Search Documents

By Howard Scott, Henry S. Rawdon

The method of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallog-raphists. The usual procedure1 2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas (chlorine, hydrochloric acid or similar gas) for a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being admitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo. The studies of Rosenhain, Humfrey, and other workers 4, 5, 6, 7, 8 dem-

Jan 1, 1922

By Arthur F. Johnson

THE principal costs of making a pound of aluminum are for 9 kw-hr of electricity and for 1.9 Ib of the oxide (A1203) called alumina. A pound of alumina is made by digesting 2 or 3 lb of bauxite in hot caustic solutions, settling and filtering out the oxides of silicon, iron, and titanium and precipitating and calcining the A1203 as a pure, white powder. The cost of foreign bauxite delivered at an alumina plant in the U.S. may equal or exceed the cost of its chemical treatment to make alumina. Some of the principal factors affecting costs in the utilization of foreign bauxites are: transportation from mine to market, mineralogical and physical composition of the bauxite, thickness of the bauxite beds and their clay and forest overburden, amen- ability of the bauxite to beneficiation and to caustic extraction of the alumina, and lastly size of bauxite deposits and rate of mining employed.

Jan 6, 1954

By C. C. Wright, R. J. Day

ALTHOUGH data on the exact tonnage of recoverable coal silt are not known, the quantity produced in 1943 was estimated to be over five million tons for the anthracite region of Pennsylvania alone. Since that time the recovery of the No. 5 buck- wheat size previously included in silt estimates has increased greatly thus reducing the total silt tonnage. As a compensating factor, however, the methods of recovering silt previously escaping into the rivers and streams have been markedly improved so that the net figure may not have changed materially. Comparable estimates for bituminous coal are lacking, but undoubtedly the silt represents a significant tonnage. With the trend toward increased wet cleaning of the smaller sizes of bituminous coal, it is to be expected that even greater quantities of silt will be available in the future. The raw silt from anthracite collieries usually contains a high mineral matter content, but technological developments in fine coal cleaning have been making rapid advances and it appears probable that more extensive use of these methods will be employed in the near future. Bituminous coal silt in many instances contains a similar high mineral matter content. As with anthracite silt, however, the cleaning of this material, where necessary, appears both technologically and economically feasible. With a view to upgrading the size and value of silt, considerable laboratory and pilot plant work has been conducted by a number of organizations on what is commonly known as pelletization. Actually the process is one of extrusion in which the moist silt is extruded from a die in the form of rods, which usually break into relatively short lengths-a few inches long-as they fall from the die. Fig I is a photograph of some extruded 3/8-in. diam pellets and of the anthracite silt from which they were produced. This technique of producing larger sized material from fines is by no means new, having been used extensively by the industrial carbon and clay industries for years.' The application of the process to coal silt appears, however, to be relatively new. The first major program of investigation dates back only to July 1945, when a group of engineers representing the Anthracite Institute, The Pennsylvania State College and the J. F. Pritchard and Co. conducted preliminary tests on the extrusion of anthracite silt at the Floridin Co. plant at Warren, Pa. Since that time these three organizations-individually, together, and in co- operation with other interested groups- have actively pursued work on various phases of the problem. Much of the early history and details of the laboratory and pilot plant work by the Anthracite Institute, has been reported by Mulcey and Eckerd.2 It is the purpose of this paper to report additional information on the process, especially with respect to the factors influencing the quality and use properties of the product, and the current develop

Jan 1, 1948

By H. T. Green, R. M. Brick

True stress-strain data on alloys of pure iron with up to 2.4 pct Al were obtained in the temperature range +100° to —185°C. Alumi-num was found to reduce yield and flow stresses of iron at low temperatures but to have little or no effect on ductility. The effects of temperature and composition on strain hardening are discussed. SEVERAL independent studies of the behavior of high purity iron binary alloys at low temperatures are now in progress in attempts to evaluate systematically the variables affecting the low temperature brittleness of ferritic steels. This paper reports the results of one such investigation in which the tensile properties of aluminum and aluminum plus silicon ferrites were measured from 100" to —192°C. True stress-natural strain data have been obtained in order to evaluate as many as possible of the parameters which describe the behavior of the materials involved. In comparable studies at the National Physical Laboratory in England, iron and iron alloys of high purity have been produced' and tested at subat-mospheric temperatures.' True stress-natural strain curves were obtained there also. The purest iron contained 0.0025 pct C and 0.001 pct O and N. Even this, as normalized at 950°C following hot rolling, showed little ductility at -196°C. The grain size was ASTM No. 3, and the room-temperature yield strength was 17,800 psi (which seems too high for pure iron). Some of the NPL irons contained considerably more oxygen and demonstrated intergran-ular fracture at —196°C. The authors2 carefully differentiated between intergranular fractures associated with excessive oxygen content and transcrys-talline cleavage with little ductility encountered at —196°C in the purer material. The cleavage stress was half again as great as that associated with inter-granular fracture. Test Material, Preparation, and Procedures Of a number of Fe-A1 alloys produced, eight were considered to be sufficiently pure for testing. Partial chemical analyses (Table I), low observed yield points, and high ductilities indicate these alloys to be comparatively pure for vacuum-melted irons of sizable ingots, 5 Ib or more. To produce the binary Fe-A1 alloys, electrolytic iron was melted in air, cast into slabs, and rolled to strips 0.010 in. thick. These strips, joined into a continuous ribbon and wound into 2 1/2 in. diameter spools, were subjected for four weeks to a moving atmosphere of purified dry hydrogen in a stainless-steel tube at 1050" to 1150°C. Charges of these spools were melted in beryllia crucibles under good vacuums (1 micron), and aluminum (99.97 pct Al) was added to the melts. Compositions of these alloys are recorded in Table I. The ingots were hot forged and then cold rolled at least 65 pct to 3/8 in. rods which were vacuum annealed to the desired grain size, approximately ASTM No. 4, prior to machining into tensile test bars. All tensile specimens had gage sections 1 in. long, with a fillet of 1.5 in. radius to the shoulder. Gage diameters were 0.250 in, except for a few rods where additional cold work required use of a 0.200 in. gage section. After machining, 0.002 in. was removed from the gage diameter using 240, 400, and 600-grit metallo-graphic papers. The final polish with 600 grit left the fine scratches running in the longitudinal direction. By this means, surface metal strained during machining was removed. A few specimens heat treated after machining were similarly reduced 0.004 in. to remove any material affected chemically by the atmosphere during heat treatments, as is discussed in a later section. Tensile tests of the eight alloys at constant temperatures from +100° to —185°C were performed in apparatus which has been described." The essentials include a double-walled insulated metal vessel which contained the liquid heat-transfer medium surrounding the test specimen. A constant temperature was maintained by means of a pyrometer which regulated the pressure of dry air driving liquid air through a copper coil. Temperature variation was less than ±2°C during a specific test. For axial straining, two lengths of case-hardened chain, terminating in simple shackles, loaded the specimen through threaded grips. The lower grip bar passed through a hole in the bottom of the test vessel to which it was joined by a thin-walled

Jan 1, 1955

By Ming-Kao Yen

A considerable amount of work has been reported in the literature in regard to the texture and earing behavior of copper strip. The rolling texture of copper has been confirmed as (110) [112] and (112) [111], which yields ears of a drawn cup at the position 45" from the rolling direction.1-3 The recrystallization texture has been established as the cubic or (100) [001] texture, where the earing positions are at 0" and 90" to the rolling direction.4-8 It has also been reported that in the development of cubically aligned grains of copper strips, the percentage of this cubic texture increased with an increase of final reduction and final annealing temperature.8,9 A comprehensive study on H.C. copper (British commercial copper of high-conductivity quality = Cu 99.95 pct, O2 0.03 pct, Ag 0.003 pct, Fe 0.005 pct and Pb < 0.001 pct) was made by Cook and Richards.6 They concluded that the recrystallization textures could be described as one or more of the following textures: (1) a single texture (100) 10011, (2) a twin texture (110) [112] and (3) a random orientation, depending upon the previous history of the specimen concerned. The effect of various alloying additions in copper was reported by Dahl and Pawlek.10 They found that certain alloying additions, such as 5 pct Zn, 1 pct Sn, 4 pct Al, 0.5 pct Be, 0.5 pct Cd, or 0.05 pct P suppressed the formation of cubic texture. Brick, Martin and Angierll reported that the cold rolled textures due to various additions fitted a rather simple pattern. However, the recrystallization textures were subject to very considerable variations. In the discussion of this paper, Baldwin stated that deoxidized copper containing 0.02 pct P gave a complicated recrystallization texture at lower temperature. When this copper was annealed at high temperature, a single texture appeared which was described as (110) [ill] but. according to a pri- vate communication from Baldwin, this orientation reported was in error and should have been reported as (110)[112]. He also reported that the earing positions of drawn cups were at 60" to the rolling direction.12 Recently, Howald, in his discussion on the paper by Hibbard and Yen,13 reported that the rolling texture of phosphorus deoxidized copper, containing from 0.006 to 0.020 pct phosphorus, was of the pure copper type. When these coppers were annealed at lower temperatures, they exhibited a random orientation, and when they were annealed at higher temperatures they had a mixed (111)[110] and (100)[001] texture, depending on the severity of the final reduction and annealing temperature. However, the specific influence of phosphorus and other impurities on the recrystallization textures and the deep drawing properties of copper strip has not been thoroughly reported. Therefore, an attempt has been made in the present work to determine the rolling and recrystallization textures and also the earing behavior of five types of commercial copper and thereby to evaluate the effect of phosphorus and some other significant impurities on the development of texture for cold reductions of about 87 to 89 pct. Materials Used The five types of copper employed in the present investigation were two phosphorus deoxidized coppers of different phosphorus content (0.007 and 0.013 pct P), an oxygen-free copper (OFHC), an electrolytic tough-pitch copper, and a fire-refined tough-pitch copper. These materials were subjected to a thorough spectroscopic and chemical analysis. The designations and the chemical compositions were as shown in Table 1. The coppers, FA1, FA2 and FA3. were hot-forged from 3-in. billets into a ½ X 6-in. plate and cold rolled to the ready-to-finish gauge indicated below. FA4 and FA5 were hot rolled and scalped to ready-to-finish gauge. The grain size of all the materials in the ready-to-finish condition was about 0.030 to 0.045 mm. Table 2 shows the last stage of the production schedule for each copper strip used. Experimental Procedure ANNEALING, GRAIN SIZE AND HARDNESS DETERMINATIONS Specimens of each type of copper were finally annealed in air for periods of one hour at temperatures ranging from 300 to 1600°F and were subsequently cooled in air. The average grain diameter of the annealed specimen was estimated by comparing with a standard grain size chart. Hardness was determined on the Rockwell 15 T scale. CUPPING TESTS Cups were made in a blanking and drawing set, in which blanks of 2-in. diam were drawn to a cup of 1.25-in. diam with an average depth of about 0.75 in. The clearance between the punch and die was about 0.032 in. The ears of the cup were measured with a special fixture which read the height of ears to one-thousandth of an inch on every ten-degree interval along the circumference of the cup. POLE FIGURES The usual transmission diffraction method with unfiltered copper radiation was employed to determine the pole-figures of the specimens cold-rolled or annealed at 900°F. All the pole-figures were derived from the positions of intensity maxima on 111 diffraction rings of the X ray photo-grams taken at 10 rotation of a

Jan 1, 1950

By H. J. French

AT THE request of a committee of the Engineering Division,1 National Research Council, a study of the properties of boiler plate at various temperatures up to about 900° F. (482° C.) has been instigated. The following is a report of preliminary tests made on two grades of ½ -in. plate and includes a description of the apparatus used in the determination of the proportional limit. Detailed reference to the many published investigations in connection with the properties of steel at various temperatures will be omitted from this report. Suffice to state that results obtained for variation in tensile strength elongation, and reduction in area with temperature are in substantial agreement with the effects now generally considered to be correct. Comparison of proportional limit values with results obtained by other investigators will be found in the conclusions.

Jan 2, 1920

NEW YORK SECTION ALLEN H. ROGERS, Chairman, H. C. PARMELEE, Vice-chairman, FOREST RUTHERFORD, Vice-chairman, W. S. DICKSON, Secretary, 71 Broadway, New York, N. Y. J. E. JOHNSON, JR. . F. T. RUBIDGE, Treasurer, P. G. SPILSBURY. The annual meeting of the New York Section, for the election of officers and other business, was held at the Machinery Club on May 23,

Jan 8, 1918

Jan 1, 1954

By José G. Aguilera

With the imperfect knowledge that me have of the geology .of the country in general, and of the numerous mining districts in particular, it is impossible to present an accurate idea of the geographical and geological distribution of the mineral deposits of the Mexican Republic. But, notwithstanding this, it is elear that the deposits are concentrated in limited regions of the country, and that certain deposits are so closely associated as to indicate, beyond doubt, a genetic relationship. The mineral deposits are numerous, and the most of them are found in the western part of the country in a zone following a SE.-NW. direction from Oaxaca to Sonora. In the eastern

Jan 1, 1902

By K. P. Wang

Under the Communist regime marked industrial progress has been achieved on the China mainland. Within a decade, the country has been transformed from an economy primarily agricultural to one bristling with industrial possibilities. The industrial capacity of Communist China is beginning to approach that of Japan and will probably surpass it by 1962, the last year of the Second Five-Year Plan. The slogan already is Beat the United Kingdom by 1972, a goal which most observers feel will be achieved ahead of schedule. During the early years of the industrialization program in Communist China, emphasis has been placed on basic goods; hence additional time will be needed to make large quantities of the more complicated products. However, regardless of the current stage of industrial development, it is apparent that the necessary forward momentum has been created. The many capital construction projects being brought into production and the additional projects being initiated confirm this observation. The accuracy of Communist China&apos;s industrial statistics can be questioned, but their order of magnitude is clear. To properly evaluate the industrial capability of the country, differentiation must be made between the absolute quantities that reflect overall strength and the per capita quantities that reflect living standards. While Communist China is well on the road to becoming a world power, its living standards will remain below European levels for many years to come.

Jan 8, 1960

By R. J. Reynik

A semiempirial small flunctation theory of diff- sion in liquids is presented, which employs a fluctuation energy assumed quadratic for a small atomic or molecular displacement and Einstein&apos;s random-iralh model. The resulting diffusion equation is given by In these equations. D is the diffusivity, is the average liquid shite coordination number (at interatomic distance d. cm. T is the absolute temperature, xu. em, is (the diffusive displacement. K, is the quadratic fluctuation energy force constant, and rg, cm, are the radii oj diffusing atoms A and B, respectively. The quantities Xn and K are calculated from the computer-filled values of the slope and intercept. respectively. The radius of self-diffusing atom or radii and of diffusing atoms A and B are eta United and compared with values reported in the literature.. The predicted linear variation of diffusivity with. It tempera lure htm been observed in approximately thirty-iire metallic liquid systems, and in over seventy-fiee other liquid systems, including the organic .alcohols, liquified inert gases, and the molten salts, ALTHOUGH the average density within a macroscopic volume element of liquid is constant for fixed total number of atoms. pressure. and temperature, there exist microscopic: density fluctuations within the respective volume element. As such the microscopic volume available to an atom and its Z first nearest neighbors at any instant of time fluctuates above and below the average volume available to these atoms. If one assumes that liquid state atoms vibrate as in a solid. and further postulates that the mean position of any atom in the liquid state is not stationary. but shifts during every .vibration a distance 0 5 j 5 xo. then every atom in the liquid state continuously undergoes diffusive displacements which vary in the range 0 5 j 5 ro. Mathematically. for a binary liquid system consisting of atcrms A and B. the maximum diffusive displacement. .YO, is defined by the equation: where d is the average liquid state interatomic distance at specified liquid state coordination number Z. and v~ \ and vg are the effective radii of diffusing atoms A and B: respectively. For self-diffusion. r^ equals rg , and Eq. [I.] reduces to: It is interesting to note that Eq. [l] or [2] can be used to compute the radii of the diffusing atoms, provided one had an experimental evaluation of xo. As such. the computed radii could be compared with metallic or crystallographic ionic radii to ascerlain the electronic character of the diffusing atoms. Thus it is proposed that in the liquid state the n~otion of an atom relative to its original equilibrium position of oscillation represents the thermal vibration of any atom and its Z first nearest neighbors. while the small and variable displacements. 0 5 1 5 xc,. of the centers of oscillation represent the complex diffusive motions of the atoms at constant temperature and pressure. This is consistent with data obtained from slow neutron scattering by liquids1 &apos; and resembles an itinerant oscillator model of the liquid state.&apos;" It is further postulated that the atomic displacements characterizing the liquid state diffusion process are essentially a random-walk process. As such. it nlay be described by Einstein&apos;s equation:&apos; where D is the diffusivity. sq cm sec-&apos;. j2 is the mean square value of the diffusive displacement. and i> is the frequency of density fluctuations giving rise to diffusion. FORMULATION OF DIFFUSION EQUATION The effective spherical volume occupied by an atom, as a consequence of a microscopic density fluctuation which enlarges the volume available to any atom, exceeds its average liquid state atomic volume by an amount: where AV is the enlarged spherical volume, v is the radius of the diffusing atom. and j is the elementary displacement distance from the original center of oscillation of the vibrating atom to a new center of oscillation position. For small atomic displacements. where c is a constant whose value depends upon the assumed geometry of the enlarged volume. For a spherical increase in volume, c equals 4nr2. Following the treatment of Furthl&apos; and ~walin." assuming the enlarged volu~nes AL7 for the diffusing atoms are distributed in a continuunl. the probability of finding a fluctuation in the size range 0 5 j 5 xo defined by Where c includes the geometric constant cl and Eij) is the fluctuation energy causing the volume change. But the proposed model assumes all the Z first nearest-neighbor atoms are centers of oscillation. and hence the probability that any of these atoms is adjacent to a fluctuation of magnitude 05j5xo is unity. Thus:

Jan 1, 1970

By A. H. Daane, A. S. Wilson

The U-Cr system is of the simple eutectic type with some solid solubility of chromium in r and ß uranium. The eutectic occurs at 20 atomic pet Cr and melts at 859°C. The maximum solubility of chromium in y uranium is 4 atomic pet at the eutectic temperature, and in ß uranium the solubility is estimated to be 1 atomic pet. y-ß and ß-a transformations were found to occur at 737°estimatedt° and 612°C respectively. DURING 1944 and 1945, the U-Cr constitution diagram was studied in this laboratory as a part of a research program on uranium metallurgy in the Manhattan Project, and the work was described in a Manhattan Project report issued in December 1945. This paper is based on that report, which has been declassified. Prior to this study, it had been shown by other Manhattan Project workers that the low Cr-U alloys could be quenched to retain the form of uranium. Experimental The uranium used in this work was massive metal prepared in this laboratory and contained less than 0.1 pct of other elements. The chromium was 200 mesh powder obtained from the A. D. McKay Co. and was found on analysis to be 99.5 pct Cr with 0.3 pct Fe the major impurity. Alloys, weighing 400 to 600 g, were prepared by induction heating the components to 1700°C in slip-cast ZrO, crucibles in a vacuum of 3x103 mm Hg. TO prevent too violent agitation of the melt by the induction field with subsequent crucible breakage and sample loss, the ZrO2 crucible was placed in a graphite crucible, which was surrounded by a layer of powdered carbon insulation 2 to 3 cm thick. Polished vertical sections of the alloys were examined microscopically to confirm their homogeneity. Heating and cooling curves were taken on the alloys by reheating them in ZrO, crucibles to 1200°C and inserting a mullite-protected chromel-alumel thermocouple into the melt by means of a slip seal in the vacuum head of the furnace. A recording potentiometer traced the curves which had a slope of from 3" to 6" per min. Samples of the alloys were prepared for metallo-graphic examination by conventional mechanical polishing techniques followed by an electrolytic polish in an ethylene glycol-phosphoric acid-ethyl alcohol bath. The structure of the alloys was brought out clearly by this procedure so that no further etching was required. Samples for chemical analysis were taken from drillings from the top, center, and bottom sections of the alloys. The uranium was determined by titra-tion with Ce(SO1)2, while the chromium was titrated with FeSO,; the uranium and chromium totaled at least 99.6 pct in all of the alloys prepared. X-ray samples were prepared by filing bulk specimens in a helium-filled glove box and annealing the resulting powder in a zirconium-gettered helium atmosphere. A 114.6 mm diam Debye-Scherrer camera and a Weyland nonsymmetrical self-focusing camera were used with filtered copper radiation to obtain the powder X-ray diffraction data. Results The data obtained in this study have been combined to construct the constitution diagram of the U-Cr system shown in Fig. 1 where the arrests observed in cooling curves are indicated by dots. The liquidus arrest was quite distinct in thermal data taken on alloys in the range 0 to 20 atomic pct Cr. The eutectic arrest was not observed in studies on the 2.5 and 4.5 pct Cr samples but appeared in the 7.5 pct samples, which suggested some solubility of chromium in y uranium. On quenching from 859 °C, the 2.5 pct sample showed but one phase while the 4.5 pct sample contained a small amount of the eutectic along the grain boundaries; see Figs. 2 and 3. From this the maximum solubility of chromium in r uranium has been set at 4 pct. X-ray studies on these samples showed that the r phase was not retained at room temperature by quenching, but in each case a pattern was observed .which has been identified with the ß phase of uranium. Thermal data show the y-ß transformation of uranium lowered to 737°C as a consequence of this solubility. On quenching from the ß range (660°C), precipitation of chromium in the primary uranium is observed in the 2.5 and 4.5 pct Cr samples (see Figs. 4 and 5),

Jan 1, 1956

By R. B. Burt, James A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1-the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2-power required for pumping, 3-pump selection. The basic factors for a given problem will include: 1-weight per unit of time of solids to be handled, 2-specific gravity of solids, for calculation of volume, friction and power, 3-screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4-shape of particle or some means of determining a friction constant, 5-effects of percentage of solids, 6-development of a viscosity factor to be used in the overall calculations, 7-calculation of the lower limits of pipeline velocities permissible, 8-calculation of total head, pump horsepower, and 9-setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble, phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; -14 +35 mesh, 11.4 pct; -35 +150 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The -150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble, content of the matrix, i.e., the +14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum -velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is, smooth and- polished because of the scouring, action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump, changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1952

By P. Chaudhari, Michael B. Bever

The heat of solution at infinite dilution of selenium in bismuth, the heat of mixing of selenium and bismuth, and the limit of solubility of selenium in bis~rzuth have been determined at 573, 623; and 663°K by metal solution calorimetry. The heat of forrrzation of the compound Bi2Se at these temperatures has been determined from the heat effects associated with the precipitation of the compound from a saturated solution oj selenium and bismuth. The published information on the thermodynamic properties of the system Bi-Se is limited. The heat of solution at infinite dilution of selenium in bismuth at 623°K has been measured.&apos; The heat of formation at 273 K1 and room temperature2 and the heat capacity at 80 K3 of the compound Bi2Se3 have been reported. An estimate of the heat of formation of the compound BiSe at room temperature has been published.2 Information on the phase relations in the system Bi-Se is available.&apos; In the investigation reported here the following quantities have been determined at 573", 623", and 663°K: 1) the heat of solution at infinite dilution of selenium in bismuth, 2) the heat of mixing of selenium and bismuth in bismuth-rich solutions, 3) the limit of solubility of selenium in bismuth, and 4) the heat of formation of the compound BizSe. These quantities were determined by the addition of selenium to bismuth-rich solutions in a metal solution calorimeter. The determination of the heat of formation at the tem- perature of the calorimeter bath involved the precipitation of the compound from a saturated solution in the calorimeter. 5,6 This method differs from that commonly used which requires the addition of the compound and of a mechanical mixture of its components and yields the heat of formation at the temperature from which the additions are made (273 K EXPERIMENTAL PROCEDURE AND CALCULATIONS The solution calorimeter has been described in detail.&apos; Pure bismuth (99.999+ pct) was used as the bath at the start of a run. The calorimeter was calibrated with small amounts of bismuth added from 273°K; the differences of the heat contents of bismuth at 273°K and the temperatures of the baths are listed in Table I. After the calibration, additions of hexagonal selenium (99.999+ pct) were made. Loss of selenium by evaporation was negligible. No unusual experimental difficulties were encountered.9 The differences in the heat contents10 of selenium at 273°K and the temperature of the bath, listed in Table I, were subtracted from the measured heat effects to give the "adjusted heat effects". The methods by which the heat of solution at infinite dilution, the

Jan 1, 1968

By C. G. Dunn, F. W. Daniels

IN recent publications1-5 the existence and behavior of subgrain boundaries in high-purity metals has been clearly brought to light. Lacombe and Beaujardl by means of special etching methods disclosed in polycrystalline sheets of aluminum the existence of substructures differing in orientation by small amounts (about 1/4"). Boundaries of these structures at relatively high temperatures had the remarkable property&apos; of moving about while the ordinary boundaries remained stationary. Cahn2 also observed substructures in bent and annealed single crystals of aluminum, zinc, magnesium, and rock salt. The position of subboundaries could be explained in terms of a dislocation mechanism of polygonization in which dislocations move into lines at right angles to the bent glide planes thereby relieving elastic stresses in these planes. Guinier and Tennevin8,6 disclosed the further interesting feature that polygonized structures coarsened significantly upon prolonged annealing. Somewhat similar subgrain phenomena have been observed in silicon iron of commercial purity. Although some evidence for the development of macro-mosaic structures in silicon iron already has been reported by one of the authors6,7 under the phenom-enological term "crystal recovery," much better evidence recently has been obtained due to improved etching techniques. In addition, phenomena regarding structural changes have been uncovered. The present investigation is divided into three parts: (1) The phenomenon of Laue spot sharpening on annealing cold-rolled crystals, (2) the phenomena of polygonization and subgrain coarsening The material used in the present investigation was high-grade commercial silicon iron sheet of nominal composition, 3.3 pct Si, 0.004 C, 0.011 P, 0.010 S, 0.04 Mn, 0.01 Al, 0.04 Cu, 0.01 Sn. Large single crystals of this material Were prepared for cold-rolling or bending as scheduled. Cold-rolling of 12 pct was carried out on a laboratory 8-in, diam rolling mill. The bending deformations were performed by pressing the crystals between a solid Fig. 2—lllustrative foue patterns to show Laue spot sharpening. a (Left)—Specimen as cold rolled, b (right)—After 48 hr at 1400°C. round bar and a mating half cylinder, both heavily greased. Individual specimens were cut from the deformed crystals, and the cut edges were deeply etched prior to annealing. Laue photographs were made using 40-kv tungsten radiation. The technique used to disclose the various subboundaries was an electropolish and electroetch in a bath of chrome-acetic acid.&apos; The anodic polishing done at 22 v was immediately followed by etching at a reduced voltage, which was dependent upon the nature of the subboundaries. Phenomenon of Laue Spot Sharpening on Annealing Cold-Rolled Crystals Fig. 1 gives the initial and final orientations of the specimens cold-rolled 12 pct. Each specimen was annealed at a temperature and for a time which caused significant structural changes as evidenced by alterations in Laue patterns. Representative Laue patterns and micrographs showing the essential changes are given in Figs. 2, 3, and 4. The essential points to be derived from these illustrations follow: 1. Annealing at 950°C clearly develops a substructure with the orientation of the cold-rolled specimen. 2. The subboundaries formed obviously separate regions of nearly the same orientation. Some of the subboundaries appear as a sequence of dots similar to those observed in aluminum by Lacombe and Beaujard,&apos; but whether this is due to extremely small differences in orientation is not known at present. 3. The substructure coarsens upon prolonged annealing. 4. Prolonged annealing also causes a decrease in orientation spread according to Laue spot sharpening&apos;

Jan 1, 1952

By R. E. Collom

VARIOUS chapters already written in the history of development of the North Dome of Kettleman Hills are monotonously identical in the one underlying theme of conservation of oil and gas. Discovered on Oct. 4, 1928, by Milham Exploration Co. with its wildcat Elliot No. 1, the field has been subjected to practically every modern form of produc-tion restraint in the name of conservation. The record thus far developed shows that conservation was had for a time, at a price; and that unitiza-tion must he blessed by single ownership or 100 per cent participation to be effective. In fact, incomplete unitization places a heavy handicap upon its participants in the competitive development that follows.

Jan 1, 1937

NEW MEMBER, The following list comprises the names of those persons who became members during the period Mar. 10 to Apr. 10, 1915: Members ADAMS, Louis WINFIELD, Supt., Rolling Mills, Lehigh Plant, Bethlehem Steel Co., So. Bethlehem, Pa.. ALLEN, ARTHUR WATTS, Mine Mgr Rodeo, San Juan, Argentina., BALL, EDWIN MARCOTTEL, Mine Supt., Ishkooda. Mines, Care Tenn. Coal, Iron & R. R. Co., H.F.D. 1, Birmingham, Ala. BOLN, CHARLES A., Oil salesman 135 S. 2d St., Philadelphia., Pa. BOYD, DAVID F., Naval Officer Navy Department, Washington, D. C. CAPERTON, GEORGE HENRY Charleston, W. Va. COGGESHALL, GEORGE W., Chem. Engr., Institute of Industrial Research, Washington D C

Jan 5, 1915

By F. E. Pawlek, J. K. Gerlach

The chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. In the first part of the investigations the reaction rate of the chlorides of sodium or calcium with gas mixtures of SO,-0, or SO ,-O2 ,-SO , was measured. The rate for reactions with gas mixtures SO2-O2 is ThE chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. At present the process is mainly applied to produce nonferrous metals which occur in pyrite cinders in small concentrations. Thereby the nonferrous metals are converted into water-soluble, acid-soluble, or volatile compounds whereas all the iron remains as insoluble oxide. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. The reactions occurring during the roasting process can be divided into two groups: solid-solid reaction and gas-solid reaction. The reactions between solids proceed by means of solid-state diffusion and are therefore of low velocity. The heterogeneous reactions between solids and gases of the roasting atmosphere5 are high-velocity processes and determine the velocity of the chloridizing roasting. These gas-solid reactions shall be the subject of the paper presented. In order to investigate the still little-known processes which occur during the chloridizing roasting 6-&apos; the complex reaction is split into several partial steps. First the reactions of NaCl and CaCl, with gas mixtures of SO2 and 0, have been investigated at temperatures between 500" and 600°C by measuring the weight increase of the samples. The gas mixtures used in this series of experiments had first variable compositions, then the amount of SO 2 had been increased. Furthermore the influence of Fe 2 O3 admixtures upon these reactions, the behavior of pure Fe 2 O3 with the gaseous reactants, and the chlorination of the sulfides of lead, copper, nickel, and zinc have been investigated. FORMATION OF GASEOUS CHLORINE Pyrite cinders are never completely roasted and therefore contain still a small amount of sulfide sulfur. When heated again in air, this sulfur is converted into SO,. Accordingly the formation of chlorine can first be described by the reactions: dependent on the composition of the gas phase. If more than 1 pct SO 3 is added to the roasting gas, the reaction rate is determined only by the concentrations of the SO,. In the second part the reactions between chlorine and metal sulfides are discussed. The rate of formation of gaseous chlorine is higher by me order of magnitude than is the reaction rate between ZnS and chlorine. The reaction rate of NiS and PbS lies considerably below that of ZnS. The conversion rate of both pure Fe 2 O 3 and Fe 2 O 3 containing NaCl or CaCl2 when reacting with SO2-O2, mixtures with and without SO3 portions was measured at temperatures of 500", 550°, and 600°C. The weight increase of pressings was determined by means of a spiral balanceg and the reaction rate calculated therefrom according to Eqs. [ll to [31 and [5] to [7]. The prepared samples were suspended on a platinum filament in a vertically mounted tube of mullite (ID 4 cm, length 110 cm) which could be heated by a resistance tube furnace. The platinum filament was tied to the lower end of the spiral balance. A supremax glass tube (length 70 cm) was mounted gas-tight on top of the reaction tube. The unit was sealed up at its top by a ground-in stopper which was holding the spiral balance with the sample. The spiral balance therefore hung outside the high-temperature region of the furnace. Fig. 2 shows the experimental arrangement schematically. While lowering the sample into the reaction tube pure nitrogen was flowing through the reaction zone providing a protective atmosphere. After the sample had reached the reaction temperature within approximately 1 min, the protective gas was replaced by the sulfur dioxide-oxygen reaction mixture. It took about 30 sec until the mixture filled the tube homogeneously. A Ni/NiCr thermocouple placed in the center of the furnace where the sample hung during the measure-

Jan 1, 1968

By E. Rudy, St. Windisch

The only complete phase diagram investigation of the Ti-W system is by Maykuth and coworkers,&apos; Fig. 1. Although previous work by Gonser2 indicated complete miscibility, later investigations3°5 essentially confirmed the diagram depicted in Fig. 1. The present study was undertaken because preliminary results on metal-rich ternary Ti-W-C alloys indicated complete solid solubility between 0 titanium and tungsten at temperatures above 1300°C—in contradiction to the presently accepted diagram. The powdered elements, as well as crystal bar titanium and tungsten sheet, were used in the preparation of the experimental alloys. The iodide titanium, obtained from Foote Mineral Co., Exton, Pa., had a total impurity content of less than 410 ppm, of which 150 ppm were interstitials (H, O, N, C). The overall purity of the titanium powder (Var-Lac-Oid Chemical Co., New York) was better than 99.7 pct. Major contaminants, in ppm, included: 0, 800; N, 10; H, 1500; Fe + Co + Ni + Cu + Zn, 50; C1, 200. The measured lattice parameters of the titanium were a = 2.94A and c = 4.68,A. The tungsten sheet and the tungsten powder (Wah Chang Corp., Albany, Ore.) contained the following impurities (in ppm, values in parentheses refer to the sheet tungsten): Mo, 50 (70); 0, 140 (110); Fe, 20 (60); Ni, 20 (not determined); N, 110 (not determined); sum of other impurities, <60 (<100). Samples from the iodide titanium bar stock and from tungsten sheet were prepared by repeated melting of the chipped materials in a nonconsumable electrode arc furnace under high-purity helium. The melted alloys were heavily cored, and homogeneity of the alloys could only be achieved after prolonged heat treatments at subsolidus temperatures. The majority of the alloys were therefore prepared by cold compacting the well-mixed powders in steel dies and pre-homogenizing the compacts for 6 hr at 1300°C in a tungsten-element furnace. The vacuum was better than 10"6 Torr, but for additional protection the sample container was wrapped in zirconium foil. Both preparation methods led to identical results. The measurements of the solidus temperatures were carried oat in the Pirani-type furnace described in a previous paper.6 Incipient melting in alloys containing between 20 and 90 at. pct W was rather difficult to detect visually, and therefore a photoelectric transducer system7 was employed to indicate the phase change. For the investigation of the solid-state equilibria, the specimens were first homogenized for 2 hr at slightly subsolidus temperatures in the Pirani fur- nace and then reequilibrated at, and rapidly cooled (-100°C per sec) from, the selected equilibrium temperatures. After the runs, the alloys were analyzed microscopically and by X-ray diffraction. With the exception of spot checks for oxygen and nitrogen in processed alloys, no other chemical analyses were performed. However, as the weight changes of the alloys during processing were within 0.05 pct and the lattice parameters of indeqendently prepared alloy series agreed within 0.0015A, it is reasonable to assume that no significant concentration shifts with respect to the nominal compositions had occurred. The measured solidus temperatures, shown together with literature data in Fig. 2, ascend smoothly from

Jan 1, 1969

By C. C. Mattax, J. E. Bobek, M. O. Denekas

ABSTRACT investigations in recent years have shown that rock wettability can exert a profound influence on the displacement of oil by water from oil producing reservoirs. Core analyses frequently show oil recoveries from preferentially water-wet rock to be significantly greater than those from preferentially oil-wet rock. Thus, an accurate prediction of water-drive or waterflood oil recovery is dependent on the evaluation of reservoir rock wettability. Laboratory and field studies have been undertaken to examine and develop methods which may be used to measure rock wettahililiy, to investigate factors which may alter the wettability of reservoir rock, and to determine the wettability of specific reservoirs. It has been found that measurement of the rate and volume of spontaneous imbibition of the wet-ting phase by a rock is a reliable and reproducible test for semi-quantitarive determination of preferential rock wettability. Laboratory tests have shown that the wettability of reservoir rock may depend on both the crude oil composition and the rock type. Field and laboratory tests have indicated that coring flulids and core handling techniques can cause significant changes in the wettability of rock surfaces. However, a few fluids, brine in particular, appear not to affect core wettability and may be used when coring to determine reservoir wettability. Core handling and packing procedures have been developed which preserve core wettability during storage and laboratory testing. The wetfability characteristics of six reservoirs have been evaluated by wettabilify tests performed in the field on fresh cores cut with brine or special water-base muds. The tests indicated that all six reservoirs are water wet; however, the de-gree differed from one reservoir to another. INTRODUCTION Although surface properties of reservoir rock and interfacial characteristics of rock, crude oil, and water systems have been discussed for many years, the full significance of these properties to the production of oil is still in the process of evaluation. It is known, however, that one surface characteristic—preferential wettability of the reservoir rock—-is of paramount importance when the reservoir is being produced by water-flood or water-drive mechanisms. The importance of rock wettability has been pointed out by several authors&apos;.&apos;,%* who have found that pref- erentially water-wet cores flood more efficiently than oil-wet cores; that is, more oil is recovered from water-wet cores in the early flooding stages than from oil-wet cores. Other authors&apos;," indicate that waterflood oil recovery from cores of intermediate wettability may be greater than that from either strongly water-wet or strongly oil-wet cores. These recent investigations emphasize that the true wettability of a reservoir must be known before the performance of waterflood or water-drive reservoirs can be accurately evaluated. When reservoir wettability is to be determined by core analysis, precautions must be taken to maintain the original wettability which can be altered readily during coring5 nd testing.&apos; In the coring operation the core may be partially or completely penetrated by the drilling fluid which, if it contains surface active materials, may drastically change the wettability of the core. Also, improper core handling during stcrage and testing may change its wettability because of evaporation of fluids or exposure to oxygen or surface active contaminants. One purpose of this paper is to discuss methods for obtaining, preserving, and testing cores without altering their original wettability. In addition, the results of wettability tests on fresh and preserved cores from six reservoirs are presented where special precautions were taken to obtain samples without altering their wettability during the coring operation.