Search Documents

By Wolfgang G. Brunner

In the far north of Uttar Pradesh Province in the Indian Himalayas, the 280 MW Dhauliganga hydroelectric power plant is under construction by National Hydroelectric Power Corporation (NHPC), a state- owned enterprise, and a joint venture of Kajima Corporation of Tokyo and Daewoo Corporation of Seoul. This project sets out to develop the lower section of the mountain cascade of the Dhauliganga River, a tributary of the Sarda River, with a 311 m gross head. The 1360 km2 mountainous catchment area is bounded in the north- east by the Chinese border and in the south- east by the Nepalese border. The dam project is located in a remote area north of the principal town of Darchula of the upper Sarda valley, which is one of the seismically most active regions of India. The 56 m high rock fill dam, which will be the first of its kind in India, is faced with concrete and has a 1 m thick, at its crown 270 m long and over 70 m deep cut- off wall of plastic concrete below its toe. The cut- off wall, with a total area of 7500 m2, is constructed by a combination of Bauer hydraulic grabs, assisted by chisels and a Bauer BC 40 cutter which enables the overlapping joint system to be installed, guarantees optimum verticality and enables the cut- off to be keyed into the bedrock formation.

Jan 1, 2004

By David C. Kraft

Atlas Systems, Inc. (ASI) resistance type piers were used to underpin a 100 year old historic structure at Fort Monroe, Virginia. This 3-story structure with basement was underpinned with 155 steel tubular push piers (4" OD) that were hydraulically installed to depths ranging between 90 and 110 ft. and to installing forces in excess of 60,000 lb. Project requirements included lowering the basement floor by 1-1/2 ft. and constructing new footings and adding stem walls to connect to the existing masonry walls. Additionally, the underpinning piers were temporary which required the development of a decoupling system to permit the transfer of the building loads from the underpinning piers to the new footings. The structural loads at the foundation level required a c. to c. pier spacing of 3.75 ft. in order to meet project requirements of a minimum Factor of Safety of 3.0 on the pier load capacity. Project requirements included a load test on the selected underpinning pier (ASI - AP2 4000.219) in order to establish installation depths for seating the piers to 60,000 lb. The project was successful in supporting the full load of the structure during the construction phase. Considerable savings in time and cost were achieved as well as avoiding any vibrations or noise during installation of the piers.

Jan 1, 2002

By Sam Messina

[Project: Job Number: Date: Superintendent: Person Making Inspection: Note: The following checklist shall be used on a regular basis as an overall assessment of the jobsite. The checklist is not all-inclusive. All applicable Federal, State, and local regulations, standards, and ordinances pertinent to the jobsite conditions must be evaluated on a continuous basis. Column A - Adequate Column I ? Inadequate]

Jan 1, 1998

By A. Partos

It was decided to build a fourteen-storied office building over a six-storied garage and a four-storied office building. The high vertical and horizontal loads required foundations on rock approximately 18m below street level. Drilled piers (caissons) were selected. Eight caissons (1.98m diameter) were installed through the six-storied garage and four caissons from a temporary deck at the location of a former two-storied building. Excavations were done by the slurry method. Proof testing of rock was done before construction by test borings and during construction with a core barrel of small diameter. Quality control measures included telecommunications between ground crews and the equipment operator on the garage roof; records of field observations and testing of bentonite slurry and rock; and a continuous evaluation of all information. Instruments were installed in one caisson to monitor load distributions and curing of concrete.

Jan 1, 2010

By J. H. Qian

China is one of the countries with comparatively wide distribution of soft soil. In the wake of the rapid developement in the national economy and construction, the improvement technique of soft soil foundation has been perfected gradually. At the present, an integrated system of soft soil improvement has formed, features of such a system are shown by the variety of improvement methods, the complement of theoretical study to project practice. This paper summarizes mainly the following methods: lime column, vertical drain, vibroflotation and dynamic consolidation.

Jan 1, 2010

By J. G. La Fonta

The rapid development of real-time monitoring technology for the construction of large underground structures in urban areas can be attributed to: the zero-risk objective, the need for transparency between all parties involved and the control of real cost within the budget. Real-time monitoring can be an integral part of the construction contract (for example when compensation grouting is required) or independent, in particular when measurements of existing structures and buildings bordering the project are to be taken before construction starts. Three examples of extensive field instrumentation schemes are described: a large road tunnel in the Moscow suburbs, a new metro line in Amsterdam and major redevelopment works at a busy Central London rail interchange.

Jan 1, 2006

By Djk Arentsen

A new technique to drive tubular piles by impact hammer inside the pile has confirmed a dramatic reduction of noise and the opportunity to save steel. Also a reduction in driving time and a higher bearing capacity has been observed during a test program of this technique. As part of the so-called "Down-the-hole" driving technique, a wave equation analysis has been developed to calculate driveability and pile stress. The main feature of the new "Down-the-hole" technique is the development of a patented device allowing uncoupled penetration of pile tip and pile shaft, which makes it possible to drive both closed or open end piles and reduce the stress level induced in the pile wall. During a test program, a number of instrumented piles were driven and compared with traditional driving of the same pile with the same hammer on top (also instrumented). Also the stresses and performances were compared with precalculations. This paper, explains the technique and presents the test and noise results, in comparison with traditional top-pile-driving. The "Down-the-hole" driving technique is an interesting alternative for special applications where traditional pile driving requires a large wall thickness or in areas where noise is a hot item.

Jan 1, 1996

By K. Viking

It's well known that conventional impact hammers, usually are the method to use in order to drive precast prestressed concrete piles. However sometimes the vibratory technique might be considered as a suitable alternative due to favourable soil conditions. It is also well known that piles driven into granular soils can be installed more efficiently by the use of a vibratory driver compared with impact hammers. However, the use of the vibratory technique is seldom regarded as the first choice, since the technique is constrained by several uncertainties related to the pile capacity, and concrete piles to cope with tensile stresses. With the opportunities of having suitable subsurface conditions and a fair amount of piles to be installed, it was anticipated that the use of the vibratory method could result in a significant reduction of the installation costs. Part of the uncertainties of using a vibrator was intended to be eliminated by restriking the vibratory driven pile with an impact hammer and use a Pile Driving Analyzer? (PDA) to correlate recordings of soil resistance to driving with measured rate of penetration, and to evaluate the static capacity and load/settlement characteristics of the vibratory driven pile by conducting static load test. The conducted test study of using a vibrator to drive the precast prestressed test pile (14-in. square by 30-ft-long) did not turn out to the author's complete satisfaction. The present paper focuses mainly on a numerous practical engineering issues in relation to the use of the vibro-technique to drive precast prestressed concrete piles in granular soils. The obtained experiences of using a PDA to monitor vibro-driven piles, with its potential and limitations, is presented and discussed. Furthermore, a simple method of how to subjectively pre-estimate the soil resistance due to vibratory driving is presented and discussed. The reasons for the partly unsuccessful test study are discussed in great detail based on the obtained experiences. Suggestions of how to better approach a similar situation in the future are also provided in great detail

Jan 1, 2004

By Ali Porbaha

In today's fast-track construction environment, owners are searching for non-conventional technologies to build their projects faster and safer while maintaining traffic flow during construction. To that end designers and contractors are providing solutions that incorporate many unique features to expedite construction processes. In addition to timely delivery of the finished highway products, there is an increasing interest in making the initial investment in applying innovative technologies and thereby minimizing costly maintenance of highway projects. Accordingly, the aim of this paper (along with the accompanying paper) is to examine innovative technologies, developed mostly in Europe, that accelerate construction of highway, runway and railway embankment foundations. For each technology, a basic concept, installation technique(s), and design considerations are discussed, along with the case history of a real-world project. The Geotextile Encased Columns (GEC), AuGeo, and Continuous Flight Auger (CFA) are presented in Part I. Deep Mixing (DM), Cut-Mix-Injection (FMI), Mass stabilization, and Combined soil Stabilization with Vertical columns (CSV) technologies are discussed in Part II.

Jan 1, 2002

By Darrell Wilder

The Trenton Water Treatment Facility in Trenton, New Jersey, is expanding to upgrade existing facilities and to meet the increasing demands of the public. The facility sits uncomfortably between the northern bank of the Delaware River and Route 29, a busy traffic corridor. Flooding along this bank of the river occurs frequently and disrupts traffic along Route 29. The expansion plans for the facility call for several large clarifying tanks on a mat foundation covering an area of about 100 x 350 ft. The original design was to remove and replace up to 20 ft of existing fill and soft materials. Due to the close proximity to the existing structures and the Delaware River, it would be necessary to use sheet piles and tiebacks to support the proposed excavation, as well as the existing structures. The solution adopted consisted of the installation of vibro-replacement stone columns to improve the in situ soils and eliminate the need for excavation and replacement. This approach was tremendously successful. It mitigated the significant risk of flooding of the excavation, and provided a cost-effective alternative to mitigate settlement of the proposed tanks on the poor soft subgrade soils. This paper presents the details of the criteria for selection and design of the stone columns, and the process followed for installation of the stone columns and for verification of the level of soil improvement achieved. It also includes a back analysis of the results of a large scale, 10- by 10-foot plate load test performed on a group of stone columns using numerical procedures and recommendations for design and construction.

Jan 1, 2008

By Ben C. Gerwick

Large diameter steel tubular piles installed vertically or on a slight rake, offer many advantages as the foundations of major overwater bridge in regions of high seismicity. By proper selection of diameter and wall thickness, an optimum balance between stiffness and strength can be achieved. Under strong seismic motion, the piles will deflect and bend so as to reduce the acceleration forces transmitted to the superstructure, while still limiting drift. A major advantage of this concept is that the mass of the footing block is significantly reduced from that of the conventional pier. The design of the footing block requires great care in order to transfer the high shears and moments. Where the soils consist of significant depths of sediments, the kinematic interaction of soils, piles and structures must be considered. Moments will be a maximum just under the footing block. Filling the top portion of the pile with concrete will prevent local buckling and assure ductile behavior even under overload. Typically the piles will be long, with most or all of their support furnished by friction and will require the use of very large pile hammers to achieve the required capacities. Where the piles are founded on rock or in hardpan, sockets will be drilled and filled with reinforced concrete. For these piles, high moments can occur both at the head and just below the rock surface, so the concrete infill should extend the full length. This paper describes the use of tubular piles driven through the deep silty sands of the Jamuna River, Bangladesh, and also where socketed into the near-surface rock for the mail pylon pier of the new San Francisco-Oakland East Bay Bridge in California.

Jan 1, 2013

By Michael J. Garlich

Steel sheet piling has a long history of use in a variety of permanent and temporary structures. Current engineering practice uses numerous publications and standards for design guidance. U.S. design guidance is fragmented, with numerous inconsistencies between design guides. To improve current U.S. design practice, the North American Steel Sheet Piling Association has initiated a project to produce a design standard that will unify design procedures and provide specification guidance for engineers and users of steel sheet piling. The wide range of uses for sheet pile structures presents a challenge in developing such a standard. Load factors or allowable stresses acceptable for a temporary retaining wall in soil may reasonably vary from those for a river cofferdam or a dockwall located in sea water. However, it is still possible to provide consistent and rational guidance for such varying uses. The standard also can address sheet pile design aspects often neglected in U.S. publications, such as vertical load capacity and resistance to loads applied parallel to the sheeting.

Jan 1, 2008

By Brent Wilkins

The project team was tasked with the design and installation of a deep foundation system to support an expansion to a power generating station in Glenrock WY. Cast-in-place piles installed by a fixed mast drilling platform were assessed to be the most efficient foundation system for the subgrade conditions and range of design loads for the project. It was determined that conventional augered, cast-in-place piles could not be installed to the required pile toe elevations. Subsurface materials consisted of interbedded coarse- and fine-grained soils to about 23 ft to 30 ft depth below the ground surface, underlain by carbonaceous shale (claystone) with interbedded sandstone. The overburden materials varied from very soft to medium stiff and loose to dense. The claystone was typically foliated and very weak to weak whereas the sandstone was typically massive and very weak to weak. The site characterization consisted of a variety of field and laboratory programs including soil borings with Standard Penetration Tests, pressure-meter testing, and geophysical testing. A load test program was performed involving the compressive, lateral, and tensile testing of piles ranging from 14-in to 24-in diameter. Compression test piles were instrumented with vibrating wire strain gages. The paper includes a discussion of the regional and local geologic and geotechnical parameters, particularly the results of the various in situ and laboratory test programs. The selected foundation system is introduced. Load test results are then presented along with analysis and discussion of these results with regard to performance of the piles in the claystone.

Jan 1, 2009

By Edwin W. Hickey

This paper briefly discusses the geologic conditions in South Florida relative to the design, construction, and performance of deep foundations. The subsurface conditions in this area are unique in that the rock layers are highly porous and often very soft, and are sandwiched between layers of typically loose, uncemented quartz fine sands. Due to the high porosity of the Miami Limestone, 4-inch diameter rock coring is often required to obtain intact samples, and dewatering of excavations is sometimes difficult or impossible. The sand layers, typically tens of feet thick, are very loose to loose in relative density and have been the cause of unexpected large, deep foundation settlements. The engineering properties of the various geologic formations are discussed, along with typical deep foundation types used in the Miami area prior to and after 1980.

Jan 1, 2003

By Garland Likins

The Texas Department of Transportation, now considering using Augered Cast-In-Place (ACIP) Piles (also known as Continuous-Flight-Auger or CFA Piles) in their foundations, awarded a research project to Professor Mike O'Neill at the University of Houston (UH) to study the advantages and potential difficulties with ACIP/CFA piles. ACIP/CFA piles were installed on three sites for UH; they had extra instrumentation and additional measurements by UH staff during installation which are beyond the scope of this paper. Independent visual logging of the pile was done by an experienced inspection firm. The main advantages of ACIP/CFA piles are their speed of installation and their economy. Potential savings are substantial. Disadvantages include an unknown structural condition of the shaft. Inspection is critical, but many simultaneous observations make accurate inspection difficult. Because of resulting uncertainty, many engineers have avoided ACIP/CFA piles in the past.

Jan 1, 1998

By Scott M. Doehla

A proposed rehabilitation of a 200,000 sf, 75-foot high steel-frame building at the former U.S. Navy Yard in Brooklyn, New York required the review of existing foundation data and an investigation of the foundations with respect to their condition. The building was constructed in stages between 1856 and 1933, including several expansions and interior equipment with isolated foundations. The building has clear spans on the order of 50 feet and at one time supported cranes allowing transport of heavy equipment through the building. The proposed rehabilitation is to include a food manufacturing center and office space having multiple stories. Original construction drawings, available from the Brooklyn Navy Yard Development Corporation?s drawing archive, were reviewed to determine the foundation system supporting the structure. The original drawings provide a window into the methods utilized during late 19th and early 20th century pile foundation construction. The review revealed that the building is supported by pile foundations ranging from timber to concrete-filled steel pipe (depending on the year of construction). Annotations including pile driving records were available on some drawings indicating the design and as-built capacity (using the ENR formula for driving resistance). An investigation consisting of test borings was performed to identify the subsurface conditions underlying the building for evaluating theoretical capacity of the piles. A test pit investigation was performed against existing columns within the structure to expose the piles and pile caps for inspection pertaining to pile condition. The test pit investigation revealed methods utilized during original construction to integrate new columns with existing floor slabs, the use of below-grade brick arches to support a floor slab, and the condition of timber piles which were likely installed up to 120 years ago. The observations made within the test pits were compared with original drawings to evaluate the accuracy of these drawings.

Jan 1, 2008

By Cem Altuntas

This paper is the second in a series of two describing the design and construction of a foundation for a major high-rise real estate development on the west side of Manhattan, N.Y. The foundation members consist of large-diameter rock-socketed caissons, driven closed-end steel pipe piles bearing on rock, and a secant-pile retaining wall surrounding the entire site. This paper focuses on the Osterberg cell (O-Cell) load test completed for determining the allowable side-shear resistance between the concrete and the sides of the rock socket. Different qualities of mica schist bedrock, demonstrated by the penetration of rock with the soil auger or drill casing, were encountered. Accordingly, an additional subsurface investigation consisting of test borings at each caisson location was completed. Unconfined compressive strength tests were performed on representative rock samples. The ?soft? mica schist was observed to have vertical foliations and high mica content. For the first time in Manhattan, an O-Cell load test was performed to determine the allowable side shear resistance for both the soft and hard mica schist bedrock. The side shear resistance obtained from the O-Cell load test is compared with the side shear resistance allowed by the New York City Building Code and empirical correlations using unconfined compressive strength values for rock. The rock socket design for the caissons was refined based on the O-Cell load test results.

Jan 1, 2008

By Eric Brandner

Expansive soil formations can be found throughout the United States. When subjected to wetting, many of these formations have the potential to swell and exert large uplift forces which can significantly damage lightly-loaded structures. Designing an economical foundation that can resist uplift forces is critical to prevent damage to these structures. The current solutions to control uplift due to swelling soils, such as over-excavation and replacement of the expansive material, or drilled shafts, can be costly and problematic. Piles made from recycled polymer materials may provide a solution. Due to a lower coefficient of friction along the interface than piles made from traditional materials, solid recycled plastic piles can allow expansive soils to move nearly independently from the pile when wetted. This results in a much smaller magnitude of uplift force being transferred to the structure which minimizes the risk of significant structural damage. This paper presents the preliminary results of research conducted on the use of recycled plastic piles in an expansive shale environment. The preliminary phase of the project involved the installation of six 13 in. (330 mm) diameter recycled plastic piles at a test site on the South Dakota School of Mines and Technology campus. The piles varied in length from 15 ft. to 25 ft. (4.6m to 7.6 m). Two of the piles were subjected to a full-scale compression load test in order to determine ultimate capacity, while the additional four piles are being subjected to long-term monitoring of uplift movement. A cast-in-place concrete pile, with a diameter of 6 in. (152 mm) and length of 15 ft. (4.6 m), was also installed at the test site for monitoring. The preliminary results indicate that the use of solid recycled plastic piles is a viable alternative for support of lightly-loaded structures in expansive soil environments.

Jan 1, 2009

By Ambarish Ghosh, Subhaprasad Chakraborty

"Construction of basement floors has become necessary to meet the requirement of parking in office and residential complexes and in hospitals for radiotherapy treatment. Important projects coming up in Kolkata are mostly in closer proximity of residential buildings, office buildings and historical monuments. Sheet piling is mostly used as temporary shoring system during construction. Deep excavation in urban environment creates great problem related to construction induced vibration due to driving of sheet piles for basement, pile driving etc. which raises the chances of damage of adjacent buildings and nearby structures. Vibratory sheet-pile driving is the most common method of sheet pile installation. The knowledge of induced vibration due to this phenomenon is still very deficient. This paper presents the analysis of measured vibration data collected from different sites of Kolkata with varying soil profile. Typical two case studies of sheet pile and pile driving has been presented and the vibration values are analysed. The responses of the vibration are reported in terms of peak particle velocities (PPV). To evaluate the effects of vibration due to pile driving two aspects have been considered: the effect of the energy entering the ground from the pile and the effect of the soil condition.INTRODUCTIONIn urban areas infrastructure development projects are mainly located adjacent to existing structures like residential buildings, offices and historical structures. The construction work of such project influences the surrounding environment as well as human perception (Wiss 1981). During the construction of basement for residential complexes and hospitals sheet piling is mostly used as temporary shoring system or as to support the earth mass. The vibration induced due to driving of piles and sheet piles have been presented herein. Deep excavation projects close to existing structures increase the concern of environmental impact. For this reason the vibration assessment and prediction has become a subject of great interest. It is important to develop a site specific model for predicting the ground vibration resulting from pile and sheet pile driving at the construction sites. The developed model gives the efficacy to guide the engineer to select the construction methodology ensuring the safety of the surrounding structure. The model developed here is site specific and the parameters that has been used are dependent on the soil condition and the energy source."

Jan 1, 2015

By Chandramohan P. V., Ravi Kishore

"An underground reservoir was to be constructed at Doha in Qatar. Simsima lime stone is present at the bottom. When the reservoir is empty, there will be uplift at the bottom but this will change to downward load when it is full. The rock at the bottom had high bearing capacity to resist downward load. But uplift had to be resisted by piles or anchors. The reservoir has a size of 120mx80m. Shrinkage and creep of concrete coupled with thermal contraction imposed a horizontal movement of 26mm on the extreme piles. So, piles have to accommodate this as well. This unique situation needed a unique solution. The solution was to provide piles with flexible high tensile strands to take tension. An annular space near the head of the pile would facilitate horizontal movement as well. Compression load was directly passed on to the raft bearing on rock.INTRODUCTIONAn underground reservoir for storage of drinking water was to be constructed at Doha, Qatar. The reservoir was proposed to have a plan size of 120m x 80m. Clear height inside the reservoir was proposed as 17.2m, from the bottom of roof to the top of bottom raft. Overall height of the reservoir at the outlet from the top of the roof to the bottom of raft was to be 21.2m. For the sake of inspection and in order to prevent pollution from the surroundings a gallery was planned around the reservoir. This could accommodate pipelines as well. This gallery was 3.0m wide on three sides and 8.4m wide on the outlet side.The gallery had removable gratings as cover in order to facilitate maintenance. Capacity of the reservoirwas proposed to be 40million gallons. The reservoir is divided into four compartments with baffle walls in each one for water circulation. Roof of the reservoir is kept at 300mm above ground level. There are two levels of car park on top of the reservoir. Top of the reservoir roof is at +14.35. Bottom varies from - 6.68 to -7.08. Lowest water table is at +6.00. Concrete structure of the reservoir was designed by a local consultant. The Navayuga Engineering Company was entrusted with the construction. Please see Figs 1 and 2."

Jan 1, 2017