Search Documents

By Simon D. Strauss

The world appetite for minerals in the, third quarter of this century grew at a higher rate than had been anticipated. To illustrate, consider the experience of four, commodities. Excluding the Communist bloc, sometimes referred to as the centrally planned economies, demand for aluminum increased at a compound rate of 8.6% between 1950 and 1975,; copper rose by 4.4%; iron ore by 5.5%; and tin, the laggard in the group, by 2%. Except for tin, the figures are substantially greater than growth rates anticipated in 1950 in the Paley Commission report and other studies. The growth rate was not evenly distributed in geographical areas. Professor Wilfred Malenbaum of the University of Pennsylvania did an interesting study breaking these figures down as among three principal sources of demand -- the United States, other industrialized nations (which he referred to as the "rich lands"), and the developing world (which he referred to as the "poor lands").

Jan 1, 1982

By Blair R. Benner

This paper describes the installation and operation of a Texas Nuclear on-line silica analyzer (NOLA) coupled with a Leeds and Northrup Microtrac particle-size monitor (Microtrac) at U.S. Steel's Minntac taconite concentrator. An automatic sampling system provides the NOLA with samples of final concentrate. After the sample is analyzed for silica by the NOLA, it is pumped to the Microtrac for size and surface area measurement. A sample is analyzed every six minutes, providing the control room with the silica concentration, the percent passing 270, 400, and 500 mesh, and an equivalent Blaine surface area number. When fed a slurry of final concentrate containing between 20 and 70% solids and 5 to 6% silica, the NOLA analysis is within ±0.2% of the wet chemistry silica. The agreement between the Microtrac output and standard screen analyses is ±1.2% at 270 mesh; ±1.5% at 400 mesh, and ±2% at 500 mesh. The poorer disagreement at the finer sizes is mainly due to inaccuracies in screening at 400 and 500 mesh. The agreement between Microtrac surface area a d laboratory Blaine surface area is about 9 ±80 cm 2/g. These instruments provide rapid and reliable feedback information to the concentrator and feed forward information to the agglomerator.

Jan 1, 1984

By C. C. Bailey

THE vendor seeking outside capital for his project has the following potential sources which may be approached; 1--private sources, 2-institutional funds, 3--government agencies, 4--established mining concerns, and 5-public financing.

Jan 7, 1953

By E. A. Gulbransen, K. F. Andrew

Weight loss measurements were made using a sensitive microbalance operating in a high vacuum system. The Langmuir equation was used to Calculate the vapor pressures of the several metals and alloys. Aluminum lowered the vapor pressure of i9,on in a 5.4 Al-94.6 Fe alloy, and of iron and chromium in a 4.8 Al-21.5 Cr-73.7 Fe alloy. The influence of oxide films formed on the alloys on the effective vapor pressures of the alloys was also studied. These studies were used to aid in the inte9,pretation of the high temperature oxidation of alloys based on iron, chromium, and aluminum. RECENT studies on the oxidation of chromium1 and the heat resistant alloy 5 Al-22 Cr-73 Fe showed transitions in the rate of oxidation at 900o and 1050oC respectively. The transition for chromium occurred at a temperature where the rate of evaporation of chromium from oxide-free surfaces equalled the rate of chromium atoms reacting with oxygen. This paper presents new vapor pressure studies on iron, chromium, and the specially prepared alloys 5.4 Al-94.6 Fe, 21.9 Cr-78.1 Fe, and 4.8 Al-21.5 Cr-73.7 Fe. The ternary alloy is similar in basic composition to the patented heat-resistant commercial alloy known as Kanthal. The binary alloys were studied to show the individual effects of aluminum on the vapor pressure of iron and of iron on the vapor pressure of chromium. The purpose of the proposed studies was to test the influence of metal volatility on the oxidation behavior of heat-resistant alloys based on iron, chromium, and aluminum. Since oxide films formed on the metal may limit metal transfer to the surface, the influence of oxide films on metal volatility was also studied. LITERATURE A) Vapor Pressure. The vapor pressure of iron has been studied by Jones, Langmuir, and Mackay,' Dornte and Nrton. Edwards. Johnston. and Ditmar. and McCabe, Hudson, and Paton. Stull and SinkeT have calculated a heat of sublimation at 298° K of 99.83 kcalper g atom. The vapor pressure of chromium has been reported by Bauer and Brunner,' Speiser, Johnston, and Blakburn, Gulbransen and Andrew,'' Vintaikin,o McCabe, Hudson, and Paton, and Kubaschewski and Heymer.12 Good agreement was obtained except for the early work of Bauer and Brunner.' Stull and Sinke7 calculate a heat of sublimation at 298°K of 95.0 kcal per g atom. Vapor pressure measurements on aluminum have been made by Brewer and Searcy,13 Bauer and Brunner,aand Farkas.I4 Stull and Sinke,7 giving Brewer and Seary's' data the most weight, derive a heat of sublimation of 77.5 kcal per g atom at 298 oK. B) Method. Two methods15 are used for measuring the vapor pressure of metals: 1) The Langhuir free evaporation method, and 2) the Knudsen effusion method, In the Langmuir method, used in the present work, the vapor pressure of the metal P is given by the equation: Here M is the molecular weight of the vapor species. T is the absolute temperature. (dw/dt) is the rate of sublimation in g per sq cm per sec and a is the condensation coefficient. a is a measure of the efficiency of condensation of molecules striking the metal surface from the vapor. If condensation results from each collision a is unity. This coefficient has been found to be unity,a, le for metals. These results establish the general validity of the Langmuir free evaporation method as applied to metals. EXPERIMENTAL A) Vacuum Microbalance Method. A modification of the Langmuir free evaporation method was used. Strip specimens were suspended from a sensitive microbalance operating inside of a high vacuum system. For alloys, microbalance methods17 must be used on large area samples at relatively low temperatures to minimize composition changes. The

Jan 1, 1962

By J. Chipman, N. J. Grant, H. L. Bishop

In a recent review1 of the iron-oxide activity of simple open-hearth type slags containing lime, magnesia, silica, and iron oxide, it was established that activity values were lacking in the range of slag composition most interesting to open-hearth operators. That is, laboratory experimental results were not available for simple slag compositions having basicity ratios ranging from about 1.5 to 4.0 and iron-oxide concentrations ranging from about 10 to 30 pct. However, in order to estimate iron-oxide activities for the range of slag compositions of interest to open-hearth operators, activity values were calculated using ionic concepts of slags by following the treatment of Flood and Grjotheim.2 A study of these data indicated that the desired slag compositions were probably not obtained due to the limited solubility of the basic constituents lime and magnesia. Thus, it was decided to make additional heats equilibrating molten carbon-free iron with slags containing MnO, P2O5, and A12O3 in percentages commonly found in open-hearth refining slags, and to examine the liquid slag field over a greater composition range than that of the simple slags studied previously. The ranges of the constituents used in the present study are summarized as follows: Metal Pct 0 0.070-0.201 PctMn 0.005-0.142 Slag Pet CaO 24.45-41.90 Pct MgO 3.23- 9.21 Pct MnO 1.13- 9.62 Pct FeO 20.08-48.7 Pet Fe2o3 2.23-10.14 Pct SiO, 3.51-28.50 Pct P2O5 0.23- 3.65 Pct A12O3 0.43- 3.38 The experimental procedure consisted of equilibrating the slag and metal in an induction furnace provided with a carbon-arc slag heater as described previously by Winkler and chipman.3 The data obtained were used to establish both the iron-oxide activity values and the activity coefficients for FeO and MnO in the open-hearth type slags. RESULTS AND DISCUSSION I) Iron-Oxide Activity of Open-Hearth Type Slags—The iron-oxide activities of various iron-oxide contents of the open-hearth type slags, as calculated from the oxygen content of the metal by the method of Taylor and Chipman, 4 are plotted against the molar ratio of bases to acids in Fig. 1. The data represent slag-metal studies carried out in the temperature range 1530" to 1700°C. For the purpose of this study, the constituents CaO, MgO, and MnO are assumed equal on a molar basis in their effect on the iron-oxide activity; and, PO2,5 is calculated as an equivalent to SiO2 and A12O3 on a molar basis. The total iron content of the slag is calculated to FeO and is represented by the symbol (FeO) The points presented in Fig. 1 represent the results of this investigation for iron-oxide slags containing between 1 and 8 mol pct MnO and less than about 2 mol pct each of A12o3 and PO2,5 The curved lines shown in Fig. 1 represent the results of the summary1 of the iron-oxide activities of simple slags of the system (CaO + MgO) - SiOz - (FeO),. The solid portions of the curved lines represent experimental data, and the broken portions represent iron-oxide activities calculated from ionic concepts of slags. The iron-oxide values of the open-hearth type slags of this study are in good agreement with the values of the simple iron-oxide slag system. Only a slight modification is indicated. The results of this study suggest that the line for 20 mol pct (FeO), should be lowered slightly in the basicity range 1.5 to about 3.

Jan 1, 1959

By P. R. Sahm, T. V. Pruss, D. A. Gandolfo

Cb 3 Sn powders were hot-pressed to estahlish densi-fication conditions and assess the possible use of such compacts in multiphase structures with ceramic or magnetic inclusions. Superconducting transition temperatures, Tc, were measured as a function of powder particle size, pressing temperature, and second-phase admixtures. The highest transition temperatures were found in coarse powder (5 to 500 u) compacts and were only weakly depended on pressing temperatures up to 1200°C. Fine powders (below 5 p), however, both single-phase CbsSn and Cb3 Sn-composites, showed a stronger dependence on hot-pressing temperatures. While Al2 O3 phase admixtures did not affect T, much more, a Pronounced T, degradation was observed upon the addition of ferrimagnetic Fe2 Mno. 5 Zno.5 O4 powders. Likewise, critical current densities, Jc, at 4.2° K were lowered appreciably in the ferrite doped samples, whereas the neutral A1203 inclusiow gave slightly improved Jc values. MULTIPHASE structures in electronically active materials have recently gained in interest as pointed out by Galasso in a review article.' In superconductors the most widely reported group are eutectic alloys which have been mostly investigated with respect to the proximity effect.2"4 In addition, "artificial eu-tectics", for example in the form of mercury-vycor glass sponge5 or fine niobium wires imbedded in a copper matrix,= have been prepared to attain higher critical fields and critical current densities. The idea was to enhance flux pinning phenomena by second-phase inclusions or ho1es. 7 Flux pinning should also be possible by the introduction of insulator inclusions into a superconducting matrix. Ceramic-metal combinations are most easily produced by hot pressing (= pressure sintering), as it permits an almost unlimited selection of material combinations. Cb 3 Sn has been prepared by vapor phase growths or in the form of thin films. Large compacts must be sintered,1° however, and normally present difficulties. At temperatures below 1350°C insufficient densities are obtained and at higher temperatures the loss of tin due to dissociation upsets the stoichiometry. Hot pressing is a natural approach to circumvent the problems, since one can obtain satisfactory densities despite low sintering temperatures. This work was mostly concerned with establishing conditions to hot press Cb3 Sn and Cb3 Sn multiphase structures (= composites), because no data are presently available, and to evaluate these with respect to their transition temperatures. However, a few measurements on critical current densities were also carried out, in particular to assess the value of ferrimagnetic inclusions. I) EXPERIMENTAL PROCEDURE The experimental procedure involved the preparation of feed material and powders, hot pressing, and evaluation of the resulting ingots. As no attempts were made to synthesize Cb3Sn from the elements during hot pressing, feed material had to be produced. For this purpose, a stoichiometric Cb-Sn powder mixture was compacted into a 3-cm-diam ingot (80,000 psi) and then inserted into a quartz tube and evacuated. Rf heating was employed. Above the tin melting point (230°C) liquid tin was forced out of the ingot, but was pulled back by capillary action after approximately 0.5 hr of continuous pumping at 700°C. Thus, it appears that evacuation at this temperature caused desorption of impurity gas creating wetting surfaces which, later on, favored alloying at relatively low temperatures. After a presintering period of 17 hr at 800°C, the quartz tube was tipped off and sealed into another such larger-diameter tube which, in turn, was connected to a pump system. This configuration permitted a temperature treatment at 1400°C, carried out for 65 hr, without collapsing of the glass walls or unfavorable chemical interaction of Cb3Sn with the quartz. The resulting material was

Jan 1, 1969

By Peter M. Fozzard

The San Bartolomt silver deposit was discovered by a United Nations team of geologists working with a counter- part team of staff of the Ecuadorian Government's General Directorate of Geology and Mines (DGGM). The Phase I project over five areas of operation during which this discovery was made was financed through a United Nations Development Program contribution of $860,000 and an Ecuadorian Government participation of about $680,000 equivalent. Existence of mineralization at San Bartolomé was first recognized in 1966 when a reconnaissance geochemical stream-sediment program was carried out over a 10 500 km2 (4,054 sq mile) area centered around the city of Cuenca in southern Ecuador. Over the course of this project more than 10,000 samples of stream-sediment, soil, and rock materials were collected. Average costs per sample were $10.00, as follows: collection, $5; sample preparation, $1.60; assay work, $3.40. Initially in the program (1965-1966) sediments were collected along all motorable roads and tracks. Routine analyses, originally by colorimetry and later by AAS, were for Cu, Pb, Zn and occasionally As, Ni, and Co. Discovery geochemical samples from the San Bartolomé drainage area were among the first to be taken in 1965. As luck would have it, the road along which this traverse was taken passes only some 100 m (328 ft) downstream from the mineralized suboutcrop. The relevant two streams sampled are of inconsequential size, some 1 m (3.3 ft) in width, with a limited flow volume throughout the year. Original anomalies were recognized through cold-extractable Cu/Zn analyses. The pH of all river waters was also recorded at sample sites. Resampling the discovery sediments when AAS became available showed total extractable values of between 150 ppm-300 ppm Zn, 550 ppm Pb, and 10 ppm Ag. In 1967 the first followup was by rough-and-ready means. Dithizone field-kits (THM) were used to rapidly test soils from the surrounding area. The area has no outcrop. This work allowed the definition of an area of interest of some 2 km (1.2 miles) x 500 m (1640 ft). Six approximately 1 km (0.6 mile) to 1.5 km (0.9 miles) lines spaced at approximate 250 m (820 ft) intervals were established and used for IP surveys and soil sampling at 50 m (164 ft) intervals. Where one of the lines crossed the westernmost geochemical discovery creek a first-priority geophysical anomaly coincided with a major Zn/Pb (and later Ag) soil anomaly. A pit was sunk and encountered mineralized vein material at a depth of 1.5 m (5 ft). This lucky glory hole confirmed the geochemical discovery and prompted systematic followup. Immediately, costeaning of the west bank of the discovery creek, the Quebrada Ocashuaico, was carried out and exposed weathered and leached mineralization. Nearly 100 mineralized veinlets ranging in thickness from 0.5 cm (0.2 in.) to 8 cm (3 in.) were exposed across the 180 m (59 1 ft) costean. Sixty mineralized veinlets were determined over a 90 m (295 ft) wide zone. Sampling delineated minable widths averaging between 0.16 and 0.31 kg/t (5 and 10 oz per st) Ag with associated copper (very sporadic) lead and zinc. Over the period 1968- 1972 a considerable amount of detailed work was completed: detailed IP, EM Turam, magnetic and mise-a-la-masse geophysics, very detailed soil- sampling, trenching, drilling and glory-hole drifting, and cross-cutting. Numerous problems were encountered: the area was found to be a most difficult geoelectrical target; zero outcrop; pyrite (nonargentiferous zones) associated with faulting; mineralized groundwater; extensive clay development; loss of diamond drill-core, and no two-dimensional surface information. As the program developed the complexity of the structure was slowly unravelled, using a degree of good guesswork. Apart from photogeological and ground geological mapping at various scales, the following

Jan 1, 1985

By M. J. Hordon

Measurements of the 103 yield stress of ordered and disordered poly crystalline Cu ,Au were related to the ordered antiphase domain size determined by resistivity measurements. For undeformed material, a yield stress maximum wa obtained at a critical domain diameter of about 40A. Plastic deformation resulted in a marked increase in the yield stress and electrical resistivity of the ordered alloy compared to the disordered, the strain hardening rate increasing regularly with initial antiphase domain size. Order hardening was accompanied by a sharp reduction in size of the initially large domains. It has been observed that the yield stress of ordered and partially ordered Cu3Au alloy varies sensitively with antiphase domain size aid degree of order.ly2 In addition, ordering of the lattice leads to a marked increase in the strain hardening rate (order hardening) as compared to the rate for the disordered alloy. In the present investigation, changes in the electrical resistivity and yield stress of ordered polycrystalline Cudu with varying initial domain diameters were measured after tensile plastic deformation in order to examine the effect of cold work on the antiphase domain size. EXPERIMENTAL PROCEDURE Au-Cu alloy of 99.99 pct purity analyzing 50.85 wt pct Au-balance copper was obtained from the Handy-Harmon Co., N. Y., in the form of 0.061 in. diam drawn wire. Wire specimens 3 in. in length were given the following annealing treatment in nitrogen: 500" for 72 hr, 820" for 15 hr, and 450" for 5 hr, followed by a water quench. The annealing sequence resulted in a completely disordered structure with a grain size of about 0.2 mm. The disordered specimens were then reannealed at 360' in nitrogen for periods varying from 10 min to 150 hr followed by quenching to produce ordered structures with varying domain sizes. The degree of ordering and variation of domain size was followed by electrical resistivity measurements made at room temperature using a low resistance precision Kelvin double bridge apparatus. The specimen resistance was determined over a length of 4.0 cm between two brass knife-edge contacts while the specimen was immersed in an oil bath to minimize temperature variations. In addition, the current flow in the circuit was minimized by a current pulse technique in balancing the bridge in order to avoid heating the specimen. Using a sensitive galvanometer to detect the bridge null, the accuracy of the resistance measurement Wire specimens were plastically strained in tension with an Instron tensile unit at strain rates in the range 5 x 10"5 sec-' to 2 x 10"4 sec-'. Stress and extension data were fed into the Instron chart drive amplifier to obtain the actual stress-elongation curve from which the yield stress at 10"3 strain was determined. The maximum resolution of the apparatus was approximately 50 psi stress and 3 x 104 strain. At various plastic strain levels, deformation was interrupted and the electrical resistivity determined after removing the stress. RESULTS AND DISCUSSION 1) Yield Strength of Ordered Cudu. In order to determine the effect of the ordered antiphase domains on the initial yield stress, specimens were prepared with varying domain sizes ranging from zero for 5 completely disordered structure to about lo5A for a completely ordered structure by suitable annealing treatment. Domain sizes were estimated by comparing room temperature electrical resistivity data with the original data of Jones and sykes3 as modified by rdle.' In agreement with previous work, the resistivity varied sensitively with domain diameter and degree of order, decreasing from approximately 11.6 x l0- ohm-cm for the disordered structure to about 5.9 x l0- ohm-cm for ordered domains above 10"3 cm in diameter. Fig. 1 shows the change of the 103 yield stress with ordered domain size. It is evident that the maximum

Jan 1, 1963

By B. M. Larsen, K. Heindlhofer

Jan 1, 1945

By H. R. Spedden

As part of its broad program of educational assistance-including grants, fellowships, and scholarships -Kennecott Copper Corp. offers summer employment opportunities for college students at each of its operations. Originally, summer job programs were intended primarily to help students defray their educational expenses. But as the nation's economy expanded with increased production and a growing demand for well-trained engineers, summer employment became an important means to help qualify future professionals and fill industry's need for them. Both the employer and the student thus derive benefits from such training.

Jan 6, 1967

By Hans Lundberg

AFTER the war years, great activity has been shown in geophysical exploration for ore. The appreciation by mining and government geologists of geophysical techniques and results is largely responsible for the popularity of these methods. In Canada, plans are being made to study, by geophysical methods, the structure of a portion of the Pre-Cambrian shield in the hope that such studies will not only give a clearer picture of the geology, but will be of direct aid to the mining companies when selecting areas for detailed prospecting. Although geophysics thus has become more popular, some engineers are still reluctant to employ the methods to their full extent. Allotted funds are often rather low, so that the least expensive

Jan 1, 1947

By D. W. Brunton

Discussion of the paper of D. W. Brunton, presented at the Spokane meeting, September, 1909, and published in Bulletin No. 33, September, 1909, pp. 837 to 855. WILLIAM' KENT, New York, N. Y.:-The Institute may congratulate itself on the opportunity of reading the splendid address of President Brunton. It is au admirable summary of the progress that has been made in the mining and metallurgical arts in recent years. The paper rightly give's the chief credit for this progress to the aid which has been rendered to these arts by the advances in mechanics, chemistry, and electricity. It is notable that most of the headings in Mr. Brunton's address refer to the work of the mechanical engineer, the electrical engineer, and the chemist, rather than to that of the specialist in mining-operations. It seems that. the most successful mining engineer of the present day is the one who makes the most intelligent application of the inventions and designs of engineers and others who are not directly engaged in mining. A tabulation' of the headings of the address, grouped as below, shows this most clearly. Work of the Mechanical Engineer-Rock-drills, hoisting-machinery, tramming, pumping, ventilation, dredging, sampling, concentration, briquetting, fume-recovery. Work of the Electrical Engineer-Electric machinery for hoisting, pumping, tramming, lighting and signaling, electric . transmission, electric smelting. Work of the Chemist and Metallurgist-Explosives, chlorination, cyanidation, roasting, lead-smelting, and copper-smelting. Work of the Geologist-Economic geology. Work of the Mining Engineer-Mine-mapping, surface-mining, timbering, tunneling; and planning and supervision of the work in general. The mining engineer of the present day, who is in responsible charge of a large plant, finds his chief work not in doing

Jan 1, 1910

By C. G., Fink

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution.

Jan 1, 1950

By R. F. Domagala, M. Hansen, D. J. McPherson

On the basis of metallographic analysis, incipient melting data, thermal analysis work, and X-ray diffraction, phase relationships in the 0 to 50 atomic pct alloy content were carefully resolved. Phase relationships in the higher alloy content regions were outlined. A single intermediate phase, peritectically formed, of the form ZrX2 was established in each system. A eutectic and a eutectoid were found in the zirconium-rich region of both systems. Appreciable solubility of molybdenum and wolfram was found in ß zirconium, but only a slight solubility in a zirconium. PREVIOUS work on these systems was limited to X-ray investigations of the intermediate phases1, 2 and preliminary surveys of the zirconium-rich alloys." The diagrams presented were determined principally by metallographic, thermal analysis, and incipient melting techniques. In accordance with the Atomic Energy Commission contract requirements, phase relationships up to 50 atomic pct molybdenum or wolfram were carefully resolved, while only a limited amount of work was done to outline the 50 to 100 atomic pct alloy region. A description and analysis of the metals used in the preparation of alloys for this study are included in Table I. A "low-hafnium" zirconium crystal bar, produced by the decomposition of a volatile iodide onto a hot filament, was employed for these studies. Westinghouse "Grade 3" crystal bar was used for all alloys. The zirconium, as received, was coated with corrosion product from a standard autoclave test by which its grade designation is determined. This was removed by a sand-blasting and HF-HNO, pickling technique developed by the Atomic Energy Commission. The bars were cold rolled to approximately 1/32 in. sheet, pickled for iron removal, sheared to 1/4 in. squares, washed with acetone, and stored for furnace charge. Molybdenum sheet. 0.003 in. thick, 0.001 to 0.005 in. wolfram wire, and M in. wolfram rod crushed to granular form, from Fansteel Metallurgical Corp., were used as alloying stock. Melting Procedure A nonconsumable electrode arc furnace identical to that described in detail by Hansen et al.4 was used. The source of power for melting Zr-Mo alloys was a 400 amp dc welding generator, while a 900 amp dc generator was used for preparing Zr-W alloys. Electrode tips of the same material as the alloy addition were employed in both systems, i.e., molybdenum tips were used for Zr-Mo alloys, and wolfram tips for Zr-W alloys. This precluded any possible electrode contamination during arc melting. Ingots of 20 to 30 g of Zr-Mo alloys were melted under high purity helium in the cavity of a copper block insert in a spun copper crucible. Homogeneity was insured by remelting all ingots four to six times without opening the furnace. Due to the large difference between the melting points of wolfram and zirconium, direct melting of the charged metals as above generally yielded ingots containing unmelted wolfram particles. This was overcome, after many variations in technique, by melting a pure wolfram charge at high power levels (700 to 900 amp) and slowly adding zirconium to form a master alloy. Such master alloys were sectioned and remelted several times, then crushed to serve as melting stock for alloys of lower wolfram content. Master alloys containing 26, 50, 52, 70, and

Jan 1, 1954

By C. Land, R. Hultgren

Heat contents of four Cr-Ni alloys were determined in a diphenyl ethev calorimeter. Aside from ferromagnetic effects, Kopp's law of additivity of heat capacities is approximately fol-lowed, in disagreement with earlier results of A. W. Foster. In 1934 Foster1 reported heat-capacity measurements of dilute solutions of chromium in nickel, primarily as a study of the effect of alloying on the ferromagnetic Curie temperature. He found that, apart from the Curie temperature effect, the general level of heat capacities was reduced 10 pct by the addition of 1 pct Cr; 20 pct by the addition of 2 pct Cr. His measurements of pure nickel essentially agreed with accepted values. These results indicate that small amounts of dissolved chromium cause an increase in the Debye temperature of nickel, presupposing a change of frequency of interatomic bonding vibrations which is much larger than should be expected. If Foster's results were verified, therefore, they would have important implications for bonding theory. The only other heat-capacity measurements in this system seem to be those of Taylor and Hinton,' who studied anomalies which they attributed to super-lattice formation at 25 at. pct Cr. At temperatures above the anomaly, Taylor and Hinton found heat capacities at this composition were quite normal, approximately obeying Kopp's law of additivity. EXPERIMENTAL WORK In order to verify or disprove the remarkable results of Foster, the heat contents of four dilute solid solutions of chromiunn in nickel were measured in a diphenyl ether calorimeter. This instrument, described elsewhere,, operates on the principle of the Bunsen ice calorimeter, but uses diphenyl ether as the working substance. Diphenyl ether melts at the convenient temperature of 26.S°C and supplies a more sensitive measure of heat than ice. The hot sample, in an atmosphere of argon, is dropped from a furnace at a measured temperature into a chamber which is surrounded by a mixture of solid and liquid diphenyl ether. The heat from the hot specimen melts some of the solid without chang- ing the temperature of the calorimeter. The amount of solid melted, and therefore the number of calories released by the specimen, is measured from the increase of volume of the mixture, which pushes mercury down a graduated capillary tube. The apparatus has been standardized against the known heat content of pure platinum. Heat loss during the dropping of the specimen was estimated by comparing the heat content of an empty platinum capsule with a solid platinum ball of the same radius and degree of polish of the surface. Repeated tests demonstrate the precision of measurement to be closer than *0.3 pct. Smoothed experimental results are listed in Table I. The tabulated values for pure nickel are taken from kelley, several measurements were made which agreed closely with this tabulation. For chromium, however, no similar agreement was found. The values tabulated were taken from a thorough study of chromium with the diphenyl ether calorimeter which will be published elsewhere.= Suitable plots of the data showed the expected ferromagnetic anomalies in the low-chromium alloys, while the 11 pct alloy shows no ferromagnetic anomaly, but a different, small anomaly below 900°K. This is perhaps the same anomaly found in CrNi, which was once attributed to superlattice formation,' but is probably due to some other cause, such as antifer-

Jan 1, 1960

By Paul L. Russell

THIS is a progress report of an experiment being undertaken in cooperation with the Bethlehem Steel Corp., the Crucible Steel Co., and the Rock Bit Sales and Service Co., involving heat treatment of the shank ends of drill steel. This experiment is being conducted by the U. S. Bureau of Mines in its experimental mine, Mining Research Branch, Bluemont, Va. The purpose of the experiment is to determine the effect of an increase in the time the steel soaks in the furnace during the hardening heat. It has been thought that increasing this time produces a soft zone below the lugs resulting in a metallurgical notch that causes early failure. Each of the steel companies furnished enough 11/4 - in. straight carbon, hollow, round steel to make up 10 sets of drill steel, in each instance the steel bars were from the same heat. These sets of drill steel, consisting of 2-ft, 4-ft, 6-ft, and 8-ft lengths were fabricated by the Rock Bit Sales and Service Co. Special attention was given to the forging of the steel to produce the best rods possible. The heat treatment of all thread ends was identical and followed the best practice. The heat treatment of the shank ends of five sets of steel from each company produced a soft zone 2 to 4 in. in front of the lugs. It was decided that possibly the best way to obtain this effect was not to overlap the hardening heat but to let the steel soak for an additional 30 min before quenching. Therefore the only variable in the test steels is the length of time the shank ends were in the furnace. The remaining drill steel shanks were treated as follows: Heat treatment in pyrometer-controlled furnace at 1550°F. Quenching oil at 105°F to 125°F temperature. Areas for heat treatment were; shanks, 11 in.; threads, 9 in. Time at heat, standard practice, 20 min for 11/4-in. steel. Actual drilling tests were made in greenstone, (a metamorphosed basaltic rock), and in epidosite. Greenstone has a specific gravity of 2.96 and a compressive strength of 44,200 psi. Epidosite has a specific gravity of 3.26 and a compressive strength of 63,100 psi. All drilling tests were made using a 31/2-in. column-mounted, automatic feed drifter, with a controlled air pressure of 90 psi at the throttle. Tungsten-carbide bits of 2 in. diameter were used for all drilling. Contrary to expectations the drill steels that were allowed to soak for the additional 30 min before quenching performed better than the steels that were heat treated according to standard practice. This performance, as shown in Table I, was especially noticeable in the drilling of epidosite. The "longheat" drill steels furnished by Company "A" drilled 154 pct more minutes than the "standard-heat" steel. Expressed in feet, the "long-heat" steel drilled 114.60 ft more before failure than the "standard-heat" steel. The "long-heat" steel furnished by Company "B" drilled 37 pet more minutes or 60.39 ft more before failure than the "standard-heat" drill steel. The effect of the long heat treatment was not as evident when the steels were drilling in greenstone (Table II). In greenstone, the increase in minutes drilled by the "long-heat" steel over the "standard-heat" steel was 47 pet and 1 pet, respectively, for Companies "A" and "B."

Jan 1, 1952

By R. D. Carpenter, R. R. Smith, E. E. Sougstad

The Union Carbide Nuclear Co., in treating low-grade tungsten and molybdenum-copper ores at the Pine Creek mill near Bishop, Calif., employs flotation for the initial extraction of the valuable mineral constituents. These minerals consist of scheelite, molybdenite, and several of the copper sulfides including chalcopyrite, bornite, and possibly chalcocite. They occur in a gangue consisting mainly of quartz, pyroxene, and garnet, with minor amounts of calcite and fluorite. This assemblage of minerals presents an unusual grinding problem because of their diverse physical characteristics. Feed for the circuit is prepared from -6-in. ore by screening on a rod deck screen to remove the -5/8 - in. material. The+5/8-in. fraction is crushed in open circuit with a 5 1/2-ft Symons shorthead crusher operated at a closed- side setting of approximately 3/8 in. The screen undersize and the conecrusher discharge are then combined to constitute the feed to the grinding circuit. The ore is ground in 6 by 5-ft grate discharge ball mills operated in closed circuit with 54-in. spiral classifiers. The classifier overflow goes directly to the flotation section of the plant. Studies of the flotation circuits have shown that the maximum recovery of the tungsten, molybdenum, and copper minerals occurs in the particle-sue range from 100 mesh to approximately 400 mesh. Further, practice has shown that the ore minerals are effectively reduced to this size range if the total ore is ground to -48 mesh. The general objective of the grinding circuit then is to reduce the feed to -48 mesh with the production of a minimum amount of slimes. The purpose of this investigation was to ascertain how well the grinding circuit was carrying out this objective. The method used was to sample the various products in the grinding section, size these products accurately, and analyze the resulting sue distributions. SAMPLE PREPARATION AND SIZING TECHNIQUES Representative samples of the different grinding circuit products, namely, new feed to the ball mill, ball mill discharge, classifier overflow, and classifier return, were taken over a 24-hr period. The samples were then dried without being filtered to avoid loss of slimes. The percentages of solids in the different products were the following: new ball-mill feed, 95%; ball mill discharge, 82%; classifier overflow, 52%; and classifier return, 84% solids. Particle sizes were determined on each product by wet-screening an

Jan 1, 1962

By A. G. Buyers, J. Chilton, W. E. McKee

STUDIES in the high-temperature separations chemistry of thorium-uranium fuels are complicated by the corrosive nature of these molten metal systems at 1700°C. Separations research pointed toward the removal of fission products from irradiated alloys has included a frozen salt-bed technique which minimizes container reaction with molten metal. The procedure consists of high-frequency induction melting of the metal sample which is supported by a vertical column of unmelted salt. The molten alloy melts its immediate salt environment and as it slowly falls down through the column, many of the fission-product poisons are transferred into the fused salt environment. The molten salt-metal zone is encompassed at all times by unmelted salt, preventing container contact. EXPERIMENTAL Experimental methods were separated into three parts: salt-bed preparation, melting, and analytical evaluation. A) Bed Preparation—The procedure for casting calcium-fluoride briquettes was to compress the powdered salt at 5,000 to 10,000 psi and place this compact in a graphite crucible. This assembly was inserted into a vacuum system and surrounded by an alumina crucible as well as molybdenum, tantalum, or stainless-steel foil thermal-radiation shields. The pressure was reduced and the crucible heated under vacuum to about 800°C with the fore pump operating. Argon was then admitted to about 0.8 atm and heating continued until the CaF2 had melted 5 min at the melting point seemed satisfactory). Apparatus used included a 1-in. graphite crucible with 1/8-in. walls, 1-in. ID in a 2-in. induction coil, and a 6-kw Ajax high-frequency converter. B) Melting—Calcium-fluoride briquettes, 1 in. in diam and 1/2 to 1 in. thick, were prepared and vertically stacked to obtain the desired column length. An irradiated alloy sample (nut = 10") was placed on top of the salt column and the assembly was connected to the vacuum system. After evacuation of 5 to 10 , purified argon was admitted and the system flushed twice. The final argon pressure was about 0.8 atm. The sample was heated by induction at a power of about 6.5 kw. It then melted its way down through the salt and freely dropped into a small alumina crucible. The molten metal is followed during its downward course by the induction coil which is mounted upon a power-driven machine-threaded shaft. Experimental conditions used in the foregoing work

Jan 1, 1960

By S. S. Nosseir

INTRODUCTION General Quebec Cartier Mining Co. (QCM) , Canadian subsidiary of U . S. Steel Corporation, operates two iron ore concentrators at the North Shore of Quebec, Canada. In its own operation at Mount-Wright, over 45 million tons per year of crude ore are ground, fully autogenous in six 32' x 11-1/2 Dominion Engineering mills. At Fire Lake/Lac Jeannine operation, property of Sidbec Normines Incorporated (SNI), over 11 million tons per year of crude ore are now ground, fully autogenous, in twelve 18' x 5' Hardinge mills. The Lac Jeannine concentrator was originally constructed by Q.C.M. in 1960 and. was since operated, in beneficiating the Lac Jeannine ore deposit until fully depleted in 1977, at an annual capacity of 18 million tons of crude per year. In 1976, the new company, Sidbec Normines, was incorporated by Sidbec Corporation, British Steel Corporation and Quebec Cartier Mining Co., in proportional holding of approximately 51 to 41 to 8 percent respectively. Since the acquisition of the Fire Lake ore deposit and Jeannine concentrator by the new company, QCM has continued managing the mine and concentrator operaions for S idbec Normines Inc . Flow-Sheet Design Jeannine concentrator comprises twelve identical mill lines grinding the ROM from 8" top size to 14 mesh nominal size range. Driven by 600 H.P. motor at 13.4 RPM corresponding to 73% critical speed, each mill is operated in a closed circuit with two 5' x 12' vibrating screens dressed with 2.5 x 25 mm slot opening cloth. The ground product or screen undersize at an average grade of 33.4% Fe is beneficiated by gravity separation to produce 66.5% Fe concentrate grade at 42.7% weight recovery. At the rougher stage, each mill line con-tains 128 Humphrey 13- 1/2" pitch spirals which produce a final tailing, middling and concentrate products. The rougher concentrate - so produced - is classified by 64 Humphrey pocket sizers into an underflow, which is a final concentrate product and an overflow which is further upgraded by 64 cleaner spirals. The cleaner concentrate together with the pocket sizer 's underflow are dewatered on a 13'[6] horizontal filter. The rougher middling together with the cleaner tailing are recycled in a closed circuit with the spirals. The rougher tailing after dewatering by hydrocyclones is disposed of by a

Jan 1, 1982

By N. J. Grant, K. M. Zwilsky, J. T. Blucher

DISPERSION strengthening has been studied in a number of metal-metal oxide systems. To date those pure metals available as fine particles (less than about 5 p) have received most of the attention whereas solid solution alloys, generally unavailable as fine powders, have not been examined in detail. The present work was undertaken as a preliminary study to evaluate combined effects of solid solution and dispersion strengthening. The technique used was that of dry mixing of elemental powders with the oxide, followed by a diffusion treatment to obtain the solid solution. The average particle size of the powders used was: Ni, 3.2 p (1nco B); Mo, 1.3 p (Fansteel Metallurgical Corp.); and y alumina, 0.027 \i (G. L. Cabot, Inc.). The particle size of the metal powders was determined by Fisher subsieve measurements while the size of the alumina was calculated from a surface area determination. Prior diffusion studies on small compacts pressed from mixtures of nickel and molybdenum powders with and without 7.5 vol pct A1203 indicated that diffusion was complete after sintering for 100 hr at 1800" , or 50 hr at 2250", or 20 hr at 2550° F. The progress of diffusion was followed by microstructural examination and micro-hardness measurements. Two observations made during the diffusion experiments were: 1) That diffusion proceeded faster in the presence of alumina, confirming similar findings by Seith and Loepman on "SAP'';4 2) That diffusion at temperatures above 1800°F resulted in coarsening of the alumina in agreement with results of other authors reporting on the growth of alumina in nickel above 1800"F. Similar experiments in the Ni-Cr system using 6 and 20 p Cr powders of 0.7 and 0.025 pct 0, respectively, did not result in significant solid solution formation even after long time exposures at 2550° F. It must be concluded that chromium oxide films around individual particles interfere with normal diffusion. A nickel alloy containing 5 wt pct Mo and 7.5 vol pct alumina was fabricated by dry mixing of powders, isostatically compacting at 30,000 psi, diffusing for 120 hr in dry hydrogen at 1800" F, and extruding at 1950"~ with a 30 to 1 reduction of area ratio. The resulting structure, presented in Fig. 1

Jan 1, 1963