Search Documents

By Hiroyuki Sano, Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa, Shin-ya Iwahori

"Pyrometallurgical process using Cu2O-based slag was proposed as a recycling process for copper scrap. However, it is difficult to remove nickel from copper by oxidative refining. Therefore, it is necessary to reduce the concentration of nickel in copper before the oxidative refining. In the present work, the copper enrichment stage in this recycling process, where copper scrap melt is separated into the Fe-C-Cu melt and the molten copper, was taken up and the compositions of both melts were measured. Based on the above results, the distribution ratios of nickel between the Fe-C-Cu melt and the molten copper were calculated. Furthermore, the optimum condition of copper enrichment stage was discussed from the viewpoint of nickel removal and copper recovery. The possibility of recovering 4N-purity copper by using this recycling process was confirmed.IntroductionRecycling is well known as a method for saving resources and reducing environmental damage. More than 99% of copper is used in metallic form - as metal or copper alloys[l]. High-grade copper scrap is directly re-melted and reused, while low-grade copper scrap is transported to copper smelters to be pyrorefined and electrorefined. Nevertheless, a great amount of copper is being stockpiled in the cities and should be recycled in the near future. At that time, the current recycling process will face new problems due to the increases in the recycling rate to the smelters. This includes insufficient combustion heat to melt copper scrap and ·almost no benefit in electrorefining because the scrap does not contain gold and silver. Thus, an alternative pyrometallurgical method for copper scrap refining will be required."

Jan 1, 2000

By Onuralp Yücel, Mehmet Bugdayc, Murat Alkan

"In this study, iron based alloys (Fe-Mo, Fe-Cr-Ni, etc.) were produced by using aluminothermic methods starting from Mill Scales obtained continuous casting processes. Mill scales are an oxidised layer of steel alloys containing iron oxide, which includes + 2, + 3 values, on the surface of slabs and billets occurring during annealing in heating furnace at integrated iron and steel milling plant, and continuous casting unit. In the metallothermic experiments, different ratios of starting mixtures and addition of the oxide powders (Alz03, Si02, CaO, MgO) were examined, and their effects on the metal recovery and alloy compositions were carried out. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques.IntroductionSelf Propagating High Temperature Synthesis process (SHS) has many favour compared to the furnace applications, such as low energy requirement, low cost, very short processing time and simple operation, [l, 2]. In a SHS process, the ignition starts the combustion and propagates throughout the reactant mixture yielding the desired product. However, the disadvantages of the process such as inhomogeneous or unreacted products due to undesirable reaction rates needs to be overcome by changing some parameters such as ignition temperature, particle size, additive, atmosphere etc. [3, 4]. Mill scale is a layer of iron oxide which forms on ferrous materials cooling after being processed in hot rolling or continuous casting plants. Mill scale contains iron (II) and iron (III) oxides, which result in a 70% total iron content in oxide form. Not being able to reuse this material will prevent the raw material entering the production plant from being fully utilized [5]. This study aimed to produce Fe-based alloys via SHS (Self Propagating High Temperature Synthesis) metallurgy which is attractive process technique regarding fast and low-cost production ability of cast alloys by using high metallic iron content by reducing continuous casting mill scale."

Jan 1, 2013

By Thomas E. P. Wechsler

The limiting factor for most pyro-metallurgical processes in secondary cop- per melting is the time required to heat and melt the product. American Combustion's proprietary PYRETRON variable £uel/air/oxygen combustion system improves the throughput of existing scrap melting and heating furnaces for copper and copper alloy production by increasing the rate of heat transfer from the flame to the product. The increased productivity and energy savings obtained from this technology can result in sizable reductions in operating costs for smelting operations.

Jan 1, 1991

By Sang Han Son

The vapor pressures of FeCL2 and ZnCL2 in the FeCL2?ZnCL2 system were measured by the transpiration method at 873K and 9I7K, The vapor pressure data were interpreted to indicate the formation of complex ions in the FeCL2?ZnCL2 melts, It is presumed that the complex molecule FeZnCl4 as well as FeCL2 and ZnCL2 exists in the vapors in equilibrium with molten FeCL2-ZnCL2 mixtures, The activities in the FeCL2-ZnCL2 system are shown a negative deviation from Raoult's law. These results suggest the formation of complex ions such as ZnCL14 in molten FeCI2?ZnCL2 mixtures.

Jan 1, 2003

By Sang Han Son

The vapor pressures of FeCI2 and ZnC12 in the FeCl2-ZnCl2 system were measured by the transpiration method at 873K and 917K. The vapor pressure data were interpreted to indicate the formation of complex ions in the FeCl2-ZnCl2 melts. It is presumed that the complex molecule FeZnCl4 as well as FeCI2 and ZnCI2 exists in the vapors in equilibrium with molten FeCl2-ZnCl2 mixtures. The activities in the FeCl2-ZnCI2 system are shown a negative deviation from Raoult's law. These results suggest the formation of complex ions such as ZnCl42- in molten FeCI2-ZnCI2 mixtures.

Jan 1, 2003

By Denise C. R. Espinosa

Rechargeable lithium batteries are one of the most promISIng technology in battery development. Although Li ion batteries have been used as an alternative to the more polluting and less performing Ni-Cd batteries, Li ion batteries have limited life and their disposal is uncertain. It is imperative that valuables from wastes, such as lithium, should be recovered. The main objective of the present work was to characterize secondary lithium batteries for cellular phones. This was done using unit operations of mining processing, x-ray diffraction (XRD), chemical analyses and the rmogravimetric analysis (TG). The unit operations were hammer mill grinding, knife mill grinding, size separation and magnetic separation. After the hammer grinding process, the plastic cases were almost intact, however, they have released the cylindrical lithium batteries themselves and these parts correspond to 70% of the total battery weight.

Jan 1, 2001

By R. E. Johnson

The No. 3 reverberatory furnace at Phelps Dodge. Corporation's Morenci, Arizona copper smelter first received oxygen from a new oxygen plant during October 1982 and began operation with oxygen-fuel and oxygen sprinkle smelting burners which burn concentrate with oxygen. The furnace was completely converted to roof-mounted oxygen-fuel firing in October 1982. All conventional air-fuel bridge wall burners were extinguished at that time. The novel arch-mounted oxygen sprinkle smelting system began continuous operation April 1983. Since startup, unit fuel requirements decreased and furnace throughput significantly increased. Furnace off gas SO2 strength increased from an average of 1.5% SO2 to an average of 20% using only oxy-fuel burners. Oxygen sprinkle burner operation also has given excellent results, with the furnace off gas strength increasing to 35%-60% S02. There has been a reduction in overall arch temperatures, an increase in matte and slag temperatures, and a lowering of furnace bottom buildup with oxygen smelting. Furnace off gas is blended with converter off gas and treated in a sulfuric acid plant.

Jan 1, 1983

By V. R. Voller

"The World Wide Web (the web) provides a very useful resource for the enhancement of teaching and research dissemination. This paper advocates that researchers take control of this resource and become actively involved in creating web content. Two examples of the use of the web in a materials setting is provided. The first illustrates how a concept quiz for teaching can be developed. The second shows how a materials processing model can be run in real time over the web. The paper closes with a summary of some resources that can be used to create web materials.IntroductionA recent copy of a newspaper advertisement read""Share what you know, learn what you don't""This neat phrase sums up a powerful teaching and research philosophy. In an educational setting a prime motivation for research is to uncover the unknown and venture in directions previously uncharted. The balance to this search for knowledge should be a desire to share that knowledge with others; whether it be with students in the classroom or research colleagues in a wider setting.The .World Wide Web and its associated multi-media software offer a perfect platform for researchers to share their knowledge with an extremely wide sector of the research community. To enable the use of this resource researchers must take the power that the web offers them into their own hands and create products that take maximum advantage of the medium. It is key that researches at the forefront become directly involved, otherwise a potential powerful medium will not realize it's true potential, and colorful products with no core content will proliferate. The object of this paper is to outline two ways in which the web can be used to enhance teaching and research objectives."

Jan 1, 2000

By Shadia J. Ikhmayies

Polycrystalline CdTe thin films were prepared by vacuum evaporation on glass substrates. The I-V plots which were linear were used to find the resistivity. A value of 2.10×106 .cm was obtained. The transmittance was measured in the wavelength range 400-1100 nm. The bandgap energy was found to be 1.48 eV. X-ray diffraction pattern shows that the material deposits in the zinc blend structure with one strong reflection from the C(111) plane. The scanning electron microscope image shows a uniform surface with a small density of large (mµ1£) grains scattered on the surface.

Jan 1, 2009

By Pengfu Tan

NiModel, a thermodynamic model, database and computer program, has been developed to predict the distribution behavior of Ni, Cu, Co, Fe, S, O, As, Sb and Bi, and heat balance in the nickel pyrometallurgical processes such as Outokumpu flash smelting, Outokumpu direct high-grade matte smelting, INCO flash smelting, and Peirce-Smith converting processes. In this model, as much as 16 elements (Ni, Cu, Co, Fe, As, Sb, Bi, S, O, Al, Ca, Mg, Si, N, C and H) are considered. The compositions of matte, slag and gaseous phases, and heat balance are calculated using the thermodynamic data and the activity coefficients of the components derived from the experimental data. The model predictions were compared with the known industrial data from Kalgoorlie Nickel Smelter in Australia, Outokumpu Harjavalta Nickel Smelter in Finland and INCO Metals Company in Canada, and an excellent agreement was obtained. In this paper, the applications of NiModel in the nickel pyrometallurgical industries have been presented. NiModel has been used by Jinchuan Group Limited in China.

Jan 1, 2004

By David T. Bunney

In .December of 1987, International Mill Service, Inc. signed an exclusive licensing agreement with Tetronics Research & Development Co. Limited of Faringdon, Oxfordshire., England to commercialize plasma technology which had been demonstrated in an EAF dust processing application. The intent of the process is to reduce and volatize the zinc, lead and cadmium oxides inherent in EAF dust and collect these elements as metals in an ISP (Imperial Smelting Process) zinc splash condenser, and to render the resultant slag an inert, non-hazardous material. With these objectives in mind, IMS started commissioning facilities in 1989 at Florida Steel in Jackson, Tennessee and Nucor-Yamato Steel in Armorel, Arkansas. This paper will address the commercial development and progress of the technology at these two installations. Process Description In the EAF steelmaking process typically the off gas stream is cleaned by some form of baghouse. The particulate collected is known as Electric Arc Furnace dust and has been designated by the U.S. EPA as hazardous waste number K061, once it leaves the collection system. This designation was given to the material due to the high toxic concentrations of lead and cadmium (nickel and chromium for stainless EAF dusts) inherent in the dust. IMS' method of operation is to locate the facilities on the client mill's property adjacent to the baghouse. The dust is transported directly to IMS via a closed conveyance system. This method enables the technology to be an additional processing step in the steelmaking process. Once the dust has been transported to the IMS facility, it is fed, metered and mixed mechanically in the feed conveyance system with a carbon reductant (typically coke breeze). The carbon reductant is approximately 10% of the dust feed rate. This mixture passes through the feed system and enters the furnace

Jan 1, 1992

By R. Craig McClung

Contrary to other sulfide minerals, where recovery is principally liberation controlled, the recovery of molybdenite is more complex. It is this complexity that initiated a geometallurgical investigation of molybdenites from Bingham Canyon. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes have on recovery. All samples were analyzed using normal mineralogical techniques. The results reveal the presence of two distinctly different types of molybdenite. These have been identified as the two polytypes of molybdenite: i.e. hexagonal (2H); and rhombohedral (3R). The 2H-polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the current pit bottom. The 3R-polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance and are concentrated along the margins of the current pit. Concerning their metallurgical behavior, each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. The 2H-polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This results in the production of a high quality concentrate under normal operating conditions. The 3R-polytype, by comparison, is difficult to grind and kinetically “slower” floating with surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R-polytype, modifications to the normal operating parameters may be necessary to improve recovery. This investigation highlights the necessity for understanding the mineralogical characteristics of any economic mineral(s), as these will have a direct impact on recovery.

By Zhang Hengzhong

Based on thermodynamics of surfaces and a proposed two-dimensional state equation for surfaces, the relationship between the surface tension (Y) of a solution and the activity (a1) of its component (i) was derived: (1/Y)r2-.¬E (ai/Yl) The derived equation was verified with reported experimental data of water-alcohol systems and water-acetone system, the calculated results showed astonishing coincidence with experimental. Applications of the equation to the five matte systems Cu2S-FeS, Ni3S2-FeS, FeS-PbS, Cu2S-PbS and FeS-Cu22S-PbS also demonstrated that at given matte compositions the calculated surface tensions agreed with experimental fairy well.

Jan 1, 1993

By K. Sarveswara Rao

"Any innovative approach made in non-ferrous metallurgical industry centers upon developing new processes, saving materials, improving production quality, and bornagain materials. Aqueous processing is commonly used to treat lean grade or more complex ore bodies. Its sustenance largely depends on energy and environmental compliance including water and wastewater management. The present paper focuses the importance of using particle size distribution and surface area measurements during ammoniacal dissolution of a Cu-Pb-Zn sulphide bulk concentrate and with an overview of the effect of water salinity on the process chemistry and residue mineralogy. Accordingly, an effort is made here to discuss the emerging perspective and highlight the recent successes and trends in terms of energy savings in non-ferrous hydrometallurgy.IntroductionThe nature and structure of the global energy industry is likely to change significantly in the 21st Century. Rabago et al [1] have comprehensively discussed how the mining and minerals industries can adapt to the challenges and opportunities posed by trends and drivers in global energy use. According to the authors, the drivers of sustainability include water, efficient energy use, climate modification, transportation technologies and energy security. Sustainability and competitiveness for the minerals industry will depend on natural capitalism, resource efficiency, new processes, saving materials, improving production quality, born-again materials and the solutions economy. Based on this motivation, the theme of the present paper is centered upon applications as relevant to energy and sustainable development in non-ferrous hydrometallurgy."

Jan 1, 2009

By I. C. Howard, E. J. Palmiere

"Heat transfer and friction in hot flat rolling have traditionally been characterised by an average heat transfer coefficient (h) and an average friction coefficient (p.). However, the presence of oxide scales and asperities at the interface question the use of such averages. The apparent irregularity and lack of pattern of interactions at the interface has prompted this present investigation to move away from averaged h and 11 values, and to study their local evolution based on probabilistic rules. The approach is based on the probability of finding the workpiece surface in a specific configuration at a particular instance of time in the roll gap. These rules are based on observations of surface phenomena such as scale behaviour during hot rolling. The model is implemented using user-subroutines integrated with the commercially available finite element program ABAQUS™. The results show the strong dependence of h and u on the local scale interactions. In particular, the effect of scale thickness, material behaviour and processing conditions on the evolution of hand 11 are discussed. Finally, the development of a Cellular Automata based Finite Element (CAFE) model is proposed to model the combined interfacial phenomenon of friction and heat transfer at the tool-work piece interface.IntroductionIntricate interactions between process variables in hot rolling of steels make it a challenge to the modelling community. For a given material and geometry combination, reducing interfacial power losses can increase the efficiency of the rolling process. The roll-strip interface, therefore, forms the critical zone and is currently the domain of intense investigation, especially to characterize interfacial frictionl • 2 and heat transfer3 • 4 . These interfacial phenomena are inter-related and cannot be studied in isolation. However, very few mathematical models4 • 5 combine an analysis of friction and heat transfer and deformation of the strip-roll interface taking into account the role of asperities and oxide scales."

Jan 1, 2001

By Luciano E. Ramírez, Jesús L. Valenzuela, José R. Parga

"An innovative process for removing copper cyanide complexes including silver and zinc from cyanidation circuits has been developed. The technology was based on the inducing the nucleated precipitation of copper and silver in a tube serpentine reactor, using sodium sulfide as the precipitate and sulfuric acid as pH control. The results showed that pH had a great effect on copper cyanide removal efficiency and the optimum pH was about 3 to 3.5. At this pH value copper cyanide removal efficiency could be achieved above 97 and 99 % ,when influent copper concentration ions were 650 and 900 ppm respectively. In this process (sulphidizaton-acidification-recycle-thickening), the cyanide associated with the copper cyanide complexes is released as HCN gas under weakly acidic conditions, allowing it to be recycled back to the cyanidation process as free cyanide. This system was successfully commercial applied at Minera William in Mexico.IntroductionThe recovery of gold and silver from minerals and concentrates with cyanide is an important hydrometallurgical process, which has been studied for more than 124 years. Patented by MacArthur in 1888 [1], the process relies on the fact that gold dissolves in aerated cyanide solutions to produce the gold cyanide complex. The stoichiometry by wich this reaction occurs is known as the Elsner equation as shown here. Silver is accomplished in the same fashion."

Jan 1, 2012

By Alistair Burrows

Situated in the oblast of East Kazakhstan, the Ust-Kamenogorsk Metallurgical Complex has spent the past twenty years renovating and remodelling itself as a modern polymetallic sulphide smelting facility, and a regional centre of excellence for custom smelting. Along the way there have been changes to the company structure, introduction of new technologies, investments in expanded capacity, environmental improvements, and addition of new metal products and by-products to the site’s repertoire. These changes have been gradual and incremental, but taken together they represent a significant contribution to placing Kazakhstan’s sulphide smelting industry on a strong foundation for enduring success in the international custom smelting market. In achieving these changes, a workforce that was historically isolated from much of the world now has recognised expertise, internationally competitive skills, and confidence to embrace the future. Further improvements in energy efficiency, environmental compliance and polymetallic processing capabilities are challenges that UKMC stands ready to face.

By M. E. Coleman, G. Money

"Clyde Materials Handling is an established customer-driven solutions provider, which utilizes its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries.With over 30 years experience in the process improvement industry, Clyde Materials Handling has helped their global customer base transform the way in which they operate their processes, which has enabled them to generate sustainable economic benefit and maintain their positions as leaders in their respective markets.Clyde Materials Handling has supported operators within the metals market by developing and deploying pneumatic conveying and pneumatic injection technologies. These environmentally supportive and sustainable solutions have been used to transport raw materials within operating facilities, from storage to silo, as well as injecting these materials directly into the heart of production processes.Clyde Materials Handling has worked closely with their customers, such as Codelco in Chile, where their pneumatic solutions have been used to inject a consistent, pulseless and accurate flow of copper concentrate into a bath smelter, which has helped to fuel the operational capacity, availability and productivity.This paper will discuss and highlight the ways in which pneumatic injection technologies, created by Clyde Materials Handling, and applied in partnership with their customers, have helped to improve the operational performance of the production processes of operators across the non-ferrous metals markets with specific reference to applications in the Peirce Smith Converter.Clyde Materials Handling has applications injecting Electronic Scraps, Dusts, Reverts, and other additives to the Peirce Smith Converter. They also have experience of modified PS Units used for Slag Cleaning. There experience with the Codelco Teniente Converter is also directly related to this area of operation."

Jan 1, 2009

By Yuanbing Ling

Keywords: Calcium sulfate, Sulfuric acid, Phase transformations, Thermodynamic analysis As part of a boarder research project, seeking the development of a cost-effective process for direct production of the high value material, -calcium sulfate hemihydrate, from sulfuric acid at atmospheric as opposed to elevated pressure conditions, the fundamental work presented here has been undertaken. This includes experimental monitoring of phase transformation reactions and thermodynamic analysis of the relationships among the various phases, namely, calcium sulfate dihydrate, hemihydrate and anhydrite in aqueous sulfuric acid solution at temperatures ranging from 20oC to boiling point.

Jan 1, 2004

By O. A. Ogunseitan

The contamination of aquatic ecosystems by mercury wastes is one of the most serious forms of environmental pollution associated with the metal mining and electrochemical industries. The transformation of inorganic mercury to alkylated species is a reversible bacterially-mediated process. The production of methylated mercury is of ?major public health and eco-toxicological concern because these forms of mercury are highly toxic ?and they bioaccumulate in aquatic organisms. We determined the response of the genetic determinants of mei:cury transrormation by Pseudomonas species (that predominate in contaminated soils and sediments), to the concentration and species? or available mercurfiations. By combining selective isolation and gene. ?probe techniques, the intrinsic genetic potential for mercury detoxification in a contaminated environment ?can be estimated. We determined that genetic units required for mericury volatilization (merA ?for mercuric reductase) are naturally amplified in response to mercury. Mercury-resistant bacteria that tolerate up to 100 ug Hg(Il)/ml of medium contain about 10 times more DNA fragments encoding merA than in unadapted bacteria. The exposure of bacteria to methylated.Hg (10 ug/ml lake water) produced increases (up to 10 times) in .genetic units, and higher levels of genetic expression (up to 50 times) per ml of lake water for the mercury reductase system, than on-induced lake water. The findings suggest that in environments where methylated Hg may accumulate as a result of bacterial activity, the reverse reaction which leads to the removal of mercury through volatilization from the system, may be achieved by inducing genetic ?amplification and expression of the mercuric reductase gene system.

Jan 1, 1991