Search Documents

By Richard Simon

This paper presents an ongoing study on the use of borehole breakouts to estimate in situ stresses at depth in a Canadian underground mine. Breakouts were identified using an acoustic televiewer (ATV) probe. Rock samples were tested in a laboratory to determine their failure curve. Breakout analyses were performed using a 2D failure criterion and a multiaxial failure criterion. Analyses were carried out using both short-term (peak) and long-term strengths (the latter considered here as being represented by the damage initiation threshold DIT). The analyses have shown that the use of the longterm strength and a multiaxial failure criterion leads to results that are more consistent with stress measurements performed in the field, in the vicinity of the mine.

Jun 1, 2012

By P. Zhang, K. Liu, L. Ou

"The strength and mechanism of Portland cement prepared from stone coal vanadium slag were studied in this paper. Initially, the slag was used as silicon raw materials to prepare clinker. By blending the prepared clinker with gypsum, waste, and fly ash, a series of different grades cement got well prepared. All of performances of the cement were up to the requirements of China’s national standard. The hydration products and microstructure of cement were identified and analyzed by X-ray diffraction and scanning electron microscopy. With the comparison of cement hydration characteristics at different ages, the strength formation mechanism of cement was clarified. The experimental results suggested that adding the fine materials (mainly waste and fly ash) to replace part of clinker would accelerate cement hydration, as it provided additional surfaces for the nucleation and growth of hydration products. And the hydration products were similar to ordinary Portland cement, mainly containing the amorphous calcium silicate hydrates (C-S-H), acicular ettringite (AFt) and portlandite (CH). With hydration time increasing, the hydration products continuously covered the cement particles, resulting in a thicker surface layer. As a result, it gradually condensed into a dense structure block with small pores and smooth surfaces, which led to higher strength. In conclusion, using the vanadium slag to prepare Portland cement can realize the utilization of solid mineral wastes, which will bring huge ecological and economic benefits.INTRODUCTIONWith the development of China’s mining industry, more and more mineral waste residue is discharged every year. These solid wastes cause varieties of resources and environmental problems on people’s living area. While at the same time, the demands of cement are increasing with the remarkable development of the construction industry. Thus, in recent years, utilization of proper solid waste to prepare cement has become an efficient way to deal with the solid mineral wastes problems (Boncukcuoglu, Kocakeri?M, & Tosunoglu, 2002; Simatupang, Hanafi, Purwasasmita, Imran, & Pane, 2012; Tsakiridis, Papadimitriou, Tsivilis, & Koroneos, 2008; Yun, Yong, Choi, Lee, & Lachemi, 2009)."

Jan 1, 2016

MR. J. F. MYERS, Consulting J3eneficiation Engineer, Greenwich, Conn.: In the written discussion contributed by Mr. F. C. Bond in item ( 2) (page 515), speaiking about the significance of the ratio of mill diameter to the make-up ball diameter, he states: "When this ratio exceeds 100 the power and capacity of the mill are de-creased"; and the paragraph ends with a reference to the 30 per cent ball volume "with some de-crease in mill capacity". I believe this broad statement is incorrect. When we are dealing with a non-cataracting mill, pre-ceded by a good rod mill, there is a slight increase in capacity, but the power does drop. The second point that I consider needs consideration is Mr. Bond's item (8), Proper Mill Speed (page 516). This paragraph should be qualified to cover single-stage mills only. It does not apply where a rod mill is followed by a non-cataracting ball mill. The statement as is, with no qualification, gives an erroneous idea of proper mill speeds.

Jan 1, 1957

By T. C. Murphy, W. Taciuk

In 1966, the Iron Ore Company of Canada commissioned a wet magnetic scavanging plant for the recovery of fine magnetite values p.resent in spiral tailings discharged from a spiral gravity separation process. The plant includes dewatering, grinding, classification, thickening, mini-wedge screening, and primary, secondary and tertiary wet magnetic separation stages. The source of feed varies in quantity and quality, so the original design included variable operational procedures to deal with these conditions.

Jan 1, 1972

By H Zorychta

Based on underground measurements made at the Nova Scotia coal mines of the Dominion Coal Company, Limited, this paper presents a comparison between the physical properties of hardwood packs and steel friction props when used for longwall support. The probable loads sup-ported by steel friction props on a longwall face at both the Dominion No. 20 Colliery and the Princess Colliery are delineated, and the results of the tests are presented in graphical form. It is concluded that the steel friction props are more efficient than the hardwood packs that they replaced as roof supports. Introduction AN evolution in the methods of longwall face support is taking place in the Sydney coalfield. Longwall face support had consisted primarily of timber props and hardwood packs. In 1957, however, at the Princess Colliery, Sydney Mines, Nova Scotia, the first longwall was equipped with steel friction props. At the present time, eleven longwall faces are supported on wood and sixteen faces are carried on steel friction props.

Jan 1, 1965

By Michael W. Hinds

X-ray Fluorescence Spectrometry (XRF) is used at various stages of gold refining. Initially, incoming impure gold is analysed for deleterious elements such as As, Cd, Hg, Se, and Te. Based on the levels of these impurities the material can be returned to the client or accepted for refining. XRF is also used to determine the metal concentrations after the impure gold has been melted and sampled. This information is used to assist the final Fire Assay determination of gold and silver. An energy dispersive XRF is used to determine the end point of chlorination refining step.

Jan 1, 2011

By Guoxiang Chi

This paper consists of two parts: the first part describes the principles and functionality of the BsnMod program, and the second part presents preliminary application of this program to paleo-fluid flow modeling in the Anticosti Basin. The BsnMod program simulates fluid flow and heat transfer during the evolution of sedimentary basins through numerical solution (finite difference method) of three partial differential equations, which describe sediment compaction, fluid continuity, and heat conservation. It can be used to estimate the evolution of fluid overpressure, flow rate, and temperature during the basin history. The program was written in C++, works under Windows environments, and has a user interface allowing inputs in dialogues and outputs in both tabular and graphic forms. The program was applied to the Lower Paleozoic Anticosti Basin in eastern Canada. The basin history consists of a passive margin stage and a foreland basin stage. Preliminary simulation results indicate that no significant fluid overpressures were developed in the passive margin stage and during the early period of the foreland basin stage, but strong overpressures were developed within the foreland basin succession during the middle and late periods of the foreland basin stage. Fluid flow rates were generally slow, and thermal profiles were not significantly disturbed by fluid movement throughout the basin history. Potential source rocks of hydrocarbons were found in the foreland basin succession. The strong overpressures in the foreland basin succession could have been a major driving force for hydrocarbon migration from the source rocks to the underlying potential reservoir rocks.

May 1, 2001

By Lizelle Glaner

An investigation was carried out by Mintek to investigate the influence of additions of gold to ?Fecraloy?, alloys based on Fe-Cr-Al. The aim was to try and improve the oxidation resistance of the ?Fecraloy? alloys at elevated temperatures over extended periods of time. The ?Fecraloy? alloys are very oxidation resistant alloys already employed in industry as substrates for metallic catalysts in auto-catalyst systems for high performance cars. Since their life and durability is limited by the slow, but steady, oxidation of the substrates, any change in the growth or stability of the oxides could be an improvement.

Oct 1, 2003

By Mark Sherman, M. Dennis, Raj Rajamani

"The two Alumbrera 36ft (10.97m)dia. SAG mills were sized, using the FDW ""Grindpower 'I program, to treat an average of 1852 tph each. This paper describes how modelling of the shell lifter design, using the Millsoft program, identified milling inefficiencies caused by poor charge motion. This explained the ""as built"" circuit's inability to achieve the throughput rates predcted by the circuit's designer. Use of the Millsoft program to design a new, dramatically different lifter configuration, in conjunction with a different approach to variable speed drive utilization, has resulted in an improved charge motion and a 30% increase in hard ore milling rates. The new lifter design has allowed the designer's predicted average throughput rates to be achieved.IntroductionThe Alumbrera project grinding circuit consists of two 36ft dia. X 17ft EGL, 13 500 kW, variable speed, gearless drive SAG mills coupled to four 20ft dia. X 30ft EGL, 6 000 kW fixed speed, gear driven, ball mills. The circuit is configured as two identical grinding aisles, each consisting of one SAG mill and two ball mills. No pebble crushing circuit was installed due to the expected absence of a critical size fraction in the first years of production. However, the grinding circuit layout does incorporate space for a pebble crushing retrofit. At present, only about 5% - 10% of the new mill feed reports as trommel oversize and is recycled back to each SAG mill using a water cannon.The circuit was designed to be ball mill limited and to treat the four major Alumbrera ore types at rates varying between 68 000 tpd, and 89 750 tpd, depending on ore hardness. Average throughput rate, and hence nominal design rate, for the grinding circuit was 80 000 tpd (1 852tph per line at 90% availability)."

Jan 1, 1999

By Juan Asalgado

The JORC and NI43-101 codes impose that mineralized material has a reasonable prospect of economical extraction to be classified as Mineral Resource. For deposits close to surface and amenable to open pit mining, it is easy to show reasonable prospect of economic extraction running a Lerch-Grossman optimization. The Lerch-Grossman pit provides a transparent and repeatable way of separating the Mineral Resource (within the pit) from the remainder of the mineral inventory (outside the pit). Deposits amenable to underground mining are more challenging because of the variety of the underground methods. AMEC developed a stand-alone software package that outlines the material which has reasonable prospect of economic extraction for open stoping, block caving, sublevel caving and room and pillar. The software takes a block model file in ASCII and exports a 3D surface outlining the part of the mineralization that has a reasonable prospect of economic extraction, and which the Qualified Person can smooth out manually if required.

Oct 1, 2009

By Denis Blackburn

La Direction générale du développement de l?Industrie minérale (DGDIM) du ministère des Ressources naturelles et de la Faune (MRNF) du Québec tient un inventaire de toute l?activité minière sur le territoire. Cet inventaire s?est enrichi, au cours des dernières années, d?un grand nombre de projets dédiés au fer ou à des substances qui y sont associées (titane, vanadium, phosphate). Actuellement, cinq régions du Québec sont principalement touchées par la recrudescence de projets dédiés au fer : Fermont, Schefferville, Baie d?Ungava, Baie-James et Chibougamau. Fermont et Schefferville sont les régions les plus actives. Les infrastructures en place, telles que les routes, les chemins de fer, les ports, les lignes électriques et les municipalités, ont atteint, dans certains cas, leur capacité et de nouvelles infrastructures devront être construites pour satisfaire les besoins. À la Baie-James et sur le flanc ouest de la Baie d?Ungava, des projets d?exploration sont aussi en cours. Le manque d?infrastructure pourrait peser lourd sur le développement de projets miniers dans ces régions. Enfin, dans le secteur Chibougamau/Matagami et à quelques sites ailleurs au Québec, des projets d?exploration qui visent le vanadium, le titane ou le phosphate pourraient aussi fournir comme produit secondaire des concentrés de fer. Tous les projets, décrits dans cet article, sont situés sur le territoire du Plan Nord du gouvernement du Québec.

May 1, 2011

By F. Vagnon, A. M. Ferrero, M. Pirulli, A. Segalini

"The topic of this study is the design of flexible fences to mitigate the risk due to debris flow phenomena by means of theoretical and experimental studies analysed in framework of the Rock Engineering System (RES).The study of the interaction between debris flows and flexible barriers is a major challenge since many different aspects concerning both the slope characteristics and the structure features are involved. Debris flows are often triggered by the mobilization of debris deposits that are generated by rock fall of adjacent rock walls. The rock debris deposits are difficult to be characterized by the physical and mechanical point of view due to their large variability in volume distribution and, moreover, when dealing with high mountains environment, they are also strongly affected by the presence of water at different phases (solid or liquid) depending on the temperature. The debris deposit turns unstable in relation with the geotechnical and environmental features of the areas and the instability evolution in high mountain steep valley is often a debris flow. Debris flow destructive potential is very high and protections are often needed to reduce the debris flow risk.This complexity determines the needs of comprehensive study able to include the global basin dynamic and the environmental conditions. An a-priori analysis of the influence of the different aspects can be useful to focus on the real driving aspects of the problem. Due to the complexity of the system the application of the RES methodology is recommended in order to clearly define the different assumptions needed, their influence on the simulations and a comparison among them.RES allows investigating triggering criteria, flow and depositional processes and interaction of flows with protection fences in a rational way. For this purpose, an interaction matrix is created: it summarizes the key geotechnical parameters that influence debris flows, their interactions and debris/engineering protection opera behaviour. The goal is to quantify the diagonal-off terms to assess the residual risk after barrier construction, using back analysis from real debris flow event and data collection from literature.This methodology is applied to analyze a debris flow event in the Italian Western Alps where numerical analyses are carried on to assess flow characteristics to be used for fence design through the application of an analytical and numerical model developed by the authors (Brighenti et al, 2013). In particular, the velocity and deposition heights have been estimated using the numerical code RASH3D (Pirulli, 2010), which is a single-phase model based on depth-averaged Saint Venant equations. Pathways of different lengths are studied to assess the input data necessary to design the protection barrier and to determine the associated risk. Simulation of the barrier at different places along the valley will also allow to determine optimal barrier location in terms of minimum residual risks by comparing the velocity, the volume and the energy of the debris after the barrier impact.The work will produce a possible design scheme to be adopted in this environment."

Jan 1, 2015

By Amir Zavichi

Today, with the necessity of timely, on-budget and high quality completion of projects, proper use of construction equipment is essential to ensure project success. Construction equipment places a large monetary burden on the project and if not utilized efficiently, it can result in economic losses. Cranes are one of the most important and expensive operational devices on construction sites. They play a central role, and often activities that rely on crane services fall on the project?s critical path. Currently, material-handling scheduling is done by the crane operator or by an on-duty superintendent using his/hers personal judgment, making the process manual and timeconsuming. Thus, developing an optimal schedule, which considers different dynamic constraints in construction job site, may not be possible based on the current practice. This leads to longer operation times and a negative impact on project cost. This paper presents the latest results of an ongoing study, which aims to design and implement a nearreal time crane operation decision support system to be utilized directly by the crane operator or as an aid for the superintendent in scheduling optimal operation services. This system has several advantages such as maximizing the efficiency of crane operations, guaranteeing the best operation possible to reduce the crane?s travel time, reducing crews and equipment idle time, and minimizing the dependence on subjective human judgments.

Aug 1, 2013

By V. Labiouse, F. Orellana

"Hollow cylinder samples can be tested for both the characterization of rock properties and the physical modelling at reduced scale of engineering applications. Particularly, this type of experimental setup can be used to simulate different stress conditions around underground openings, as already developed in the petroleum engineering field e.g. to study the instabilities around deep wellbores during either drilling or the oil production phase. Some authors have also used this technique to successfully characterize the damaged zone around underground openings in the tunneling engineering field looking for an efficient design of their support.This article presents a new hollow cylinder testing device developed at the Rock Mechanics Laboratory of the Ecole Polytechnique Fédérale de Lausanne (EPFL), Switzerland. It allows a full and independent control of the confining pressure and pore water pressure conditions at both the inner and outer boundaries of Thick-Walled Hollow Cylindrical samples. In order to mimicking a tunnel excavation in a porous rock mass, after initial recovery of the in-situ stress and pore water pressure, the hollow cylinders are subjected to a decrease in the internal confining pressure. Moreover, X-Ray Computed Tomography scans of the specimens are performed through the testing cell before and after the mechanical unloading to monitor the displacements undergone and the sample damage. The equipment, testing procedure and data analysis techniques are briefly presented in the paper.The good performance of the apparatus has already been checked on weak rock specimens, among others on Boom and Opalinus Clay samples. In many configurations, the mechanical unloading is found to induce a Damaged Zone (DZ) around the central hole. Its geometry and extent show a great similarity with in-situ observations around tunnels driven in the Boom and Opalinus Clay formations. Such similarities contribute to increase confidence in the understanding and modelling of the ongoing processes."

Jan 1, 2015

By S. Ando

The fatigue crack growth behavior of magnesium single crystal has been investigated, CT (compact tension) type specimens with different notch orientations were prepared. In the case of notch plane and direction are (1-210) and [10-10], fatigue crack propagates parallel to notch, From TEM observation, it is found that pyramial slips occures at the crack tip. When notch is normal to basal plane, a fatigue crack propagates [0001] and parallel to basal plane depending on stress intensity factor range, In the case of notch parallel to basal plane, a fatigue crack propagates through straight route with some {10-12} twin, Fatigue crack growth rate, da/dN of A- and B- specimen is lower than F-specimen with crack parallel to basal plane.

Jan 1, 2004

By Douglas R. Schmitt

In general, knowledge of the state of stress within the Antarctic lithosphere remains largely unconstrained due in part to Antarctica?s inaccessibility and because of the paucity of seismic focal mechanism solutions. As such, an important component of the ANDRILL project was to acquire new information on the stress directions and magnitudes within the upper crust. Extensive fracture mapping of the core and oriented ultrasonic televiewer logging were carried out to provide strong constraints on both stress orientations and the faulting regime. The first hydraulic fracturing stress determinations in Antarctica were also carried out to provide complimentary stress magnitudes. These measurements were accomplished using a wire-line transported hydraulic fracturing system consisting, essentially, of two synthetic polymer packers that were inflated to isolate the 1-m long pressurization interval. The tests were conducted at the end of the drilling and logging in a ~130-m section specially drilled below 1000 mbsf (nearly 1500 m from the rig floor) for hydraulic fractures. This zone was drilled primarily through competent, dense, and low permeability diamicts. The core fracture and televiewer logging information was used to site twenty separate measurements. Classic hydraulic fracturing pressurization records with unambiguous breakdown and fracture closure pressures were obtained in about half of the measurements. The remaining tests provided fracture propagation and closure pressures that are consistent with the classic breakdown curves, but they did not include a clear breakdown pressure and are indicative of the reopening of either natural or drilling induced fractures in the wellbore wall. The preliminary analysis of the results are in generally good agreement with the stress directions indicated by the core fracture logging and the stress regime suggested by the character of the drilling induced core fractures.

Jun 1, 2012

By S. Radacina Rusu

The satellite-based global positioning system (GPS) has significantly changed the way site operations are carried out in surface mining. The GPS has impacted safety, productivity, fleet efficiency, and maintenance practices. However, no comparable global localization system exists for underground mines. This paper discusses recent work in the application of ideas from the mobile robotics research community to the problem of real-time vehicle positioning in underground drift networks. Related previous work recently focused on the creation of globally consistent 2D maps of underground environments that possess sufficient detail to be used for underground localization. Our current work entails the development of a GPS-like system for mobile mining equipment, with results given from both laboratory and field experiments.

May 1, 2011

By Vladislava A. Ignatkina, Victor D. Samyguin

"Within the limits of two-phase approach, considering mass transfer with pulp and air streams was shown that each bubble appears to be an elementary carrier, transporting particles from the collection zone into the froth. The kinetics of flotation was described by the exponential equation in which first order flotation speed constant has to be replaced with two-phased coefficient of a mass transfer. Criteria of selectivity of two ore fractions separation, based on determination of optimum time at which maximum difference between extractions and components content in separated fractions were offered. An interrelation between optimum time of pulp residence in a flowing chamber of a flotation machine, time of bubbles mineralization and an optimum airflow has been ascertained. Cumulative criterion of mass transfer efficiency of flotation process has been ascertained to be a form of the spectrum and its position on axis of three-phase coefficient of a mass transfer.INTRODUCTIONRegularities of a mass transfer of three bearing streams: pulp stream, air stream and froth stream underlie theory of mineral complexes flotation (Samygin, Filippov, & Shekhirev, 2003)However, only description of mass transfer in pulp stream by means of kinetic equations that were simple and convenient for practical use, has gained a full distribution (Tykhonov, 2009;Rubinstein&Filippov, 1980; Saleh, 2010).Within the limits of a single-phase approach, the role of gas stream in increase of speed and selectivity of flotation, was associated with an improvement of hydrodynamic mode. An influence of particles and bubbles sizes (Rubinstein&Filippov, 1980; Rubinstein&Samygin, 1998, Samygin et al., 2003; Dai, Fornasiero,& Ralston, 2000), of pulpflow and airflow (Finch& Dobby, 1990) and turbulent energy intensity (Shubert, 1979; Massinaei, 2007) on the flotation process has been studied. It was stated that flotation selectivity is increasing by means of gradual airflow increase from first to final cameras of the impeller flotation machine (Aslan&Boz,2010; Finch, 2011) and by means of using a multizone flotation machine (Samyguin, Filippov, Matinin, Lekhatinov, &Tertyshnikov, 2013)."

Jan 1, 2016

By M. Li, T. H. Dubaniewicz, H. N. Dougherty

"INTRODUCTION Underground mines have the risk of accumulation of gases if not ventilated properly or during and after emergency situations when ventilation controls become damaged or stop working. Common gases that are monitored in underground coal are carbon monoxide (CO), oxygen (O2), and methane (CH4). Methane is a gas found in coal and released through mining; its explosive range is between 5% and 15%. Methane is commonly monitored on all mining equipment and with handheld gas sensors carried by most underground coal miners. Fiber optics (FO) is a popular technology applied in underground mining, particularly for its electric isolation. Many miners are familiar with FO cables hung throughout the mine, which are primarily used in the communication of voice and data (Taylor et al. 2010). Advancements in laser and fiber optics have made this technology well suited for gas sensing the harsh environment of mining applications. The work of the U.S. Bureau of Mines on the use of fiber optic monitoring of gases in mines started in 1992. Dubaniewicz et al. (1992, 1993, 1995, 1999, 2003) developed prototype gas sensors, including methane gas sensors, for research purposes. Previous research (Dubaniewicz & Chilton 1992) identified potential fiber optic gas detection cross-sensitivities associated with the index of refraction of various gases. Index of refraction effects was noted for carbon dioxide (CO2), which is produced in significant quantities by mine fires or explosions. NIOSH released a broad agency announcement (BAA) for the development and demonstration of mine safety and health technology (CDC NIOSH 2017). The objective of this announcement was to validate a sensor, specifically fiber optic, for the mine environment and test it in an actual working mine. The RSL FO sensor “OptoSniff” provided from this work is capable of hundreds of sensing points over distances of up to 20 km, has a measurement range of 0.05% to 100%, senses in an oxygen- deficient environment, and has no gas cross-sensitivity (RSL, 2014). The RSL system is totally electrically passive outside the central control unit (CCU), which can be housed in an MSHA-approved explosion-proof (XP) enclosure or in a control room outside of the permissive area. The sensor was tested in dusty and signal loss situations, showing it is tolerant of dust, has functioned at signal losses up to 90%, and was successfully tested in a mine environment for a five-month period (Walsh et al. 2014). This paper describes how the RSL FO sensor is used for testing using smoke and its contaminants for applicability in emergency situations. The testing investigates individual contaminants such as CO2, temperature, and smoke. Each test was performed separately and methane concentration, laser power, and response time data were collected."

Jan 1, 2019

By A. Galibois, H. Monette, J. L. Collins

This paper deals with the problem of caving, which occurs in varying degrees in blast holes before loading. It is shown that the distribution of the amount of caving in materials may be described by a gamma density function. A decision model to determine the optimal depth of over-drilling 'in order to minimize the expected additional cost per hole is described. Two different policies are discussed. In addition, charts which permit the mine operator to realize significant savings have been drawn for different actual situations.

Jan 1, 1971