Search Documents

By Jorge Cárdenas, José Luis Hurtado

The critical distance determination test through direct recording for the mine in Phase 03 was carried out in January 2024, and in it the vibration and pressure models were obtained for the Sedimentary breccia unit. The method of obtaining the records is based on the capture of individual pressure waves generated by distant loads, sequenced in periods of 600 ms for easy identification. The test set up corresponds to a variation of that used to obtain the vibration model, and uses 08 wells for loads and 04 for instrumentation. The results apply a safety factor of 1.2 and 1.5, being 16,000 PSI and 13,250 PSI respectively. The values are valid for any distance greater than 5.5 m, this being the minimum established between wells for loads according to the configuration defined in the field, also considering that in 5.0 m of instrumentation the section of the drill hole with the sensor called S1 collapsed. The results of the analysis of the test, generated with Heavy Anfo 82 explosive, with a final density of 1.15 g/cc, are presented. The results of the modeling and generation of the graphs and tables presented show behavior in line with the concept of scaled distance. It is important to consider that in water conditions there is a high impact by the condition, which causes the records to be higher than those expected in dry conditions and present less variability. It is for the above reason that the row corresponding to distance with safety factor 1.5 is declared valid. The results are only valid for the rock analyzed, whose medium is homogeneous and constant in terms of lithological composition and that present similar resistance characteristics, fracture frequency and water table levels. As future steps, the objective is to quantify the increase in pressure generated between wells by analyzing time and sequence factors. This analysis aims to explain the occurrence of dynamic pressure events in areas where critical safety distances are observed.

Jan 21, 2025

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer

The environmental problems such as vibration, and air blast are often faced, and discussed on mining, quarrying, civil constructions, shaft-tunnel, pipeline, and dam operations where blasting is inevitable. It is necessary to establish national standards towards to minimize the environmental problems induced by blasting and judicial matters in our country as it is in USA, EU countries and the other developed countries. This necessity and the obligatory of accepting the European Union criteria for Turkey that has started the procedure of joining to EU emphasize the importance of this study. In other words, the establishment of a particular national standard related with this subject is inevitable for Turkey. This will be possible only by studying, applying scientific methods and techniques by the experts.

Jan 1, 2010

By R. F. Favreau, Patrice Favreau

In many quarries and construction sites visited by the authors over the last 50 years, the latter have observed muck piles from blasting with explosives, which included numerous large blocks, in some cases of dimensions larger than the input to the crusher. The names of these sites cannot be given in the article because the owners insist that data obtained on such visits be kept confidential. Often the blasters felt that the natural fissures in the rock would compensate for the use of a low powder factor, and they asked the authors to explain why such blocks were present. A detailed analysis of the situation often indicated that the cause of the blocks is that explained by figures such as 6 and 7 below in the article.

Jan 1, 2018

By Adrian Moore, Dominic Hooton, Alan Richards

Significant factors affecting airblast overpressure (AOP) emissions include charge mass per delay, distance from the blast site, burden, stemming height, and delay timing, topographic shielding, and meteorology. The effect of charge mass on the frequency of the airblast produced, and the delay timing required to control the level of airblast overpressure is explained by two case history examples which were not affected by topographical shielding and meteorology. One is a cast blast with a charge mass per hole of 1000 kg (2200 lb), and the other is a quarry blast with a charge mass per hole of 64 kg (141 lb), These examples show that the delay interval necessary to prevent an increase in AOP levels must be increased with an increase in charge mass per hole. The effect of a ‘soft-start’ technique where a reduction in AOP levels is achieved by decking only the initial front-row holes is also illustrated.

Jan 21, 2025

By Kyle Apple

The following is a case study of how LuckStone Corporation improved their blast monitoring and documentation program. A number of resources already at their disposal have been utilized to improve the body of data collected from each blast. The tools being used include GPS, aerial photos, and a user-friendly push button format excel spreadsheet. The data collected include product by product records of materials used, distances to all concerned neighbors, seismograph data, etc: The spreadsheet has been designed to perform an ongoing analysis of blasting trends. The program has been carried out at a corporate level and is in use by blasters at each location. This paper addresses the advantages and drawbacks of this program. It also addresses the ways in which the various tools were integrated, Discussed as well is the need for simplicity when bringing “new” technology to the field and the steps taken in familiarizing the end user to changes.

Jan 1, 2001

By Scott King, Norm Patterson, Ruilin Yang

The multiple blasthole fragmentation (MBF) model developed by Orica models the contributions from multiple blastholes to fragmentation at any given point in the rock and simulates a production blast with the actual geometry of the blasted overburden and free faces, explosive loading, multiple decking, and delay timing of each explosive charge. The model has been successfully applied to several open pit mines and quarries around the world, including Canada and the United States. The peak particle velocity (PPV) induced in the rock from the explosive detonation is used in the MBF model as the key parameter relating to the size distribution of the rock fragmentation. Relating the PPV to the rock fragmentation is based on earlier work relating the particle velocity to the dynamic strain in rock. A recent publication further revealed that the PPV is related to the maximum relative displacement that induces three dimensional strain at a point in the rock. The model can explicitly model most of the blast design parameters including explosive properties.

Jan 1, 2018

By María Rocha, Benjamín Cebrián, Roberto Laredo

"Ring blasting designs have to achieve different goals in order to become efficient whether is done in up hole or downhole fashion. Ore recovery/dilution control, fragmentation and drift integrity all have to be taken into account when selecting parameters such as burden, spacing, linear explosive density and stemming. Blast energy simulation allows identifying contours of rock breakage and fragmentation, thuschoosing a combination of spacing at the end of holes and appropriate burden. Also, simulations are keyto concentrate energy levels on the mid part of the ring while making sure there is not too high of energy concentration around the drift, which integrity is needed for a safe ore mucking."

Jan 1, 2017

By Reinhold Daykin, Piers Wendlandt, Nathan Rouse

Drilling and blasting are key components of every hard-rock (i.e., metal/nonmetal/coal) mining operation. Well-executed and maintained drilling and blasting can have a major positive impact on the overall success of such operations. This case study presents the implementation of a new drill and blast engineer position and systematic improvement of the drill and blast operations at a surface metal mine.

Feb 1, 2020

By Tyler Acorn, Paul Worsey, Nathan Rouse

The effect of the hole diameter on vibration attenuation has not been incorporated in most vibration models in the blasting industry. In current vibration models, the charge weight and the distance from the blast are the two primary variables that are addressed. Charge weight is a function of explosive density, charge length, and charge diameter. This geometry-weight can complicate the isolation of the charge diameter variable.

Jan 1, 2013

By Cesar Guerra, Alejandro Rojas, Dr. Jhon Silva, Luis Velasquez

The ANN method is applied to predict the P_80 size in one open pit gold mine in Peru. The ANN was implemented in Matlab programming language, and the results from the ANN are compared with data obtained using photo-fragmentation analysis software.

Feb 1, 2020

By Richard Turnbull, James Purssey

"The Northconnex Project is a twin nine kilometre tunnel in Sydney, Australia, linking the M1 PacificMotorway at Wahroonga to the Hills M2 Motorway at West Pennant Hills. Access to the tunnels will befrom portals at either end and from three vertical shafts spaced along the length of the motorway. These shafts will provide access for equipment, plant and personnel, removal of spoil during construction,ventilation, and emergency egress points during tunnel operation. The three shafts have a 12 m x 16 m (39 ft – 53 ft) cross sectional area and depths ranging from 45 m to 91 m (148 ft – 299 ft). The vibration limit for the shaft blasting was set at 10 mm/s ppv, with residential properties as close as 31 m (102 ft) and the existing M1 motorway 80 m (262 ft) away. The traffic volume for the M1 is 80,000 vehicles per day and Northconnex will provide an additional 100,000 vehicle capacity. "

Jan 1, 2017

By Jennifer Williams, Donald J. Berger

Originally built between 1913 and 1916, the Ashton Dam & Hydroelectric Facility has experienced various seepage and piping incidents since completion. Ashton Dam is located within 15 miles (24 km) of the historical Teton Dam failure site and about 2.3 miles (3.7 km) west of Ashton, Idaho. Numerous repairs conducted over the years ranged from filling sinkholes on the crest of the dam to placement of rockfill on the upstream slope to improve seismic stability. In addition, the existing low level outlet works was grouted full and abandoned in 1991 due to significant vibrations induced on the dam during its operation.

Jan 1, 2014

By H. S. Venkatesh, G. Gopinath, R. Balachander, G. C. Naveen

Punatsangchu Hydroelectric Project Authority is constructing 1020 MW underground hydroelectric project in Bhutan. The project envisages construction of concrete dam, Desilting Chamber, Head Race Tunnel, Power House Complex and Tail Race Tunnel. Tunneling is one of the major activity in any underground projects as they are driven for multiple activities. By and large the tunnels are a major part of connecting networks from surface to caverns/underground working sites. Many tunnels in hydropower project are part of water conducting systems and one such important tunnel is the Tail Race Tunnel in this project and had to be excavated in thinly foliated rockmass conditions by D&B method.

Feb 1, 2020

By Robert Lee, Pertti Paavola

Automated vibration monitoring and web-based data distribution has proven itself on the largest single construction project ever undertaken in Finland. The excavation for the Kamppi Center Project in the center of Helsinki was completed in November of 2003 and involved the removal of over 200,000 m3 (260,000 yd3) of rock and over 1,700 individual blasts. A system was installed, incorporating 37 discrete monitoring points located throughout an underlying metro station, and other surrounding underground and surface facilities. After every blast, vibration data was automatically transferred from the monitoring network to a server database. Stakeholders were able to access and review vibration reports on a password-protected website within 90 seconds of each blast. This allowed engineers to verify that recorded levels were in compliance with established limits, before proceeding with subsequent blasts. The data was also imported into a semi-automated Scaled Distance tool for analysis using linear regression techniques. This was used to determine, and adjust for trends in blast-induced vibration.Copyright

Jan 1, 2004

By Tyler Rockley, J. P. Remi Proulx, Ruilin Yang

A highwall blast vibration project was carried out to quantify the level of blast vibrations produced from a trim blast in soft rock and a combined production and trim blast in hard rock. Combining production and trim blasts could be performed without exceeding the mine’s vibration limits.

Feb 1, 2020

By Gordon K. Jorgeonson

Much of the modelling of blasting operations has been devoted to simulating blasts in open pit mines and quarries . This has been the most obvious application and has been reported in many papers and discussions in the past.

Jan 1, 1990

By Robert Hopler

The 1800’s were a time of tremendous advancements in science and experimentation, and earthquakes were a subject of great interest. The meetings of the British Association for the Advancement of Science in 1853 and 1854 are good examples of this. The proceedings of the Association for the 1854 meeting includes a table entitled “Catalogue of Recorded Earthquakes from 1784 to 1850” which takes up 326 pages, and lists available information on approximately 3000 earthquakes. The 1853 proceedings have a similar table for earthquakes recorded from 1606 B.C. to 1783. In the 1854 volume there is a “Report of the Committee on Earthquakes,” which provides us with a view of the general state of the science. Excerpts from that report follow:

Jan 1, 2006

By Adrian Moore, Alan Richards

"It has been common practice to set blast vibration limits for structures using an “observational”approach whereby limits are set at a level based on observations of damage, or the lack ofdamage, combined with a tendency to further reduce the permitted level due to uncertainty. Suchan observational approach was used in the USBM RI 8507 to produce the frequency dependent‘Safe Levels of Blasting Vibration for Houses’ which has become a universal Standard for overthirty years."

Jan 1, 2013

By K. Taylor

In surface coal mining, the performance of a shovel through blasted muck is one of the key performance indicators of the blast. Historically, performance has been measured qualitatively based on operator feedback or visuals of the muckpile. More complete shovel data, such as loading times and GPS location, is available from most fleet dispatch systems that are already in place at most truck and shovel operations. With some database and analysis skill, the drill and blast team can take advantage of this data to make targeted improvements to drill and blast designs. An area typically known to cause trouble for shovel operators at this operation are blast boundaries. Blast patterns with and without design changes along the boundaries were studied in this case study. The instantaneous loading times for each shovel pass were analyzed for 75 blasts across two subsequent benches with similar firing direction and shovel paths. The benches were split into three categories: Main body of pattern, boundary with design change, and boundary with no design change. The loading times from the main body of the patterns and where the design change was utilized in the boundary had similar prevalence of good loading times. However, boundary areas without the deign change had approximately 2% more prevalence of poor loading times compared to the main boundary of the pattern. Improving the dig rates through the boundaries up to the average loading time would result in approximately 280 hours taken off the total loading time for one bench. By quantifying the shovel’s performance by GPS location, the drill and blast team can decide how much of a design change is needed, can target precisely only the areas that require it and measure the impact of any changes made

Jan 1, 2024

By Josh Calnan, Zach Agioutantis, Daykin Schnell

Damage complaints are a common occurrence related to blasting activities, specifically when blasting operations occur near residential areas. These complaints are often associated with ground vibrations from blasting. It is important for blasters and engineers to understand the potential for ground vibrations to damage residential structures to properly design blasts and appropriately address any damage complaints that arise. A review of the most recent studies of blast vibration damage thresholds for residential structures is conducted to provide a baseline understanding of blast damage potential and mechanisms. Gaps in research and understanding blast vibration damage potential are identified. Research in further understanding damage potential is presented and focuses on studying the impact of high-range ground vibrations generated from full-scale, nearfield ground vibrations from blasting on a residential structure. Specific impacts of the high-range ground vibrations reviewed as part of this research include damage to the block wall basement, global strain, rotational forces, crack generation, and crack extension in a residential structure. Planning and methodology for intentional full-scale, nearfield blasting at a limestone quarry within close proximity to a residential structure owned by the quarry are presented. Conclusions discuss the objectives and optimized layout of the ongoing data collection for the proposed research and analysis. Future potential work related to further understanding blast damage mechanisms and thresholds are also discussed.

Jan 26, 2026