Search Documents

By Oxenford R. J

An important rutile-ilmenite-zircon bearing sand deposit was discovered by local farmers at Eneabba, 300 km by road north of Perth in 1970. These heavy minerals occur in a series of ancient strandlines and associated dunal deposits at elevations from 85 m to 170 m above the present sea level and are situated,30 km inland. The strandlines were deposited on wave- cut platforms in an ancient bay bounded by Mesozoic sediments during a series of regress- ions from a high sea level, probably during late Tertiary or early Pleistocene times. The immediate source of the heavy minerals in the Eneabba deposit is a widespread low content of those minerals in the nearby Mesozoic sedi- ments. The high-grade southern portion of the Eneabba deposit has been closely drilled and is now being prepared for production by Allied Eneabba.Pty. Ltd., a subsidiary of Allied Minerals N.L. This part of the deposit is 11 km long and up to 2.5 km wide. It is characterised by little or no overburden and the average depth of mineralisation, bounded by a 2.5 per cent heavy mineral cut-off, is 12 m. The water-laid strandline deposits at the base of the mineralisation are generally high grade, ranging from 20 to 60 per cent

Jan 1, 1973

This paper presents the water management plan of the Mae Moh Project in the North of Thailand, which includes a large lignite opencast mine and thermal power plants. Lignite production will increase from the present 5.5 million tons per annum to approximately 20 million tons per annum by 1995 when the pit area will be about 20 sq.km. and the depth at over 300 meters. Seven power plants are proposed of which two are under construction. The total capacity to be installed is 2,925 MW. The principles considered for water management are firstly flood protection, including drainage of the mining pit and diversion of the Mae Moh stream away from proposed future mining areas; and secondly, a plan to meet the water requirement of the thermal power plants, while maintaining downstream supplies for irrigation and other purposes. The limited annual run-off of Mae Moh and Mae Chang watershed basins are inadequate for the proposed power plants. A study has been prepared to compare two approaches, namely conveying water from remote watersheds to meet the water requirement of the power plants up to total installed capacity; or by limiting future total generation, at the existing site, to only 2025 MV.

Jan 1, 1988

By Golding D

The Charters Towers goldfield is located in the centre of a Lower to Mid-Palaeozoic igneous complex where schistose, amphibolite-grade metamorphic rocks were intruded by multiple phases of medium grained granodioritic rocks. Several generations of mafic and felsic dykes also occur. Two distinct mylonites cut all but the youngest granitoids. Gold mineralisation occurs in quartz veins located in brittley reactivated mylonite and in sympathetic fissures in the undeformed granitoids. The gold-quartz veins occur in complex, gouge-filled, 2.5m thick zones, with minor sulfides, surrounded by zoned phyllic and propylitic alteration assemblages. Four main vein systems are each restricted to separate granitoids or contain oreshoots near granitoid contacts. No genetic relationship between the granitoids and the vein systems can be documented. The early mylonitic fabrics and the granitoid contacts played an important role in ground preparation and in the localization of oreshoots. Non mylonitized granitoids also served as favourable hosts for many of the lodes. Whole rock values of 180 of the granitoids range between 6.5 and 7.9 per mil. Hydrothermal vein quartzes have 180 values between 12.2 and 15.7 per mil. Mylonite quartzes have values of 8.4 per mil. Variation in 180 values of quartzes is in part related to granitoid host rock type.

Jan 1, 1987

The grade (or value) to volume relationship which constitutes a target orebody is used to show that the concentration of diamonds in an economic deposit may be as low as O.Olg/t. Diamond valuations from an Indonesian deposit demonstrate that the largest 5% of the diamonds in the deposit contributed 25% of the mass of diamonds recovered and 70% of the value from the ore. The need to consider the large stone content and the probability of recovery is used to estimate that the sampling density is required to be as high as 4-10,000ppm for a VLC deposit. This is compared with an acceptable sampling density for a bauxite deposit of 700ppb. A case history of the discovery of a diamond bearing paleo-channel in the Ellendale field in Western Australia illustrates that the sampling task becomes impractical. It requires an excavation in excess of 300,000 bcm of material to prove a 5M hem ore reserve. The conclusion is reached that setting up a small scale mining operation is an appropriate method of proving such an ore reserve and that the Code of Reporting should allow a category of "Mineable Resource" to cover such a situation.

Jan 1, 1990

Flue gases from electrical power station boilers, roasting, metallurgical and chemical plants could be treated by flotation using conventional flotation machines. The flue gases are introduced into the pulp instead of the air. The flotation media is a suspension of Ca(OH)2 or CaCO3 or a solution of NH4OH etc containing Na oleate as collector and frother. The SO2 and dust content of the initial flue gases were experimentally reduced by 100 to 1000 times in one flotation operation. The velocity of the flue gases through flotation machines could reach approximatively 0.4 to 0.5 m/s and more against 1.5 m/s reached in scrubber absorbers used for this purpose, but the quality of purification is expected to be better for flotation, which is essential for the cases of heavy polluted metallurgical and chemical flue gases. For some chemical plants the flue gases flotation media may be different and more suitable as compared to the above mentioned media. The proposed flotation method could be used for separation of dry grinded ores in the form of aerosols, with a realisation of flotation from a closed space (gas bubble in the pulp) onto the interface liquid-air where the particles are attached inside the bubbles.

Jan 1, 1993

Cyanidation tests by bottle agitation were conducted on an oxidized lead-silver ore containing approximately 12% Pb and 500 g/t Ag. Over 60% of the silver was leached when the ore was ground to 100% passing 0.15mm, whereas 50-60% of the silver was leached when the ore was only ground to 100% passing 0.5mm. Slurry handling and dewatering at the fine grind size were very difficult due to the high clay content of the ore, however this problem was greatly reduced at the coar- ser grind size. The silver recovery at the fine grind size was very dependent on cyanide solution strength with stronger cyanide sol- utions (containing more than 0.1% NaCN) re- sulting in lower solution silver contents. This was thought to be due to the precipi- tation of leached silver by zinc, which was also leached from the ore by the higher cyanide levels. There was a critical zinc level in solution of approximately 1000ppm, above which the silver recovery fell markedly. Cyanide and lime consumptions for this ore were high (typically 5 kg/t and 40 kg/t respectively), hence the processing of this particular ore by cyanide leaching is un- economic at current silver prices.

Jan 1, 1987

By B J. Monaghan, R J. Longbottom, D J. Pinson, S J. Chew

Recycling steel plant by-products is a critical issue for achieving both environmental and economic sustainability of integrated steel plants. A key steel plant by-product stream is dust from basic oxygen steelmaking (BOS), which can be recycled back to the BOS vessel as iron units and to aid slag formation. The major limitations for its recycling are zinc and the uncertainty in zinc speciation of the dust. This uncertainty affects the amount of dust recycled and how it interacts with the slag during processing. BOS dust in stockpiles can undergo self-sintering reactions that oxidise the iron-bearing components. As this occurs, zinc (or oxide) may combine with iron oxides to form a zinc-iron spinel solid solution phase. Knowing which zinc-bearing species are present in the BOS dust is a key aspect in understanding and developing an efficient recycling process for the dust. To overcome difficulties associated with phase identification in the BOS dust (both fresh and selfsintered), particularly the magnetite-zinc ferrite spinel solid solution using X-ray diffraction (XRD) / scanning electron microscopy (SEM) / energy dispersive spectroscopy (EDS), high end characterisation tools, transmission electron microscopy (TEM) and Mössbauer spectroscopy, were also used. Such an approach allowed improved phase identification of key zinc- and iron-bearing phases that were not previously resolvable. The zinc in fresh BOS dust was mostly present as extremely fine separate particles of zinc oxide, attached to the iron particles. These extremely fine particles were <10 nm in size. Additionally, a small amount of zinc ferrite was also identified within the sample (most likely contained within a magnetite-zinc ferrite spinel solid solution). However, the zinc in the self-sintered BOS dust, was found to be present entirely in a magnetite-zinc ferrite spinel solid solution. While this spinel phase had been previously identified by XRD, it was not clear that it contained zinc. The Mössbauer results provided definitive evidence of zinc within the spinel phase.

Jun 19, 2024

By B Hayes

The Ambuklao and Binga Rehabilitation Project is a 175 MW hydro power project currently under construction across dual sites in the north region of Luzon Island, Philippines. When it was built in 1956, the Ambuklao Dam harnessed the second largest hydro-electric reservoir in Asia. However, due to landslide erosion and prolonged silt infiltration caused by an earthquake in 1990, the power plant has been rendered inoperable since 1999.To bring the power generating facility back to life, the project scope entails the rehabilitation and construction of civil structures, shafts and tunnels. A major component of these works is the decommissioning of a section of the seven metre diameter headrace tunnel by installing a concrete plug. The headrace tunnel is part of a closed waterway system that connects the dam via a shaft, exhibiting a hydrostatic pressure of 13 bar (1300 kPa) at the location of the new tunnel plug. In addition, the power station ball valves have seized ajar and the damaged intake riser is unsafe toaccess thereby requiring the plugging operation to be carried out under live flowing conditions.Working under hydrostatic pressure and live conditions, the headrace plug will be an underwater tremie pour operation that includes drilling and concrete injection through blow out preventer caissons installed in the floor of an underground chamber above the tunnel. The purpose of this paper is to describe the key engineering and planning components involved in this operation including pre- and post-grouting, chamber crane, sonar, local water compensation, jet flushing, drilling, caisson installation, and concrete design, production, delivery and placement. The success of this task rests on the strategic preparation and operational management of risk and safety in a challenging rural environment.

Mar 8, 2011

By S Brunt

A new elution process has been developed for the recovery of gold thiosulfate from ion exchange resins. This is a synergistic system which utilises a base eluent, such as nitrate or trithionate, along with an additive that improves the elution of gold. The use of the additive enables lower eluent concentrations to be adopted, as well as weaker eluents such as chloride. With the chloride + additive system, complete gold elution can be achieved within 12 BV when utilising an eluent flow of 5 BV/h. When the eluent flow is reduced to 2 BV/h, complete elution is achieved within 8 BV. Similar results are obtained when using nitrate or trithionate as the base eluent. A copper pre-elution process has also been developed, whereby the majority of copper can be stripped within 5 BV prior to gold elution. This method is a significant improvement on the ammonia + oxygen pre-elution previously suggested. The development of a new analytical procedure based on ion chromatography with UV detection is also described for the quantification of polythionates in leach solutions and loaded on resins. This enables analysis to be carried out for resin-in- leach type processes where the polythionates are being formed in solution and simultaneously adsorbed onto the resin.

Jan 1, 2007

By Finch JA, Uribe-Salas A

The relationship between the process variables and hydrodynamics of a downflow concurrent column (Jameson cell) was investigated in both two and three-phase systems. Gas holdups from 10 to -60 per cent were obtained at gas rates up to 15 cm/s (STP), liquid (slurry) rates up to 25 cm/s, frother concentrations of 5 and 25 ppm, and slurry density (silica) up to 1.23 g/cm3 ina 3.8 cm diameter, 190 cm high column with a 0.5 cm diameter nozzle. Gas holdup decreases with feed rate and increases with gas rate, reaching a maximum (-60 per cent) at a gas rate to feed rate ratio of about one. Gas holdups were higher with slurry compared to water as feed. Stable operation was difficult to maintain at high gas rates especially with low frother dosage; operation was not possible without some frother. Instability was characterised by loss of pool level or formation of slugs. The slugs could move up or down or remain oscillatory. A quantitative relationship between the variables and gas holdup or onset of instability was not identified. Conductivity and pressure-based techniques were successfully tested on-line for estimation of gas holdup and to judge the state of operation (eg formation of slugs).

Jan 1, 1993

By S Lehane, S Pearce

The characterisation and assessment of waste rock has been the subject of considerable research, and many guidance documents have been published both internationally and within Australia. While these documents provide detailed information on how to characterise waste rock, there is not a great amount of detail on how to determine the optimal waste management options from an operational viewpoint. For example, typical questions that a mine operator would seek answers to include: What placement method should be used (eg end tipping versus paddock dumping)? What is an optimal tip head height for waste placement in a storage facility? How should sulfide grade control be carried out?Defining the contributing factors to waste management and waste material placement and assessing the contribution of each variable directs these assessments towards a semi-qualitative and quantitative methodology. Quantitative methodologies show an increase in the confidence of these assessments by providing logical, measureable assessments.As part of a strategic assessment for waste management at an active mine site, a detailed risk-based investigation of the influence of variables common to waste placement was completed. These variables included placement method, placement height, sulfur grade and material conditioning (eg compaction) on the associated risks of waste material storage. The assessed risks include temperature assessments (potential for thermal take-off as a result of spontaneous combustion), toxic gas production and flow and acid production potential. Applying a numerical modelling approach to the assessment of the different waste material placement strategies allows for the variation in risk to be graphically presented and communicated through risk matrices and histograms.CITATION:Pearce, S and Lehane, S, 2015. Quantitative risk assessment tools to assist with waste management and placement guidelines, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 353–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R M. Krek

The haulage system used to convey ore from an underground mine to a surface stockpile at the mine process plant is a vital component of the mine’s overall infrastructure and economic viability. The system selected has a significant impact on the set-up of the mine and the access to the underground mine. In turn, the set-up of the mine and the access to the underground mine have a significant impact on the system.A number of haulage technologies are available to transfer the ore from the underground workings to the surface stockpile, including hoists, conveyors, rail and trucks.This paper focuses on the shaft hoisting and inclined conveyor haulage technologies. These technologies have been used consistently to deliver ore from at depth and/or at high tonnage. Previous reviews of the appropriate vertical haulage systems have nominally been restricted to the respective systems only, with no consideration for any other scope or issues that may affect the selection. The selection of the appropriate vertical haulage system, whether shaft hoisting or inclined conveying, needs to consider numerous key factors.CITATION:Krek, R M and Northcote, A E A, 2014. A holistic viewpoint for selecting the vertical haulage system – shafts and conveyors, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 289–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By J R. Taylor, J A. Muchan, S M. Pape, B S. Davis

Acid and metalliferous drainage (AMD) is routinely derived from waste rock, tailings, pit wall rock, underground mine voids, heap leach pads, ore stockpiles, concentrate stockpiles and even slag piles. In many jurisdictions, there is an assumption that tailings materials represent the highest AMD risk. This is likely due to their highly sulfidic and ultra-fine grained nature, and the fact that they occur in large tonnage, partially unsaturated deposits. These characteristics are not unreasonably associated with reactive and therefore highly polluting mine waste materials. Interestingly, however, the high sulfide content and highly reactive nature of tailings achieves the rapid consumption of oxygen in tailings pore spaces. This oxygen depletion can limit or halt sulfide oxidation throughout much of the tailings pile. Oxygen can only be resupplied to the tailings via atmospheric exchange at the air-tailings interface. The grain size of most tailings materials limits this resupply to a diffusion related process that only affects the uppermost 100–2000 mm. Hence sulfide oxidation in tailings can be inherently self-limiting. Unfortunately, the same cannot be concluded for waste rock materials.Using a unique site assessment strategy that focuses on quantifying acidity fluxes from various domains at a mine site, it has become increasingly evident that sulfidic waste rock produces the majority (typically 60–80 per cent) of the soluble acid and metalliferous pollution at most active and decommissioned sulfide-bearing mine sites. Whether sulfidic waste rock is disposed in engineered above ground facilities, backfilled into pits or even underground voids, it remains the primary source of pollutants for decades to centuries.Conventional end-dumping waste rock practices result in angle-of-repose pathways for air and water, and these internal fabrics exacerbate sulfide oxidation (ie pollution generation) and discharge from waste rock materials. The primary aim of many cover systems is to retard the access of air and water to these conduits. Recent thinking is that more emphasis needs to be directed at strategic waste rock pile construction practices, and less reliance placed on thin soil cover systems to prevent AMD.Waste rock pile construction approaches that minimise porosity and permeability but raise the retained moisture content and enhance water residence times have the potential to lower sulfide oxidation rates and thereby improve water quality outcomes. For example, innovative base-up, layered and compacted (BULC) waste rock piles have the potential to avoid or minimise the generation of AMD, supersede the need for treatment and facilitate successful closure and relinquishment across the mining sector (Figure 1).CITATION:Taylor, J R, Pape, S M, Davis, B S and Muchan, J A, 2016. Waste rock pile construction to lower closure and relinquishment costs, in Proceedings Life-of-Mine 2016 Conference, pp 97–99 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By A Hocking, S Henderson

Commonwealth of Australia (2016) defines rehabilitation as comprising “the design and construction of landforms as well as the establishment of sustainable ecosystems or alternative vegetation, depending upon the desired post-operational land use”. For open cut coal mines in Queensland and New South Wales, the question of how to apply this intent to pits at mine closure is repeated for hundreds of individual pits. In EISs, closure plans and public discussion, assorted treatments are proposed to rehabilitate pits. While some aspects of final voids have been intensively studied, there is little guidance on how to choose a final void treatment option that delivers the optimal outcome against rehabilitation goals. For example, in the Bowen Basin and Hunter Valley commonly proposed rehabilitation actions include reducing the angles of pit walls; however, with few voids successfully rehabilitated to date there is limited understanding of what different wall slopes will achieve.CITATION:Henderson, S and Hocking, A, 2018. A decision framework for comparison of coal void rehabilitation options, in Proceedings Life-of-Mine 2018, pp 127–130 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By N Lewis

Recent major urban trunk sewer infrastructure projects in Melbourne have involved construction of nearly 10 km of tunnel boring machine (TBM) driven tunnels in a range of geological conditions varying from soft alluvial soils to hard volcanic rock. To provide both construction and permanent access to the new trunk sewer network, a total of 17 shafts between 5 m and 13 m in diameter, and up to 64 m in depth have been constructed. This paper describes the design and construction of the temporary shaft support systems for the shafts.The range and variability of geological conditions at each shaft site required the adoption of the following shaft support systems across the projects – jet grouting, sheet piles, diaphragm wall, secant pile, contiguous pile, reinforced shotcrete rings and rock bolts.Groundwater control, settlement, TBM launch and reception chambers at the shaft base, chambers and TBM launches at mid-depth of shafts, connection shafts between new and existing sewers and bypass pumping shafts are among the challenges that have been met.This paper reports on the some of the challenges involved and experience gained in developing design and construction solutions for large diameter shafts that are excavated within varying geology in Melbourne over the past three years.

Mar 8, 2011

By T Nassis, P Louw, M R. Fry, T du Toit

Business intelligence (BI) and business analytics (BA) are established IT technologies that are used extensively in the business environment. This paper discusses the use of these technologies in production environments and beneficiation plants.Assmang’s Khumani mine is an iron ore operation located in the Northern Cape, South Africa. Assmang Limited is jointly owned by African Rainbow Minerals Limited and Assore Limited. This paper presents a case study of a BI solution applied to this plant, which is used by metallurgists, supervisors and all levels of operations and management to extract and analyse data to control and optimise the operation of the plant.The main advantage of adopting an established BI solution is the ease with which production personnel can extract and analyse data. The data is easily presented in familiar spreadsheets and no IT staff or specific training is required to achieve this.The solution adopted at Khumani mine uses a data mart with a multidimensional model (called an online analytical processing (OLAP) cube) acting as the main repository and source of data. The OLAP cube simplifies the access and analysis of plant data.The OLAP cube stores data in a specifically-designed way, which allows extraction and analysis to be performed quickly. It is designed to hold large amounts of data on a long-term basis, which could be for the life of the plant. It also performs automatic aggregations over many dimensions on a background process.A major benefit in adopting such a BI solution is that it allows common BA methods to be applied. This is due to both the efficient long-term storage of data and the availability of standard BA tools. BA tools are now able to perform data mining, predictive analytics, forecasting and other machine-learning algorithms. This paper presents the possible use of such advanced data analysis methods in a beneficiation plant.CITATION:Fry, M R, Nassis, T, Louw, P and du Toit, T, 2015. The use of common business intelligence and analytics tools in the operation and optimisation of iron ore process plants, in Proceedings Iron Ore 2015, pp 129–138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A Tawadrous, D S. Preece

Cave mining is of interest to the mining community as it offers a chance to extract large, deep orebodies with low operating costs and high production rates. It allows for extracting large low-grade orebodies, which may not have previously been considered for mining. Cave mining is done either top down (ie sublevel caving) or bottom up (ie block/panel caving). Both approaches rely on gravity, stresses and weakness of the rock to fracture and achieve a controlled collapse.Block caving starts at the base of the orebody. It progresses upward and across through continuous collapse of the roof. To achieve this, a critical hydraulic radius must be exceeded. This is accomplished by blasting drawbells, through which the caved ore passes to the production level. An entire level above the drawbells (undercut level) is excavated to help initiate the cave. The undercut level ensures the connection between drawbells and achievement of the required hydraulic radius.Conventionally, drawbells are generated by drilling and blasting several times from the production level as well as the undercut level. Mucking between each shot is required to generate enough void space for the rock to swell. The need for several blasts necessitates some downtime between each blast. Also, the cost of developing and maintaining the undercut level can constitute up to 35 per cent of the cost of mining the panel.A new blasting technique was developed to create the drawbells in a single blast from the production level. The technique ensures the connection of the drawbell to the neighbouring ones, thus, the critical hydraulic radius is reached and propagation of the cave achieved without the need for the undercut level. The technique has the potential to reduce the capital cost of a block caving operation, increase its feasibility and reduce time to reach the ore and consequently the payback period. This paper presents the modelling of a traditional drawbell excavation process, the philosophy of the developed technique, the modelling of that new design and its implementation.CITATION:Tawadrous, A and Preece, D S, 2015. A novel blasting technique to create drawbells and eliminate the undercut level in block cave mining, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 617–624 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Howard

Following discovery in October 2004, commencement of development in February 2007 and first ore production in mid 2007, the Trident gold deposit, located in the Eastern Goldfields of Western Australia, has now been successfully mined for over three years. Three years of operational history has enabled the performance of the Trident underground mine to be reconciled against the mine plan and strategy proposed for the original feasibility study.The Trident deposit, initially based on two lode systems known as the Eastern Zone and Western Zone, has been continuously drilled, interpreted and re-interpreted over the period and as a result the addition of the Athena, Apollo and Artemis lode systems as well as numerous smaller scale lodes has been realised. The first three years has seen the Trident underground mine quickly move up to its 1 Mtpa design production rate. The mine plan and strategy used in the initial feasibility study and subsequently implemented, required sufficient flexibility to enable modification and optimisation to mine plans as ore zones were further defined. The ability to modify the mining plans has enabled Avoca to achieve its mining targets at Trident. With over 250 000 ounces gold produced to January 2010, the company is well positioned to achieve its ten year vision associated with the Higginsville Gold Project.This paper offers an account of operational experiences whilst providing comparison to assumptions and methodologies used in the original feasibility study. The paper is a sequel to a paper presented at the Tenth Underground Operators’ Conference held in Launceston, Tasmania titled Development Strategy of the Trident Underground Gold Mine.

Mar 21, 2011

By T Atchison

In-pit crushing and conveying (IPCC) systems have come under growing scrutiny as a perceived mitigation to fuel and equipment price fluctuations, labour shortages and the need to move everincreasing volumes of material. Individual vendors and delivery organisations are now offering a sometimes confusing array of systems, particularly for the dig and dump side operations.One system does not suit all operations. This paper seeks to document the factors that should be considered in assessing the suitability of different IPCC systems, with a focus on dig side equipment layouts in particular. These factors include the productivity of the systems, interactions with the drill/blast and bench operation sequence, the ease of relocation, flexibility to changes in the reserve, scalability and compatibility with other elements of the system.

Jul 11, 2011

By G Brudek, P Elestedt

Schalker Eisenh&#252;tte und Maschinenfabrik GmbH, Nordic Minesteel Technologies and Bombardier Transportation have developed an evaluation tool that considers the main cost drivers of the rail, truck and conveyor haulage systems on the market today. In almost every circumstance, the advantages of a haulage solution are clear. A haulage system is outlined that is fully automated, including driverless operation, and that provides increased tonnage, safety and equipment life and reduced maintenance downtime. The haulage system has been implemented by a number of companies, including Codelco, LKAB and Freeport’s Grasberg mine. CITATION:Brudek, G, Elliott, R P and Elestedt, P, 2016. Moving mORE for less, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 535–542 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016