Search Documents

By N. A. Warner, R. K. Manna

Physical modelling of liquid-phase oxygen mass transfer in a water model of part of a proposed new polymetallic smelter has been achieved. A study of solute mass transfer caused by multiple, subsonic air jets contacting superoxygenated water flowing in a channel model of the smelter converting hearth has been carried out. For a wide range of channel flow rates the rate of mass transfer was found to be independent of water velocity. The water model has been used to compare mass transfer for both open-packed and close-packed multiple-lance arrays with circular nozzles of diameters 2.26, 4.95, 10.95 and 24.40 mm. It was found that with fewer of the larger-diameter nozzles a reduction of up to 58% in liquid-phase mass transfer occurred, especially for the close-packed lance configurations. This restriction of liquid-phase mass transfer would result in reduced metal losses in the analogous smelting situation. The larger nozzles, however, exhibited more jet-jet and jet-channel wall interference effects than their smaller counterparts, resulting in an effective reduction in the momentum fluxes of the impinging jets

Jul 1, 1991

By J. Drzymala, K. L. Wolters, T. Chmielewski, T. D. Wheelock, D. H. Birlingmair

Microflotation tests were conducted with a modified Hallimond tube equipped with a fritted glass disk and magnetic stirrer to determine whether the results would support an equation that predicts a linear relationship between particle size and the reciprocal of particle density in water for a specified flotation recovery in a given time. Data obtained with the tube for either hydrophilic or hydrophobic solids fit the equation satisfactorily. It was also shown that the natural flotability of molybdenite is somewhat less than that of elemental sulphur and that sodium dithionite is a good depressant for sulphurised pyrite. In addition, it was found that the untreated pyrite and galena used in the study were hydrophilic and did not float by particle-bubble attachment.

Jan 4, 1992

By E. H. Baker

Vapour pressures of sulphur have been measured over the temperature range 340-1039°C by means of boiling-point measurements, an internally heated pressure vessel being employed with argon as the pressure medium. The results are expressed satisfactorily by a four-term pressure-temperature relation. At the cited critical temperature of 1040°C the calculated critical pressure is 204 atm. From the pressure-temperature relation and available thermal data for the vapour, the approximate composition of the saturated vapour in terms of the various molecular species has been derived for the critical point

Dec 1, 1971

By John Craw

This paper has formulated the methods, both medical and engineering, for the control of pneumokoniosis in the haematite-mining industry in West Cumberland, but this is only part of a general service to improve the lot of the worker in these mines, to make him a better and happier workman, and to permit him to enjoy his work and leisure in comfort and good health. This organization has now been functioning for more than ten years and the results are indeed heartening, but it is only as a result of constant vigilance from the mining and medical point of view that such a plan can operate efficiently. The human element and its full understanding is by no means the least of the problems.

Jan 1, 1947

By J. E. Rouse, D. L. Buchanan

"During the emplacement of the Bushveld Complex in the Potgietersrus area magma reacted with the original floor rocks— Archaean granite or Malmani dolomite and overlying Penge handed ironstone or sedimentary rocks of the Pretoria Series. The complex sequence of sulphide-rich mafic rocks that formed along the contact is known as the Platreef. Associated with the sul­ phide mineralization are important concentrations of platinum-group metals, copper and nickel. Xenoliths of Malmani dolo­ mite have been incorporated into the Platreef and previous work has suggested that anhydrite is likely to have been present in the dolomite. The sedimentarv-derived sulphur thus introduced into the magma exercised an important control on the forma­ tion of the sulphides.Petrographic studies on the Platreef rocks from the Tweefontein area indicate that the original magma reacted with the banded ironstone to form iron-rich pyroxenites. In the Turfspruit area, to the south, the footwall rocks consist of sediments of the Timeball Hill Series. Original argillaceous rocks have been metamorphosed to cordierite-, corundum- and spinel-bearing hornfelses. Graphite was present in the contact zone in both the Tweefontein and Turfspruit areas. Anhydrite-bearing hornfels rocks are also present on Turfspruit.The Platreef rocks that overlie the corundum- and spinel-bearing hornfelses on Turfspruit are peridotitie, and pyroxenites are present in areas underlain by cordierite-bearing hornfels. The absence of orthopyroxene in the peridotite is probably indicative of low silica activity in the original magma. The pyroxenites have, however, undergone silica contamination from the underlying more siliceous cordierite hornfels.Carbon isotope studies indicate that the graphite in the Tweefontein and Turfspruit samples represents organic material orig­ inally associated with the footwall sediments. Sulphur isotope determinations on the anhydrite-bearing floor rocks indicate that this phase is clearly of sedimentary origin and was probably derived from an evaporitic unit within the carbonate sequence. This provides firm support for a model of ore genesis that involved the introduction of additional sulphur into the Bushveld magma. Isotope studies on sulphides associated with the banded ironstone and graphite indicate that these units were not the source of additional sulphur. Experimental studies predict, however, that a magma contaminated with iron- and carbon-rich material would have a high sulphur-carrying capacity. Where additional sulphur is available the magma would achieve saturation early in its crystallization history and precipitate an immiscible sulphide phase. Experimental work has also shown that sulphide precipi­ tation can be triggered by the introduction of salic material into a magma close to sulphur saturation. This mechanism probably played a role in the control of the sulphide mineralization in the Turfspruit area."

Jan 1, 1984

By Tawsaporn Nuchanong, Ian Nichol

Investigations of the dispersion of gold in soils and stream sediments associated with three gold deposits in Thailand indicate the existence of different geochemical dispersion patterns in the three areas, demonstrating the need for the adoption of a variety of exploration techniques. The three gold deposits which were investigated were the Phu Tham Phra-Phu Thong Daeng copper-gold prospect, the Doi Tung and the Huai Hin Lab gold prospects. Overall the investigations at the three localities demonstrate clearly that the chances of exploration success can be significantly enhanced if composite soil samples are analysed to ensure a more reliable estimation of the gold content in soils and if both the 63 micrometre fraction and the field-panned concentrates of stream sediments are analysed because of the variable grain size of the gold characterising different gold deposits and surface environments.

Jan 4, 1992

By Zhengya Lu, F. Lawson

The surface tensions of lead and lead alloys with very low concentrations of silver, tin and copper were measured by the sessile-drop method. The enrichment of silver and tin in the surface of liquid lead alloys at temperatures close to the freezing-point of lead was confirmed, which may explain the unusual behaviour of small amounts of silver and tin in lead bulllion during the sulphur-drossing step of the refining process. From the limited data available copper also appears to concentrate at the surface of the liquid alloy

Dec 1, 1991

By L. Wade, R. Wang, M. A. Horton

Laboratory methods to find the mechanical properties of rock are inherently biased towards stronger strata, which best survive the sample preparation process. Geophysical techniques are not subject to such bias and may be used to predict mechanical properties rapidly and cheaply. Samples (151) were obtained from a borehole that had been comprehensively geophysically logged. The mechanical properties of the samples were established in the laboratory and correlated with the geophysical responses of the strata from which they came. The results indicate that, for homogeneous strata at least, it is possible to predict the unconfined compressive strength reasonably well from sonic travel time measurements made in the field. Predictions of static Young's modulus may also be made from this data source, but with a lesser degree of confidence. A multivariate regression equation is presented which relates down-hole sonic travel time to unconfined compressive strength, depth and the frequency of fractures in the rock mass. This equation may offer potential for the prediction of the mechanical rock properties of fractured and layered strata.

Jan 4, 1993

By D. D. Lei, H. Sevim

Long-term production planning in open-pit mines requires the determination of cut-off grade, mining and milling production rates, a mining sequence, mine life and ultimate pit limits. Since these variables interact in a circular fashion, a genuine solution to the problem necessitates their simultaneous determination. A methodology with this capability is described. This comprises a group of heuristic algorithms and an unconventional dynamic programming algorithm. The method is demonstrated using data for a gold deposit in the western USA

Jul 1, 1996

By G. Merrington, B. J. Alloway

Tailings from three historical mining areas in the UK were leached in columns under a simulated weathering programme which was chosen to represent periods of 1 and 2 years at 3 different ambient temperatures. The total concentrations of Cd, Cu, Pb and Zn in the primary ore minerals present in the tailings showed only a limited correlation with metal concentrations in the leachate. The leachate from columns of tailings that were maintained at a temperature of 25 (+/-3) degrees C contained, on average, 50% more Pb and 75% more Cu than leachate from tailings that were maintained at a temperature of 10 (+/-3) degrees C. The pH values of leachates from all three types of tailings at 25 (+/-3) degrees C were 0.2 units lower than those from columns maintained at 10 (+/-3) degrees C. The concentration of Cd and Zn in the tailings leachates showed no marked difference at the different temperatures. The composition of the leachate was found to be dependent on the type of gangue mineral, the presence of other sulphide minerals and the formation of secondary iron minerals. A comparison of the concentrations of heavy metals in the leachates produced in the laboratory with those in leachates that were collected in the field over a similar period of time from two of the mine sites showed that concentrations were of a similar order.

Jan 8, 1993

By R. G. Siddall, W. Gale

In the UK the development of the science of strata control has been strengthened by a resurgence of interest in the specialism of roofbolting and its associated techniques. The evolution of the theories and practices of strata bolting in roadway stabilisation is discussed. Practical experiences are considered, principally the use of Australian techniques, the relationship between bond strength and annulus and the effects of stress in the ground. Areas of new technology such as cable bolting, injection anchors and on-board bolters are also discussed. The recent advances in computer technology and rock testing equipment and methods have provided the opportunity to simulate ground behaviour under various conditions. Computer modelling developments and the use of techniques to predict ground behaviour are described.

Jan 4, 1992

By J. K. Brimacombe, F. D. Richardson

Studies have been made of interfacial turbulence occurring in reactions in which indium, zinc and cadmium, dissolved in amalgams, are oxidised into aqueous phases by ferric or mercurous ions. It has been found that this turbulence occurs when the concentrations of oxidising ions in the aqueous phase become sufficiently great. These concentrations are the same as those at which the mass-transfer coefficients in the aqueous phase increase sharply when both phases are stirred by gas bubbles rising through them. The effects of gas flow rate on the mass-transfer coefficients for zinc in mercury have been established, and the oxidation of pure mercury has been investigated. The relevance of the work to processes involving liquid metals is discussed

Dec 1, 1971

The following procedure was used to determine cut-off grades: define the orebody profile; plan the stope layout and quantify the work involved; formulate equipment-performance norms; calculate unit costs; input process recoveries and metal prices; and calculate the cut-off grade. Use of the method is illustrated using data from a copper mining complex in India. Results from the study led to the following conclusions for underground mines in general. Cut-off dependent costs vary significantly with the stoping method employed, orebody thickness, the degree of mechanisation and the working efficiencies of the workforce and equipment. This applies even within the same deposit. Sub-level stoping and its variants can be operated at a lower cut-off grade than cut-and-fill and its variants. Thinner orebodies affect cut-off grades adversely, but with thinner orebodies very little further reduction in cut-off grade can be achieved once a certain minimum width has been exceeded. For the same stoping method and in the same mine the cut-off grade varies with the degree of mechanisation. Labour-intensive methods require higher cut-off grades. An allowance for working efficiency should be made when calculating cut-off grades. Higher process recoveries allow a significant lowering of cut-off grades

Jul 1, 1996

By J. H. E. Jeffes, C. Diaz

The heat balance and chemical equilibria involved in the production of blister copper from a chalcopyrite concentrate in a single operation are examined. It appears that two stages—one oxidising and one reducing—will be required. The analysis indicates that on thermal grounds the process is possible with a dry, high-grade chalcopyrite concentrate, if oxygen enrichment to about 30 per cent is used, but that copper losses in the slag will be serious and will require a secondary recovery operation. More extensive data on the activities of copper oxide in slags are required to elucidate this point more effectively

Dec 1, 1971

By J A. Hacked

This paper explores the potential to exploit controls over the outputs of the primary blasting operation, arising from the performance consistency benefits gained in using modern bulk emulsion explosives technology. The former, allied with the latest powerful blast predictive software and measuring tools, offers the user the opportunity to apply control over both cost and performance, which has not been possible in the past.

Jan 12, 1997

By Tuncel M. Yegulalp, Selamet G. Ergelebi

A description is given of a method of analysing modern mining systems in terms of reliability and their effects on productivity. Non-exponential distributions, such as the Weibull and lognormal distributions, for failure and equipment repair times are also considered. The resulting non-homogeneous Markov process is solved by the method of stages. A longwall mining system is analysed as an example.

Jan 4, 1993

By M. J. Russell, W. E. Stephens, D. B. Mohamad, A. B. MacKenzie

Redox front processes in rocks are important in the context of both radioactive waste disposal and the development of orebodies. Results are presented from a study of the distribution of uranium and thorium and the natural decay series equilibrium about redox fronts in a granite at the Criffel pluton and Craignair quarry, Dalbeattie in southwest Scotland. The results are considered in the context of large scale uranium aqueous transport in the region and compared with those from a previous study of highly developed redox fronts at Pocos de Caldas, Brazil. Results show that the Criffel pluton has experienced a recent and rapid removal of uranium from the uppermost section of the granite whereas thorium has remained relatively immobile. The radium and uranium distributions indicate that diffusion processes probably control the distribution of radionuclides about the front. These processes are similar to those observed at Pocos de Caldas. The trends of concentration and activity ratio about the Dalbeattie redox front are less pronounced than those at Pocos de Caldas owing to the shorter time available for the process and the lower intensity of weathering at Dalbeattie.

Jan 12, 1992

By L Casari

A study of samples from three sectors of the mine, which was worked from Roman times to 1991, revealed different textures, mineral associations and distributions of trace elements in the sulphides. In the last decade before closure, grades of sphalerite concentrate were in the range 51.67-53.30% Zn and 2.21-2.86% Pb and of galena concentrate 69.43-71.62% Pb and 4.70-8.36% Zn, while the estimated by-product germanium content of sphalerite concentrates sold was 300-400 g/t. Passing the different run-of-mine materials through the same concentrator flowsheet produced middlings and tailings during the preconcentration processing. Separate and alternative treatment of run-of-mine products would have yielded improved recoveries of sphalerite and galena and better values of by-product germanium and cadmium

Jun 18, 1905

By R. R. Liebenberg, M. I. Brittan

The kinetics of the copper segregation process has been investigated. The experimental strategy used to isolate the rate-controlling reaction step is described. This step was found to be the chloridisation of the oxide copper minerals in the ore. The link between the rate of chloridisation and the overall rate of segregation is demonstrated experimentally. The influence on the kinetics of the various parameters in a TORCO system is examined and the implications are discussed

Dec 1, 1971

By J. C. Griffiths

There are two kinds of problems concerning the elements of a population : the first is to estimate the proportion of some specific kind of element in the population, e.g. the amount of gold in a block of ground (equals population) or the proportion of mercury in a sample; the second is to estimate the length, breadth, volume, etc., of a specific kind of element, e.g. the grain size of quartz grains in a beach sand or the size, shape and arrangement of lenses of ore in an ore deposit. Given a specific objective, a bounded population, identified elements and the element characteristics of interest, it is then necessary to select a sample of the elements from the population and the problem of sampling requires a decision on how to select the sample. It is also necessary to establish, either by heuristic analysis or empirically, based on long experience, the model frequency distribution of the desired element characteristics: in general, constant-probability models are used as models, the binomial or Poisson for count data and the normal distribution for measurements (or their transformed equivalents). The objective of sampling then becomes to obtain an appropriate statistical estimate of the desired population parameter: for example, the estimators may be the mean (X) and variance (a2): these should be unbiased sufficient estimators of their corresponding parameters (u, a2, respectively). Statistical tests are performed in order to determine that the estimators are of the appropriate kind: all statistical tests are designed to test against bias of a specific kind, although they are stated as tests against randomness. Given a random sample of some population, the estimators are usually stable and adequate to solve the sampling problem. Random samples are simple to define but exceedingly difficult to achieve in practice: in selecting a sample, if every element in the population has an equal chance of occurring, then the sample is a random sample. Interaction between the arrangement of elements in a population, i.e. its structure, and the sample selection process frequently introduces bias—that is, some elements have more chance than others of appearing in the sample and, hence, the sample is not random. An algorithm for dealing pragmatically with this aspect of the sampling problem offers one way of achieving random samples and, therefore, adequate estimators. Examples of the use of this algorithm on various kinds of geological populations, in both field and laboratory, illustrate the requirements for solving sampling problems and the achievement of appropriate estimators.

Dec 1, 1971