Search Documents

By L. H. Simons, H. H. Spain

I NT RODUCTION Theory indicates that linear water-floods should exhibit scaling and stabilization properties in both oil-wet and water-wet porous media'. Experimental verification of these proper-ties in oil-wet media was obtained some time ago', and more recently, Perkins', employing a high permeability unconsoli dated sand and a low oil-to-water viscosity ratio, has obtained flooding data in a water-wet medium which follow the pattern of scaling and stabilization. Also, Root and Calhoun3 have found similar trends in the displacement of gas by liquids from unconsolidated sands. In general, however, the experimen-tal evidence appears still somewhat conflicting since scaling and stabilization of water floods in water-wet media has not been observed in most of the studies to date'.".'. The purpose of this paper is to provide a more comprehensive picture of waterflood behavior in water-wet media and to corroborate the validity of the scaling and stabiliza-tion concepts. The need for differentiating between the intrinsic nature of water-oil displacements inside a porous medium and perturbating secondary end effects is discussed, pertinent experimental procedures are outlined and the results of flooding tests conducted at low and at high oil-to-water viscosity ratios on con- solidated, water-wet Alundum cores are analyzed. END EFFECTS IN WATER-WET MEDIA Outlet End Effects The peculiar feature of the outlet end effect in water-wet cores is that it not only results in an excessive wetting phase saturation at the outflow face,'.' but that it also retards the moment of water breakthrough: i.e., causes an undue delay in the appearance of water in the produced effluent. Conditions existing in a water-wet core when water first arrives at the outflow face are schematically shown in Fig. 1. At this flooding stage the saturation distribution, Fig. la, has not yet been distorted by the outlet end effect. A water-invaded pore at the outlet core face, opening into the oil-filled void space between the end of the core and the end plate of the flooding cell, is illustrated in Fig. lb. The curvature of the water-oil interface is concave toward the outlet, and the pressure on the water side of the interface is lower than on the oil side by an amount equal to a certain capillary pressure (Fig. lc). Before the water (of this particular pore) can be produced from the core, it is apparent that the pressure in the water phase must exceed that in the oil outside the core. Accordingly. when water first reaches the outlet face, it will not leave the core but will accumulate inside, and only oil will be produced. Eventually, as the water injection is continued. sufficient pressure is built up in the water to reverse the curvature of the interfaces in the outlet pores, and only then will water be produced from the core. This stage, illustrated in Fig. 2. corresponds to the conventional "water breakthrough" observed in flooding experiments. For purposes of discussion, it is convenient to distinguish between the flooding stage at which water first arrives at the outlet face of a core (Fig. 1) and the stage at which water is first produced from the core ( Fig. 2). The former will be referred to as "water arrival" and the latter water breakthrough. In oil-wet media

The STATE MINERAL SUMMARIES publication provides estimated data and summaries of mineral activities at the State level for 1990. Most of the estimates are based on nine months data. These summaries have been prepared in cooperation with State geological surveys or related agencies. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State Activities field office.

Jan 1, 1991

The title of this address was selected before I had an opportunity to consider in detail the matters that I would like to discuss. Accordingly, I chose a very broad subject-so broad indeed that it would be foolhardy for me to attempt to deal with more than a few aspects of it. I do not propose to touch. at all on the developments to date of our mining and metallurgical enterprises, beyond paying a sincere tribute'to the skill and enterprise of those who have established an international reputation for Australian mining and metallurgy. I would rather look ahead and discuss certain factors that will play a decisive part in the future development of our mineral resources. I do this in no dogmatic spirit, and I hope that my remarks may lead to discussions which will stimulate action where it is needed.In recent years my colleagues and I have been forced by circumstances to give consideration to problems in the fields of mining and geology, and in process metallurgy, which lie outside the scope of our own research work. People come to us with metallurgical problems because they know of no more appropriate place to go, and it is distressing to have to inform them that it is nobody's job to offer them advice and assistance. I want to suggest to your Institute that it should press strongly for the provision of properresearch facilities for the mining and metallurgical industries, such as aready exist in most enlightened countries. In such countries, those connected with the development of mineral resources are able to obtain information and advice from Geological Surveys, Mines Departments or Bureaux of Mines, which offer far more comprehensive services than are available in this country.Before discussing specific technical problems of the mining and minerals industries, I shall enunciate certain general principles that I believe should be followed in respect to the technical side of the development of all Australian industries. The problem can, I suggest, be considered in three parts-technical education production, and research. I shall confine my remarks mostly to the research aspect, for it is with this that I am most familiar.For the efficient development of any industry in Australia, it is essential firstly that We should learn what is going on abroad, and secondly that we should simultaneously conduct independent research. In the latter sphere the Governmeht'departments and the private companies' or groups of companies should have complementary functions, the former concentrating on problems common to a number of companies or industries, and the latter on their oWn individual problems. It is essential to the continued existence of Australian industry that both company and govern...

Jan 1, 1944

By Alastair C. Torrance

"A brief review of the Australian mining industry is given followed by a more detailed treatment of a study of the influence of primer Size on explosive performance. This is based on a joint research programme conducted by BHP Central Research Laboratories and Dyno Wesfarmers Ltd and examined the effect of the size of cast primers on the run up and steady state detonation velocitiesof ammonium nitrate based explosives as a function of blasthole diameter. The field trials examined a numter of the Dynamo 'Westfarmers HDF series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the iun up velocity of 187 mm diameter ANFO charges is negligible using cast primers as small as 150g. However, emulsion and watergel explosives did exhibit run up in both 187 and 3:1mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blashole diameters"

Jan 1, 1991

By Dennis R. Dolinar, Gabriel S. Esterhuizen

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

By Thierry Bernard, Guy Gagnon

Blasting at very close proximity to urban areas is typically a situation where both local communities and mining stakeholders get nervous. The context becomes logically even more tensed when the blasting operations have to be performed above an old underground mine. When mitigating subsidence risks requires firing the largest possible shots, the nuisance control (flyrock, vibration, and noise) required by local and national regulations, contrarily urge for being more conservative.

Jan 1, 2014

By J. J. Wallace

This report describes the initial phase of Bureau of Mines research in the hydraulic mining of bituminous coal. The mining site and equipment are described, and the test procedures and results obtained with a bar-mounted monitor are given. Tests showed that hard Pittsburgh-bed coal can be mined hydraulically from a solid face at water pressures of 4,000 pounds per square inch.4 Coal was penetrated to a depth of 4 feet in 20 seconds with 225 gallons of water per minute coming from a 3/8-inch nozzle at 4,000 pounds per square inch pressure. Some difficulty was encountered in cutting the binders occurring in the coal; it was not possible Lu penetrate directly the overlying draw slate.

Jan 1, 1961

Overview ?Oil Sands Background ?Water Use in Surface Mining ?Tailings Disposal ?Water Balance for Surface Mining ?Implications of Emerging Regulations ?Water Management Framework ?Tailings Performance Criteria (Directive 074)

May 1, 2009

By R. T. Richins

Coeur d'Alene Mines Corporation (CDE) is a precious metals mining company. The company's three mining operations are located In Nevada and Idaho. Collectively, these mines (Rochester in Nevada, and the Galena and Coeur In Idaho) produced about 61,000 ounces of gold and more than 7.5 million ounces of silver in 1991. The company is currently planning the development of two major properties; the Fachinal gold-silver project in Chile and the Kensington gold project near Juneau, Alaska. Fachinal and Kensington hold encouraging potential to significantly expand CDE's gold production during this decade. The permitting process for these two distinctly contrasting environmental settings, project design requirements and regulatory/political circumstances provide the basis for a comparative analysis of licensing and permitting requirements, timeliness of the permitting process and costs in the U.S. and Chile.

Jan 1, 1993

Mr. Murray said: Having recently returned from a visit to America, it may be of interest to members to hear something from me of the mining fields and metallurgical works which I had the opportunity of seeing, and the impressions which I formed concerning general practice and conditions there, as compared with our Australian standards in the mining industry, and in matters generally.The most striking feature of the North American continent is thehuge plan upon which Nature has built, the multiplicity of immense mountains, rivers, and lakes, the snow-covered tops of the former forming reservoirs for the latter during the summer months, being most impressive to the Australian visitor. Starting from Vancouver I travelled east for over 500 miles through the wonderful Canadian...

Jan 1, 1927

By Yifan Ding, Shemek Oginski, Patrick Finn

The Manhattan section of the New York Water Tunnel No. 3 constructed by the Schiavone/Shea/Frontier-Kemper Joint Venture is a $668 million project. The contract includes a tunnel drive of 8.85 km (29,045 feet), tunnel lining of 14.77 km (48,468 feet)and construction of nine shafts ranging in depth from 143 m (469 feet) to 169 m(555 feet). Construction methods for excavation of the shafts are presented including raise bore, ground freezing, soil excavation, blasting, slashing, muck handling, rock support and shaft final concrete lining.

Jan 1, 2007

By Jack L. Taylor

As expected from similar crystal structures and favorable atomic size factors, titanium, vanadium, and molybdenum are completely soluble in one another above the transformation temperature of titanium. The fl phase parameters of the continuous solid solution are shown graphically. Limiting compositions for retained fl phase have been determined. VANADIUM and molybdenum both have body-centered-cubic structures at all temperatures and, from the atomic diameter comparison factor, 3.9 pct, would be expected to form a complete series of solid solutions. The existence of complete solubility has been confirmed by work' at the Jet Propulsion Laboratory. Furthermore, vanadium and molybdenum have favorable atomic size factors to form complete binary solid solutions with the B phase, high temperature form of titanium, which also has body-centered-cubic structure. Pietro-kowsky and Duwez' and Hansen et al." have established the existence of the complete series of solutions in these binary systems. It would be logical, therefore, to expect that p-titanium, vanadium, and molybdenum would be completely soluble in one

Jan 1, 1957

By George Hope, Brigitte Lacouture

"The Red Dog mine has increased mill throughput most years since start-up. Although flotation equipment has been added over the last 10 years, the Red Dog metallurgical performance has been restricted by a lack of adequate flotation capacity. Two reduced tonnage trials conducted in 1997 as well as numerous SAG relines have consistently indicated the potential to significantly increase both zinc concentrate recovery and grade with additional flotation capacity. Later in 1999, a new circuit was designed with increased flotation capacity while simplifying the current circuit, providing for three stages of dilution cleaning, and creating a retreat section. The purpose of the retreat section is to target the more complex particles and allow the chemical environment to be fine tuned for improved iron depression. In total, 21 Outokumpu OK50 (50 m3) mechanical flotation cells and four 3.66 mØ column cells were added to the current flotation circuit. The VIP (value improvement program) mill optimization project is also addressing thickening, water treatment, and power generation issues and has a total budget of US$105 M. Start-up of equipment was phased in to minimize the impact on current operations and the project was completed by the end of 2001. IntroductionRed Dog Operations started production in November 1989. The mine is located above the Arctic Circle in northwest Alaska. It is linked by an 80 km road to a port-site facility where the concentrate is stored. Concentrate is shipped to markets throughout the world during the one hundred days of open seas. As of January 2002, the Red Dog main pit had 38.4 Mt of reserves grading 19.2% Zn, 5.3% Pb, and 102 g/t Ag. Additional reserves and resources contribute an additional 72 Mt at 15.6% Zn, 4.2% Pb, and 78 g/t Ag. Red Dog is a Mississippian to Permian, black shale-hosted, zinc-lead-silver deposit located in the DeLong Mountains, western Brooks Range, Alaska. All the rocks associated with the mineralizing event are considered to be part of the exhalite rock package. Silicification was a dominant component of the mineralizing event and the host shale has been silicified and locally resembles a chert. The major sulphides in decreasing order of abundance are sphalerite, pyrite, marcasite and galena. Most of the deposit’s silver occurs within the crystal structure of the galena. The dominant ore mineral, sphalerite, is very fine grained to amorphous and is commonly intergrown with silica. Ore textures are massive, fragmental, chaotic, veined and rarely show classic sulphide sedimentary layering. The upper portion of the orebody has been physically and chemically weathered. Oxidation has altered the sulphides to sulphates. The zinc and iron sulphates are very soluble and are readily depleted from the weathered cap, while the lead sulphate is residual and is, therefore, enriched."

Jan 1, 2003

By J. R. Ross

A reconnaissance for sources of scandium and a metallurgical investigation of recovery methods for byproduct scandium from uranium mill solutions were conducted by the Bureau of Mines. The work on scandium was undertaken to obtain information on domestic resources and to explore and develop recovery procedures in consonance with the Bureau's long-range program for conservation and wise utilization of mineral resources. The element scandium is widely distributed in the earth's crust in trace amounts, but it seldom occurs as an important constituent in any mineral. An exception is thortveitite, (Sc,Y)2 Si207) a rare mineral that contains various amounts of scandium and yttrium and may contain up to 42 percent scandium oxide (SC203). Knowledge of the chemistry of scandium has expanded rapidly in recent years (1, 4, 9)4 but only fragmentary information is available about the metal because it is still largely a laboratory curiosity without established uses (2, 3). A recent study shows some of the physical proper-ties of the metal are (1) density of 3.05 grams per cubic centimeter) (2) melting point of 1,540° C, (3) hexagonal close-packed structure) (4) hardness of about 50 Brinell (500-kilogram load), and (5) an alloy behavior similar to yttrium and rare-earth metals (2). The price of $2,850 a pound for scandium oxide of 99.9 percent purity and $2,700 a pound for oxide of 99 percent purity reflects the scarcity and complex chemistry of the element.

Jan 1, 1962

By R. C. D. Phillis

The management of critical resource inventories is an important productivity lever and a significant risk factor?risk in the sense that poor resource availability lends itself to disempowerment of workers, unsafe work practices, wasted spending (high unit costs),and poor quality of work (including mining waste/rework). Most underground platinum mines experience lost blasts that directly lead to reduced productivity. In most surveyed shafts, 30% of lost blasts can be attributed to shortages of critical material and/or equipment. The problem is prevalent despite the existence of conventional transitory surface and underground stores. This paper discusses the introduction of buffer stores as a complementary materials storage system in order to improve health and safety in mines as well as reduce lost blasts. Both quantitative and qualitative results have shown that buffer stores result in dramatic improvements in productivity and are readily acceptable by stakeholders. Keywords Buffer stores, lost blast.

Jan 1, 2011

By Axel Studeny

Geomechanical-numerical methods are an established tool for planning of underground excavations worldwide. By describing the interaction between heterogeneous layered strata and support elements it is possible to determine their suitability. The German hard coal mining industry has more than twenty years experience in investigation and using these parameters to carry out numerical calculations. Today, nearly all excavations (shafts, pit bottoms areas, bunkers, coal faces, development drivages, gate roads etc.) are calculated by geomechanical-numerical tools in combination with empirical planning methods. A high accuracy of planning results, which is a special requirement in the German coal industry with its deep-level longwalls, bedded and weak surrounding strata and multiple seam mining layouts, depends on the extensive calibration of the numerical models, which is achieved by: 1) Taking a large number of underground measurements with empirical evaluation. 2) Carrying out physical modeling. 3) Using the characteristic features of the installed support elements. This paper compares the planning approach used for multiple and single seam mining and presents the advantages of this planning tool. The main focus is on the feasibility of rockbolting as the sole means of roadway support for multiple seam mining operations, though the paper will also look at how the costs can be improved by using a low bolting density in single seam layouts.

Jan 1, 2007

By Peter Swanson

A seismic monitoring network has been installed in western Colorado (USA) in the vicinity of three underground coal mines to (i) distinguish and characterize seismic activity as either mining related or naturally occurring, (ii) implement a real-time event monitoring and notification tool, and (iii) collect data for use in research studies aimed at quantifying impacts from mining-related and natural seismicity. These potential impacts include dynamic rock mass failures such as coal bumps as well as strong shaking in the vicinity of critical structures such as impoundment dams, reservoirs, mine seals, mine openings, and steep slopes. Examples of two damaging seismic events are presented and the mining and geologic factors attending these dynamic failures are described.

Jan 1, 2008

By L. Arnberg, E. Ott

The microstructure of ferrosilicon is important since it controls the disintegration of the material during crushing and thus the generation of fines. Therefore a study of the microstructure formation during solidification of pure FeSi(75wt%Si) and FeSi(75wt%Si) containing 1.2wt%Al and 0.2wt%Ca has been initiated. The material has been cast into rods of 8mm diameter, which have been remolten by induction heating and directionally solidified in a Bridgman apparatus. This allows the temperature gradient and the growth rate to be controlled independently. The temperature history during solidification has been recorded by a thermocouple in the melt. Growth rates have been varied between 5 and 400µms-1 and temperature gradients between 3 and 14°Kmm-1. The microstructures show a large dependence on the solidification conditions. The crack formation in the alloys has been studied and found to be strongly related to the microstructure.

Jan 1, 2004

By D Frantzos, J J. Cotter, H Tammemagi, J B. Codrington, J Kaasalainen, A C. Webster

"Exploshres Technologies International (ED) is developing an instrument called ROCSCAN which isplanned to have broad application in both blasting and rock mechanics. The purpose of this paper is to outllne the background that has led to the development of ROCSCAN, describe its objectives and to present a progress report on the work to date. Some of the potential applications of ROCSCAN will also be reviewed."

Jan 1, 1989

THE machine from which the following results were obtained makes one of a row of seven at work in the Junction North, Concentration Mill at Broken Hill, New South Wales. It consists essentially of a belt for dressing purposes, which travels round two 12-in drums situated at either end of a wooden frame. This frame is supported on wooden legs, and the whole is affixed to two iron castings, one on either side of the frame. A to-and-fro motion is obtained from an eccentric shaft, which, together with the stationary end of the supporting legs, is carried by the iron castings. A belt drive to the forward drum provides a constant rate of travel to the dressing belt.The top half of the dressing belt is supported on 3-in rollers spaced about 12-in centres along the frame of the vanner. A fairly thick dressing belt is used, and no trouble whatever is experienced from the formation of gutters between the rollers.These belts are 28 ft 4 in long, 4 ft wide, 3-16 in thick, and are made of two-ply 32-oz duck, with a coating of rubber on either side. The surface available for dressing is about 10 ft 6 in x 3 ft 8 in- ie, about 38'5 square feet. The machine is driven atthe rate of 245 i-in strokes per minute, while the dressing belt travels at 15 feet per minute...

Jan 1, 1909