Search Documents

Power cable costs are only a small part of total mining costs. So many mine operators consider power cable failure and resultant downtime as part of the cost of doing business. But, viewed in terms of lost production, these costs can be quite significant. Now one company, Cablec, seeks to cut cable costs by upgrading the polymer compounding process used to make cable insulating and semiconducting materials. Cablec is the leading manufacturer of electrical power cables in North America. And with about a third of the market, Cablec is the largest supplier of power cable to the mining industry in the United States. To improve its products, Cable has entered the polymer compounding business. In July, it began producing insulator and semiconductor polymer compounds at its plant in Indianapolis, IN. "This new facility provides a quantum leap over conventional compounding methods," said Harry C. Schell, Cablec's president and chief executive officer. "The Cablec polymers plant is producing a dramatically higher standard of polymer compounds that provide significantly higher levels of performance and improved life cycle costs for power cable." Cablec faces tough foreign competition in the wire and cable business. Competing on price alone is difficult, particularly when foreign producers are state subsidized. So Cablec feels the best way to compete is to establish new quality production standards. The company's new polymers plant is one way to do this. By increasing purity control and uniformity in polymer compounding, Cablec says its power cables will last longer and fail less often. A typical medium voltage cable consists of a conductor, conductor shield, insulation, insulation shield, metal shield, and jacket. The conductor shield and the insulation shield are conducting polymers. Contaminants and imperfections can occur within the insulation, at the conductor shield/insulation interface, or at the insulation shield/ insulation interface. Over time, these contaminants and imperfections can decrease the electrical strength of the cable or cause premature cable failure. The effort to minimize the number and size of any possible contaminants begins with pure polymer compounds mixed in a clean facility. However, most power cable manufacturers manually handle raw materials, use ethylene/propylene (EP) in bulk bales, and mix polymercompounds in open Banbury mixers. The quality and uniformity of polymer compounds is also impacted by temperature variations in the mixing process. This results in wide gradations of product consistency from batch to batch and ultimately contributes to power cable failure. Cablec says the improved polymer compounds from its state-of-the-art plant will be the purest and most consistent insulating and semiconducting materials available. The plant itself RCA spent $18 million to build Cablec's Indianapolis plant. RCA used the facility to mix specialty polymer compounds used to make video disks. RCA had two considerations in mind for the plant, cleanliness and uniformity of the compounds. However, when the video disk market failed to materialize, RCA sold the 46.5 dam 2 (50,000 sq ft) plant to Cablec for $3.1 million. Cablec invested an additional $3 million for modifications and increased production capabilities. Today's replacement cost for such a facility is estimated at $30 million. Cablec says the plant will set a new standard for performance and be economically difficult to duplicate anywhere. One of the essential elements of the plant's clean process environment is the air intake system. It filters contaminants greater than 2 um, less than one-fiftieth the current industry standard. All material handling and conveying areas in the facility are air-locked. This keeps out contaminants such as smoke, dust, and pollen. Banks of pneumatic pumps move polymer components through the system and continually filter the air. The plant also has a backup air intake system. No process downtime due to pump failure here. From the time raw material enters the plant, it is stored, transported, and processed in filtered air by an airtight stainless steel system. The stainless steel resists rust and corrosion. This further eliminates the danger of contamination from paint or rust particles in the conveyance network. A computer system allows a single operator in a central control room to monitor every aspect of the compounding process from air quality to line speed. The computer

Jan 12, 1988

By Waclaw Trutwin

The idea of automatic or remote control of the mine ventilation process generally, and methane concentration particularly, attracts the attention of mining engineers more and more. The advantages of introducing mine ventilation control systems are breaking traditional reluctance. The change of attitude is not only because of the requirements of modern exploitation technology, but it is also due to the recent progress in development and successful introduction of reliable monitoring systems and actuators in the form of controlled ventilators and doors [1]; [2], [3], [4], [5], [6]. Many 'years of theoretical and experimental studies of the dynamics of mine ventilation processes created the needed base for a proper design of an automatic control system [7],[8],[9], [10]. From these studies must, however, be drawn a fundamental conclusion, which may be regarded as the motto of this paper: An automatic control system for mine ventilation ill-conditioned or improperly designed is capable of creating hazard situations in response to random disturbances, much more, severe in consequence than a traditional ventilation system without any automatic or remote control! This statement is easy to prove if the dynamic properties of the ventilation process are taken into consideration. The ventilation process, as a matter of fact, is described by non-linear equations, and it must be expected that the process has more than one state of equilibrium. In other words, in the ventilation process may exist not only one but also more than one steady-states of flow, of which some are stable and others unstable. In certain circumstances, there may be no steady-state at all, and the process will oscillate [8], [11] , [12] . The state of flow in a network tends towards a steady-state and the actual steady-state established will depend on the initial conditions or disturbances in flow (fire,. etc.), which steady-state from the total number that will be . We frequently observe jumps from one steady-state to another. Disturbances in flow conditions which may cause such transitions are events of random character, occurring very rarely. Concluding, it must be stressed that there has to be a control system adjusted to the ventilation process in order to avoid situations mentioned above. There is only one alternative available and suitable for examination or study of the dynamics of a given mine ventilation problem: either by continuous monitoring of the real process, or numerical simulation of the process using a mathematical model. The advantages of the second method are obvious. This method allows consideration of every possible case very quickly and cheaply in relation to the first method. The aim of the paper is to show again that the simulation of the mine ventilation process and particularly a methane concentration process, separately or combined together with a control system, are real possibilities. A simulation method requires precise specification of the problem under consideration. For example, if we intend to examine a methane-concentration control system, the following items have to be specified: - expected target function of the control system. - structure of the control system. - mathematical model of control system, including sensor system, data preparation system, controllers, decision routine, regulators, etc. - structure of mine ventilation network. - mathematical model of ventilation process, including air flow and methane concentration processes. - pattern of disturbances which may occur in the controlled process as well as initial conditions on a 'start-up' of the system. Using typical computer programs for numerical solution of equations in the mathematical model of the problem involved, we are able, within the adequacy of the model, to simulate every case specified by the disturbances and initial conditions. As a result of simulation, it is expected that the following parameters could be defined: - transient flow in the network. - transient state of methane concentration in working areas. - stability of flow and methane concent¬ration. - stability of the control system. - range of control. - efficiency of control, etc. It is obvious that simulation methods readily allow for modifications to existing systems such that desired results will be obtained. Also optimisation problems could be solved by use of the simulation methods. In order to illustrate these general thoughts, a brief presentation of a mathematical model of methane concentration and

Jan 1, 1980

By W. R. Bruce, R. W. Wittkopp, R. L. Parratt

Introduction The Relief Canyon gold deposit is about 24 km (15 miles) east of Lovelock at the south end of the Humboldt Range in northwestern Nevada. The deposit, is in the Relief-Antelope Springs mining district, which has historically produced silver, antimony, and mercury. There is, however, no mention in the literature of commercial gold production. Fluorite prospects at the gold deposit site have had no reported production. At Relief Canyon, the Late Triassic Grass Valley formation overlies and is in fault contact with the Late Triassic Natchez Pass formation. Epithermal disseminated gold mineralization is found within the various types of fault breccia between these two formations. Geology The Natchez Pass formation of Late Middle to Late Triassic age is composed of more than 300 m (985 ft) of massive gray to dark gray locally carbonaceous dolomitic limestone. Some minor beds of shale and siltstone up to 1 m (3 ft) thick are found in the project area. The limestone is locally silty or sandy. The color of this formation below the oxidation base ranges from gray to black and appears to be a function of carbon content. The Grass Valley formation of Late Triassic age is composed of more than 200 m (655 ft) of interbedded units of thinly parted argillite, hard gray to brown quartzite, siltstone, and shale. Within the oxidation zone, these units are olive gray. A few beds within this formation are slightly calcareous and a number of sections, especially those containing shale, are dolomitic. Below the oxidation zone, the quartzite beds are often slightly carbonaceous and the argillite, siltstone, and shale beds are often highly carbonaceous, giving them a black color. Two types of intrusive rocks have been recognized at the Relief Canyon deposit. Both appear to predate mineralization. Fine to moderately fine grained quartz monzonite dikes, up to 3 m (10 ft) thick, were encountered in several drill holes. In a number of intervals, these dikes have undergone either propylitic or argillic alteration. The age of these types of dikes is not known. It appears, however, that they are either Jurassic or Cretaceous. No gold mineralization has been found in this type of dike. Diabase dikes were also encountered in a number of drill holes. These dikes have almost always been propylitically altered. Although the exact age of the diabase dikes is not known, they are probably equivalent in age to the quartz monzonite dikes. Quaternary alluvium is found forming fans at the base of steep slopes and as recent fill in present day drainages. The alluvium is composed of either Natchez Pass limestone or Grass Valley quartzite and siltstone, depending on which unit served as the bedrock source. A significant portion of the Relief Canyon deposit is covered by Quaternary alluvium. Figure 1 shows a generalized geologic map of the Relief Canyon area. At the deposit's site, the Grass Valley formation appears to have been thrust over the Natchez Pass formation. The age of the thrust is probably correlatable with the Nevadan Orogeny, which gives it a Jurassic-Cretaceous age. The general strike of the thrust, referred to as the Relief Fault, is in a northwest direction. The strike of the bedding of both the Natchez Pass and Grass Valley formations roughly parallel the strike of the Relief Fault. The general dip of both the Natchez Pass and Grass Valley formations is in a southwest direction. The general dip of the Relief Fault, in the area of the Relief Canyon gold deposit, varies and has the appearance of a northeast-southeast striking anticline that plunges in a southwest direction. A small fold perpendicular to the plunge of this anticline forms a dome over the southerly portion of the Relief Canyon deposit. A number of northeast and northwest trending normal faults slightly offset the Relief Fault. Because of their small displacement, they are not shown on the generalized map. Gold Mineralization Gold mineralization occurs along the highly brecciated fault contact between the Natchez Pass and Grass Valley formations. Weak gold mineralization often occurs up to 2 m (6.5 ft) above the thrust in the Grass Valley formation. Most of the ore grade mineralization, however, is present below the Grass

Jan 11, 1984

By R. Edward Williams

The Spa1lation Process Because of the low thermal conductivity of many hard rocks, rapid heating of these rocks produces a thin surface layer in which the temperatures attain high values. Thermal expansion of this surface layer is constrained by the reminder of the still cool rock, and when stresses within the surface rock become high enough, the surface rock breaks away from the cooler rock behind it and flies or falls off as a thin flake called a spall. Then the next, newly exposed surface is heated, and the process continues. This process is the basis of spallation drilling. The hot gases from a jet burner provide the heat for spallation to occur, and their high velocity provides a scouring action that transfers heat to the rock and removes the spalls as rapidly as they form. Spallation is a process which works in very hard rock. It is dependent upon the thermal expansion coefficient and the thermal diffusivity of the rock but is also affected by any discontinuities in the rock. To date the efforts which have been made to evaluate the various rock according to their spallability has been minimal. As the success of this process is dependent upon the characteristics of rock it is expected that the study of rock mechanics will prove to be of greater value to this program than to the other mechanism for drilling and excavating rock. Commercial Uses of SPALLATION In the 19408s, the Linde Air Products Division of Union Carbide (UC 1 began developing spallation for use in mining taconite ore, which is presently the chief source of iron in the United States. In this work UC developed a jet-piercing tool that burned fuel oil with oxygen to produce spallation and contained mechanical cutters to remove rock that was not amenable to spallation. The UC jet-piercing machines have since produced about 40 million feet of shallow blast holes used for emplacing explosives in the taconite mines. During this work it was found that hole diameters could be increased by merely reducing the advance rate of the burners and that existing holes could be enlarged by making another pass through the hole with the same burner. The Browning Engineering Go. of Hanover, N.H., has developed a hand-held spallation burner to cut slots in granite. It has been used for a quarter of a century and is now standard equipment for quarrying granite throughout the world. This burner, which resembles a small jet engine oriented with its exhaust pointed downward, is the forerunner of a flame jet burner used to spall experimental holes in granite at maximum rates in excess of 100 ft/hr when operating in hard, competent granite. It uses No. 2 fuel oil, which is burned with compressed air. The system uses water to cool the burner and the exhaust gases. These gases, along with the steam produced from the cooling water, blow the spalls from the hole. Experimental Work Theoretical and experimental work has been accomplished by the Massachusetts Institute of Technology and the Los Alamos National Laboratory. This work is reported in Refs. (3) and (4). To verify the experimental results of this work laboratory scaled down field tests were conducted using two we1 1 characterized granites from quarries in Barre, VT and Westerby, RI, under defined heating conditions. In the laboratory tests a propane - oxygen heating torch was used to direct a flame at the granite surface and the spal 1 ing process was examined at various heating rates with a high-speed video taping system operated at 200 frame per second. This produced a time-lapse sequence where the onset of the spallation process was easily distinguished. Also the heat flux from the torch to a flat surface at various stand off distances and flows was measured. A similar set of tests was conducted using the more easily quantified and uniform heat source of a 1.5 kw GO2 laser. This allowed accurate

Jan 1, 1986

By Duport. P. J.

INTRODUCTION In February 1981, the Canadian Institute for Radiation Safety (CAIRS) initiated a routine Personal Alpha Dosimetry service for personnel of the Canadian uranium mining industry. This service is based on the use of the [Personal Alpha Dosimeter] developed by the French Atomic Energy Commission (CEA). The origins of personal alpha dosimetry and its rational are briefly described. Technical and organizational aspects of a routine personal alpha dosimetry service are outlined in this paper. HISTORICAL BACKGROUND International recommendations (1) and Canadian regulations have established Maximum Permissible Exposures (MPE) for each source of radiation exposure. Uranium workers in mines and mills are exposed to external radiation ( [y] rays) and to internal radiations ( [B] and [a] particles) which are delivered to the respiratory track by airborne alpha emitters (Rn and Th daughters and Long Lived Dust). To date, dosimetry for uranium workers has been performed by area monitoring/collective dosimetry. In North America the concentration of radon daughters is routinely measured by grab samples taken at the work place and by on-site gross alpha counting. The concentration of potential alpha energy is then calculated (usually by Kusnetz method) and expressed in Working Levels (WL). The time spent by each worker at a given work place is determined from his time sheets and used to calculate the individual monthly exposures to airborne alpha emitters, which is then expressed in Working Level Months (WLM). The uncertainties attached to such a procedure are obvious even in the case of frequent grab samplings and can be expected to lead to an underestimation of individual doses. Among fifteen possible sources identified in a mine situation, (2) four may stretch the standard deviation of the measurements' distribution, nine may lead to an underestimation and two may lead to either an underestimation or to an overestimation. To improve this situation, in 1971 the Atomic Energy Commission began studying the use of personal alpha dosimeters to determine individual exposures from the airborne alpha emitters encountered in the uranium industry environments. Criteria for a Personal Alpha Dosimeter In order to minimize the difficulties encountered in determining exposures received by uranium workers, the CEA in co-operation with the Atomic Energy Control Board of Canada (AECB), has developed a set of criteria for personal alpha dosimeters. Exposures may be determined easily and accurately using this criteria. Autonomy The dosimeter must operate for at least 10 to 12 hours. Excess time spent in the mine or in the facility may possibly be related to an accidental situation causing unusual levels of radioactivity. Since the dosimeter may be needed in non-underground settings where a cap lamp is not used, full autonomy is desirable. Maintenance, Periodicity of Reading In order to complement other dosimetry systems, the personal alpha dosimeter should be read monthly when the filter should also be changed. Routine air flow checks can be made according to local conditions (e.g. diesel loading). Radioisotopes Identification Since the exposure unit (WLM) is based on the concentration of potential alpha energy in the air, the personal alpha dosimeter should be capable of identifying each short lived alpha emitter included in the calculation of the WI, and WLM. Permanent Exposure Record Three points may be considered here: 1. In many countries, lung cancer in uranium workers is a compensable occupational disease. In some instances, compensation is awarded when it can be proven that the worker has received an exposure above a certain limit. The present uncertainty of the individual exposure makes the compensation procedure difficult. 2. By design, a personal alpha dosimeter must representatively sample all airborne particles, ranging in size from the unattached fraction to the upper limit of respirable aerosols (0.001 to 5 µm). The dosimeter must offer minimal resistance to the penetration of these aerosols. While the mining/ milling environment presents harsh conditions which may accidentally contaminate the dosimeter, it is important to be able to distinguish these cases of contamination and still obtain accurate readings. 3. A dependable dose register is most valuable for further epidimiological studies. The dependability of such a data base increases with the possibility of a second assessment of the dosimeters' reading (filter, film).

Jan 1, 1981

By Janet A. Johnson, T. B. Borak, K. J. Schiager

INTRODUCTION In the USA regulatory agencies have adopted standards which limit the allowable concentration of ore dust in underground uranium mines. The American Conference of Governmental Industrial Hygienists has recommended a threshold limit value for silica which has been incorporated by reference in federal regulations (30 CFR 57, 1980). The Nuclear Regulatory Commission (NRC) imposes a limit for unprocessed uranium ore dust for reducing the exposure to radioactive materials from inhalation (10 CFR 20, 1980). We have been unable to trace the origin of the NRC standard. Recently the ICRP has published recommendations concerning limits for intakes of radionuclides by workers (ICRP, 1979). We have used the ICRP methodology to compute the dose equivalent commitment to lung and bone from inhalation of insoluble ore dust particles. These values were used to derive air concentrations which would provide an acceptable risk for induction of cancer from occupational exposure. Results indicate that the new ICRP recommendations are more restrictive than the present NRC standard for radioactivity. The maximum allowable dust load in a uranium mine will depend on both the concentration of silica (% Si02) and the amount of radioactivity (% U308). We have combined these standards assuming complete independence of biological hazard to establish boundary conditions for which either silica or radioactivity is the dominating factor. Based on these results we present suggestions for analysis of ore dust to insure compliance with regulatory agencies. SILICA STANDARDS Silicosis, fibrotic lung disease produced by crystalline silica, was one of the earliest forms of occupational disease to be recognized. The pulmonary lesions caused by silica, silicotic nodules, consist of concentrically arranged bundles of collagen fibers. Fusion of these nodules results in progressive massive fibrosis causing alveolar changes which decrease ventillation and blood flow in the lungs. The current Threshold Limit Value (TLV) for mineral dusts is based on the concentration of free silica. The standard is expressed in three forms: (1) Particle count standard: TLV (mppcf) = 300/(% Si02 + 10) (mppcf = million particles per cubic foot) (2) Respirable dust mass standard: TLV (mg/m3 ) = 10/(% respirable Si02 + 2) (3) Total dust standard: TLV (mg/m3 ) = 30/(% Si02 + 3) The most commonly used form is the respirable mass standard. These curent values for silica are based primarily on epidemilogical studies of Vermont granite workers and other occupationally exposed workers. In the Vermont study no cases of silicosis were seen in individuals employed after dust control measures were initiated and whose subsequent exposure averaged less than 5 mppcf. The free silica concentration in the airborne dust to which these workers were exposed averaged 25%. A concentration of 10 mppcf of granite dust is considered equivalent to 0.1 mg/m3 quartz. The current respirable mass standard allows a maximum silica concentration of 0.1 mg/m3. NIOSH (1974) has recommended a reduction in the current TLV for respirable silica to 0.05 mg/m3 Si02. As with radiation standards, the TLV for mineral dusts is an upper limit for time weighted average exposure. It is recommended that dust concentrations be maintained as far below the TLV as current practices permit. RADIATION STANDARDS The present concentration limit for airborne natural uranium in ore dust prior to chemical separation is 75 µg of uranium per m3 of air ( 10 CFR 20, 1980) . This corresponds to 1.85 Bq/m3 (50 pCi/m3 ) of natural uranium, U-238, U-235 and U-234 and is equivalent to 3.7 Bq/m3 (100 pCi/m3 ) of gross alpha activity with radioactive equilibrium between the long-lived alpha progeny through Ra-226. The origin or basis for this standard is not known, but it presumably includes both chemical toxicity and risk from somatic radiation injury. Recently the International Commission on Radiological Protection (ICRP, 1977) has published recommendations concerning the objectives and criteria for limiting radiation exposures. This was followed b y a revision of the limits for intake of radionuclides by workers (ICRP, 1979; ICRP, 1980). The previous compilation of limits for internal emitters was published by ICRP Committee II in 1959 (ICRP, 1959). The latest version includes new methodlogy outlined in ICRP Publication 26 (ICRP, 1977) as well as extensive metabolic information

Jan 1, 1981

By R. E. Le Messurier

GENERAL DESCRIPTION The mines are located at Broken Hill in the western part of New South Wales, Australia, 930 km west¬northwest of Sydney. Mining Methods Where pillars must be left between stopes, extraction of a block of ore between two or more levels is carried out in stages: 1) Stopes are mined overhand by horizontal cut¬and-fill stoping, or by long-hole stoping. The various methods of horizontal cut-and-fill stoping used are desig¬nated as: -Loader cut-and-fill stoping with horizontal blast¬holes and diesel load-haul-dump (LHD) units. -Open stoping with horizontal blastholes and com¬pressed air or electric scrapers, or with diesel or electric LHD units. Square-set timber stoping, where ground condition precludes open stoping. The backs are sup¬ported with timber square sets. Pattern rockbolting of the backs may be used as an intermediate stage between open stoping and square-set stoping. 2) Vertical pillars are mined by undercut-and-fill stoping or by vertical crater retreat stoping. 3) Where a horizontal pillar has been formed below the level above the primary stope, this level pillar, usually 6.1 to 8.2 m in depth, may be mined by over¬hand square-set stoping or by undercut-and-fill. Long-hole stoping is used at the Zinc Corp. (ZC) and New Broken Hill Consolidated (NBHC) to mine parts of the zinc-rich A and B lodes. Drilling is carried out from drill drives and, in some cases, sills. Hole sizes used are 165 mm (61/2 in.), 110 mm (4'h in.), and 65 mm (21/2 in.) nominal diam with hole lengths being limited to 50, 30, and 20 m respectively. Ammonium nitrate-fuel oil (ANFO) and water gel explosives are used. Broken ore is loaded from drawpoints at the bottom of the stope using rubber-tired diesel-driven LHD units which deliver ore to an orepass. Annual production at Zinc Corp. and NBHC accord¬ing to mining method is given in Table 1. At Zinc Corp. mining is being carried out at depths varying between 200 and 832 m. At NBHC it ranges from 528 to 915 m below the surface. The average travel time to the stope is 30 to 45 min. GENERAL ORE BODY REQUIREMENTS Size, Shape, and Dip There are six separate lodes which carry minable ore in the mines of Zinc Corp. and New Broken Hill Consolidated. The lowest of these and the main ore bodies presently being mined at Zinc Corp. are the lead lodes, consisting of a siliceous fluoritic ore body (No. 3 lens) and overlying it a calcite rhodonitic ore body (No. 2 lens). Each possesses characteristic ratios of lead, silver, and zinc, although the grade within each lens is variable, in places being as high as 30% Pb. There are also low¬grade portions which consist chiefly of poorly mineral¬ized rhodonitic material. No. 3 lens terminates within the Zinc Corp. leases, while No. 2 lens continues into the NBHC leases where it continues to provide a significant proportion of pro¬duction from the mine. Overlying the No. 2 lens are the various zinc-rich ore bodies. In ascending sequence these are lower No. 1 lens, upper No. 1 lens, A lode, and B lode. A typical assay for the small No. 1 lens group ore bodies is 8% lead, 50 g/t silver, and 20% zinc. The `A' lode is a large low-grade ore body in which the higher grade sections assay 4% lead, 30 g/t silver, and 10% zinc; larger quantities of lower grade ma¬terial also occur. B lode, the main zinc lode, typically assays 5% lead, 30 g/t silver, and 17% zinc. B lode increases in size as it extends south, and in NBHC is a major ore body, contributing about 52% of the production. All the lodes pitch south, the average pitch being 0.52 rad (30°) in the Zinc Corp. leases and rather flatter than this in the NBHC leases (see Figs. 1-3). The ground is all competent rock. Production requirements at Zinc Corp. are 900 000 t and 1 200 000 at NBHC.

Jan 1, 1982

By Bob Snashall

Introduction 1300 BC, Egypt. Pharaoh, the god-king, owned all things. He was the only mine operator. As the provider of all things, Pharaoh had great expectations of his officials who gathered the wealth. Pharaoh's official, the mine foreman, was at a gold mine site to see that royal expectations were met. For the official, it could mean a promotion to the good life here and to the godly life hereafter. When he checked the haul for sufficient progress, a lot was at stake. The miner wore a loincloth, perhaps a headband and, if he was a prisoner, ankle manacles. Only an oil lamp helped illuminate the hot, dusty blackness. A fire at the base of the quartz ore face competed for scarce air. The ore so heated crumbled at the prompting of copper wedges. Confined to a crouch, the miner tossed chunks of ore onto a rope-mesh which, when loaded, was drawn up and lugged out. On the surface, the gold was ground to dust. Then it was transported by donkey caravan to the royal depot. There it was weighed, recorded, and distributed to workshops. Many minerals mined Egypt had gold mines to the south in Nubia and to the east in the desert and Sinai. Indeed, gold underwrote Egypt's prosperity. With a constant gold supply, fewer hungry hands robbed burial crypts and tombs. Gold was sacred, "the flesh of the gods." The shiny metal financed the army that policed the desert mining routes and guarded the gold caravans from Bedouin marauders. Gold theft was an offense to the gods. Anyone caught with gold `in his lunchpail,' so to speak, could say goodbye to life, both in this world and the next. In addition to gold, Egypt possessed other mined riches that allowed the Egyptian civilization to flourish. From Sinai and Nubia came copper. So abundant was the red metal that it enabled Egypt to become the supreme power, before the advent of iron. Also mined were amethyst, turquoise, feldspar, jasper, carnelian, and garnet. These were used for the rich inlay work that distinguished Egyptian jewelry and cloisonne. But Egypt's most endurable and awesome material was its stonework - for statues and obelisks and in temples, tombs, and pyramids. Stone quarrying was a vast enterprise. One expedition boasted nearly 10,000 men. These included 5000 laborer soldiers, 130 skilled quarrymen and stonecutters, and - egads! - even 20 scribes. In addition, there were thousands of officials, priests, and officers grooms. There were even fishermen, to provide the multitudes with the catch of the day. Mining methods detailed In 1300 BC, quarrying techniques had changed little since the age of the pyramids some 1300 years before. At that time, in 2600 BC, limestone was locally quarried and fashioned into the blocks of the pyramids. A basic limestone mining method was tunnel quarrying. A ramp was built up to the face of a cliff. A monkey stage was then erected on a ramp. While standing on the stage, quarrymen carved out a rectangular niche in the cliff. The niche was large enough for a quarryman to crawl into. With a wooden mallet, he hammered long copper chisels along the edges of the niche floor to free up the back and sides of the block. The quarryman climbed out of the niche and removed the stage. He then carved out a series of holes in the cliff face for what would be the bottom of the block. The quarryman pounded wooden wedges into the holes. He watered the wedges until they were soaked. The water-logged wedges expanded, splitting the stone along the line of holes. The freed-up block was then levered down from the cliff. On the ground, the blocks were placed on sledges. Men pulled these to nearby water transport. Without block and tackle pulleys, paved roads, and wheels, this was no mean feat. Each block weighed an average of 2.3 t (2.5 st). Whenever possible, the quarrying was done directly from the surface. This "open cast" quarrying also involved using chisels

Jan 2, 1987

By E. C. Ekedahl, R. J. Heath

Introduction Potassium, together with nitrogen and phosphorous, is an essential nutrient required for growth. Since all living things need potash, the major demand for potash - about 95% of the total - is as a fertilizer. Agricultural productivity has increased dramatically in recent times. This increase in crop yields requires substantial amounts of added nutrients to keep the soil fertile. It follows then that potash will always be in demand. There is no substitute. Other fertilizers that contain phosphorous (P) and nitrogen (N) are complementary and not competing products. Fireplace ashes (pot-ashes) have a relatively high potassium content. Their value as a fertilizer had been recognized for centuries. But today's potash industry did not begin until deposits of potassium-rich ore were discovered and exploited in Europe during the 19th century. Canadian potash development Potash in Saskatchewan was first recognized in 1943. It was discovered as a byproduct of an oil exploration program. But it was several years later before the existence of a major commercial deposit was acknowledged, and not until 1951 that the first attempt at development occurred. That attempt was unsuccessful. The shaft flooded and was abandoned. It did, however, demonstrate the need for new technology to penetrate the waterlogged Blairmore layer. This was eventually developed and the first mines were brought into production in the early 1960s. Once the technology was available, and the extent and quality of the potash beds became known, a number of companies proceeded to develop mines. By 1970, seven mines were in operation and three more were nearing completion. Combined, total capacity then was 7.6 Mt/a (8.4 mil¬lion stpy) K20. At that time, world potash consumption was about 15 Mt/a (16.5 million stpy). This increase in supply from Canada produced a large potential surplus that shattered the prevailing balance between supply and demand. Although world demand increased steadily throughout the 1960s and early 1970s, it was several years before world supply and demand were again in balance. Saskatchewan capacity has been expanded a number of times. It now stands at 10.7 Mt/a (11.7 million stpy) K20. Actual production has not approached this figure, however. Two new mines in New Brunswick have recently been built with a combined annual capacity of 1.2 Mt (1.3 million st) K20. Total Canadian capacity of about 12 Mt/a (13 million stpy) now amounts to 30% of world capacity. Central offshore marketing organization Canadian Potash Exports Ltd. (Canpotex) was created in 1970 as the offshore marketing organization for Canadian producers. Canpotex is owned by Saskatchewan producers and is their exclusive marketing organization for offshore business. Each company handles its own sales in Canada and the US, but all sales to other markets are handled through and by Canpotex. The Saskatchewan industry has an ore body of a size and consistency unmatched anywhere in the world. Large efficient mines have production costs that compare favorably with other producing countries. On the minus side, Saskatchewan is remote from most major markets. It therefore needs the ef¬ficiencies that stem from one organization that coordinates all offshore shipments and minimizes distribution costs. Agriculture guides potash market In the period following World War II, potash was a classic growth industry. World demand increased each year from 1945 to early 1970s. Since then, demand has been more erratic. Some years show substantial increases, but are followed by significant declines. For about the last decade, the pattern has been unclear and future demand has become correspondingly difficult to predict. North America and Europe together account for about 40% of the world potash consumption. In both areas, farming is characterized by surplus production, declining crop prices, and expensive government support programs. Under those circumstances, farmers respond by minimizing input costs. Fertilizer is one of the items they reduce. Potash is retained in the soil. It is possible to reduce potash application with no immediate deterioration in crop yield. The lower yields occur only when potash levels are depleted. So, farmers can econo-

Jan 12, 1987

By Dennis S. Kostick

Introduction Soda ash is known chemically as sodium carbonate, an important inorganic chemical. It has been produced for several centuries by processing certain vegetation and minerals. The US soda ash industry has evolved from several small sodium carbonate mining operations in the West. Now, a nucleus of six companies produce about one-fourth of the world's annual soda ash output US producers currently dominate the world market. But certain international events are occurring that will reshape the domestic soda ash industry in the next decade. Historical perspective Soda ash is used mainly in the manufacture of glass, soap, dyes and pigments, textiles, and other chemical preparations. All of these are the first basic consumer products produced by developing societies. About 3500 BC, the Egyptians became the first society to use crude soda ash. The soda ash was used to make glass containers. It was most likely obtained from dried mineral incrustations around alkaline lakes. Soda deposits were virtually nonexistent in western Europe. So people resorted to burning seaweed to obtain the ashes. The ashes were then leached with hot water and the solute was recovered after evaporating the solution to dryness. The solute, a crude "soda ash" was impure. But, it could be used to make glass and soap. These two products and industries were important to the population and economic growth of the region. About 11.5 t (13 st) of seaweed ash was required to produce about 0.9 t (1 st) of soda ash. Along the coasts of England, France, and Spain, seaweeds with varying alkali contents became important items of commerce and sources of soda ash before the 18th century. The LeBlanc process used salt, sulfuric acid, coal, and limestone. It became the major method of production from about 1823 to 1885. In the early 1860s, Ernest and Alfred Solvay, two Belgian brothers, successfully commercialized an ammonia-soda process to synthesize soda ash. It used salt, coke, limestone, and ammonia. The Solvay process produced a better quality product than the LeBlanc method. In 1879, Oswald J. Heinrich presented to the Baltimore meeting of AIME, a paper entitled "The manufacture of soda by the ammonia process." The paper compared the two processes and foretold the demise of the LeBlanc technique. World production of soda ash in 1880 was 680 kt (750,000 st). Of that, 544 kt (600,000 st) was produced by the LeBlanc process. Of the 2.8 Mt (3.1 million st) of soda ash produced worldwide in 1913, only about 50 kt (55,000 st) was by the LeBlanc method. The LeBlanc process was never used successfully in the US, except for a brief period from July 1884 to January 1885 in Laramie, WY. Previously, soda ash had been produced by burning certain plants, as exemplified by the early Jamestown colonists, or by recovering small quantities of natural sodium carbonate found in alkaline lakes, such as those found near Fallon, NV, and Independence Rock, WY. Before the 1884 startup of the first synthetic soda ash plant in the US at Syracuse, NY, most of the domestic soda ash demand in the East was met by imports, primarily from England. Large-scale commercial production of natural soda ash began in California in 1887 from surface crystalline material at Owens Lake. Production from sodium carbonate-bearing brines at Searles Lake began in 1927 (Fig. 1). In 1938, during exploration for oil and gas in southwestern Wyoming, a massive buried trona deposit, presumably the world's largest, was accidentally discovered. Recent mineral resource evaluation by the US Geological Survey and the US Bureau of Mines indicates that the Wyoming trona deposit contains 86 Gt (93 billion st) of identified trona resource in beds 1.2 m (4 ft) thick or greater. Additionally, there is about 61 Gt (67 billion st) of reserve base trona. Of this 36 Gt (40 billion st) is in halite-free trona beds and 24 Gt (27 billion st) is in mixed trona and halite beds. In 1953, the Food Machinery and Chemical Corp. (later shortened to FMC Corp.) became the first company to mine trona in Wyoming. Soda ash demand increased.

Jan 10, 1985

L.R. Bower In regard to the paper by J.B. Gwiazda, it makes a highly technical approach to show that the µ factor used by designers of lemniscate-guided roof supports has never really been confirmed as a maximum and assumes that convergence is vertical. Also, the paper does not appear to take into account deflection of structures, which occurs when the lemniscate and base members are fully loaded to their maximum stress level, nor the front to back line of the support in relation to differential roof to floor movements caused by strata movements under pressure. It is not unusual for differential movements to be slightly diagonal to the line of the support, particularly in faulted areas and on gradient faces. The paper also does not take into account consolidation of fines immediately above and below the support. Generally speaking, any differential movement is from face to waste and under these conditions the µ of 0.3, which appears to be an international standard, has worked in practice. However, if the face end of the support is lower than the waste end, then the µ of 0.3 can be considerably increased, giving rise to the damage mentioned in the paper. The ideal design should aim for a slightly forward bias in the lemniscate guide so that the last increment of setting is toward the face, tending to close any fissures that may have developed during the support advance cycle. The support should also be fitted with positive set valves to ensure that a high setting load density is attained to minimize bed separation. As far as powered supports are concerned, convergence is irresistible and all powered supports converge at their rated yield load. A similar principle can be applied to the differential roof to floor movements to drastically reduce the very high forces that would otherwise be applied to the lemniscate structures and pins and that, in turn, are transferred to the base arrangement and floor loading. Any differential movements are usually catered for by the 0.3 µ factor or deflection of structures in the lemniscate guide arrangement and consolidation of the floor. The floor loading, due to differential movement, is in addition to the support convergence load and requires additional bearing area to avoid possible floor penetration. Some seven years ago, Fletcher Sutcliffe Wild Ltd. (FSW) introduced a lemniscate-guided shield support where the lemniscate linkage is connected to the roof bar through two horizontally converging rams to allow differential movement to take place above a given rated figure. This is a known force and can be guarded against, whereas with rigid connections the forces, as yet, are unconfirmed. By careful design, a horizontal force in excess of 6 MN (60 tons) opposes differential movements for a total ram loading of only 2.5 MN (25 tons), or 1.25 MN (12% tons) each. This principle can considerably reduce the length and weight of the support in comparison with a rigid pin-type structure ; also, the yield load rating can be increased without affecting the lemniscate forces. The graph shows the tensile and compressive forces in a lemniscate linkage of a support with and without hydrostore. These forces react into both the roof beam and base members and, as can be seen from the support height to linkage load graph, a considerable reduction in these reactions is gained by the use of the FSW patented hydrostore system. Floor loading is considerably reduced under maximum µ conditions, and by allowing the roof bar to move with the strata, some degree of improvement to strata control is achieved in line with the assumptions in the paper. In practice, these movements have only been in the region of a few millimeters, which, in turn, reflects on the improvements to strata control by the addition of positive set valves. Supports to this design of both 450- and 280-t (496-and 309-st) rating have been successfully used in the United Kingdom for several years, negotiating many faulted areas without one single reported need for repair or maintenance. This includes supports left unattended during the year-long strike, proving the reliability of the system.

Jan 8, 1986

By Mark A. Krall, Robert L. Geddes, James C. Frost

Introduction The Conda Partnership's Dry Valley phosphate mine is a thinly bedded, multiple seam open-pit mining operation where selective mining techniques are used to recover phosphatic shales. The mining methods used are truck/shovel and scraper/dozer operations. Ore is shipped 32 km (20 miles) by rail to a beneficiation facility. The ore is upgraded by washing and calcining. The mine and beneficiation complexes are owned by the Conda partnership. It is a joint venture between Beker Industries Corp., of Greenwich, CT, and Western Co-Operative Fertilizers (US) Inc., of Alberta, Canada. The Partnership operates as a separate entity of the two partners. The Dry Valley mine is located 48 km (30 miles) northeast of Soda Springs in Caribou County in southeastern Idaho. The mine is situated on the Caribou National Forest. Mining operations take place between 2 and 2.4 km (6400 and 7900 ft) in elevation. It is accessible partly by 32 km (20 miles) of paved roads and 16 km (10 miles) of dirt roads. The winters are long and severe, and the summers are short and mild. This article describes the history, geology, exploration, mining, and reclamation that makes this mine Idaho's largest producing mine and the western US' leading phosphate producer. History and production In the mid-1950s, Western Fertilizers of Salt Lake City, UT, drove an exploratory drift in Maybe Canyon. A large bulk sample of phosphatic shales was analyzed for phosphate content and processing characteristics. No large scale mining or processing operations were undertaken. In the late 1950s, the Dry Valley property was sold to Central Farmers of Chicago, IL. No major operations took place. In 1964, Central Farmers sold the property to El Paso Products Co. of Odessa, TX. El Paso Products supervised the mining operations of Wells Cargo Mining Co. from 1965 through 1967. During this time, El Paso Products built a beneficiation facility and a fertilizer complex in Conda. A 32-km (20-mile) railroad was also constructed from the mine to this facility. From 1968 through 1972, the mine was shut down due to a depressed fertilizer market. In 1972, El Paso products sold its ore reserves, beneficiation plant, and fertilizer complex to Beker Industries Corp. In 1979, Beker Industries sold 50% of its ore reserves and 50% of its beneficiation plant to Western Co-Operative Fertilizers (US) Inc., of Alberta Canada, forming the Conda Partnership. It has operated the mine and beneficiation plant since January 1979. From the mid-1950s to the mid-1960s, no substantial production took place. From 1965 to 1967, El Paso Products stripped 3 Mm3 (4 million cu yd) and mined 2.3 Mt (2.5 million st). From 1972 through 1983, 50 Mm3 (66 million cu yd) were stripped and 18 Mt (20 mil¬lion st) were mined. Geology The Wells Formation forms high ridges and hillsides in the Dry Valley area. It is best exposed along the west face of Dry Ridge. It forms the imposing wall on the east side of Dry Valley. The formation is divided into two members. The lower member, about 213 m (700 ft) thick, is dominantly thin to medium-bedded limestone and silty limestone. It contains nodules and stringers of chert and minor sandstone. The upper member is composed principally of thick-bedded to massive cross-bedded, light-gray to orange-yellow, fine grained sandstone. There is some interbedded brown to light-gray limestone. This member varies from 369 to 457 m (1300 to 1500 ft). Recent investigations indicate that the upper Wells is of Permian age. Under some conditions, the Wells may be water-bearing. Otherwise, it has no apparent economic significance. Grandeur Member (Park City Formation) Overlying the Wells Formation is a distinctive light-gray to white dolomitic fossiliferous limestone. This unit has been identified by the US Geological Survey (USGS) as the Grandeur Tongue Member of the Park City Formation. This member is sometimes absent due to its contact with the Meade Peak Member of the Phosphoria Formation. It is easily detectable by its color, hardness, and fetid odor. Phosphoria Formation The Phosphoria Formation of Permian age was named from Phosphoria Gulch, Bear Lake County. The formation has been studied extensively and developed for its economically valuable phosphate reserves.

Jan 11, 1985

By Andrew N. Peterson

US mine operators frequently fail to investigate more cost effective and productive bulk material handling systems because surface mines seem to lend themselves to truck ore haulage. In this country, as a result, use of conveyors to move heavy loads from mine to process facilities has been minimized, if not actually neglected. In contrast, there are more than 50 conveyorized surface mines in successful operation around the world. These mine operators have learned that properly applied conveyorized systems can offer major savings in capital and operating costs, which contribute to improved profits when combined with other proven mining technologies. Growing acceptance and application of conveyorized bulk material handling in surface mines also points up how unique each mine is and how careful planning contributes to maximum mine effectiveness. Because of these differences, mining executives and technical and operating staffs need to develop an understanding of three factors in applying conveyorized bulk material handling in surface mines: • Why each mine will benefit from the type of automation permitted by conveyorized operation, •What kind of equipment is available, and • What applications most effectively demonstrate the first two factors in action - hauling either ore or waste. The conveyorized systems considered in this presentation have production rates from 0.5-2.7 kt/h (500-3,000 stph). Worldwide, these systems have been operating since the early 1960s. Advantages of Conveyors Why do you want conveyorized bulk material handling? First, it almost always provides lower operating and maintenance costs. Second, it frequently requires lower initial capital costs and almost always requires lower capital costs over the life of the surface mine. Third, it provides comparable operating availability, and finally, it frequently gives comparable operating flexibility - depending on the mine plan. Cost avoidance can be accomplished with modern production methods. These, in turn, permit increased productivity and reduced operating costs such as those for energy, maintenance, and manpower. It has been demonstrated in European surface mines and elsewhere, that conveyor systems frequently require lower initial costs than does truck haulage. Almost always such operations require lower capital costs over the mine life. Those costs include the continual addition of haulage trucks to both accommodate the increasingly difficult haulage routes and fulfill replacement requirements when trucks wear out. Conveyor systems handling ore in numerous large crushing and port facilities, which have operated since the early 1950s, have clearly demonstrated a useful conveyor life of more than 25 years. In contrast, off-highway trucks have life spans of six to eight years. The following examples illustrate comparative capital costs to purchase conveyor systems and comparable truck haulage units. Example 1 The ore haulage route from point A to point B is level and 610m (2,000 ft) long. The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be transported at a rate of 1.8 kt/h (2,000 stph). The installed capital costs to provide a properly designed conveyor that will transport the described material from point A to B is about $450,000. The capital cost to purchase three 77-t (85-st) off-highway trucks and one spare truck - which would provide equivalent capacity - would be about $1.2 million. The truck cost estimate is based on a 6 min. or 771 kt/h (850 stph) truck cycle time. Truck efficiency is estimated at 0.8. Each 77-t (85-st) truck would have an actual haulage rate of 617 kt/h (680 stph). Therefore, three trucks would be necessary to transport the designated tonnage of 1.8 kt/h (2,000 stph). A movable crushing plant would be located at point A for the conveyors and a permanent crushing plant at point B for the truck haulage system. Capital costs for these primary crushing plants were not included in the calculations for either system because the capital costs are frequently comparable. Example 2 The transport route from point A to point B is 610 m (2,000 ft) horizontally and 122 m (400 ft) vertically - on a 20% grade (Fig. 1). The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be moved at a rate of 1.8 kt/h (2,000 stph).

Jan 6, 1983

By Jonathan Ludlow, Robert A. Jankowksi

Introduction A longwall operator can make few changes to increase output, significantly reduce respirable dust, and decrease power consumption. Reducing drum speed, and thereby cutting with increased pick penetration, is one. This article defines the benefits of deep cutting in terms of reduced dust production and power consumption. It also identifies the practical aspects of high pick penetration in terms of shearer performance and coal loading. Before examining some practical aspects of reducing drum speed and looking at the theoretical background, it is worthwhile to summarize what is meant by high penetration and deep cutting, and what potential benefits and pitfalls may be expected. Deep cutting (in the sense of high penetration rather than wide web) can be defined in one or more of the following ways: • Cutting with an average pick penetration distance higher than that used in the past. • Cutting with a pick penetration higher than the longwall operator would have used if the advantages of deep and slow cutting were not considered. • Cutting with a well-designed shearer drum below 40 rpm. All these definitions are slightly arbitrary. They are given to provide a basis for discussion and to make the point that any move towards deeper, more efficient cutting can result in operational benefits. The benefits of deep cutting appear in many different areas. The most noticeable benefit, provided suitable instruments are available, is the reduction of airborne respirable dust. During an experiment on a longwall in the Pittsburgh seam, a nearly four to one reduction in dust levels was seen when drum speed was halved. Not all studies have shown such a big reduction, but it seems that some benefit is almost always obtained when drum speed is reduced. Production rate and specific power consumption are also affected (in a positive sense) by reducing drum speed or increasing pick penetration. Although these changes may not be as spectacular as those in dust level, they contribute to the economic return of the longwall operation. Similarly, improved washability through fines reduction may have a beneficial economic effect. Cutting with shearer drums operating at lower speeds does have some possible deleterious impacts that an operator should be aware of. For example, cutting reactions - loads imposed on the picks by the coal being cut - will be increased as a deeper cut is used. Steps must, therefore, be taken to ensure the stability of the shearer and provide an adequate haulage effort. These increased cutting reactions also result in higher loads on the power transmission system (gearboxes, ranging arms, pick boxes, etc.) from the shearer motor(s) to the pick tip. These higher loads must be anticipated and provided for with the necessary hardware. In particular, extra haulage power must be provided with low drum speeds, since haulage effort required increases roughly in proportion with pick penetration. Because the drum will be rotating more slowly or will have fewer picks, the load on shearer components will also be more variable. If suitable, robust equipment is not used, this increased vibration will decrease reliability. Benefits of Deep Cutting Lower dust levels, decreased specific power consumption, and improved product washability are the most noticeable benefits of reduced drum speeds. Although the benefits will vary greatly with mining conditions and the type of coal, some examples of what can be expected are described below. Reduced Dust Levels Figure 1 shows principal results of a study on the effects of reduced drum speed conducted on a longwall in the Pittsburgh seam (Ludlow, 1981). This figure shows that average dust production was reduced by about 70% when drum speed was halved. By making some assumptions about such quantities as coal density, it is possible to apply this proportional reduction to the quantity of respirable dust liberated per ton of coal mined. When this is done, two kinds of results are obtained: • At 70 rpm, about 1 g (15 gr) of airborne respirable dust is created for every ton mined (roughly one part per million). At 35 rpm, only 0.28-0.37 g/t (3.9-5.1 gr per st) of coal mined become airborne respirable dust. • At 35 rpm, nearly four times the amount of coal may be mined before the compliance level is exceeded, compared with 70 rpm.

Jan 3, 1984

By Edward Burris, Terry Gorsuch, Joseph M. Hans

INTRODUCTION In any large earth-moving operation, good planning and management are necessary to complete the operational tasks promptly and successfully. When an earth moving operation is complicated by radioactive contaminants, normal earth moving techniques and procedures must be modified. Any planning and management, therefore, must include the radiological aspects of the operation. It was found that the radiological aspects dominated most of the planning and management activities and were extended to all facets of the decontamination work at the former Shiprock uranium millsite. These planning aspects are discussed and their use to develop a work plan is described. The management aspects are discussed and their use to establish a management structure are also presented. PLANNING Some method of procedure, formulated beforehand, was necessary to govern the decontamination work at the former Shiprock uranium millsite. This procedure was expressed in the form of a work plan which served several listed purposes. 1. It defined the work to be done and the sequence it would follow. 2. It was used as a yardstick to measure progress. 3. It was used to assign organizational responsibilities. Several factors were considered to aid in the development of the plan. These factors are discussed below: Goals It was established that radiation exposure was occurring to persons working at the millsite, and in an around the community of Shiprock, from airborne radioactive mill wastes and radon-222 exhaling from the tailings piles. The goal set for the decontamination work was to reduce on-site exposures to levels acceptable for the millsite occupants. The attainment of this goal would also have a substantial impact in reducing off-site exposures. The objectives necessary to achieve the goal were consolidation and containment of the wastes. The former objective implies decontamination of the millsite and environs, and the later implies stabilization of the wastes. In practice, a total and complete decontamination of the millsite and contaminated environs would be very difficult and costly. The costs for decontaminating them could be high enough that an alternative method might be more cost-effective for reducing human exposures (i.e, move the affected people away from the source). The interim guide "Radiological Criteria for the Decontamination of Inactive Uranium Millsites" was used for the decontamination criteria (EPA 74). Briefly, the criteria state that off-pile decontamination should be effective enough to reduce the net above ground exposure rate to less than 10 [u]R/hr for unrestricted use of the affected area. When decontamination cannot readily be achieved, the exposure rate levels could be relaxed to 40 [u]R/hr; however, the affected area has to be restricted. The second objective, waste containment, means isolating the wastes from the biosphere. Since no method of containment was available at the beginning of the millsite decontamination effort, temporary containment (interim stabilzation) became the objective. The tailings pile and decontamination wastes would be covered with clean fill. The interim stabilization should last from 5 to 10 years until the final disposition of the wastes will occur. The goal, therefore, would be achieved by decontaminating the off-pile areas to less than 10 uR/hr where practical. The decontamination wastes would be used to plate the surface of the tailings pile and would be covered with clean fill. Radiological Survey The radiologial survey is the key factor for planning a decontamination activity. The survey should delineate the spread and depth of the contaminants relative to the decontamination criteria. Surface wastes, in general, can be evaluated for spread and depth with reasonable radiation survey equipment. Subsurface wastes on the other hand can be missed entirely, as happened during the radiation survey at the Shiprock site, although numerous exploration holes were bored and dug. The survey results can be used to define areas that may not be amenable to decontamination because of complications or safety reasons. For example, no decontamination of the bluff base was to be attempted because of the possibility the bluff might collapse on the personnel and equipment. Contaminated bottoms of decant ponds on the flood plain were not removed because they would be slurried by ground water. Slurry removal was deemed inefficient because the contaminants would be scattered and no equipment was available for its transport. In summary, the radiological survey defines the boundaries of the decontamination work and provides

Jan 1, 1981

By Gregory R. Wessel

Sulfur is a nonmetallic element widely distributed in nature and of great physical and economic importance. It is the 14th most abundant element in the Earth's crust (0.06%) and an important constituent of animal and plant life. Sulfur has been known and used since ancient times for a number of medicinal and industrial uses. At present, most sulfur is used to generate sulfuric acid that is used in a wide variety of industrial processes, particularly the production of fertilizer. Because of this, sulfuric acid (and hence sulfur) consumption is often regarded as a good index of a nation's industrial development. In the past, sulfur was mined from surface occurrences in several geologic environments, and was used in relatively small amounts. With time, the uses of sulfur and sulfuric acid expanded, as has the need for larger quantities of these commodities. Sulfur is now mined from both surface and underground deposits, and is recovered as a byproduct from a number of industrial processes. Despite valiant efforts and years of work by sulfur explorationists and others, many aspects of sulfur mineralization remain controversial. Almost as controversial is the spelling of the word sulfur. The English spelling sulphur commonly is used outside America and in the American sulfur mining industry, but sulfur is the correct American spelling as approved by the American Chemical Society, the American Geological Institute, and many others. Those new to the American sulfur industry often find it puzzling to be reprimanded for using the correct American spelling. Sulfur resources are abundant and widespread, but the extent to which they can be classified as reserves is constrained by pre- vailing prices and extraction technologies. At present, sulfur can be economically mined from very few deposits. The sulfur industry is roughly divisible into two sectors: voluntary (or discretionary) and involuntary (or nondiscretionary). In voluntary production, the mining of sulfur or pyrites is the sole objective, and the recovery of the resource is as complete as economic conditions will allow. During involuntary production, sulfur or sulfuric acid (termed recovered sulfur) are produced as byproducts, and the quantity of the output is dictated by the demand for the primary product. Voluntary sulfur now accounts for only about 35% of the elemental sulfur produced worldwide, and most inves- tigators believe that voluntary sulfur will be less important in the future. Sulfur sources and products are described as follows (after Barker, 1983): Sulfur Sources: Combined sulfur-sulfur that occurs in nature combined with other elements, commonly referring to sulfides and sulfates. Cupriferous pyrites-pyrite containing minor amounts of cop- per sulfides. Hydrogen sulfide-a toxic gas that occurs in petroleum and natural gas. Involuntary sulfur-sulfur produced as a byproduct in response to legislative or process mandates. Native sulfur-naturally occurring elemental sulfur. Nonferrous metal sulfides-opper, lead, zinc, nickel, and molybdenum sulfides that are processed for their metal content. Organic sulfur complex organic sulfur compounds that occur in petroleum, coal, oil shale, and tar sands. Pyrites-iron sulfide minerals that include pyrite, marcasite, and pyrrhotite. Sulfate sulfur-sulfur contained in anhydrite and gypsum. Voluntary sulfur-sulfur produced in response to market demand. Basic Sulfur Products: Acid sludge-contaminated sulfuric acid usually returned to acid plants for reconstitution. Brimstone-synonymous with crude sulfur. Bright sulfur-crude sulfur free of discoloring impurities and bright yellow in color. Broken sulfur-solid crude sulfur crushed to -8 in. Byproduct sulfuric acid-sulfuric acid produced as a byproduct of a metallurgical or industrial process, generally relating to combined sulfur sources. Crude sulfur-commercial nomenclature for elemental sulfur. Dark sulfur-crude sulfur discolored by minor quantities of hydrocarbons, ranging up to 0.3% carbon content. Elemental sulfur-processed sulfur in the elemental form produced from native sulfur or combined sulfur sources, generally with a minimum sulfur content of 99.5%. Formed sulfur-elemental sulfur cast or pressed into particular shapes to enhance handling and to suppress dust generation and moisture retention. Frasch sulfur-elemental sulfur produced from native sulfur sources by the Frasch mining process. Liquid sulfur-synonymous with molten sulfur. Liquid sulfur dioxide-purified sulfur dioxide compressed to the liquid phase. Molten sulfur-crude sulfur in the molten state. Prilled sulfur-solid crude sulfur in the form of pellets produced by cooling molten sulfur in air or water. Recovered sulfur-elemental sulfur produced from combined sulfur sources (including byproduct hydrogen sulfide, but sometimes referring only to sulfur from fossil fuels) by any method. Slated sulfur-solid crude sulfur in the form of slate-like lumps, produced by allowing molten sulfur to solidify on a moving belt. Specialty sulfur-prepared or refined grades of elemental sulfur that include amorphous, colloidal, flowers, precipitated, wettable, flour, and paste sulfur. Sulfur ore-unprocessed ore containing native sulfur.

Jan 1, 1994

By M. L. Harris

Explosions in underground mines and surface facilities such as processing plants are caused by confined accumulations of combustible dust and/or flammable gas mixed with air in the presence of an ignition source. Underground explosions can be prevented by minimizing methane concentrations through methane drainage and ventilation, by adding sufficient rock dust to inert the coal dust, and by eliminating ignition sources. The effectiveness of rock dust in arresting explosion propagation was proven by experiment and practice (1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11). The precise mechanism by which rock dust (generally pulverized limestone dust) quenches flame has not been fully explained, but is believed to be absorption of thermal energy from the heated gases and absorption of radiant energy, which reduces the preheating of unburned coal particles ahead of the flame front. One measurable aspect of explosibility is incombustible content. In order to determine whether enough rock dust is applied, 30 CFR1 § 75.403, Maintenance of Incombustible Content of Rock Dust, requires at least 80% incombustible content on the roof, ribs, and floor of underground coal mines. 30 CFR § 75.403-1 further defines the incombustible content as follows: ?Moisture contained in the combined coal dust, rock dust and other dusts shall be considered as a part of the incombustible content of such mixture.? In order to determine the incombustible content of the mine dust, samples of deposited dust from specified areas in a mine must be collected, analyzed, and then compared with the minimum standard of 80%. The traditional low temperature ashing (LTA) approach to determine if a coal and rock dust mixture is compliant with the inerting requirement consumes the coal dust and considers the remaining material to be inert. Compliance with the law is then determined by comparing the measured percentage of inert material of the representative band sample with the pre-established requirement of 80%. The incombustible content of the sample includes rock dust, the amount of moisture as received at the lab, and the inherent ash in the coal. The LTA method is not itself a direct measure of explosibility but is a surrogate that calculates a single parameter associated with large-scale Bruceton Experimental Mine (BEM) explosion test results conducted with dry rock dust. This method assumes a homogenous mixture with no layering of rock dust and coal dust. Float coal dust is a serious explosion hazard if it accumulates on top of the rock dust and is not mixed with the rock dust (12). Mitchell and Nagy (13) studied the effectiveness of water as an inerting agent for the coal dust explosion hazard. The study emphasized that surface water evaporates readily from dusts. Thus, in a passageway where the dust is wet, changes in weather or the ventilation system could dry the dust and make it unsafe in a relatively short period of time. Where adequate rock dust has been applied, this drying effect is not a factor. However, if the mine depends upon the moisture content as part of the incombustible content, fluctuations in the dust surface moisture within a mine can render moisture content an ineffective and inconsistent measure of safety. Additionally, if sufficient moisture is absorbed and subsequently relinquished by rock dust, a cake can form and render the rock dust ineffectual. The trend has long been recognized that mine explosions occur primarily during the winter season when the humidity is low for long periods of time (14, 15, 16). In light of this trend and due to the potential variability of the moisture content of the dust, it may not be prudent to include variable surface moisture in the total incombustible content of the sample. Instead, surface moisture should be viewed as an additional safety measure as long as the rock dust is dispersible. However, moisture limits the ability of the rock dust to disperse and can significantly reduce its capacity to effectively inert propagating explosions (2, 13, 17, 18, 19, 20, 21, 22). Given the methods by which the as-received moisture and incombustible content are determined, dust samples from the 2010 MSHA database were assessed to determine the variability of the moisture content throughout a year and how often the measured as-received moisture might have affected the dust explosibility determination if removed. The findings were then verified by observation in laboratory studies and within the NIOSH OMSHR Safety Research Coal Mine (SRCM).

Feb 23, 2014

By Earle Faig

Earle Faig Along with other transportation modes, the barge industry will be greatly affected by trends in domestic coal production. Traditionally, coal has been one of the major commodities moved by barge. Now, because of events in the international energy market, coal is finally getting the recognition it deserves as a major component of the country's energy program. Perhaps even more significantly, a series of events has caused other countries to turn to the United States as a source of coal. Although the outlook for coal demand is optimistic, it will be greatly influenced by the ability of the transportation sector to handle the additional traffic. Because of its long experience in moving large quantities of coal, the barging industry is in an excellent position to capitalize on coal's increased popularity. A brief description of the barging industry should facilitate the discussion of coal as it relates to that industry. Barge companies operate on a river system that is over 40 Mm (25,000 miles) long. It includes the East and West Coasts and the Mississippi River System comprised by the Allegheny, Monongahela, Kanawha, Ohio, Illinois, Missouri, Tennessee, Cumberland, Arkansas, Warrior-Tombigbee, and Mobile Rivers, and some smaller tributaries. The Gulf Intracoastal Waterway stretching along the Gulf Coast from Brownsville, TX, to Apalachicola, FL, also is considered part of the inland waterway system. Approximately 1,800 companies operate on the inland river system and have a combined fleet of about 4,400 towboats and 28,000 barges. The fleet of towboats represents 4.8 GW (6.4 million hp) of power. The towboats comprising this fleet vary in size from a small harbor boat to a large line haul boat with 7.5 MW (10,000 hp) of power. The choice of size and power of the boat depends on a number of factors, including the size of the river and operational constraints, such as lock size, river-current rate, and water level. The choice also depends on the tow size. A single tow on a river capable of locking through 15 barges at a time handles up to almost 20 kt (22,000 st), whereas a tow on the lower Mississippi, which has no locks, can accommodate up to 41 kt (45,000 st) of cargo. Because the quality of coal is not typically damaged by exposure to the elements, it is usually moved in open hopper barges, although covered barges are used occasionally. The most frequently used size is the jumbo barge that measures 59 m (195 ft) long by 11 m (35 ft) wide by 4 m (12 ft) deep and can handle up to 1.4 kt (1,500 st) of coal. Advantages of Barge Transportation Barging offers several inherent advantages in transportation of bulk commodities like coal. First, barges can carry large quantities of product. A single jumbo hopper barge can handle 1.4 kt (1,500 st) of cargo while it takes 15 91-t (100-st) capacity rail cars or 57 trucks hauling 24 t (26 st) each to move an equivalent amount of cargo. Thus, barges can move more tonnage with less equipment than competing forms of transportation. Second, barging offers the most fuel efficient means of transportation. Less energy is required to push a load over water than to pull a similar load over land. The amount of pollution attributable to barge traffic is minimal because barges consume less fuel. Third, barging is an inexpensive form of transportation. The inland waterway industry transports about 12% of the nation's freight for about 2% of the total freight bill. This can be attributed to competition between the large number of companies on the river system and competition with other transportation modes. Fourth, barging is an environmentally safe method of transportation. Inland river routes expose fewer urban areas to hazardous substances than rail or truck. And barge spills occur less frequently than rail or truck spills. The industry does pose some disadvantages. The waterway system is constrained by the natural river network, so barges cannot travel on the most direct straight-line route. This means that barging is usually an incomplete form of transportation requiring interface with truck or rail. The industry's market is limited to those geographical areas that are located on or near the rivers. In addition, it is a time-consuming transportation mode, making it impractical for many types of commodities.

Jan 10, 1982

General. Data for the operating information given in the 15 tables in this chapter was obtained from voluminous questionnaires sent to over 100 operating companies in 1972. There has been a considera¬ble change since then in supply and power costs and many companies have had expansions or revisions since that time, so it must be realized that information is valid for the year 1972. This is true except for the three new properties of Sacaton, Metcalf, and Pinto Valley. These three operations started up since 1972 and all information for them was obtained in 1975. The questionnaires were sent to all major copper properties throughout the world as well as to many smaller units and to some mines that had complex or unusual conditions. Properties for which no information is given did not submit completed questionnaires. Several operations were unable to supply information requested be¬cause of company policy prohibiting it. However, data is presented for 75 different operating properties. The reference number of the left-hand column is the same for all 15 tables of data. If the company had several operating properties as of 1972, then subsequent properties use the same number but a different letter. For example, Anaconda's property at Butte, Mont., is IA, whereas Anaconda's (now Anamax) Twin Buttes property in Arizona is IB. Table I gives general data for the properties including exact loca¬tion, milling rate, pertinent assay values and recoveries, and a brief listing of ore and gangue minerals. It was not possible to obtain any more information from the properties in Chile except that given in Table I. Crushing. Crushing plant operating data is given in Table 2. This table gives data on the crushers, feeders, and screens used at each property. The data obtained on feeders was confusing, but, rather than completely eliminate this information, it was decided to report it as given. The confusion lies only in the description of where the feeder is located. Where a primary feeder is listed it was not possible to determine if this feeder was on primary feed or primary discharge. For secondary feeders it is known that the feeder listed usually is feeding the secondary crushers, but at some properties it is handling the secondary crusher discharge. The same reasoning holds true for tertiary feeders-they handle either tertiary feed or discharge. This table contains a voluminous amount of data. A column giving tons per day per square foot of screen area would have been very informative, but some properties included circulating load in the feed rate and others listed new feed only, so calculations were meaningless. Autogenous Mills. The use of autogenous or semiautogenous mills for any property must be given serious consideration in the future. Table 3 lists data for four properties that are fully autogenous and four more semiautogenous mills that use balls to supplement the chunks of ore. This method of grinding is especially applicable when the ore is of such a nature that crushing problems would be severe, such as when ore is wet or sticky or contains a lot of fines. Paradoxically, it should also be considered when ore is tough and hard and blocky because then the competency of the ore means it can serve well as the grinding media. Where the ore varies greatly in hardness, as at Cyprus Pima and Lornex, semiautogenous grinding has been especially beneficial with capital costs and operating costs both 10-20% lower than could be obtained with conventional crushing and grinding. Rod Mills. For a great many years the standard milling operation used two- or three-stage crushing followed by open circuit rod mills and then ball mills in closed circuit with classifiers of some kind. A surprising number of properties crush to the fine size of about 3/8 in. and then use ball mills only, in closed circuit, with no rod mills. It is difficult to say whether rod mill-ball mill circuits or ball mill only is the best. One can be certain of two things: (1) the argument will go on for a long time and (2) for some mills one method obviously was superior over the other. As ball mills of 14, 15 ft, and larger came into use, more properties like Duval Sierrita (16b ft diam by 19 ft long) and Bougainville (18 x 21 ft) were built with single-stage ball mill grinding. Although there are larger rod mills used, especially in the iron ore industry, the largest rod mills on copper ore are at Twin Buttes (14 x 18.5 ft) and at Gibraltar (13'A x 20 ft). Table 4 lists operating data for rod mills. If a company is listed in Table I

Jan 1, 1985

By L. H. Munson, D. E. Hadlock, L. F. Munson, R. L. Gilchrist, P. D. Robinson

All uranium mills are required to perform sampling and analysis for radioactive particulates in their gaseous effluent streams and in the environment. Pacific Northwest Laboratory was requested by the U.S. Nuclear Regulatory Commission (NRC) to provide technical assistance to them for their Uranium Mill Health Physics Appraisal Program. In conducting appraisals, air sampling methods used at NRC-licensed mills were reviewed and several deficiencies noted. This paper includes only environmental and effluent particulate sampling although much of the information is applicable to both in-plant and environmental samples. First, the components of a proper sampling program are discussed: program objectives, program design, sampler design, analyses, quality assurance, and data handling. Then the specific deficiencies, or the "pitfalls" from the first 8 mill appraisals are discussed. The first consideration in establishing an air sampling program is defining the objectives of the program. What is air sampling suppose to accomplish? Many of the deficiencies we have observed have resulted because the desired objectives were not clearly established in the minds of the radiation safety staff. PROGRAM OBJECTIVES An environmental air sampling program ought to fulfill the following seven objectives. The first is to: 1) [demonstrate regulatory compliance]. Although a goal of most programs, regulatory compliance, is not well understood. One has not only to comply with the conditions of the source materials licensee, but one must also demonstrate compliance with 10CFR20 and 40CFR190. For example, 10CFR20.106 states: "A licensee shall not possess, use, or transfer licensed material so as to release to an unrestricted area radioactive material in concentrations which exceed the limits specified in Appendix B, Table II of this part .... For purposes of this section, concentrations may be averaged over a period not greater than one year." Even if a mill's license does not require sampling at the site boundary of maximum concentration, a sample may be necessary to demonstrate compliance with 10CFR20. Most mill personnel are painfully familiar with 40CFRl90.10, which states: "Operations.... shall be conducted in such a manner as to provide reasonable assurance that: (a) The annual dose equivalent does not exceed 25 millirems to the whole body.... of any member of the public as the result of exposures to planned discharges of radioactive materials, radon and its daughters excepted... from uranium fuel cycle operations..." This means a licensee's sampling program must give "reasonable assurance" that the member of the general public receiving in the most exposure gets no more than 25 millirems per year. The sampling program necessary to provide that assurance may or may not be a license requirement. However, merely meeting the license requirements and the explicit regulatory requirements does not necessariarly ensure an adequate effluent and environmental air sampling program. The second objective of the environmental air sampling program, is to 2) [identify the source(s) of contaminants]. This will include not only the routine program, but special sampling for verification of sources and nonsources. Only after sampling can a mill operator be assured that roof vents, laboratory hoods, and other localized ventilation systems are not making a significant contribution to environmental releases. An environmental sampling program should also allow the mill operator to fulfill the third objective, to 3) [estimate exposures]. Even before 40CFR190, a sampling program should have provided the mill operator with the information necessary to determine the dose to the "fence post" person, or at least to determine if doses were well below the 10CFR20 limits previously allowed. The program should 4) [detect and measure unplanned releases]. If there is a fire, a scrubber failure, or if a drum of yellowcake breaks open, measured releases will almost always be lower than conservative estimates. Whether or not a system to provide sampling during accidents is needed is almost always a cost-benefit decision. In general, uranium operations do not sample just in case an accident may occur. Yet they may decide on continuous air sampling in lieu of intermittant sampling partially because of the potential for accidents. Another objective of air sampling is 5) [to provide information on the effectiveness of control systems]. This is always a concern with new or modified equipment and may dictate sampling frequency in other situations as well. For instance, if a small leak in a bag filter cannot be detected by other means, then more frequent stack sampling may be indicated. A routine effluent and environmental monitoring program should also fulfill the sixth objective,

Jan 1, 1981