Search Documents

By Jürgen Antrekowitsch

Typical zinc oxides recovered from wastes like steel mill dusts and neutral leaching residues are of a low quality because of impurities like fluorine, chlorine, lead and others. Therefore, they are not comparable to technical grade zinc oxides produced in “French” or “American Process”. Some new developments, most of them still in pilot scale, try to establish processes where higher qualities of the product should be achieved. Zinc oxides are not only supposed to be an input material for electrolytic zinc production. Far more, they should find their way into the zinc oxide market as a substitute for technical grade zinc oxides. Furthermore, a new field of application for these oxides has been investigated at the department of Nonferrous Metallurgy, University of Leoben. Because of a higher acceptance concerning different impurities in relation to zinc winning electrolyses, a use in electrolytic galvanizing shows an interesting option. Therefore, synthetic zinc oxides with different impurities were generated to study the effect of these impurities especially on the quality of the zinc layer. Typical steel sheets, as used for car bodies, were electrolytically galvanized and the resulting layer was analysed, as main impurities compounds of fluorine, chlorine, iron, lead and calcium were used for the investigations. Beside the layer quality, the current efficiency and the possible galvanizing speed were examined. The results give an indication, weather such an alternative application can be feasible from a technical and economical point of view or not. 597

Jan 1, 2008

By Liping Li

A comprehensive three-dimensional two-phase mathematical model was developed to represent a channel type reactor with intense bottom gas agitation. Tracer dispersion and particle tracing methods were used to conduct the analysis based on the solution of the Navier-Stokes equations. Different operational parameters, such is gas volume flow rate. bubbler separation aspect ratios and liquid Input flow rates, were investigated for the purpose of reactor optimization. The numerical calculations were compared with experimental results obtained at the University of Missouri and a good general agreement was observed. Relatively low longitudinal mixing was observed characterizing the system as a "plug-flow" type reactor, in contrast to the intense vertical mixing, under the conditions investigated. Some general mixing characteristics are also discussed In connection to the behavior of other metallurgical reactors.

Jan 1, 1996

By F. Mucciardi

With the increasing trend to continuous smelting and converting, granulation of copper matte is gaining prominence as a means of decoupling the smelting and converting operations. Moreover, granulation is also being seen as a possible avenue to using higher grade oxygen in converters. By feeding cold solid matte, the oxygen concentration can be increased to compensate for the lower enthalpy feed. This leads to a higher grade of SO2 in the off gas and a lower total flow rate. Current granulation technology relies on the cooling of a falling matte film by water jets. This technology while effective has several drawbacks including those related to safety. Noranda and McGill University have developed a new process (patent pending) for solidifying copper matte (or slag). It overcomes many of the negatives of current technology. The system is based on an air cooled twin roll caster. This: new system uses no water and instead incorporates heat pipe technology to transfer the heat from the solidifying matte to the cooling air to produce a thin strip of 1 to 2 mm in thickness. Testing of a prototype unit demonstrated its viability. This paper describes this newly developed, twin roll casting system that is completely waterless. The advantages of this process as well as the findings from several tests are also detailed.

Jan 1, 1999

By Donato Firrao, Giorgio Scavino, Paolo Matteis

"The fatigue behavior of two high-strength sheet steels used to produce car bodies, a dual-phase steel and a TWIP one, both with ultimate tensile strength close to 1 GPa, is investigated.Unnotched tensile specimens are fatigue tested at room temperature with constant load amplitude and zero load ratio, in order to determine their 1 million cycles fatigue limit, both in the asfabricated sheet condition and after the resistance spot welding of one small homologous sheet square onto the calibrated length of the tensile specimen. Moreover, pre-cracked compact tension specimens are tested with load ratio 0.1 to determine the Paris fatigue crack growth curve.The fatigue results are completed with crystallographic, microstructural, tensile, and fractographic examinations, and the influence of the microstructure and of the welding processes is discussed.IntroductionCar bodies are increasingly made with high-strength weldable steels, in order to reduce vehicles' weight (to save fuel and reduce air pollution) and to improve the vehicle occupant safety in case of car crash. The main mechanical requirements of these steels in service are fracture strength and energy absorption, relevant for crashes, as well as fatigue endurance, relevant for ordinary car usage. [1]Steel sheets for car-body applications are usually made by continuous casting, hot rolling, cold rolling, continuous annealing (or other continuous heat treatment), and protective coating (in some cases). The sheets are then cold formed (deep drawn) to produce car body parts. Finally, the car bodies are built by assembling several deep-drawn parts, often consisting of different steels, usually through the Resistance Spot Welding (RSW) process, whereby two or three overlapping sheets are welded by local Joule-effect heating [2].Dual-Phase (DP) steels are widely used, low alloy steels with a microstructure consisting of ferrite and martensite, obtained from a final heat treatment which consists of heating at an intercritical temperature and then quenching. [3,4]"

Jan 1, 2012

By Djalma Souza, Rubén Sánchez, Regina Maria Pinheiro, Carlos Maurício Fontes Vieira, Sergio Neves Monteiro

"This work has for objectives to characterize a waste generated in the form of sludge during the treatment of the effluent of a paper making industry and to evaluate the effect of its incorporation up to 10 wt.% on the properties of a clayey body used for brick production. For the characterization of the waste the following techniques were used: X-ray diffraction, X-ray fluorescence, differential thermal analysis and termogravimetric analysis with mass spectrometry. Specimens were prepared by uniaxial pressing at 20 MPa before firing at 750 °C. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The results showed that, in agreement with the characteristics of the waste, its recycling into red ceramic can contribute to decrease the consumption of fuel during the firing stage. However, the waste changes the physical and mechanical properties, generating a deleterious effect on the water absorption and flexural rupture strength of the ceramic.IntroductionAccording to the Brazilian Association of Pulp and Paper, in the last 10 years, the global production of paper grew 35%. Brazil produced 8,2 million tons of paper in 2004 and held the position of the seventh largest world manufacturer of pulp, with about 9,4 million tons per year [1]. The pulp and paper industry generates effluents that present problems related to their disposal, even after the treatment. Among the solid wastes generated by this industry, the main waste is the primary sludge from the effluent treatment plant (ETP).After the initial treatment the decanted solids go through a dewatering stage, generating the solid form denominated primary sludge. This sludge resembles a paper paste of dark gray color when humid, and clear gray color when dry. This primary waste is composed basically of kaolin, pulp, traces of chemical substances and water. This waste generated in the pulp and paper industry depends on the characteristics of the process and of the employed techniques. It can vary significantly from one industrial unit to another, even in the case that the final products are similar. Its composition is approximately 60% of kaolin and 40% of pulp, and these percentages can vary in some moments as a function of the process [2,3]."

Jan 1, 2008

By D. W. Collins

Several organic and inorganic substances are widely used to control deposit structure and morphology during the electroprocessing of copper. Methods for monitoring the levels of thiourea, glue and guar gum during electrorefining and electrowinning have been successfully developed under the trade names of Reatrol and CollaMat. Other instrumental methods have been developed for additives and decomposition products associated with the electroplating of copper and other metals. Generally, these methods have been found to be either insufficiently sensitive or lacking in the desired selectivity for some or all of the additives. These procedures have mostly employed DC techniques; i.e., cyclic voltammetry, Tafel analysis, etc. In this work, chronopotentiometry (CP) and AC voltammetry were used to examine the interaction of glue, guar gum, thiourea and chloride during the electroplating of copper onto a platinum electrode. In addition, the interactions between the additives have been explored. It was found that glue in pure electrolyte (H2S04 and CuS04 only) had no effect on the chronopotentiogram. Glue was only active if chloride ions were present. The addition of thiourea resulted in several different chronopotentiograms depending on the presence of either chloride or chloride and glue. Thiourea used in conjunction with glue and chloride showed a significant increase in the polarization during copper deposition when compared to the electrolyte containing only glue and chloride. The use of a modified channel electrode further increased the sensitivity of CP. The use of AC voltammetry was explored as a technique to monitor some of the additives. AC voltammograms have more spectral detail then their DC counterparts and it is possible to monitor some of the additives at very low concentrations with AC techniques.

Jan 1, 1999

By Richard D. Hangi

Process mineralogy techniques are uniquely applicable to industrial problems related to the extractive metallurgy of nickel, cobalt, and associated metals. Reflected 1ight microscopy, together with selected determinations by scanning electron microscopy-energy dispersive spectrographic analysis and electron probe microanalysis, provides the means to identify the ore minerals cobalt and nickel ores, determine the abundance of each ore mineral, assess the extent of intergrowth between the cobalt and nickel minerals and other ore and gangue minerals in the ores and concentrates, and predict the potential success of cobalt and nickel extraction by grinding, flotation, pyrometallurgical, and hydrometallurgical treatments. In addition, the extent of locking of the cobalt and nickel minerals with each other and with the gangue minerals can be directly observed by reflected light microscopy. Where ores have been treated by hydrometallurgical procedures, reflected light microscopy can serve to determine the causes of excessive leach consumption. Finally, the partitioning of cobalt and nickel between high-temperature synthetic phases produced by pyrometallurgical treatment can be precisely determined by process mineralogy techniques. Case histories from cobalt and nickel deposits illustrate the value of applied mineralogical techniques in the study of cobalt and nickel ores, beneficiation, hydrometallurgial, and pyrometallurgical products.

Jan 1, 1993

By Aurelian Buzaianu, Cristian-Aurelian Popescu, Gabriela Popescu, Petru Moldovan

"A lot of scraps result in processing of composite materials which contain metallic phases that can be recovered and used again in different field. Considering this point of view the aim of the paper was to separate and recover aluminum from aluminum matrix/graphite composites. The separation and recovery of aluminum alloy from aluminum alloy/graphite composites was done by treatment with halide molten salts. As halide salts were used flux tablets that collect the ceramic particles in dross. After dross separation, was used filtration in order to separate the aluminum matrix from the other impurities.Samples from the recovered alloy were analyzed using chemical analysis, optical and electron microscopy, as well as X-ray diffraction. The desired composition of the aluminum alloy obtained from scraps could be reached by some addition of metals to the metallic phase. From optical microscopy it was obvious that the structure of the aluminum alloy obtained after composite reclamation consists large particle of silicon, eutectic, a-Al solid solution and other phases like Fe, Si, Mg and Ni, or some compounds like CuAl2. 1. IntroductionThe research on the recycling and reclamation of metal-matrix composites (MMCs) becomes active to preserve the natural environment, as environmental requirements become stricter, to save energy, and to reduce garbage. In case of recycled aluminum alloy ingot the production energy is about 3 pct of that of the new ingot. This evidence strongly supports the necessity to recycling of aluminum alloys. Among aluminum alloys, metal matrix composites have high strength and elastic modulus, and also good were resistance. These materials have been developed to meet the demand properties which exceeds that of the ordinary materials, and to save energy."

Jan 1, 2008

By Hélio Wiebeck, Fabio J. Esper, Wildor T. Hennies, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz

"Natural rubber reinforced commonly with carbon black to produce vulcanized material, turns into a new environmentally friendly nanocomposite when carbon black is replaced by organically modified clays of Brazil. Carbon black is substance derived from the oil refining process with consequent pollution to the environment. Its substitution in this industrial process must contribute to diminish the oil derived products dependence. As the added clays are only a third in weight of the traditionally carbon black added, then, to obtain the same final volume it is necessary to add low cost neutral filler that does not damage the technological characteristics of the final material. This paper presents results using as neutral filler of this type rice husk ashes from industrial wastes. Experiences realized with this nanocomposite material show results of quality and technological characteristics similar or superior to those of the rubber made with carbon black.IntroductionTraditionally rubbers are black or a very dark color. But they can have different appearance when filler of distinct composition of the carbon black is used. The carbon black is substance derived from the oil gotten during the final phases of the mineral fuel treatment with consequent pollution of the environment. Carbon black show nanometric grain sized distribution and a depth black color, because these properties it is also used for computer printers inks production. The substitution of this substance, traditionally used as a reinforced load in the rubber production, will have to contribute in such a way to diminish the dependence of these products as to diminish the pollution of the environment. The present work shows the results of the use of another kind of mineral nanoparticulate material substituting carbon black in the production of some rubber products. This nanoparticulate material is the organic modification of smectite clay treated with some types of ammonium quaternary."

Jan 1, 2008

By D. I. Chalmers

The Brockman rare-metals and rare earth resource is located within volcanic and volcanogenic sediments of the later Proterozoic Halls Creek Group in the East Kimberley region of Western Australia. Exploration including surface trenching, percussion and diamond drilling has defined a major resource of rare-metals and heavy rare earth elements. The host&apos; is a steeply dipping ash-flow tuff, described informally as the Niobium Tuff, enriched in zirconium, hafnium, yttrium, niobium, tantalum, rare earth elements, gallium and beryllium. The mineralization is fine- grained (<20 micrometres) and is the result of alteration and re- mobilization of comparatively simple precursor minerals such as columbite and zircon by fluorine-rich deuteric solutions that were retained in the tuff following eruption. The ultra fine-grained structure of the tuff precludes mineral liberation and separation by physical methods. However, values can be converted to water soluble sulphates by reacting with concentrated sulphuric acid at 250°C. The solution containing aluminium, niobium, tantalum, zirconium, hafnium, yttrium, rare earths and gallium can then be processed to pure products in a sequence of solvent extraction and ion-exchange steps. As a result of these processing techniques, the commercial products obtainable from the resource include mixed rare earth and yttrium concentrates, zirconium-hafnium concentrate, niobium-tantalum concentrate and ceramic grade alumina. Further separation could result in high purity products suitable for ceramic and electronic applications.

Jan 1, 1992

By Ricardo Morales

Reactions between solids and a gas phase have many interesting theoretical aspects as well as technological applications. The present group had carried out experimental investigations as well as theoretical studies of a number of gas-solid reactions over the past decade and was able to derive interesting results. Studies of the decomposition of alkaline earth carbonates were carried out by thermogravimetric analyses. The experiments were carried out using thin powder beds as well as iso-statically pressed compacts with thermocouples embedded in the same. The investigations revealed the complexity of the reactions and the impact of the heat- and mass transfer aspects on the reaction kinetics. In the case of BaCO3, the kinetics of decomposition was complicated by the formation of a liquid phase. In the case of SrCO3, the reaction kinetics could be simulated by theoretical modeling. Gas-solid reactions were also employed as a versatile process tool towards the production of alloys and intermetallics involving transition elements by hydrogen reduction of complex oxides involving transition metals. Thin powder beds were employed to examine the micro-kinetics, while fluidized bed technique was utilized to produce bulk alloys. Preliminary correlations could be drawn between the thermodynamic stabilities of the oxides and the activation energies of chemical reduction steps. Adjusting the process parameters, products at nano-scale could be produced. The structural, mechanical and thermal properties were investigated in the case of these products. The potentialities of this method as a green route to produce industrially important alloys and intermetallics with unique properties are demonstrated.

Jan 1, 2006

By Anette Mueller, Thomas Schnellert, Sérgio C. Angulo

"The use of automatically sorting technique, to separate gypsum components from recycled material of processed construction and demolition waste (C&DW), is motivated by environmental and economical aspects. Only if the gypsum can be separated the aggregates can fulfill the environmental requirements and also the structural characteristics according to the standards. Furthermore, the separation of red brick can also improve the quality of the aggregates.This paper aims at analyzing the separation of gypsum components and red brick by using the color sorting technique. The impacts on the composition and the envelope density of recycled aggregates are described. Depending on the gypsum content the application of two processing stages (rougher-cleaner) can be necessary to produce aggregates with sufficiently low gypsum content. Additionally, the separation of red brick and concrete is successful. So, the color sorting may be a promising technique to upgrade the quality of mixed C&DW aggregates.IntroductionConstruction and demolition waste (C&DW) is a mixture of different materials. Such mixtures can be used only in low grade applications. If the material is used as certified material for road construction or as aggregate in concrete the concrete particles must be separated from the other building materials. This paper aims at analyzing the separation of gypsum components and red brick by optical sorting. The needed stages of sorting for getting a product quality according to the German Standards are deduced.Gypsum is a building material that is increasingly used for interior works in Germany like it is shown in figure 1 [1]. At present the content of gypsum in C&DW is estimated at about 1 %. Assessments on the basis of material streams of gypsum and concrete and their life spans show that higher gypsum contents of about 3 % must be expected in future [2]. Also in other countries the use of gypsum has grown considerably in the last decades. From the characterization of C&DW available in some cities in Brazil, 4 to 15 % of total amount of C&DW that may arrive at the recycling plant to be processed is excessively contaminated by gypsum. In one of these cities, the average content of gypsum in the C&DW before processing was as high as 2.1 % [3]."

Jan 1, 2008

By Daniel Adolfsson, Ryan Robinson, Fenwei Su, Jelena Blagojevic

"Cold bonded briquetting of steel plant by-products has proven to be a viable recycling alternative concerning technology, economy and environment in both the traditional blast furnace route and the direct reduction process. A critical parameter in cold bonded briquettes is the type and amount of binder used during production. The binder material must meet certain quality requirements concerning low and high temperature strength, chemistry and economy. Currently, SSAB Tunnplåt uses ordinary Portland cement (OPC) as binder in their cold bonded briquettes. In order to improve binder quality and possibly decrease OPC dependency, a binder feasibility study has been conducted concerning an internal by-product, ladle slag, as a supplement and/or partial substitute for OPC. Several characterization techniques have been used to study the behaviour of ladle slag, these include: XRD, XRF, SEM, glass content analysis, calorimetric analysis, particle size distribution and thermochemical stability considerations concerning the CaO-Al2O3-SiO2 system.IntroductionRecently, a project was initiated at SSAB Tunnplåt AB, in Sweden, which aimed at reducing the amount of ordinary Portland cement (OPC) as hydraulic binder in cold bonded briquettes by partly replacing it with ladle slag. OPC is traditionally used within civil engineering, and widely accepted as a hydraulic binder in a number of different applications. OPC consists of four major crystalline phases, i.e. C3S, C2S, C3A and C4AF. Tricalcium aluminate as well as the ferrite phase in OPC reacts very quickly with water, for this reason gypsum is added to the clinker in order to retard these reactions. The fact that gypsum is present in the system limits the recycling of briquettes to the BOF, since the presence of gypsum during steelmaking results in a significant amount of sulphur emissions. The latter along with the expense that follows, makes it worthwhile to consider alternatives for OPC as binder in cold bonded briquettes."

Jan 1, 2008

By Maria G. Alves, Alexandre M. Stumbo, Francisca M. A. Pinheiro, Jonas Alexandre, Sergio N. Monteiro, Valdo da S. Marques, Paulo R. N. da Silva

"Brazil is among the few countries with potential for developing all sources of renewable forms of energy. In particular, the country is leading the world efforts of substituting petroleum based fuels for biofuels, such as ethanol and biodiesel. Most of the Brazilian petroleum, which has now achieved self sufficiency, is extracted from offshore wells located at the north region of the state of Rio de Janeiro. In view of the future depletion of petroleum, the State University of the Northern Rio de Janeiro (UENF) has created a Center for Alternative Energies (NEAL) to carry out R&D programs on renewable forms of energy. Today, the main project of the NEAL/UENF is a model park for generation of renewable forms of energy. The objective of this work is to present the structural concept of the park and discuss its contribution in terms of scientific, technological, economical and environmental benefitsIntroductionEnergy is presently a key issue in the world agenda for sustained development and environmental protection. It is of common agreement that the existing status of increasing use of fossil fuels, mainly petroleum, natural gas and coal will not only cause depletion of these resources with a consequent elevation in price but also climate changes, especially global warming. In fact, the humankind may be already facing an irreversible situation of climate alterations as well as reduction of conventional sources of energy. The worse predictions foreseen by specialists, still for this coming century, are dramatic disasters due to catastrophic weather in association with a profound energetic crisis. This scenario may, however, be avoided by actions that could effectively tackle the core of the problem. These actions have been suggested and discussed by scientists and leading authorities, especially in international symposia [1-3]. In particular, the Kyoto Protocol proposed goals for reduction of greenhouse gas emissions as well as a mechanism of carbon credits to allow for decreasing CO2 content in the atmosphere without affecting industrial production [3]."

Jan 1, 2008

By Vladyslav P. Yakubovsky, Boris I. Bondarenko, Valentin A. Noskov, Vladyslav M. Sokolov

"Each of Ukrainian producers of ferronickel, stainless steel and synthetic diamonds has the same basic problem with recycling their fine Ni-containing secondary materials. The conditions for generation of them along with the correspondent properties were investigated in details. The new approaches for their recycling have been proposed. They are based on application of some pyrometallurgical processes that are used in Ukraine. The proper equipment is also available. It has been shown that the dust from laterite calcining process of ferronickel production should be efficiently recycled by sintering. The stainless steel dust should be smelted after briquetting as a charge addition to the Ni-containing discarded batteries in the elaborated furnace. The sludge after synthetic diamonds production should be pelletized and processed by liquid cast iron with application of induction magnetodynamic forces in the specific furnace.IntroductionThe object of the investigation is recycling the Ni-containing secondary fines in a form of dust and sludge. There are several generators of the fines in Ukraine. Namely they are Pobuzhye Integrated Ferronickel Mill; Electrometallurgical Works “Dneprospetsstal” with stainless steel plant as well as Poltava Diamond Plant that produces synthetic hard materials. Their businesses are the largest in the Commonwealth of Independent States (CIS). However the status of handling with the fines is not perfect since the applied recycling technologies are low efficient. The landfilling option is often adopted for them. At the same in Ukraine there are some nontraditional pyrometallurgical recycling technologies and equipment that should be tried for application in smelting these secondary materials.Recycling the sludge of synthetic diamonds productionThe sludge of “Poltava diamond plant” from production of synthetic hard materials has a following chemical composition, %: iron oxide – 29.7; chromium oxide – 18.97; nickel – 4.27; manganese oxide – 15.2; sulphate – 3.85; natrium – 14.9. The content of moisture is 70-80%. The moisture quite quickly evaporates while keeping sludge out of doors. Sludge returns into the weak agglomerates. The sizing of the dried sludge particles presents the figures from 400 to 1000 µm. The moisture was extracted by sludge pressing. The content of the basic compounds of the moisture is, g/dm3: chromium oxide – 1.6; nickel – 0.001; manganese oxide – 0.002; lead – 0.005; sulphate – 13.6; natrium – 17.0."

Jan 1, 2008

By Larry M. Southwick

The smelting of copper and other non-ferrous metals have made considerable advances over the last 125 years. Many of the ideas and processes currently in use were attempted early in the history of smelting and were unsuccessful. Often the cause was incomplete understanding of the metallurgy involved, inadequate refractories, poor materials of equipment fabrication or trying too many new ideas at once. With time, these problems get solved and the technologies become commercialized .These were processes whose time had not come when originally proposed, but did eventually. On the other hand, there have been some concepts whose time will never come. They were impossible then and they are impossible now. The people that dream these up were either crackpots (they didn&apos;t know what they were doing, but thought they did), or charlatans (they knew they didn&apos;t know what they were doing, but didn&apos;t care). Both rely on bad science to propose metallurgical absurdities. These too have their place in the development of technology, though mostly negative, and several examples will be discussed in this paper. Three from around the turn of the century will be covered, as well as one from this decade. The last demonstrates that the art of creating absurdities has not withered, even after ninety years of scientific sophistication, and some can even be patented. The first three reached field trials due to the gullibility of company management. The last arose from a fortuitous mis-operation of a plant which solved a problem, but the explanation and patent which arose are metallurgically impossible.

Jan 1, 1999

By Junji Shibata

The waste acid mixture whose main component is phosphoric acid, is discharged from the etching process in the liquid crystal production industry. In order to separate impurity acids from the phosphoric acid, trioctyl phosphate (TOP) is used as an extractant. TOP can extract acetic and nitric acids selectivity. The extraction and stripping operations are carried out for the acid mixture by beaker-scale experiments and countercurrent multistage operations with mixer-settler equipment. TOP selectively extracts the acetic and nitric acids in the acid mixture. From the results of the McCabe-Thiele analysis obtained by beaker-scale tests, the extraction for acetic and nitric acids are approximately 100%, respectively, by 6-stage extraction with a phase ratio (A/O) of 0.4. On the other hand, almost all of acetic and nitric acids are stripped with water from the organic phase by 4-stage stripping with a phase ratio (A/O) of 1.0. About 95% of acetic and 98% of nitric acids can be removed from the acid mixture without extracting phosphoric acid in case of the mixer-settler equipment operation. There are several steps such as slicing, lapping, chemical etching and mechanical polishing in the silicon wafer production process. The chemical etching step is necessary to remove any damaged layer caused in the slicing and lapping steps. The typical etching liquor is the acid mixture comprising nitric acid, acetic acid and hydrofluoric acid. The waste acid is treated by a neutralization method with a high alkali cost and balky solid residue. A solvent extraction method is applicable to separate and recover each acid. Acetic acid is first separated from the waste liquor using 2-ethlyhexyl alcohols as an extractant. Then, nitric acid is recovered using TBP (Tri-butyl phosphate). Finally hydrofluoric acid is separated with TBP solvent extraction. The expected recovered acids in this process are 2mol/L acetic acid, 6mol/L nitric acid and 6mol/L hydrofluoric acid. The yields of this process are almost 100% for acetic acid and nitric acid. On the other hand, it is important to recover and reuse the metal values contained in various industrial wastes from a viewpoint of environmental preservation. Most industrial products are made through processes to separate impurities in raw materials, solid and liquid wastes being necessarily discharged as industrial wastes. Chemical methods such as solvent extraction, ion exchange and membrane separation, and physical methods such as heavy media separation, magnetic separation and electrostatic separation are considered as the methods for separation and recovery of the metal values from the wastes. Some examples of the application of solvent extraction to the treatment of wastes such as Ni-Co alloy scrap, Sm-Co alloy scrap, fly ash and flue dust, and liquid wastes such as plating solution, the rinse solution, etching solution and pickling solution are introduced.

Jan 1, 2003

By Tomoya Nihei, Hiroshi Hayashi

"A novel selenium removal process called Recycled Green rust/Ferrite Process is developed by MMC. In this process, a mixed Fe2+-Fe3+ hydroxide compound, green rust (GR), reduces selenate to elemental selenium, while GR is consequently oxidized to magnetite Fe3O4. Sequencing batch-mode experiment showed that the residual selenium concentration gradually decreased with the number of batch test increased. Stable selenium removal was achieved when the number of batch test exceed 15 times. Optimum selenium removal ratio reached 99.95% where initial Se concentration 2.1mg/L decreased to 0.001mg/L. Furthermore, the continuous feeding test carried out through a pilot-scale plant with a feeding capacity 600 L/hr. Approximately 860-hour-feeding test was carried out for the selenium-contaminated groundwater which had an averaged selenium concentration of 0.88 mg/L. Selenium concentration in the effluent from thickener maintained less than 0.01 mg/L (selenium removal rate of 99%) until a net operating time reached 800 hours.IntroductionJapan is one of the largest producers of selenium, and thus there are potential environmental impacts of selenium on soil and aquatic environments. The Mitsubishi Material Corporation (MMC) owns some real estate properties whose soil and groundwater was polluted by selenium and other heavy metals. These sites include former industrial plants: a smelter for nonferrous metal and a fabricating semiconductors and pigments. Selenium in aquatic environment commonly exists in four oxidation states, namely, VI, IV, 0 and -II. Selenate ion (SeO4 2-), the most oxidized form of selenium, and selenite ion (SeO3 2-) are highly soluble and mobile. Elemental selenium (Se0) is insoluble in water and therefore has much lower toxicity. Because selenium is carcinogenic and teratogenic at high concentration, the national effluent standard in Japan is fixed at 0.1 mg/L and the environmental standard at 0.01 mg/L. Although there are several selenium removal techniques, the most conventional process is coprecipitation with a ferric hydroxide because of its simplicity and low cost. It is known that selenite is adsorbed strongly on the surface of ferric hydroxide, but selenate is not. The low affinity of selenate on oxide mineral surfaces was demonstrated by the fact that selenate could be easily displaced by adding competing anions, particularly sulfate ion. Selenate removal from polluted water is one of the most difficult techniques, and more effective methods are desired. MMC developed a novel selenium removal process [1]. In this process, the concentrated slurry that contains Fe(II)-Fe(III) hydroxyl-salts known as Green Rusts (GRs) contributes to selenate removal. The main components of the iron precipitate in the reactor are GRs and their oxidation product, magnetite (Fe3O4)."

Jan 1, 2008

By Guillermo A. Vidal

With the introduction of monitoring technologies, process computers and Web services on Industrial Facilities the need for electrolytic processes automation has been set. Recently designed facilities have substantially improved plant layouts, automated cathode processing and copper harvesting. Despite these advancements only limited progress has been accomplished on the electric current distribution of the process. Lately a number of proposals focused on preventing short circuits and balancing cathode currents have emerged. Among these are the AZSA intercell, the Outokumpu double contact, and the Optibar InterCell Plus. Although these intercell bars are clearly superior to the conventional bar, little or conflicting data is available about their merits relative to each other. Consequently, selection of the best intercell bar for most applications is accompanied by uncertainty, which can lead to less than optimum results. A critical evaluation of the performance of the aforementioned bars on the basis of the application is provided, thereby giving the framework and guidelines for the selection of the best bar for each application.

Jan 1, 2003

By T. A. Edison

A distinct hydrocarbon maturation anomaly coincides with the Gold Acres open pit, Nevada (Figure 1). Both atomic hydrogen to carbon (H-C) ratios and reflectance measurements of contained organic matter indicate significantly higher maturity in samples collected within the confines of the open pit than in samples from the surrounding region (not shown in Figure 1).

Jan 1, 1987