Search Documents

By Min Sunn Ye, Wei Wang, Huawen Xiao, Kai Yao, Fook Hou Lee, Siang Huat Goh

"Previous research have shown that introducing fibers to cement soil mixture is effective in improving the ductility as well as maintaining the strength of cement-treated soil. A good knowledge of stiffness of the improved soil at small strain is essential for realistic predictions of ground movements that may affect adjacent buildings or underlying infrastructure. This paper presents a triaxial system with local strain measurement developed for studying shear modulus degradation of cement treated clay with fibers. Cylinder specimens (70mm diameter by 140mm height) with 50% cement, 100% water, 0% to 1% polypropylene fibers by mass, and 7 days of curing period were used. A local strain measurement system with floating type miniature submersible LVDT is introduced in this paper. Configuration of the mounts including the pin size, length and distance are presented and discussed. Based on the experimental results, a reasonable configuration of the mounts is recommended for fiber reinforced cement treated clay. Results showed that the proposed local strain measurement system is effective for testing the shear modulus degradation of cement treated clay with fibers under both unconfined and confined condition. Comparisons with results from resonant column and bender element tests served to verify the reliability of the local strain measurements using the proposed method.INTRODUCTIONIn many geotechnical engineering problems, the operational strain domain ranges from 10-3% to 10- 1%. A good knowledge of stiffness at small strains is essential for realistic predictions of the ground movements that may affect adjacent buildings or underlying infrastructure. As such, during the last 3 to 4 decades, the importance of using the small strain stiffness of soils for the design of foundation and underground structures has widely been accepted. Triaxial testing has been widely used to study the stress-strain behavior of soil in the laboratory. However, the stiffness obtained from the conventional triaxial apparatus is usually far smaller than those back-calculated from field measurements. This is mainly attributed to the overestimation of axial strains from the external strain measurements, which usually includes compliance effects of the loading and load measuring system as well as sitting, bedding and alignment errors between sample and system (Baldi et al., 1988). The poor resolution of the external strain measurements is another important contribution. Therefore, conventional procedures are inappropriate for small-strain stiffness evaluation due to low accuracy and resolution."

Jan 1, 1900

By Shawna Munn, Carol Dounitch, Erika Acton

The EQ Bank Tower, a 24-storey office tower with 4 levels of underground parking, is currently under construction at 25 Ontario Street in the downtown core of Toronto, Canada. The tower geometry required an 18 m (60 ft) deep excavation inside an existing 3-storey 100-year-old façade, to be retained in place throughout construction. This presented a variety of design challenges that required several innovations and a customized monitoring program. In this paper, we will discuss two major challenges, and highlight the innovative and adaptable solutions carried out using performance-based design leveraging the observational method. The first was installation of a shoring system in a 500 mm (20 in) gap between the historical façade and a live gas main. The second involved excavating 10 m (33 ft) into expansive shale bedrock adjacent to a sensitive neighbouring building.

Oct 1, 2022

By Inc. Pile Dynamics, Daniel S. Belardo, Marcus Galvan, George Piscsalko

Soil nails are often utilized as a temporary or permanent earth retention technique for slope stabilization and for excavation retention for existing or new structures. Soils nails are generally advantageous as installation is relatively rapid and they can be installed beneath existing structures and where site access for equipment is limited. Due to the typically small cross-section of these elements, the inability to inspect the holes prior to grouting/concreting, and the various installation techniques utilized, quality control for assessing the integrity along the entire length is limited. Currently, quality assurance is conducted by load testing to verify the pull out capacity after installation. The load testing is typically done on a small percentage of the total number of soil nails. This paper will provide the results of a demonstration where the new Non-Destructive Test (NDT) method Thermal Integrity Profiling (TIP) was used to access the integrity of several soil nails along their entire lengths. This TIP method has been successfully used for several years to assess the integrity in drilled shafts and ACIP piles. The TIP method assesses the integrity across the entire cross-section and can identify regions where bulges, necks, and insufficient grout/concrete are present. TIP testing can also help assure that the contractor's installation methods are adequate and consistent for the intended design. For the project presented, instrumented Thermal Wire were affixed to the centered tension bars prior to placement in the excavated shafts. Temperature measurements were recorded from the hydration energy generated after grout/concrete placement, capturing the entire heating cycle. Manufactured defects were installed on the center bar at multiple locations. The results and conclusion will be discussed as well as recommendations for future use.

Jan 1, 2017

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By Tomohide Takeyama, Binh T. T. Nguyen, Masaki Kitazume

"Deep mixing columns are widely used to support embankments constructed on soft ground area. Researches on the stability of deep mixing columns were done by some authors when the columns do not simultaneously fail but individually fail at different time. A layer of shallow mixing is proposed to reinforce these columns as a group to increase the stability as well as loading capacity of columned improved area. Two centrifuge model tests were done to observe the effect of shallow layer on reducing embankment displacement as well as on failure pressure of improved ground. Acrylic piles were used as deep mixing columns in the centrifuge tests to avoid unexpected internal failure of columns. The results of centrifuge tests were also simulated by 2D FEM to back-analyze the centrifuge experiments. A good agreement between the centrifuge experiments and the numerical simulations shows that by using a shallow layer reinforcing individual columns, the horizontal displacement at the embankment toe reduces by 60 % and the tilting failure is clearly indicated in columns without shallow layer. Although, no significant failure was observed under the current centrifuge condition, the failure pressure of improved ground was significantly increased with the columns reinforced by shallow layer.INTRODUCTIONCement or lime and soil mixing technique was firstly used in Japan and Nordic countries since 1970s. The technique is used to improve soft soil by increasing its mechanical properties including strength and consolidation characteristics (Kitazume and Terashi 2013). Various researches were done to investigate the characteristics of mixing material due to various factors including types of binder, condition of soil, mixing condition and curing condition (Terashi 1997). On the other hand, many studies focused on the application of in-situ mixing technique such as supporting embankment and underground structure as well as working as the foundation of building and factory (Kitazume and Terashi 2013). In term of embankment supporting, column-type improvement is taken into account for huge applications. Due to loading from embankment, the deep mixing columns tend to fail either external failure (Kitazume and Maruyama 2006) or internal failure (Kitazume and Maruyama 2007). However, the deep mixing columns do not fail simultaneously but instead one by one at different time (Kitazume and Maruyama 2007). Because the deep mixing columns work and fail individually, the strength and stiffness of all columns cannot be mobilized simultaneously. By using a shallow mixing layer fixing the top of deep mixing columns, individual columns may work simultaneously. A combined technology of shallow stabilization and floating-type cement treated columns is used to reduce settlement of a high embankment on soft ground (Ishikura et al. 2007). A research on effect of surface improvement layer on internal stability of group column type deep mixing improved ground under embankment load was reported in the Port and Airport Research Institute, Japan (Kitazume 2011). However, the failure pattern of shallow and deep mixing combined structure has not well studied. This research focuses on the external failure mechanism of the combined structure by centrifuge model tests and back-analyzed simulation using 2D finite element method. The effect of shallow layer on embankment displacement and the yield point of the improved ground is also discussed in this study."

Jan 1, 2015

By Abu B. Siddique, Anthony S. Crincoli

"The New Jersey Turnpike Section 2 widening program consisted of widening between Interchange 6 in Mansfield Township, Burlington County and Interchange 9 in East Brunswick Township, Middlesex County. To accommodate large volume of traffic the roadway was widened from 6 to 12 lanes with major modifications performed at four interchanges. The Section 2, NJTA Interchange 6 to 9 Widening Program is a 4.2-mile section of Turnpike roadway which included a total of 12 new or modified structures. In order to facilitate the construction process Section 2 was divided into three construction contract packages. This paper will cover the last and final Contract T869.120.203 which is 1.7 miles in length. The work generally consisted of eight new ramps connection to and from the toll plaza to the new inner and outer roadways. New mainline bridges were constructed over several ramps. A new bridge was constructed to take northbound outer lanes traffic over two ramps along with new mainline bridges over Black’s Creek, Georgetown Road, and Laurel Run. In addition, a new bridge was constructed to take a ramp over Laurel Run and the existing U-turn Bridge was replaced with a new one.For Contract T869.120.203 a total of 74 five-foot diameter drilled shafts has been constructed to support all pier foundations for bridges. Three drilled shafts were tested using Osterberg Load Cells to verify the estimated shaft resistance during design phase. One Osterberg Load Cell test was performed on a demonstration (sacrificial) shaft and the other two Osterberg Load Cell tests were performed on production shafts. This paper compares the estimated total, side and tip resistances with corresponding measured total, side and tip resistances and provided recommendations for future design purpose.INTRODUCTIONTo accommodate large volume of traffic the New Jersey Turnpike Authority (NJTA) decided to widen Section 2, which included Interchange 6 through Interchange 9. The Section 2, a 4.2-mile section of Turnpike roadway that was widened from 6 to 12 lanes with major modifications performed at four interchanges.The New Jersey Turnpike Authority (NJTA) procured AECOM to perform engineering services for the final design of Section 2, NJTA Interchange 6 to 9 Widening Program. Section 2 is a 4.2-mile section of Turnpike roadway that will widen from 6 to 12 lanes and will include a total of 12 new or modified structures. It encompasses modifications of the existing and the design of four new ramps at Interchange 7. The project also includes the modification of two local roads over the mainline, two local roads under the mainline, two maintenance U-turns, and retaining walls. In addition, the project consists of the design of noise walls, sign structures, storm water management basins and the more typical drainage, utilities, lighting, roadway, ROW, and signing and striping design."

Jan 1, 2015

By Keithe J. Merl, Brendan FitzPatrick, Gregg Piazza

Urban and industrial construction projects commonly involve interior work within buildings, warehouses and manufacturing facilities. Renovations of these existing structures must address both structural and geotechnical engineering challenges while also balancing the practicality of implementing solutions within site constraints including limited site access, overhead clearance restrictions, vibration tolerances and uninterrupted facility operations. This paper highlights two projects for an international shipping company where mezzanine level additions within active shipping facilities required construction of new foundations. Construction requirements included low vibration levels, as well as rapid and clean installation to limit impacts on the active shipping operations. The selected system also needed to adjust to both variable ground conditions and differing overhead clearances. This paper describes the installation, design and performance of Ductile Iron Piles used to meet the project challenges. The low vibration, driven pile system offered the ability to work within restricted overhead environments while successfully delivering working compression capacities ranging from 45 to 75 tons (41 to 68 tonnes) as well as lateral and tension resistance. The paper also presents the results of site-specific load testing (and pile capacity) for various termination criteria. INTRODUCTION Urban and industrial construction projects commonly involve interior work within buildings, warehouses and manufacturing facilities. Renovations of these existing structures must address both structural and geotechnical engineering challenges associated with the new construction. Foundation solutions must also balance the need to achieve design requirements with the practicality to be installed within the particular site constraints including limited site access, overhead clearance restrictions, vibration tolerances and uninterrupted facility operations.

Jan 1, 2019

By Juan M. Pestana-Nascimento, Robert G. Bea, Hamed Hamedifar, Emery M. Roe

The current State-of-the-Practice is grounded heavily on deterministic characterization and assessment of the performance of civil engineering infrastructure. In particular, flood defense systems, such as levees, have been evaluated within the context of the Factor-of-Safety where the computed capacity of the system is compared with the code specified demand forces. Uncertainties associated with the capacity and demand forces render deterministic modeling incomplete. In particular, two structures with the same Factor of Safety can have vastly different probabilities of failure. While efforts have been made to assess levee vulnerability, results from traditional engineering approaches omit important factors because they do not account for uncertainties included in analytical modeling, and natural variabilities, or human and organization factors. This paper utilizes risk assessment methods to advance methods for quantifying the contribution of uncertainties to engineering analyses, and thereby provide additional information to help assess sustainability of geotechnically engineered systems. The probability of failure of a geotechnically engineered system is directly impacted by how well the system is understood, and how uncertainties are incorporated in development of understanding of the system. This paper presents methods to evaluate two types of uncertainties for three potential failure modes of flood protection levees: underseepage, slope (or levee) instability, and overtopping/erosion. These analyses account for two types of uncertainty: 1) Type I – inherent uncertainty, 2) Type II – analytical modeling uncertainty. Human and organizational task performance and information development and utilization uncertainties are not included in these analyses. This paper focuses on the behavior of the flood protection levee system for Sherman Island, a western island in California’s Delta. Sherman Island is of critical importance to California because of the very important infrastructure systems that pass under, on, over, and adjacent to Sherman Island, including: natural gas pipelines, regional and interregional electricity transmission lines and telecommunication facilities, two deepwater shipping channels; and State Highway 160, a link between major transportation expressways. The work evaluates current (year 2010) and future conditions (year 2100) and incorporates variations in capacity and demand arising from projected human response activities and global climate change.

Jan 1, 2017

"Integrity tests refer to a variety of non-destructive tests (NDT) whose purpose is to measure or determine the quality and uniformity, and some- times dimensions, of cast-in-place concrete foundation elements. The tests are primarily aimed at detecting zones of poor quality concrete, voids, bulges, and/or necking.The non destructive integrity testing techniques in this section most generally used for drilled shaft testing are based on one of two physical principles - stress wave propagation or nuclear radiation. All of the stress wave methods involve monitoring a deliberately created vibration, usually of very low amplitude (strains on the order of ??). Some methods rely on direct transmission of the signal, while others rely on processing reflections of the imposed signal.The stress wave methods are inherently sensitive to vibrations from other sources, especially at frequencies that fall within the range of interest for the particular test being applied. Construction activity near the shaft being tested; such as: demolition jack-hammering, pile-driving, casing vibration, excavation and movement of track-vehicles are all known sources of interference that might render test data useless. The actual effect of such vibrations will vary with the type of activity, soil conditions and distance from the testing. The test operator must be able to recognize such interference, and the contractor should be prepared to cooperate with the testing personnel by stopping or moving the source of vibration. If this cannot be done immediately, testing should be postponed until the work in question is finished and the vibration source moved or shut down.NDT methods are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT methods do allow measurements of the quality of concrete placed in drilled shafts, which cannot be made from "topside" construction inspection. They should be considered supplemental to routine construction inspection as they do provide an additional level of quality control."

Jan 1, 2004

By Gary L. Seider, Dana A. Wesolek, Fred C. Schmednecht

"A new condominium project, The Atelier, developed by Pickus Companies located at the corner of Bryn Mawr and Sheridan in Chicago, IL required an earth retention system to protect the surrounding roads, alley, and existing neighboring apartment bui lding during its construction. Slurry Systems, Inc. (SSI) and Ground Engineering Consultants, Inc. designed the earth retention system using cantilevered sheet piling for three of the four sides: two sides bordering major streets and one side bordering an alley. For the fourth side, which borders an existing occupied brick building, a combination of sheet pil ing and AB. CHANCE® helical screw piers were used. SSI was actively involved in the review process of its earth retention system with the City of Chicago and quickly learned that there was no specific code for hel ical piers/anchors. (It appears that this is the case with most metropolitan cities throughout the United States). Consequently, the approval of underpinning for this project became the critical path, as much testing, calculations, meetings, and other details were required prior to its approval.SSI and AB. CHANCE® recognized that this process for underpinning approval must be seen by other contractors/suppliers who wish to use helical piers/anchors in the City of Chicago. Consequently, this project served as an opportunity to work with the City of Chicago and the City's Building Code Committee in furthering the development of the Helical Piers/Anchors Code, Section 1814. INTRODUCTION - HELICAL PIERSDefinition. A helical pier or anchor consists of one or more helix-shaped steel bearing plate(s) attached to a central steel stem (solid bar or pipe), which is installed by rotating or ""torquing"" into the ground. Each helix is attached near the tip, is circular in plan , and is formed into a screw thread with a defined pitch. Helical piers/anchors are pre-fabricated and can derive their load-carrying capacity through both end bearing and skin friction. The helical piers/anchors can be augmented with grout."

Jan 1, 2005

By Steffen Schweizer, Tadeusz Brzozowski, Alfred Koller, Michał Topolnicki, Jürgen Wäger, Grzegorz Sołtys

A full scale test has been conducted to determine ground bearing pressure under rig tracks. The track loads were recorded in real time using Liebherr's Ground Pressure Visualisation system, and the vertical stress induced in the ground was measured with pressure cells embedded in the ground. It has been found that the recommendation of EN 16228 regarding determination of the track length is oversimplified. The contact length should dependent on the susceptibility of the working platform. It has been also demonstrated that the corrected pressure distributions under the tracks influence the dimensioning of the working platforms. As a result, the designed working platform may actually be less secure than is shown by conventional calculations.

May 1, 2022

By Arash Khosravifar, Ali N. Ibrahim

"Large areas of Iraq are covered with collapsible soils namely gypsiferous soil which is often used as the foundation soil for structures. In particular, the Mosul Dam foundation is comprised of high contents of gypsiferous soils. Intrusion of water through the foundation soil dissolves gypsum which acts as the binding material between soil particles. This phenomenon results in the formation of collapsible soils which can cause serious damages to the dam structure. The failure of Mosul Dam, with a reservoir as large as 11 billion cubic meter of water, can be catastrophic. In the past, Mosul Dam Authorities have been remediating the soil foundation by injecting cement mortar. This method has been proved not economic; therefore, new, more efficient, methods are desperately needed.This research study focuses on finding practical methods to remediate collapsibility of gypsiferous soils by improving their geotechnical properties. This study presents remediation of collapsible gypsum-rich soil by grouting. Three types of stabilizer materials were used to make the grout; (1) sodium silicate (Na2 O3 Si) which is a well-known chemical soil stabilizer, (2) bentonite slurry, and (3) silicone oil. The purpose for using these stabilizer materials is to provide an impermeable layer (waterproofing coat) around the gypsiferous soil particles and to fill the voids that may occur in the soil as a result of gypsum dissolution when subjected to water.A series of double oedometer (collapse) tests and direct shear tests were carried out on gypsiferous soils before and after remediation by grouting. The results show that the soil compressibility decreases in the grout-treated gypsiferous soil by reducing volumetric strain. Consequently, the potential for collapsibility decreases too. It was also shown that grouting, increases the shear strength of the soil at confining stresses smaller than 250 kPa by increasing the cohesion combined with a slight reduction in the internal friction angle.INTRODUCTIONGrouting is one of the ground improvement techniques which is often used to improve the loose foundation soils. Bruce (2003) provides step-by-step procedures on using grouting techniques for sealing dams and other water reservoirs. Grouting can be classified as permeation grouting, compaction grouting or hydraulic fracturing. Permeation grouting is an effective way to send the grout into the ground without disturbing the soil structure, i.e. free flow of grout into the soil voids where grouting is accomplished by injection of a fluid-like material that is capable of forming a gel and binding the soil particles together. Grout materials may be solution grouts or suspension grouts. The permeation grouting technique is generally used to minimize ground permeability and to control ground water flow, but it can also be used to strengthen and harden the ground (Raman et al., 2012)."

Jan 1, 2017

By Abdelmalek Bouazza, Aamir Mahawish, Will P. Gates

Bio-grouting by means of microbial induced calcite (calcium carbonate) precipitation (MICP) to improve mechanical properties of granular soils has gained much attention in recent years. The biogrouting process offers an alternative and environmentally friendly approach to conventional soil improvement techniques, such as cement. Bio-grouting by urea hydrolysis has been extensively applied to tackle various geotechnical problems. However, it has yet to be applied to improve engineering properties (compressive strength) of a coarse cohesionless material with the aim using it as sand/stone columns within soft and very soft soils. This paper investigates the effect of using light, moderate and heavy biochemical treatments on the unconfined compressive strength (UCS) of coarse sand columns. In addition, the microstructure of the bio-cemented coarse material has been analysed by X-ray computed tomography (XRCT). The experimental results revealed that the UCS could reach up to 200kPa, 1000kPa and 5500kPa for light, moderate and heavy bio-cemented coarse sand columns, respectively. The microstructure investigations showed that the deposited calcium carbonate can be identified using XRCT imaging and can be associated with the gain in UCS values. Various microstructure properties, such as void ratio, dry density and porosity were also identified and compared with the laboratory data.

Jan 1, 1900

By Matthias Pulsfort, Hanna Nissen, Markus Herten

An insufficient integrity of cast in-situ bored piles can lead to a reduction of the load bearing capacity and may require cost intensive repairs. Reasons for an insufficient pile integrity are linked to the construction process, mainly to poor concrete quality leading to bleeding and segregation of the fresh concrete. Moreover, the entrapment of soil and an insufficient concrete cover can pose a problem. Knowledge about the time-dependent development of the fresh concrete pressure during the construction process of bored piles is needed for a better understanding of the underlying processes causing these defects. Therefore, pressure measurements were carried out on different construction sites with pressure cells being installed at different depths along the reinforcement cage. The measurements revealed the maximum pressure acting on the surrounding soil. The achievement is a better understanding of the effects of the concrete placement specifically and the construction process in general on the surrounding soil to reduce the risk of pile imperfections.

Sep 8, 2021

By Paolo Cavalcoli, Federico Pagliacci

"As opposed to the static functional recovery of existing structures, the construction of infrastructures in an urban environment, when combined with complex geological situations, often involves building foundation structures, whether circular or rectangular in section, through rock formations or chaotic strata (sand and gravel with cobbles). Until a few years ago, these formations or strata were sometimes an insurmountable constraint on traditional foundation installation techniques. The difficulty in overcoming these geological situations is sometimes added to the increasingly frequent need to reach depths that were unimaginable just a decade ago. These are real challenges for those carrying out these works and for those manufacturing the necessary equipment. There are two main methodological approaches to these problems, that can be summed up in the rhetorical figure of ""David and Goliath"": cunning versus force. In reference to the case studies in this article: the permanent retaining walls for the Copenhagen Metro, and the structural repairs to the Arapuni Dam in New Zealand and the Wolf Creek Dam in the U.S., we will describe the foundations constructed in presence of rock using combined small-diameter direction drilling solutions, associated with their enlargement up to the project’s size, at depths exceeding 300 feet. Finally, a case study will be presented on the implementation of a large cross-section of an excavation in the rock, at depths greater than 800 feet.IntroductionAs opposed to the functional recovery of existing structures, the construction of infrastructures in an urban environment, when combined with complex geological situations, often involves building foundation structures, whether circular or rectangular in section, through rock formations or chaotic strata (sand and gravel with cobbles).Until a few years ago, these formations or strata were sometimes an insurmountable constraint on traditional foundation installation techniques. The difficulty in overcoming these geological situations is sometimes added to the increasingly frequent need to reach depths that were unimaginable just a decade ago.These are real challenges for those building these works and for those manufacturing the necessary equipment. There are two main methodological approaches to these problems, that can be summed up in the biblical figures of ""David and Goliath"": cunning versus force. In the engineering field, the force is summarized in the use of ever-larger drilling equipment in terms of installed power, weight in working conditions, winch and rotary capacity."

Jan 1, 2015

By Md. Nafiul Haque, Murad Y. Abu-Farsakh, Chris Nickel

"This paper presents the results from a pile load testing program for a bridge construction project in Louisiana. The testing includes two 54-inch open-ended spun cast concrete cylinder piles (OECP), one 30-inch open-ended steel pile (OESP), and two (30-inch and 16-inch) square prestressed concrete (PSC) piles driven at two locations with very similar soil conditions. All the test piles were instrumented with vibrating wire strain gauges to measure the load distribution along the length of the test piles and the skin friction and the end bearing were derived from strain gauge measurements. High strain dynamic load tests (HSDLT) were performed on all test piles at different times after pile installations to quantify the amount of setup with time. Static load tests were also performed on the PSC and open-ended steel piles. Due to expected large pile capacities, the statnamic test method was used on the two open-ended cylinder piles. The pile capacities of these piles were evaluated using various CPT methods (such as Schmertmann, De Ruiter and Beringen, LCPC, COFS methods). The result showed that all the methods can estimate the skin friction with good accuracy; but not the end-bearing capacity. Setup was observed for all the piles, which was mainly attributed to increase in skin frictions. The setup rate parameters “A” [The “A” parameter is defined as the rate of increase of pile capacity ratio (Rt/Rto) per log cycle of elapsed time] were back-calculated for all the test piles and the values were between 0.31 and 0.41.INTRODUCTIONDue to greater efficiency (capacity to weight ratio) of the pipe piles, open-ended piles are a viable option to solid piles. However, the behavior of open-ended piles is more complicated compared to the close-ended piles owing to possible formation of “soil plug” inside the open-ended pile. Many researchers have analyzed the behavior of both types of piles for different purposes; however, very few studies in the literature offer the side-by-side comparison of the close-ended and open-ended piles."

Jan 1, 2017

By Yazn Khasawneh Ph. D. P. E., Will Tjaden, Spencer E. Ness P. E., Mohammed Nasim Ph. D. P. E.

Wind turbine components undergo many loading cycles during their operational life. Additionally, wind turbines may undergo extreme loading conditions from natural hazards, mechanical failures, or emergency stops. Current design practice for the foundations of wind turbines accounts for these complex loading conditions through a simplified pseudo-static approach based structural loading combinations. A rotational stiffness for the foundation is estimated from the pseudo-static analysis and then compared to an acceptable minimum rotational stiffness provided by the turbine manufacturer. These minimum rotational stiffnesses are based on dynamic analysis of the tower and nacelle system with the foundation represented as linear springs. This approach provides a reasonable approach to the foundation design but does not accurately capture the true dynamic performance of the entire soil-foundation-tower-nacelle system. This becomes especially important for pier-type foundations, which are being more commonly used to support modern and future generations of larger turbines. Additionally, the dynamic performance of the foundation will vary as the adjacent soil undergoes a large number of loading cycles of varying strain magnitudes. In this study, the full turbine-tower-foundation-soil system was modeled using finite element methods. An advanced non-linear soil constitutive model and dynamic loading time histories were used to investigate changes in stiffness of the soil, and the possible impact on the dynamic response of the system. Results were compared to conventional design methodologies with the goal of reducing foundation capital costs while avoiding increases in O&M costs and which can lower the LCOE of wind energy.

Oct 1, 2022

By I. D. McPherson, Dominic P. Mahoney

The Metro Sports Facility is currently under development in Christchurch, New Zealand and is a key Anchor Project in the city’s post-earth quake recovery. When completed it will be largest indoor sports and swimming pool complex in New Zealand, with a building footprint in the order of 22,000m2. The site is underlain by poor performing soils comprising interbedded layers of soft compressible silts and loose liquefiable sands to over 20m depth. The site is typical for Christchurch with a shallow groundwater table and artesian conditions. The site performed poorly during the 2010-2011 Canterbury Earthquake Sequence with extensive liquefaction, and associated ground damage. To provide a resilient and economical foundation system for this key development project, deep ground improvement comprising of a uniform grid of some 7,200 stone columns in conjunction with robust shallow foundations has been adopted. This paper discusses the geotechnical site constraints, and ground performance under earthquake loading and describes the various options considered for the development. The foundation option selected, the design considerations of the adopted stone column ground improvement, and foundation solution are described in detail, as well as, construction observations. The paper aims to provide insight into an urban large-scale ground improvement project for the engineering practitioner.

Nov 1, 2022

By Maurizio Siepi, Bruno Vingiani, Claudio Asioli

"The article describes an emergency rehabilitation intervention executed at Buyo Dam, in Ivory Coast, to intercept a significant water seepage occurring through the foundation of this zoned earthfill retaining structure constructed in the late Seventies. To solve the problem, a 800 mm thick, 400 m long impervious cut-off wall (COW) was constructed on the right side of the embankment, operating from the dam crest and with the reservoir almost at its maximum level. The use of an innovative pre-mixed self-hardening grout, with a target hydraulic conductivity coefficient (k) lower than 10-9 m/s, was considered the only way to match the tight working schedule and the strict requirements for the filling material of the COW.Presentation of the Hydroelectric Scheme of BuyoThe hydroelectric scheme of Buyo, located at 6°14’28” N 7°20’45 W on the Sassandra River, in Ivory Coast (Figure 1), was built in the late Seventies for agriculture and power generation. With a reservoir of 8.3 billion m3 and an installed power capacity of 165 MW, enough to supply electricity to 111,000 homes, it represents an installation of great significance for this West African country."

Jan 1, 2016

By Heman Manchanda, Sandeep Sharma

Several infrastructure projects are in various stages of construction and planning in India and almost all of them involves open ground excavation extending to varying depths. These structures are generally multipurpose and fulfil several needs of the society, their failure can be catastrophic. The design and construction of deep open excavations is generally associated with a high level of risks due to a whole series of uncertainties involved, and the success of such projects depends on various factors including appropriate evaluation of ground behavior and response to excavation stages, correct choice and analysis of construction supports, control of ground water flow during excavation, etc. One of the most critical amongst all these is ground water flow during construction and stability of underground excavation depends to a large extent on ground water control. This paper uses numerical studies for the assessment of the potential impact of ground water and ground water movement for the design of underground deep structures. The studies are being conducted using PLAXIS 2D finite element software and analysis all construction stages to which an open underground excavation shall be subjected. The paper discussed in detail the impact of water table fluctuations and comparative evaluation of different water flow conditions – a) Different Stages of excavation in line with the construction sequence (Phreatic), b) Coupled flow analysis (Transient- 1 year and 2-year duration) and c) Steady state flow conditions. The paper also covers seepage calculation and design of dewatering system.

Sep 1, 2022