposit.2. Detailed geology provides information for a geometric model of a deposit, a model that serves as a basis for mine planning. It is important to distinguish fact from interpretation in such models. Substantial effort is required to characterize the geometric margins of a deposit and the relation of these margins to the simplistic geometric form that normally emerges as an interpretation.3. Mineralogical studies relate to many aspects of deposit evaluation including abundance of ore and deleterious minerals, spatial distribution of ore and deleterious minerals, grain size characteristics of important minerals, mill design, etc.4. Ore deposit models contribute substantially to confidence in developing a three-dimensional geometric model of a deposit for mine planning. Specifically, they are a basis on which to develop rules for interpolation and extrapolation of ore, and they contribute to recognition of domains, each with its own characteristic continuity and margin character.5. Continuity is dependent on mineralization style and may be controlled structurally and/or chemically. It is important to distinguish geological continuity and value continuity. A wide range of classical geological methods are useful in examining geological continuity; value continuity is best viewed as a statistical characteristic that is quantified by any of several measures of autocorrelation."

Jan 1, 1998

By F. R. Ploeger, J. H. Crocket

"IntroductionRocks in the Kirkland Lake district form part of the Timiskaming Group, a south-facing homoclinal sequence of wackes, conglomerate, trachytic flows and pyroclastic rocks and syenitic intrusive rocks. Hewitt (1963) indicates that the thickest section, about 5 km, of the Timiskaming Group rocks is attained in Lebel Township. Several writers (Thomson, 1948; Hewitt, 1963; Hyde, 1978; Jensen, 1978; and Downes, 1979) have observed that the Timiskaming Group unconformably overlies the Keewatin volcanics, particularly along the northern contact. Recent work by Downes (1979) in McGarry and McVittie townships to the east of Kirkland Lake has shown that much of what had formerly been classified as Timiskaming actually belongs to an older group of rocks, the Larder Lake Group (Jensen 1978).General GeologyA series of fluviatile, braided-stream sedimentary rocks (Hyde, 1978) form the oldest of the three major rock suites at Kirkland Lake. Conglomerates constitute a large proportion of these sedimentary rocks and typically contain a large percentage of a variety of locally derived alkalic rock clasts as well as the distinctive red jasper iron-formation pebbles (Fig. 1a). The associated wacke units can be massive to finely bedded and are interbedded with the conglomerate. They also contain a large alkalic tuffaceous component.Interbedded with these sedimentary rocks are alkalic extrusive rocks, including tuffs, agglomerates, breccias and flows, which represent episodes of fissure and explosive crater eruption (Cooke and Moorhouse, 1969). The tuffs, although dominantly alkalic in composition, are commonly reworked and contain sedimentary features such as graded bedding, scouring and crossbedding (Fig. 1 b). The trachytic flows are massive to porphyritic and outcrop mainly east of Kirkland Lake in the adjoining townships. Altered leucitic porphyritic flows, locally referred to as red and green spotted trachytes, commonly occur."

Jan 1, 1982

By Ron Davidson

"The Utility Mine in southeast Saskatchewan is owned by Saskatchewan Power Corporation and operated by Mana/ta Coal Ltd. Up to 3.3 million tonnes of lignite is supplied annually to Saskatchewan Power's Boundary Dam Generating Station. The coal occurs in two predominant seams which are covered by up to 37 metres of saturated fine-grained overburden. Overburden is removed by two draglines working in two pits. Coal is hauled to the mine mouth power station. Comprehensive drainage and reclamation programs are integral parts of the operation. IntroductionThe Utility Mine is owned by Saskatchewan Power Corporation and operated by Manalta Coal Ltd. It is located in southeastern Saskatchewan, approximately 200 km southeast of Regina and 8.5 km southwest of Estevan (Fig. 1). The climate of the Estevan area is semi-arid with long, cool winters and short, hot summers. The mean annual precipitation is 42 cm and the mean summer temperature is 20°C; mean winter temperature is -10°C. The Utility Mine supplies coal to the adjacent Boundary Dam Generating Station. Increases in the station's generating capacity during the past decade have resulted in an extensive expansion program for the Utility Mine. This expansion program, the geological conditions present in the area, and the mining/reclamation operations will be highlighted in the following sections<1.2). History The Estevan area has a long history of coal mining. In the early years, coal was mined via entries into coal seam outcrops along the slopes of the Souris River valley. Surface strip mining was introduced in the late 1920s and progressed to the point where it totally replaced underground mining by the 1950s. Surface mining methods are currently used exclusively by all of the Estevan area operators."

Jan 1, 1985

By Ayako Iwakoshi

Highly concentrated pastes of gold nanoparticles were successfully produced by use of a special kind of protective polymer and a mild reductant. Solid part of the pastes consists of up to 85wt% of gold nanoparticles, 10~30 nm in diameter, and residual protective polymer. This component can be diluted by any kinds of solvent at arbitrary rates. Electronics, optics, catalysts, colorants and surface metal coatings are possible application fields. 1. Introduction Noble metal nanoparticles are of interest in a variety of fields ? such as colorants, metal coatings, electronics(1), optics(2), and chemical catalysis(3). Especially, in the color field, the gold nanoparticle has been known as an aesthetic red colorant for stained glass and fine glassware, such as Venetian glass. The mechanism of coloring is attributed to surface plasmon absorption of gold nanoparticles(4,5). The gold nanoparticle in stained glass shows very clear red color, which is very durable for hundreds years. On the other hand, the red color of organic pigment in paint films often fades away within several years. We intended to reproduce the elegant and stable coloring of stained glass in paint films. In order to color a very thin, 20~50?m, paint film like stained glass, production of highly concentrated dispersion of gold nanoparticle is necessary. To achieve this, there were two issues to be overcome. One is how to prevent the coagulation of gold nanoparticles in highly concentrated solution. So far, several methods to prepare gold nanoparticles(6,7) were reported. But only a few methods succeeded to stabilize the gold nanoparticle dispersion at higher concentration than ppm order. The other is controlling of the particle size, this is because the color of gold nanoparticles is very sensitive to the particle size. Only when the particle size lies around 10 nm, the suspension exhibits red color like stained glass.

Oct 1, 2003

By James A. Deeks

"Motor failures and equipment bearing failures are responsible for reduced productivity.With the introduction of computers and data acquisition systems, users are now able to monitor, report and trend deteriorating conditions and take corrective action before a critical shutdown occurs.This paper discusses the monitoring and trend analysis of&apos; motors, and motor and equipment bearings. With today&apos;s digital electronics technology users are now able to monitor their equipment, detect deteriorating or abnormal conditions quickly, alarm the condition locally and or remotely, and decide if immediate corrective action is necessary or if it can be delayed until the end of a work Shift. All of this can be done long before any damage is done to the equipment.Monitoring Trend AnalysisIt is no longer necessary to compromise in selecting products, since state-of-the-art designs allow the adjustment in such small increments that the users are able to detect minute changes in a system&apos;s performance.Monitoring and trending of motors and equipment bearings is now available in economical packages which can be expanded as a system grows. Simply select the information you need, set the parameters, choose the scan time, and decide on the degree of reporting.Buffer storage of short-term monitoring of a number of analogue channels permit the user to view the recent history of motor data such as: motor average load, unbalance, motor current, ground fault, reserve thermal capacity, plus all of the settings of the protective device.A decision can be made to freeze the stored information after the motor stops or after the motor starts. Then the user is able to recall the conditions and diagnose the performance and the cause of the abnormal condition. Typical scan times range from ¼ second to 5 seconds ."

Jan 1, 1992

By D. R. Rice

"The Smoky Valley Common Operation is managed and 50 percent owned by Echo Bay Mine' s Round Mountain Gold Corporation. The other partners with 25 percent each are Homestake Mining Company and Case Pomeroy. The operation in central Nevada includes an open pit, 3-stage open-circuit crushing train and heap leaching on asphalt pads. Presently, about 18,000 tons per day of 0.039 troy ounce gold per ton are transferred to the leach pads, and a similar tonnage of leach residue is transferred to a waste dump. One million tons of ore are being leached at any one time.Gold and silver cyanide are adsorbed from pregnant leach solution on activated coconut shell carbon granules. Pressure stripping desorbs values from loaded carbon to electrowinning solution.Three electrowinning cells are operated in parallel. Each contains six cathodes. Each cathode includes about 40 troy ounces (2.7 pounds) of Number 2 medium coarse steel wool. The wetted area of each cathode is about 24 by 30 inches. Solution flow is 2 to 3 gallons per minute per electrowinning cell. Average current flow is 25 amperes per cathode. The voltage is controlled in the range of 3 to 4 volts to maintain desired amperage.Twice a week two cathodes are pulled from each cell and drained. Each cathode is split into four portions. These are put in a steel pan coated with WD-40 and dried overnight.Each dried cathode portion is put into a paper sack. Each group of four sacks corresponding to a cathode is weighed together. The typical weight ratio of loaded cathode wool to new cathodes is 9 or 10 to 1. To each sack is added 35 troy ounces of silica, 45 troy ounces of anhydrous borax, 35 troy ounces of nitre, and 5 troy ounces of fluorspar. The sacks are taped shut."

Jan 1, 1986

By S. Sagar

In September 1996, Dofasco commissioned a 165 Mt twin shell EAF furnace and an associated ladle fleet. During and after this startup, refractory performance in the ladles was optimized on a holistic approach through several initiatives that increased ladle refractory retention times from 7000 to over 16000 mins (160 heats). This dropped the overall refractory costs by 40% while ensuring a consistent and predictable ladle performance. One initiative that drove enhancements was the proper brick selection for each particular refractory area and it&apos;s process conditions. The work concentrated on the selection of a resin bonded alumina magnesia carbon (AMC) brick in the barrel area of the ladle, upgrades to the 2 piece monolithic alumina cast ladle bottom and increasing the slagline refractory brick quality with the appropriate zoning/paneling. The adoption of a magnesia alumina carbon (MAC) brick in the transition area of the barrel/slagline has also improved performance and predictability. The design developments have lowered the overall wear rates and balanced the service life of the entire ladle. Safety was improved and breakout potential reduced by changing the safety lining from a high alumina brick to a state of art technology - monolithic shotcrete lining. This initiative decreased the overall manpower required to brick a ladle and increased shop ladle availability. The ladle bricking area environment was also improved by adopting a post combustion device to burn phenol fumes from ladle preheating practices. This has improved the overall health & safety of the reline teams. The consistent and predictable performance of the ladle on a whole has allowed the shop to decrease the number of working ladles in operation from 5 to 4. This further decreased wear rates from over-oxidation and excessive thermal cycling, saving approximately $500,000 in natural gas from pre-heater operations.

Jan 1, 2004

By Jerry Z. Lu

Belt conveyor design involves the evaluation of belt tensions, drive selection, pulley configuration and other technical issues. The conveyor belt tensions vary with conveyor layout, drive pulley configuration, belt selection, and idler selection. The decisions for the belt conveyor construction always take all technical, commercial and maintenance issues into consideration. A good conveyor design shall provide required operational features and at the same time be cost effective. The common issues for an engineer to face during belt conveyor design include: (1) Conveyor drive selection ? drive with fluid couplings or variable frequency drives; (2) Drive system configurations - single pulley large drives or dual pulley smaller drives, if intermediate tripper booster drives shall be applied, what power ratio should be adopted for a multi-drive conveyor; (3) Gear reducers ? shaft mount drives, right angle gear reducers or parallel gear reducers; (4) Drive pulley lagging - ceramic lagging or rubber lagging; If ceramic lagging, what type should be used. (5) Conveyor speed variation ? If conveyors run at variable speeds, faster speed/lower percentage loading or slower speed/higher percentage loading. In many cases the decision maker find themselves in a dilemma ? technical benefits vs. financial benefits, capital cost vs. operational cost, and capital and operational cost vs. maintenance effort. Although many conveyor design topics above have been discussed in numerous technical papers and design reference books, management executives and inexperienced engineers may be confused and feel lost. The consultation of people around them may lead to different opinions since experiences tend to vary, making the decision making process complicated. The purpose of this paper is to simplify these complicated issues and provide useful guidelines for belt conveyor design. This paper focuses more on providing simple and practical answers and solutions instead of discussing each topic academically and theoretically in depth.

Nov 1, 2011

By A. J. Sinclair

Abstract-Exploratory data evaluation is an essential part of every high quality, mineral inventory estimate. Efficient analysis involves a thorough organization of available quantitative data that are the basis of the estimate and perhaps the formation of composite grades. Data organization and evaluation can involve more than 50% of the time necessary to conduct a mineral inventory estimation. The principal purpose of exploratory data evaluation in mineral inventory work is to improve the quality of estimation by providing insight into characteristics of the variables under investigation. Specific aims include: (1) to recognize and eliminate errors; (2) to provide a comprehensive knowledge of the statistical characteristics of all variables of interest for resource/reserve estimation; (3) to document and understand the interrelationships among the variables of interest; (4) to recognize systematic spatial variation of variables such as grade and thickness of mineralized zones; (5) to recognize and define distinctive geological domains that require independent estimation of mineral inventory; (6) to identify and characterize outliers; and (7) to evaluate similarity/dissimilarity of various types of raw data, especially samples of different supports. These aims are not mutually exclusive but they can all have their own impact on resource/reserve estimation. Error must be minimized. Individual variables can have characteristics that lead to different decisions in the course of estimation. Similarly, interrelations of variables might contribute to the ease (or difficulty) with which estimates of several variables can be obtained. Trends can impose the need for two or more domains, each of which might be estimated independent of the others. Outliers, a perennial problem, require detailed evaluations because they impact on reserves much out of proportion to their abundance. Data, of widely different supports, generally must be standardized if all are to be used for purposes of estimation.

Jan 1, 1998

By N. Maleki

Magnesium matrix composites are widely used in automotive and aerospace industries for achieving higher performance due to their light weight. The Mg2Si intermetallics compound in Mg/Mg2Si composite exhibits many excellent properties such as high melting temperature, high hardness, and low thermal expansion coefficient. However, under normal cast conditions, the primary Mg2Si phase exhibits coarse Chinese script or dendritic morphologies and the eutectic structures is very brittle resulting in the low ductility and strength of the alloys. Modification treatment is a very effective method to obtain fine microstructure and improve the mechanical properties of the alloys due to low production cost. In this investigation various amount of bismuth addition have been carried out on Mg?5wt %Si alloy to refine and modify the morphology of coarse Mg2Si in order to improve the corrosion resistance of the composite product. The effect of Bi content on microstructure of Mg2Si/Mg composite was investigated by optical and scanning electron microscopy followed by EDX analysis and X-Ray diffraction. In order to compare corrosion resistance of unmodified and modified specimens, Immersion test and potentiodynamic polarization (PD) were used. The results showed that by Bi addition, the size of primary phase Mg2Si was considerably reduced and the morphology was modified from a coarse dendritic shape to a polyhedral shape. The results also indicated that the corrosion resistance of Mg?Si alloys was improved by the addition of 1%wt of Bi due to the reduction, refinement and evenly distribution of Mg2Si phase. Indeed, both the morphology and distribution of Mg2Si intermetallic had a great influence on the corrosion behavior of Mg/Mg2Si composite.

Oct 1, 2011

By Carmen Mihaela Neculita

Sulfate-reducing passive bioreactors efficiently treat acid mine drainage (AMD) by increasing its pH and alkalinity and by removing metals as sulfide precipitates, in addition to hydroxides and carbonates. However, the new mining legislation sets discharge limits based on physicochemical parameters and on the non-toxicity of treated effluent as well. In this study, toxicity was assessed for effluent from 3.5 L column bioreactors filled with mixtures of natural organic carbon sources and operated at two different hydraulic retention times (HRTs) of 7.3 d and 10 d for the treatment of a highly contaminated AMD. Acute toxicity was observed for D. magna, and a toxicity identification evaluation (TIE) procedure was performed to identify potential toxicants. To help the interpretation of the toxicity results, metal partition in the effluent was also determined by filtration and ultrafiltration, while geochemical modeling was performed for metal speciation evaluation. The 10 d HRT effluent was nonacutely lethal for rainbow trout but acutely lethal for D. magna, whereas the 7.3 d HRT effluent was toxic for both organisms. The toxicity to D. magna was eliminated by 2 h of aeration for the 10 d HRT effluent, and the TIE procedure suggested iron as a cause of toxicity. However, the 2 h aeration eliminated the toxicity of the 7.3 d HRT effluent, only if performed after the pH rising to 9.3. Data regarding metal speciation indicated instability of both effluents during aeration and were consistent with the toxicity being caused by iron. The study indicates that design of passive treatment should include sufficient HRT and posttreatment aeration to meet acute toxicity requirements. Keywords: acid mine drainage, sulphate-reducing passive bioreactors, hydraulic retention time, effluent toxicity, metal speciation

Nov 1, 2008

By E. P. Cadwell

"Throughout the years Cyanamid has been a supplier of cyanide and a supplier of information to the mining industry. In general, the knowledge of mineralogy is greatly overlooked. Mineral deposits in the Western hemisphere have been exceedingly rich in the past but now they are becoming poorer. In other words, we will have to use our talents to the utmost to extract the precious metals and base metals from these ores. Modifications of some of the mineralogical equipment displayed here belong in the mill.Cyanidation of copper has been one of the main projects in our labs in recent years. De-rimming or de-filming of copper in order to upgrade copper concentrate was the main aspect investigated. A study was made as to how wide spread was the filming of secondary copper on pyrite, and to what extent it affected the copper industry. It was very wide.Often there is no conception as to what the minerals are. One open pit copper producer with a chalcopyrite ore was producing a copper concentrate with a 5% copper value whereas chalcopyrite contains 35% copper. They used primary and secondary grinding and a regrinding section. The ore contained about 8 parts chalcopyrite to one part of other copper minerals. In tests, a 3 1/ 2% copper rougher concentrate, cleaned without regrinding but conditioned with cyanide for a low contact time of 30 seconds produced a 30% copper concentrate with 90% recovery by removal of the film. It was of utmost importance that some quantitative mineralogical analysis be made before flow sheet changes were made. Every man should be trained to do his own microscopic examination in order to get quick answers. The fundamental thing in all mineral dressing is to first of all know the minerals and the mineral associations."

Jan 1, 1964

By T. E. Newkirk

In the past few years there has been considerable controversy on the most suitable material to be used in ventilation doors which will have to serve also as fire doors. For this reason it was thought useful at Mclntyre to find out to what extent our zinc chloride treated spruce doors were fire resistant and what protection we could expect in case of an underground fire. The doors to be tested were constructed of the same material as that used in our regular ventilation doors underground, namely, 2-inch tongue-and-groove well seasoned spuce. It is to be noted, however, that whereas the dimensions of the ventilation doors are 5 ft. by 6 ft., those of the test doors were only 14 in. by 17½ in. The treated doors were made up from lumber that l1ad been treated with chromated zinc chloride, as described in Mr. Keeley&apos;s paper. Two kinds of tests were carried out: a heat test and a flame test. An electric muffle furnace for assaying, equipped with a pyrometer, was used for the beat test, the furnace door being replaced by the wooden door to be tested. In the flame test, the door to be tested formed one end of a rectangular steel box in which was placed a large blow-torch. Air was admitted at the rear of the box. A pyrometer recorded the temperature at the inside surface of the door where flame impinged. The results of the tests are presented in the accompanying table, in which the word &apos;failed&apos; is to be interpreted as meaning that the door had been damaged to the extent that smoke, but not necessarily flame, issued from its outside surface.

Jan 1, 1949

"These guidelines have been prepared to assist the Qualified Person(s)in the planning and supervision of exploration programs which will be reported under National Instrument 43101. The Companion Policy of NI43101 references the guidelines and states that issuers and Qualified Persons should follow them.Exploration Best Practices GuidelinesPreamble: These guidelines have been prepared to assist the Qualified Person(s) in the planning and supervision of exploration programs which will be reported under National Instrument 43-101. Such exploration programs must be under the supervision of the Qualified Person who will be responsible and accountable for the planning, execution and interpretation of all exploration activity as well as the implementation of quality assurance programs and reporting. These guidelines are also recommended for use in the planning and execution of exploration programs which will not be reported under NI 43-101. This set of broad guidelines or ""best practices"" has been drawn up to ensure a consistently high quality of work that will maintain public confidence and assist securities regulators. The guidelines are not intended to inhibit the original thinking or application of new approaches, that are fundamental to successful mineral exploration.Results should be summarized and reported in a Technical Report of good professional quality in accordance with the National Instrument 43-101 and Form 1 contained in that instrument. All exploration work from which public reporting will ensue must be designed and carried out under the supervision of a Qualified Person (""QP""). A QP is defined in National Instrument 43-101 as an individual who is an engineer or geoscientist with at least five (5) years' experience in mineral exploration, mine development, mine operation or project assessment, has experience relevant to the subject matter of the project or report and is a member in good standing of a recognized professional association."

Jan 1, 2003

By Horatio Sam-Aggrey, Margot Hurlbert

Small Modular Reactors (SMRs) have been touted as having the potential to spearhead a nuclear renaissance. Proponents of this view cite the relative advantages of SMRs over larger nuclear plants as reason for their optimism. Some of these merits include potential economies of mass production deriving from modular factory production, enhanced safety features, the ability to locate reactors in remote areas, and reduced requirements for technical workforces to install and maintain SMRs. Despite the optimism surrounding SMRs, nuclear power is still a contentious issue for many Canadians. The growth of nuclear power remains adversely affected by concerns over issues such as: the health and safety consequences of nuclear power generation, environmental impacts, proliferation of nuclear materials, terrorism, and radioactive waste disposal (Organisation for Economic Co-operation and Development (OECD) and Nuclear Energy Agency (NEA), 2010). Personal values, past nuclear accidents, and lack of trust in the industry are other factors influencing attitudes toward nuclear energy (IAEA, 2005). In Canada, three main areas where SMRs could be used have been identified. These include: a. Traditional, on-grid power generation, especially in provinces looking for zero-emissions replacements for CO2-emitting coal plants. B. Remote off grid communities that currently rely on diesel or fuel oil power generation. There are 279 off-grid communities in Canada, many of them being Aboriginal communities (NRCan, ND). Notably, all communities in each of Canada’s three territories qualify as remote. C. Resource extraction sites, such as mining and oil and gas extraction sites. Many of Canada’s principal producing mines and active mineral exploration projects are located within close proximity of Aboriginal communities. Any proposed implementation of small nuclear plants would, require the support of the local population, which is largely Indigenous in the northern regions. The possible deployment of SMRs raises important issue relating to consultation and accommodation of Aboriginal concerns regarding potential SMR deployment. This is especially pertinent given Canada’s pending implementation of the provisions of UNDRIP. One of the provisions of UNDRIP that has attracted a lot of attention is the one on Free Prior and Informed Consent (FPIC). Drawing on previously published information, this paper discusses some of the challenges posed by FPIC for the deployment of SMRs. The next section outlines the provisions of FPIC and its implementation in the Canadian context. Section 3, details some of the challenges posed by FPIC to the deployment of SMRs, while Section 4 provides some concluding comments.

Jan 1, 2020