Search Documents

By B. F. Koch

COPPER reverberatories develop large amounts of exit gases of a temperature in the neighborhood of 2000°F. The gases are not only of a noxious nature but must usually be disposed of at considerable heights above the yard level by a stack. Handling these gases at the temperature mentioned would require rather expensive construction of conveying flues and stack. Moreover, wasting such amounts of heat is certainly most uneconomical. Numerous investigations have indicated that waste heat boilers of the water-tube type are the most practical and economical means for utilizing that heat although the gases are heavily laden with rock dust and copper-bearing slag, which upon cooling form hard deposits on the surfaces of dampers or heat absorbing elements placed in the gas stream. Avoiding Slag and Dust Deposits Based largely on the experience of the paper industry in burning black liquor, a waste heat boiler design was developed a few years ago, providing not only extensive water-wall surfaces for cooling the gases below the fusing point of the slag but also settling out, as far as possible, the solidified particles of slag by creating low gas velocity. Matter carried in a stream of gases or air has a tendency to maintain its original direction upon a change in the direction of the flow of the conveying medium. Reverberatory waste heat boilers installed at Hurley and Morenci endeavored to utilize that tendency for the elimination of slagging particles at predetermined places and before they would strike the tube banks of the boilers. Both installations were successful in minimizing the slagging of boiler tubes and thereby minimizing the need for hand lancing. However, the low draft carried at the up-take of the reverberatory furnaces resulted in a positive pressure in the upper part of the furnace of the waste heat boilers, causing the emission of gases from lancing doors and making more difficult the already unwelcome work of cleaning the boilers by handlancing. Attempting to correct this nuisance as much as possible, the overall height of the Chuquicamata waste heat boilers has been reduced to the minimum considered necessary to obtain proper water circulation in furnace walls. Moreover, it is attempted to solidify slag and dust particles by providing large amounts of water-cooled surfaces before the gas stream reaches super-heater and convection banks of the boilers. The furnaces have been made as deep as an economical and practical arrangement of headers for water

Jan 1, 1952

By T. M. Chance

THE first bituminous coal cleaning-plant to use the sand-flotation process1 was placed in operation on Oct. 1, 1925, at the tipple of the East Broad Top Railroad & Coal Co., at Mt. Union, Pa. The general principles governing the design of plants of this type and typical operating results of anthracite sand-flotation units have been previously outlined.2 I will, therefore, confine myself to a description of this particular plant and to some of the elements of design it incorporates. THE ORIGINAL MT. UNION TIPPLE The plant was installed to transfer coal from steel narrow-gage cars of 60,000 and 70,000 lbs. capacity to standard-gage equipment. The coal was hauled some 30 miles from the East Broad Top field. This coal, mined by the Rockhill Coal & Iron Co. and other operators, is a low-volatile slow-coking coal with- ash of high-fusion point. It is normally a high-grade coal that does not contain an excessive amount of free impurities, but it requires careful handling to secure a fair domestic yield, and, naturally, the need for narrow-gage transshipment increases the difficulty of the problem. The narrow-gage cars were discharged into an 8-car track hopper equipped with two feeders passing the coal to two 42-in. apron intake conveyors. Twin units were installed throughout in this original plant, two lump-and-egg shaking screens, two lump picking-tables, two egg picking-tables and two stoker conveyors. The stoker coal was loaded without cleaning. The loading tracks and booms were in duplicate and with the layout as originally installed either unit could be run independently, each unit shipping a different class of coal or both units making the same product.

Jan 2, 1926

By E. C. Lee

The safety of mine workers has received more attention from both State and Federal law-making bodies than any other industry, a fact that shows clearly the hazardous nature of the industry. The last, but by no means the least, of the measures adopted for the protection of mine workers, is workmen's compensation legislation. This is proving to be a powerful instrument for greater safety in the industries, from the fact that special stress is laid not on how the accident happened or who may have been responsible for it, but on how badly the employee is hurt by it. The injured person does not have to employ lawyers to prove his case, because- the mere fact of his employment is proof of his right to compensation. The immediate effect of such legislation is the certainty confronting the mine operator that he must. pay out large sums for every accident, regardless of its cause, thus adding materially to the cost of the production of his coal. his fact furnished to the operator the strongest incentive to reduce the causes of accidents; not that the operator has ever lacked reasonable consideration for the welfare of his employees and a proper humane interest in their safety, but his engrossmentin earning his daily livelihood has been so great that he has not felt that he had the time to devote to the safety of the operation. This time he must now find because of the actual cash value of the prevention of accidents in his mines. This agency alone proved inadequate to bring about a material improvement because operators have always been willing enough to improve safety conditions when possible to do so within reasonable limits of their financial ability. The requirement in the Workmen's Compensation Laws of several of the States, that the mine operator shall insure as a guarantee of his ability to meet his compensation obligations, has furnished the needed incentive, moral and financial, necessary to the prompt and effective dissemination of a more general knowledge of the causes and

Jan 1, 1918

By Rossiter W. Raymond

BY the courtesy of Mr. Charles W. Jenks, of Boston, one of the owners of this interesting mine, I am enabled to lay before the Institute a suite of specimens, illustrating its peculiar formation and the paragenesis of mineral species which it presents; and a recent brief visit and rapid reconnoissance of the locality permit me to supplement this exhibition with a general description, based upon personal observation. The mine is situated upon the Culsagee Fork of the Tennessee River, in Macon County, North Carolina, a few miles from Franklin. The most practicable route by which it can at present be visited is by wagon (or preferably on horseback) from Seneca City, S. C., a station on the Charlotte and Atlanta Air Line Railroad. The itinerary is as follows: to Walhalla,* nine miles; Walhalla to Highlands, twenty-nine miles; Highlands to the Culsagee, fourteen miles. By passing the night at or near Highlands, the mine can be reached and examined and the return to Highlands made on the second day; and the round trip, if performed in the saddle, can be completed in three days from Seneca City. It is not easy, with due regard to steed and rider, to do it in less time. The rough and precipitous mountain roads do not permit rapid travel ; and the journey is at best a fatiguing one. But its slight hardships are overpaid by the stimulating effect of the climate and the great beauty of the scenery, both of which are destined to become more widely known than at present, to seekers for health and pleasure. Indeed the town of Highlands, already named, is almost entirely made up of northern immigrants, attracted by these advantages and by the inducement of cheap land for agriculture and stock-raising. The Culsagee or Sugartown fork of the Tennessee traverses the belt of ancient crystalline schists on the west flank of the Blue Ridge. This belt abounds in valuable minerals. Among those of the nonmetallic class may be mentioned graphite, soapstone, serpentine, ashes- * A branch or cross railroad is in operation as far as Walhalla ; but the single daily train runs at an hour not convenient for this expedition ; and Seneca City is probably the best starting-point. At all events, I obtained there an excellent mount for the trip.

Jan 1, 1879

By S. L. Payne, J. P. Morris, R. L. Kipp, G. R. Zellars

The activities of iron and nickel in liquid Fe-Ni alloys were determined by measuring the vapor pressures of iron and nickel above the alloys and comparing with the vapor pressures of the pure metals. Nickel was found to deviate negatively from Raoult's law over the entire composition range. Iron behaves ideally down to 0.7 mole fraction but shows negative deviations at lower concentrations. At 1600°C the activity coefficients at infinite dilution are 0.40 for iron and 0.66 for nickel. 1 HE formulation of the conditions of chemical equilibrium between liquid metals and gases or slags is an important application of thermodynamics to pro- cess metallurgy. Usually the metal and slag phases are solutions of several components; and for accurate calculations, it is often necessary to use the activities of the components in place of their concentrations. Data concerning activities, however, are quite meager. The evaluation of the activities of iron and nickel, presented in this paper, is part of a project to determine activities in iron alloys at elevated temperatures.

Jan 1, 1960

Discussion of the paper of E. C. HARDER, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2573 to 2586. I. C. WHITE, Morgantown, W. Va.-I have seen some of the great iron-ore deposits described in this paper. -One of these in the State of Minas Geraes appears to be an immense mountain of iron ore about 2,000 ft. in height. All over its surface from bottom to top may be seen large masses of rich iron ore, varying in weight from a few pounds to several tons, and from all that one can judge without exploitation, the quantity of available ore is certainly very large in this particular mountain. Whether it will prove a mere surface deposit or shell, like the famous Iron Mountain of Missouri, is for future exploration to determine. The question of transportation is the main factor in determining the availability for exportation of these Brazilian iron ores. There is no coal in Brazil that can be manufactured into coke without expensive previous treatment, since the best of the raw coal in the States of Rio Grande do Sul, Santa Catharina, and Parana, contains about 35 per cent. of ash, of which about 6 per cent. is sulphur, and coal of this composition cannot be utilized in iron smelting without purification. When I was chief of the Brazilian Coal Commission in 1904 to 1906, I had a cargo of this coal shipped to Balk, Germany, and treated in the great coal-testing plant of the Humboldt Engineering Works, located just across the Rhine from Cologne. It was found that by crushing and washing the Brazilian coal, it yielded 33 per cent. of briquetting coal, containing only 10 to 12 per cent. of ash (of which 1 per cent. was sulphur), and 42 per cent. of slack coal, with 25 per cent. of ash and low in sulphur, so that about 33 per cent. of the Brazilian coal could be converted into coke of fair quality, as shown by the following average of three analyses, using air-dried coal, of briquets made from the Barro Branco coal bed, State of Santa Catharina: Moisture 1.56 Volatile matter 31.66 Fixed carbon 56.73 Ash : 10.05 Total 100.00 Sulphur 1.34 Phosphorus 0.003 B.t.u 13,395

Jan 4, 1915

Application of Kutter's Formula to Gases Discussion of paper by F.-ERNEST BRACKETT, presented at the Pittsburgh Meeting and issued, as Pamphlet No. 1578-A-F, with MINING AND METALLURGY, June. 1926. C. S. WITHERELL, New York, N. Y..(written discussion).-There is no reason to doubt that the relationship between the rate of, flow and. the impelling force of all fluids can be expressed by a general typical equation that takes cognizance of all relevant factors such as density, viscosity (or its reciprocal, mobility) and nature of channel-walls. Most fluids that are commonly conveyed by flow in confined channels are so highly mobile that they may be considered non-viscous, hence for these fluids the factor of viscosity does not need to appear in the equation. Water is the outstanding example of this class of fluids and its dynamic behavior has been so thoroughly investigated that proven formulas pertaining thereto, be they rational or empirical, would naturally serve as prototypes for the other non-viscous fluids. As non-viscous fluids can be classed all gases and vapors, most unsaturated aqueous solutions, gasoline, alcohol, etc. Viscous fluids comprise those that have a sluggish flow such as most oils, tar, molasses, etc., the' high viscosity of which is due to shearing resistance between molecules, a force that must betaken into account in figuring the flow of fluids of this class.

Jan 10, 1926

By A. Q. Tool

THE necessity of accurate temperature measurements in the glass-making industries is today being much more widely appreciated than in the past. The introduction of the modern simplified and perfected pyrometric methods in connection with exact regulation of furnace temperatures has caused a marked improvement in the glass product with a quickened rate of production. An example of the processes in which much improvement has been and still can be made is that of annealing or heat-treating the glass. This is one of the most delicate processes in glass manufacture and one that requires a most careful furnace control. The heat treatment is undertaken to decrease the possibility of breakage and, in glass for fine optical instruments, to prevent serious warping of accurately ground and polished surfaces and to make the glass more uniform throughout to the passage of light waves. These objects are accomplished by removing all the harmful stresses that exist in a piece of glass when it has been cooled too quickly or unevenly. Such stresses exist, for example, after it has been pressed, cast, or otherwise worked. Thus the process of annealing consists of heating the glass evenly to the temperature at which it softens just enough to relieve these stresses in a reasonable time and then cooling slowly and uniformly until the glass hardens again. Accordingly, the things that must be investigated and determined in order to anneal glass without loss of time are, the annealing temperature, the time that the glass should be held at this temperature while the stresses relax, and the quickest cooling procedure that will give satisfactory results. After these characteristics of the glass are known the problem is one of pyrometry and temperature control entirely. In cases when it is known that a glass article will be required to withstand some definite type of heat or mechanical shock it is often possible, by a proper heat treatment, to produce such a distribution of the stresses in the glass that it will be enabled to resist these shocks more effectively.

Jan 9, 1919

By J. H. Wiggins

Granting that about 600,000,000 bbl. of light oil will be produced in the United States this year and taking the Bureau of Mines' statement that 71/2 per cent. of the total crude production will be lost before the finished gasoline is shipped from the refinery, the volumetric evaporation will be 45,000,000 bbl. of the cream of the gasoline. This is a ConseNative figure and is equivalent to 1,890,000,000 gal. The real value of this liquid is at least 150 per cent. of the value of an equal volume of motor fuel. At only 10 c. per gal., the value lost is $189,000,000; at 15 e. per gal. the loss is $283,000,000. If 750,000,000 bbl. of light and heavy oil are produced here this year and the average price per barrel is $1.333, the gross return to producers will be $1,000,000,000 and the net returns about $200,000,000, if the cost of production is only $1 per barrel. Thus, the evaporation bill is about 20 per cent. of the gross income and is equal to the net income of the crude-oil producers. Two other comparisons with popular phases of the petroleum industry will help give an adequate conception of the evaporation problem. These are: cost of preventing evaporation compared to cost of cracked gasoline and volume of gasoline evaporated compared to volume of gasoline manufactured from natural gas. When gasoline is manufactured from heavy oils by the cracking process, there are two important divisions of the total cost of the product: the manufacturing cost, such as plant cost, operation, maintenance, etc., and the cost of the barrel of heavy oil, from which the cracked gasoline is made. In preventing evaporation loss the cost first mentioned enters into the total cost, but the second cost is eliminated; that is, no charge is necessary for stock from which to manufacture the saving. A detailed analysis of these two costs on a large scale shows that the net income from a dollar spent in preventing evaporation loss from the lease through the refinery is twice the net income from a dollar spent in cracking. Of

Jan 1, 1924

By Howard S. Bryant

Kansas maintained its fourth position on the list of all oil-producing states, for the ninth consecutive year. Total crude-oil production during 1935, as reported by the Oil & Gas Journal, was 53,364,446 bbl. on 97 per rent tank table calculations. This represented an increase of 17 per cent over the production in 1934, which had been the all-time peak of production in Kansas up to that time. Many of the 51 new discoveries of the year, listed in Table 2, did not have a pipe line outlet until about January, 1936; therefore did not contribute to the 1935 production of the state. The potential of all wells in Kansas at the end of the year was 998,-000 bbl. per day, and the daily allowable was 143,000 bbl. per day, showing proration to the extent of 14 per cent of capacity, under the rules of the State Corporation Commission. Several important new pipe lines were built into western Kansas by extending older lines from east to northwest, providing additional outlets for new crude-oil production, and increasing the service facilities from the older oil fields. The crude-oil price level remained unchanged throughout 1935 as it did in 1934, the price of Kansas 36" gravity crude being quoted at $1 per barrel. However, on Jan. 9, 1936, the price of this gravity oil was raised to $1.10 per barrel. Following the trend of the past several years, drilling activity was largely in western Kansas, and showed a still farther westward push from last year. A relatively high percentage of successful wildcat wells at a relatively shallow drilling depth, combined with the expiration of leased acreage assembled before the depression, caused the rapid exploration and development campaign, begun in 1934, to continue. This has caused the opening of more new fields in 1935 than during any previous year in the history of oil production in Kansas. A summary of the results of drilling in western Kansas is given in Table 2. Eastern Kansas had considerable drilling, showed six new fields or extensions of oil fields, but in the limited space of this paper such developments cannot be described.

Jan 1, 1936

By H. B. C. Nitze

A description of some of the magnetic ore-deposits in this region should be of interest to the mining and metallurgical public, inasmuch as very little has been said or written concerning them. I refer to the magnetite deposits of Franklin and Henry counties, Va., and of Stokes county, N. C. These deposits remained comparatively unexplored until recently, when the construction of the Roanoke & Southern R. R. through this territory has called attention to them, by furnishing the means of transportation for the ores. It is true that the ores have long been known, at least locally, and were smelted in catalan forges and old-fashioned, cold-blast charcoal-furnaces long before and during the late war. At the present time, however, the old workings are caved in, filled up and over-grown to such an extent that, as a rule, but little can be learned from them. No prospecting of any consequence has been done, and as my time was too limited and the territory to be examined too extensive to permit additional openings of a more satisfactory nature to be made, the incormpleteness of some of the data I have to offer (notably, those referring to the absolute width of the veins) will be pardoned. It will hardly be necessary to say that this ore-bearing formation belongs to the Archaean, or Eozoic age, the usually occurring rocks being schist, shale, gneiss, granite, sandstone and quartzite. The stratigraphy is, as a rule, quite regular (excepting in the Danbury section, Stokes county, N. C.), the general strike being northeast and southwest, and the dip nearly vertical. The country is gently roll-

Jan 1, 1892

By M. E. Wadsworth, P. H. Yu, C. K. Hansen

A study of the rate of dissc5lution of chalcopyrite (CuFeS2) in acidic solutions under oxygen overpressures was carried out by measuring the rate of formation of cupric ions in solution. Effects of temperature, oxygen partial pressure, surface area, and concentration of sulfuric acid were evaluated. A sized batch of chalcopyrite was leached in the temperature range of 125° to 175°C and in the pressure range of 75 to 400 psi of oxygen. In 0.5 N H2SO4 all products of reaction went into solution except for trace amounts of elemental sulfur. The dissolution of chalcopyrite followed linear kinetics and was essentially independent of hydrogen ion concentration for H2S04 concentrations between 0.2 and 0.5 N. The oxygen dependence indicated adsorption approaching limiting values with increasing oxygen pressure. The linear mechanism was explained in terms of steady-state adsorption of oxygen at the chalcopyrite surface followed by a surface reaction. The enthalpy of activation for adsorption of oxygen was found to be approximately 33 kcal per mole. An activation enthalpy of approximately 9 kcal per mole was observed for the surface reaction. Charge transfer reactions are not rate controlling in the process.

Jan 1, 1973

By George W. Riter

OUR mineral-land laws need revising so as to provide definite title at the outset to the mineral deposits within any definite piece of land. The laws as they now stand, especially those applicable to lodes, breed uncertainty as to rights of possession prior to patent; and to my mind this is the worst feature of all, worse even than the apex bugbear. It is now almost impossible for anybody to tell-with certainty what mineral rights exist within any area that is not covered by patent, or whether any valid rights exist at all. Our system is unique in permitting individuals to appropriate and exploit mineral lands of the public domain without notice of any kind to the Federal government, and to relinquish them without any ceremony at all. The result is a clouded record that cannot be cleared up until each claimant is put to some sort of final proof. In order to accomplish this, new Federal legislation will be required. The requirements for a mineral survey and the proceedings for patent have always been cumbersome and expensive; and perhaps out of regard for the poor claim owner, who can ill afford the outlay for that sort of thing, the law does not require him to go. through it unless he chooses to do so. Consequently, every active mining district has become encumbered with tangled groups of doubtful or conflicting locations, whose rights and boundaries, when any valuable ore is found, must usually be determined by lawsuits that are as expensive and as distressing as the stakes are high. So deeply has litigation entered into our mining system that a claim whose rights have never been disputed would probably be set down offhand, by $miner of the old school, as of no value. Think of the litigation over rights of possession on the Com-stock lode—12 leading companies involved 'in an aggregate of 245 suits within a period of less than eight years! Ambiguous local records; the chance of erroneously placed or obliterated monuments; doubt as to the sufficient performance of the statutory annual labor; uncertainty as to prior conflicting or overlapping locations; anxiety as to the changing attitude of the Department of the Interior and the Forest Service—such considerations as these make an unpatented mining claim an unclean thing in the eyes of possible investors. Is it any wonder that they keep themselvesand their money at a safe distance,

Jan 1, 1915

By A. R. Troiano, E. A. Steigerwald, F. W. Schaller

D. N. Williams(BatteZle Memorial Institute)-The authors have presented an extensive collection of arguments pertaining to the role of stress in hydrogen embrittlement. The basic assumption of these arguments is that stress is essential as a driving force for diffusion of hydrogen. However, in view of the rapid diffusion rate of hydrogen in steel at low temperatures as evidenced by the ability to alloy with hydrogen by electrolytic charging, it seems unlikely to me that stress acts in this manner. Instead, I would like to suggest that stress may be essential for the nucleation of hydrogen in steel. I believe that such an assumption would equally well satisfy the experimental data presented by the authors. I should also like to comment on the interpretation of the data presented in Figs. 5 and 6. Fig. 5 shows the effect of hydrogen content on ductility in a rupture test. The curve as drawn by the authors indicates an abrupt transition from ductile to brittle behavior at about 0.001 amp per sq in. (5 ppm). The data points would equally well support a gradual transition from ductile to brittle behavior extending over the range from 0.0008 to 0.02 amp per sq in. (4 to 8 ppm). A gradual transition would be the ex-

Jan 1, 1962

By Herbert Clark Hoover, Lou Henry Hoover

SINCE I have written of the varied work of pre- paring the ores, I will now write of the various methods of smelting them. Although those who bum, roast and calcinea the ore, take from it something which is mixed or combined with the metals ; and those who crush it with stamps take away much ; and those who wash, screen and sort it, take away still more; yet they cannot remove all which conceals the metal from the eye and renders it crude and unformed. Wherefore smelting is necessary, for by this means earths, solidified juices, and stones are separated from the metals so that they obtain their proper colour and become pure, and may be of great use to mankind in many ways. When the ore is smelted, those things which were mixed with the metal before it was melted are driven forth, because the metal is perfected by fire in this manner. Since metalliferous ores differ greatly amongst themselves, first as to the metals which they contain, then as to the quantity of the metal which is in them, and then by the fact that some are rapidly melted by fire and others slowly, there are, therefore, many methods of smelting. Constant practice has taught the

Jan 1, 1950

By William J. Gillich, Gerald L. Moss

PREVIOUS studies of the shock loading of randomly oriented polycrystalline aggregates have firmly established that, after rather short load duration, hydrostatic compression closely approximates the shocked state.' However, McQueen deduced from pressure measurements with good time resolution that, during shock loading, metals begin to undergo a stress relaxation at the yield stress. He suggested that the relaxation is due to plastic deformation accompanying the change from a one-dimensional compression to a three-dimensional, hydrostatic, compression.' Stress relaxation may occur faster as stress is increased above the yield stress, but the existence of unidirectionally compressed states for finite times suggests that the concept of a unidirectionally distorted lattice should furnish considerable insight into the mechanical behavior of materials subjected to shock loading. Here, a crystallographic analysis is presented for the hypothetical situation where atom motion may be considered as unidirectional which, as indicated above, is a useful extension of the macroscopic concept of shock loading to the microscopic domain. Only motion caused by the com-pressive forces is treated; i.e., lattice vibrations upon which this motion is superimposed, as discussed by Fitzgerald, are ignored.3 The purpose of the analysis to be presented is to develop a description for single crystals of the lattice rotations that occur for idealized uniaxial strain deformation. The usefulness of such an analysis in realistic deformation is to give a method of specification of those properties of an initially distorted lattice which would affect the subsequent deformation. Non-axial complications that arise experimentally, such as off-axis rarefaction waves, must be treated in proper context. Consider the material element shown in Fig. 1 and let the compression be uniform at all regions of the element. Then, any interior point of the element is displaced in proportion to its distance from the base of the element. Accordingly, if the top of a unit element is displaced by an amount, (-K), with respect to the base, a point P(X, Y) will be displaced by (-KY). Crystal planes are, therefore, rotated by the compression. Analysis of this rotation may be accomplished from the geometry shown in Fig. 1 where the line OP is the edge of the plane {hkl} and N is its normal. The orientation of the crystal plane with respect to the shock direction is specified by the angle, before deformation. After deformation the edge of plane {hkl}

Jan 1, 1969

By G. Sachs, S. I. Liu

Introduction In a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24 ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in Fig I,$ the ductility (e~) retained after prestraining in tension by a certain amount (el) and measured in a subsequent tension test is represented by a straight line sloping down under 4s°. If a compression of the same magnitude as the first tension is inserted (€2 = — €1) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.~ As also shown in Fig I, the ductility in subsequent tensile tests decreased with com- pression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount el, subsequently straining in compression by an amount e2, and finally determining the retained &apos;ductility, e,, in a tensile test. Prestraining in tension is then represented by el > o and e2 = o. Prestraining in compression is given by e~ = o and e~ < o. Balanced cyclic straining is defined by the condition el > o and cz = — 61. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, el, and the compression strain, e2, within extreme limits; el varied between 0.06 and 0.28 and e2 between — 0.008 and —0.h approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date, The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the sub-

Jan 1, 1949

By N. M. Raju, B. Singh

The paper seeks to present the results of experimentation in room and pillar stopes with different ground conditions to determine the safe working span. In the experimental stopes, ground movement was monitored with gradual widening of the room span. The field measurements included closure between the stope walls and the extent of ground movement in the hangwall using borehole extensometers. hock bolting was used as an exclusive support system which enabled introduction of scrapers for improving productivity. In one nine, phosphate bed, 3 to 3.5 m thick dipping at 45O and overlaid by weak laminated shale, was worked at shallow depth of cover. h the experimental panel, five s topes were worked with spans varying from 5.5 to 7 m. In the second mine, the chalcopyrite orebody up to 6 m in thickness dipping at 25 - 30" was worked at a depth of 1100 m. The hangwall consisted of fairly competent schistose rocks and therefore 10 to 15 m wide spans could be experimented. The field measurements confirmed that in the phosphate mine with weak shale roof, 7 m span could be safely worked with subsequent caving of the bolted roof. In the copper mine, 15 m span could be worked and the stopes required subsequent backfilling for better ground control.

Jan 1, 1983

By Carl Henrich

I have read with particular interest that portion of the discussion by Anton Eilers referring to the high-lime (and also high-alumina) slags made by August Raht in 1881, while smelting the Horn Silver ores at Franklin, Utah. The two analyses of such slags, furnished by Mr. Raht to Mr. Eilers are: (a) Not determined in this analysis. (b) Not given in Mr. Eilers&apos; paper. Oxygen ratio, A1 as base. I. 0 in acid: O in base:: 18.1:18.9:: 0.96:1 11. 0 in acid :O in base:: 18.7:17.5::1.06:1 Average: 18.4:18.15=1.01:l Oxygen ratio, AI as acid. I. O in acid: O in base: :23.2:13.8:: 1.68:1 11. O in acid: O in base::23.1:13.5:: 1.76:1 Average: 23.15:13.4 = 1.73:l By assigning to alumina the the of a base, Mr. Eilers deduces the formula 3Feo.-2SiOa + 4Cao.2SiO². The nearest approach to a simple formula expressing the average composition of these slags, which I can figure, is 9RO.Al2O3.6SiO2. Allowing a ratio of 4Feo : 5Cao, we have for this formula:

Jan 1, 1917

By Yoshinao Nakada

In many experiments involving electropolishing such as electropolishing during deformation and electrothinning of deformed metals for electron microscopy, it is usually assumed that the specimen temperature is the same as the temperature of the polishing bath. In order to test this assumption, the interior temperature of aluminum single and polycrystals was measured while they were being electropolished. Specimens were 1/4 by 1/4 by 6 in. and were of 99.99 pct purity. A small hole 1 in. deep was drilled axially at one end of the specimen so that a copper-constantan thermocouple could be inserted. The electropolishing solution was 4 parts methanol (reagent grade) and 1 part perchloric acid (70 pct). The electropolishing was performed using an apparatus shown in Fig. 1. The electropolishing solution was stirred by a motor-driven stirrer and was cooled to —5°C with a mixture of methanol and dry ice. Electrolyte temperature was measured and remained at -5°C during the electropolishing. Current density of 0.3 amp per sq. cm was used. When the current was turned on, after about a 5-sec delay, the temperature began to rise rapidly until it reached 65°C. In order to determine whether the temperature measured was localized, the thermal expansion of the specimen was meas-

Jan 1, 1965