Search Documents

By Ellsworth R. Spencer

An assessment of U.S. western hardrock miners? noise exposures was conducted as part of a multi-year National Institute for Occupational Safety and Health (NIOSH) survey of noise exposures in each sector of the mining industry. Noise from selected mining equipment and operator noise exposures were measured, analyzed and tabulated for dissemination to the participating sites and are being used to direct NIOSH research and interventions to address the greatest noise hazards. Eighty-two noise dosimeter measurements were obtained, along with time-motion studies as the miners operated hardrock mining machines. Of the operators, 96% had daily noise doses that exceeded the U.S. Mine Safety and Health Administration?s (MSHA) permissible exposure level. The average gold miner dosages while operating the following equipment were: haul trucks - 261%, load-haul-dumps (LHDs) - 235%, single boom drills - 221%, bolters - 214% and dual boom drills - 163%. The worst exposure level was a silver miner with a daily dose of 873%. Time-motion data showed that this miner?s exposure accumulated most rapidly while operating a jackleg drill. These results will be used to help prioritize noise control development by NIOSH and other partners.

Jan 3, 2010

By A. Yu. Lein, V. V. Maslennikov, S. P. Maslennikova, I. Y. u. Melekestseva, Yu. A. Bogdanov

Tellurium is a high-tech and also toxic element. This element shows sufficient contents in Fe-Mn crusts and nodules in the modern ocean to be involved in future industrial processes [Hein et al., 2003]. Tellurium minerals and contents are not well recorded in modern and ancient black smoker systems. Tellurides are rarely found in sulfides from the modern oceans [Iizasa et al. 1992; Maslennikov et al., 2010]. The previous common opinion that tellurium is scarce in active seafloor hydrothermal systems can be revised due to the recent discovery of abundant tellurides in chimneys from Brothers Volcano vent site [Berkenbosch et al., 2012]. We found abundant tellurobismuthite, hessite, and native tellurium in chimneys from Su Su Knoll vents sites (West Pacific). So, tellurides can be found in some chimneys but absent in others. The causes of this are poorly understood. These conflicting data create numerous questions and require an explanation. The problem can be resolved by research at different scales including analysis of relevant genetic features of host sequences, systematic textural and paragenetic studies of different types of chimneys, and their rare mineral assemblages. Paragenetic models, compositional analyses and ranges of tellurium-bearing minerals and the physicochemical interpretation of chimney diversity in different types of VMS deposits are the main subjects of our research. The data on tellurides in chimneys from ancient VMS deposits should also be useful to resolve this problem.

Sep 1, 2014

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By Colin Barratt

The East Side Access (ESA) project is the largest underground rail infrastructure project under construction in New York City, USA. The Manhattan segment of the project is to be mined through rock and consists of 4.1 miles of Tunnel Boring Machine tunnels for track work and mined excavations to house rail switches, air plenums, and other rail facilities. This paper considers different methods for concrete lining, such as the use of fixed forms, adjustable forms, and pneumatically applied shotcrete. The advantages and disadvantages of these methods are discussed and the basis for considering one over the other are illustrated. Further discussions on design development and preparation of documents to facilitate quality and constructability in the field are presented.

By Zach Ahinga, Mike McRae, Dave Hopkins, Steve Klein

The San Vicente Pipeline project involves the construction of an 8-1/2 foot diameter water pipeline in an 11 mile long tunnel in San Diego, California. The tunnel will be excavated in extremely variable geologic conditions consisting of strong granitic and metamorphic rocks, weak sedimentary rocks, abrasive conglomerates, and mixed face conditions. This paper discusses the challenging geologic conditions and some of the key design evaluations for the project. Currently design work for the project has been completed and construction will be underway by mid-2005.

Jan 1, 2005

By D. R. Brox, J. Levell

The Montana Tunnels Mine was mined out to a depth of 900 feet at the end of 1999. The first signs of instability were recognized in 1996 along the upper slope area of the northwest sector when the pit was mined out to a depth of approximately 500 feet. To extend the life of mining operations, it has been proposed to extend and steepen the northwest highwall to a depth of 1000 feet. Slope stability analyses were carried out using the UDEC software program to assess the stability and deformation of the proposed highwall design. Back analysis of an instability in 1997 along the upper slope section and highwall deformation to date has indicated reasonable agreement with the observed mode of failure and displacement monitoring results. The results of detailed analyses of the proposed highwall design have indicated very limited additional deformation, further development of tension cracks is unlikely and large-scale instability is not expected to occur. A total of 40% of additional mining has been completed and ongoing displacement monitoring to date has confirmed very limited additional movement and no further tension crack development.

Jan 1, 2001

By P. R. Clifford

Phosphogypsum is a byproduct of the manufacture phosphoric acid. There are approximately one billion tons of phosphogypsum stored in stacks in northern and central Florida. The Florida Institute of Phosphate Research (FIPR) is investigating potential uses of phosphogypsum. These include using phosphogypsum as a road base material, as a soil amendment in agriculture, as a daily cover in landfills, and as a construction material. The results of this research will be presented and will be discussed in light of regulatory barriers to the use of phosphogypsum.

Jan 1, 2002

By Michael V. Mergentime, Prakash M. Donde

The Nutley Quarry Trunk Sewer Project is a good example of a tunnel that went through difficult and complex ground. The 2 m (7ft.) diameter and 840 m (2,750 ft.)long tunnel passed through soft ground, mixed face, and hard sandstone. The soft ground and mixed face tunneling provided several challenges. During excavation of the tunnel, the Contractor encountered a number of unanticipated large boulders. In addition, the length of the mixed face portion of the tunnel increased by 100%. The Contractor tried various construction techniques to overcome the difficult ground conditions and complete the project. The tunneling progress was slower than expected. The Contractor claimed extra costs for differing site conditions. Through discussions and negotiations between the Contractor, Engineer, and Owner, all of the changed condition claims were settled before the construction of the project was completed. This paper addresses the difficult ground conditions, claims evaluation, and how they were resolved by cooperative efforts between the Contractor and the Owner/Engineer.

Jan 1, 2001

By V. Galla

Waste rock facilities (WRF) generally have a large footprint depending on the strip ratio the mine plan provides. Considerable planning is involved during the initial phase of the mine plan regarding the location of the WRF. As the mining operations are commenced the locations of the WRF change accordingly with the variations in the mine plan involving feedback and support from local communities and stakeholders. Waste rock facilities management becomes challenging when the area available for placement is limited due to terrain topography, environmental and permitting constraints. Risks associated in the design of waste rock facilities constitute particle size of rock, chemistry associated with the rock for reactivity and stability of the over all facility. This paper will provide some insights on designing, scheduling and managing a WRF. Emphasis on geotechnical, geophysics and geochemistry aspects of waste rock with reference to design, construction process and scheduling of WRF are also presented. Design improvements in the reclamation slope of WRF for erosion control will be discussed. Continuous improvement (CI) methodology will be introduced in the process of WRF operations. Current practices and future recommendations towards sustainability and consistency in operating WRF will be discussed in conclusion.

Jan 1, 2011

By S. M. Flaherty, R. E. Scheffel, A. Guzman

Geochemical conditions within a leaching operation are heterogeneous. This variability arises mainly from hydrological controls imparted by physical characteristics of the ore and by heterogeneous metallurgical properties at the rock-fragment and industrial heap scale. The resulting chemical conditions are responsible for stratified mineral recovery, non-uniform extraction and prolonged leach cycles. This paper presents field data from a sulfide-leaching operation which clearly demonstrate the impact of chemical heterogeneity on metal recovery and the potential use of modern measuring techniques to facilitate operational monitoring and decision making for optimization of leaching operations.

Jan 1, 2006

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By Tim O’Neil

Upbeat, surprisingly so, might describe the mood at the2002 SME Annual Meeting and Exhibit in Phoenix, AZ. More than 4,000 mineral professionals gathered for three days of education, networking and product perusal. The Annual Meeting featured the theme, “Minerals for the Future@ SME” at the Feb. 25-27 gathering. Meeting attendance reached 4,039along with 479 exhibit booths show-casing 325 companies. Exhibitors found a good mix of industry types:37% from mining, 19% from processing, 20% from manufacturing and 28% from environment, education and government.

Jan 1, 2002

By Timothy P. Smirnoff

Sustaining the region?s mobility needs, achieving projected economic growth, and maintain Midtown Manhattan as a center of regional, national and global importance has led to continued investment in commuter rail and transit infrastructure in New York City and resulted in design and construction of large underground caverns. The current plans for stations in Manhattan include New York Penn Station Expansion (NYPSE) caverns for Trans Hudson Express (THE) Tunnel Project for New Jersey Transit (NJ Transit) and the Port Authority of New York and New Jersey (PANYNJ), Metropolitan Transportation Authority Capital Construction Long Island Railroad (MTACC/LIRR) twin caverns for East Side Access (ESA) Project, and station caverns of the No. 7 Line Subway Extension Project and Second Avenue Subway Project for Metropolitan Transportation Authority Capital Construction/New York City Transit (MTACC/NYCT). This paper provides a general overview of these large caverns now in design or construction in Manhattan, the area?s geologic setting, the geotechnical factors considered and approaches commonly applied for cavern design.

By J. Kang

To obtain microbial cultures with the ability to efficiently leach copper ion from chalcopyrite, microbial samples from acid mine drainage sites were mixed and then subjected to mutation using sodium nitrite (NaNO2), diethyl sulfate (DES), ultraviolet light (UV) and their combinations. Mixed cultures with a much stronger ability to leach copper ion (identified as mixed cultures A, B, C, D and E) were obtained by screening on leaching media. Leaching tests showed that mixed culture E had the best leaching performance and increased the Cu2+ content by 120.5% in 20 days, compared to a control without mutation treatment. Mixed culture E grows well on Leathen leaching medium supplemented with Cu2+ (at a final concentration of 32 g/L), reaching 3.2 × 107 cells/L after 15 days, while the unmutated control culture cannot survive beyond 15 days, indicating that mixed culture E is more tolerant of high concentrations of Cu2+. In addition, continuous leaching by mixed culture E is very effective at a pulp density of 1%. These results suggest that it has the potential for industrial applications.

Jan 1, 2008

By Tim O’Neil

The search for precious metals opened up the American West. And Nevada was right in the heart of this development. In the mid-19th century, prospectors seeking gold roamed the hills of Nevada and discovered the ComstockLode. The development of this huge silver and gold deposit began in1859 and was responsible for Nevada’s early entry to statehood. Mining was Nevada’s first industry. In more recent years, the Nevada mining industry has led the nation in gold, silver and barite production. Nevada also produces many other minerals. These include aggregates, clays, copper, diatomite, dolomite, gypsum, lime and limestone, lithium and magnesium compounds, perlite, salt and silica. Even today, Nevada’s mining industry continues to be a major economic force in the state. The mining industry has made more than $10 billion in capital investments in Nevada since 1985. And the value of Nevada’s mineral production last year was about $2.7 billion.

Jan 1, 2000

By John Heter

An alum/sulfur deposit (USDA organic registered) was mined underground for alunite (K,Na) Al3 (SO4)2 (OH)6 from the early 1900s to the 1930s. It is now being mined as an open pit quarry. A larger assemblage of minerals is included with this method (Alunite, Potassium?Alum, Jarosite, Gypsum, Native Sulfur and K-feldspar). This assemblage of minerals provides the necessary requirements as a Volcanic Soil Conditioner Sulfur-Potash. Heart of Nature? Company has been marketing this product to farmers on the west coast as a (1) pH reducer, (2) soluble sulfur and potassium source for plant growth and (3) soluble calcium. Recently, a new market has been tapped. This product has been found to solve many odor, bacteria and algae problems faced in the dairy industry.

Jan 1, 2008

By Clay Haynes

In 2005, Black & Veatch Corporation began designing a raw water conveyance system for San Luis Obispo County from Lake Nacimiento to the city of San Luis Obispo. The first element of the water transfer system will be a raw water pump station and lake tap. The wet well of the pump station will consist of a concrete lined shaft approximately 180 feet deep constructed in the very incompetent sandstone of the Vacqueros Formation. The lake will be wet tapped at approximately 172 feet below grade using a slurry earth pressure balance tunnel boring machine. The 48 to 72-inch finished diameter microtunnel will be approximately 500 feet in length. Construction is scheduled to begin in the winter of 2007.

Jan 1, 2008

By Thomas Gregor, Brian Garrod

As the popularity of precast concrete segmental linings for tunnels is growing in North America, some problems related to grouting of, and near, these linings are starting to appear. The installation of a segmental lining behind a TBM requires that the annular space around the lining be quickly filled with grout to prevent collapse of the ground. In practice, the filling of the annulus is frequently delayed and takes place a distance behind the machine typically via grout ports centrally located in the segments. If partial collapse of the annulus has occurred, it may become necessary to use higher grouting pressures in an attempt to distribute the grout. There have been several occasions where these increased pressures have caused damage to the tunnel linings. Similarly, compaction grouting adjacent to a tunnel lining can cause damage. This paper quantifies the effects of such grouting on a typical precast lining.

Jan 1, 2005

By P. Ashayer, J. Curran

Introduction Rockfalls occur when rocks or boulders detach from mountains or hills and tumble down. They can pose significant hazards to infrastructure such as highways, buildings, and mine open pits, and they sometimes result in personal injury or death. Prediction of rockfalls is a difficult task. Slopes that are at risk of rockfall have highly variable geometries. The location, mass, and shape of the rocks that might dislodge and fall are uncertain. Moreover, the materials that make up a slope can vary considerably from one section to another. Furthermore, the relevant material properties are usually not well known. Performing probabilistic simulations of rockfalls, combined with proper statistical analyses, has proven to be an effective and acceptable method for dealing with these difficulties [1, 2, 3]. The movements of a falling rock can be classified as freefall, bouncing, sliding, toppling, or rolling. The falling trajectory is controlled mainly by the geometry of the slope, the block shape, and the energy dissipated at each contact of the block with the slope. A rockfall model is evaluated based on its ability to efficiently predict the velocity, frequency, height of bounce, and run-out distance of falling rocks. With this information, the engineer can design remedial measures such as restraining nets and ditches. Most of the existing rockfall simulators are based on particle models that consider the falling rock as an infinitesimal particle with a mass, called the lumped mass or stereomechanical models [1, 2, 3, 4]. Other models involve hybrid methods relying on simplified assumptions. The most common hybrid methods are based on contact searching for the movement of a dimensionless object and incorporate some aspects of rigid body impact for bouncing [5, 6, 7]. There are also some rigid body models in the literature that employ simplified versions of rigid body models [8, 9]. This study applies a more sophisticated rigid body theory based on rigid body impact mechanics (RBIM), which was developed by Stronge [10, 11, 12]. The new theory captures all modes of rigid body movement. Due to the importance of the rock geometry, single impacts of ellipsoidal and prismatic rocks with rectangular cross sections are investigated. The effect of rock slenderness on rebound velocities and energies is also investigated for ellipsoidal rocks. The correspondence between the model parameters and the data from the rockfall literature data will be discussed.

Jan 1, 2007

By J. Drelich, J. Pletka

Lost foam casting patterns are foamed polystyrene shapes glued together into the shape of the part to be cast and are coated with a refractory material consisting of a mineral mixture and binders. Prior to casting, a significant number of the patterns are damaged and inevitably land-filled. In this study, a process is developed for the recovery of foamed polystyrene from the coating and glue contaminants. The process consists of shredding, impact comminution, size classification and density separation. It is successful in separating up to 97% of the contaminants, while recovering 95% of the polystyrene.

Jan 1, 2001