Search Documents

By D. G. F. Hedley, D. F. Coates, K. Barron

INTRODUCTION Preceding papers presented in this symposium have considered the influence of various parameters, such as geologic structure, groundwater, etc., on the stability of rock slopes and have given some analyses and guide lines for slope design. To carry out such analyses it is necessary to put numbers to these parameters; where possible, this is best done on the basis of in- situ observation and measurement. Since none of the design analyses can be considered exact and since conditions vary during excavation, it is also desirable to monitor the behaviour of the slopes as the excavation proceeds. In this manner a feedback of information on the actual excavation conditions can allow a continuous reassessment of the design parameters to be made and can give early warning of incipient failures. The purpose of instrumenting rock slopes is thus to provide information which fits into one of two categories: (a) To give basic data to assist on-site assessment and design of the rock excavation. (b) To provide data for the control and assessment of safety during excavation. The purpose of this paper is to review briefly some of the instruments and measuring techniques available for gathering this data and to indicate where such data may prove useful. This is not a comprehensive review of all available instrumentation but, rather, is a survey of some of the instruments and techniques with which the authors have had some experience and which have proven useful. STRUCTURAL ASSESSMENT Whilst most structural assessment of a site is done on the basis of geologic mapping and core examination, there exists some instrumentation which can, in particular circumstances, assist in this assessment. Seismic instruments can be used to determine the geometry of formations and to give an indication of the relative competency of rocks. These instruments operate using seismic reflection or refraction techniques and, although mainly confined to shallow sub-surface exploration, can be useful in distinguishing between soil/ bedrock contacts and, in some cases, the extent of weathered surface rock.

Jan 1, 1971

By J. Handin, S. J. Bauer, M. Friedman

Deformation mechanisms in room-dry and water-saturated specimens of Charcoal Granodiorite, shortened at 10-4s-1, at effective pressures (Pe) to 100 MPa and temperatures to partial melting (?1050°C) are documented with a view toward providing criteria to recognize and characterize the deformation for geological and engineering applications. Above 800°C strength decreases dramatically at effective pressures ? 50 MPa and water-weakening reduces strength an additional 30 to 40% at Pe = 100 MPa. Strains at failure are only 0.1 to 2.2 percent with macroscopic ductility (within this range) increasing as the effective pressures are increased and in wet versus dry tests. Shattering (multiple faulting) gives way to faulting along a single zone to failure without macroscopic faulting as ductility increases. Microscopically, cataclasis (extension microfracturing and thermal cracking with rigid-body motions) predominates at all conditions. Dislocation gliding contributes little to the strain. Precursive extension microfractures coalesce to produce the throughgoing faults with gouge zones exhibiting possible Riedel shears. Incipient melting, particularly in wet tests, produces a distinctive texture along feldspar grain boundaries that suggests a grain-boundary-softening effect contributes to the weakening. In addition, it is demonstrated that the presence of water does not lead to more microfractures, but to a reduction in the stresses required to initiate and propagate them.

Jan 1, 1982

Manganese nodules are essentially a surficial resource-there are four times as many nodules on the surface of the deep ocean floor as in the next 3 ft of underlying sediment. Target mine sites in the North Pacific occur in water 12,000 to 18,000 ft deep. The mining technique is comprised of four major factors: the mining device, lifting method, surface vessel, and ore transport. Certain deep-ocean mining proposals are revolutionary in character. Current research has tended to construct simple but flexible devices to work at the great depths and corrosive environments of the deep-ocean floor

Jan 4, 1975

By J. W. Spretnak, R. Speiser, A. M. Adair

THERE are sufficient arguments and evidence to indicate that boron should be adsorbed to existing austenite grain boundaries during the austen-itizing treatment. Accordingly, it is possible that boron contributes to the hardenability of heat-treatable steels by the reduction of the interf acial energy of austenite grain boundaries, at which sites are nucleated heterogeneously the decomposition products of austenite. Such a reduction in interfacial energy would reduce the total energy that can be borrowed in these heterogeneous nudeation processes and thus retard the initiation of transformation. This investigation was undertaken in an attempt to determine the effect of boron on this interfacial

Jan 1, 1956

By C. O. Brawner

Introduction The procedures used to design slopes in rock have only been developed over the past 10 years. Therefore, continued review and assessment of field experience by the publication of case studies is necessary to determine the accuracy of the theory and the application of the design techniques being used. Where failures have occurred, mine management should insist that the slides be 'back analyzed' to determine the shear strength parameters at failure. These values should be used for any pit design as they reflect site conditions more accurately than any other procedure. The previous papers have dealt with the basic concepts and factors that influence stability. To illustrate the application of these concepts in the study of practical stability problems, six ease studies have been selected for review. The examples include failure of tailings dams due to an earthquake, failure and redesign of a slope in overburden, review of failures of rock slopes, calculation of the amount of seepage into a pit and influence of the groundwater on stability, and the design of slopes for a proposed 2,500 ft. deep open pit mine. All but the first example are drawn from the authors personal experience. EXAMPLE 1 Failure of Tailings Dams Due to an Earthquake On March 28. 1965 a serious earthquake occurred in Chile with the epicenter located near the town of La Liqua, about 80 miles north of Santiago. The earthquake had a rating of 7 to 7.25 on the Richter scale. A record of the acceleration was taken at Santiago where a maximum horizontal acceleration of 0.18 g. was recorded. Many small mines are located in this region. Each of the mines provided impoundment storage for tailings with one to three dykes. As a result of the earthquake, most of the dams failed. The most serious failure involved two dams at El Cobre where more than 2,700,000 cu. yd. of tailings flowed into the valley, travelled over 7 miles in a few minutes, destroyed part of the town of El Cobre and killed more than 200 people. The Chilean government commissioned an investigation into the failures. A summary of the findings was published by Dobry and Alvare7 in 1967 (1). The location of the earthquake and the tailings dams which were investigated is shown

Jan 1, 1971

By M. E. Wadsworth, A. S. Peck

Infrared spectra disclose that oleic acid will not adsorb on the surface of pure beryl unless the mineral is first activated with HF. The adsorption of oleic acid on HF activated beryl is attributed to the hydrogen bonding of oleic acid monomers to F-surface bridging sites. These sites are formed as a result of the reaction of HF with chemisorbed water or surface hydroxyl. Characteristic infrared spectra of physically adsorbed oleic acid are correlated with flotation at different pH at temperatures of 25°C and 75°C for colloidal and -60-mesh particles. The usual mode of occurrence of the beryllium mineral beryl, Be3A12Si6O18, is in granite pegmatites as pale green, white, or yellow crystals. A dark green gem variety, emerald, may be found in the wall rock of pegmatite veins or in mica schist. The most important beryl deposits in the United States are in the Black Hills District of South Dakota, and several mountain ranges of central and west-central Utah contain potential commercial sources of this mineral. Several papers have been published concerning the flotation of beryl with different conditioning reagents. Kennedy and O'Meara1 reported on the essential use of HF in the flotation of beryl from different ores. The use of calcium hypochlorite to separate HF activated beryl from feldspar after flotation with an amine collector was made by Runke.2 A report on the activation of beryl with different cations using sodium oleate collector was presented by Viswa-nathan and co-workers.3 Flotation of beryl with sulfonate collector and different activating salts was employed by Fuerstenau and Bhappu.4 The role of the surface charge or zeta potential in the flotation of beryl with different collectors and salts was also extensively investigated.5"7 Previous infrared investigations by the authors8 disclosed that the orthosilicate beryllium mineral, phenacite, reacts with oleic acid to form a chemisorbed oleate monolayer on the mineral surface. Thus, chemisorption is the effective mode of adsorption in the phenacite-oleate acid flotation system. In contrast, neither chemisorption or physical adsorption of oleic acid occur on the surface of pure beryl as evidenced in this study. Efforts were subsequently made to determine the mechanism of activation and collector adsorption for HF pretreated beryl. EXPERIMENTAL PROCEDURES Large, white, terminated crystals of beryl were obtained from Madagascar through Ward's Co., Monterey, Calif. The crystals were broken into -60-mesh fragments in a porcelain mortar. Part of this prepared material was ground to a powder with a Fisher Grinder using an agate mortar and pestle. The powder was transferred to a graduated cylinder and mixed with 500 ml of distilled water. After 5 min, the colloidal suspension was separated from the settled particles by decantation and used as a stock for infrared test determinations. Adsorption tests were performed by first transferring 20 ml of colloidal suspension to 50 ml glass centrifuge tubes. The solids were then centrifuged out and the liquid was discarded. Then, the solids were pretreated with one molar HC1 or one molar HF. After 15 min, the solids were again centrifuged out. The mineral solids were washed free of residual acid by repeated centrifuging and water washing operations. Then, 20 ml of distilled water was added to the solids, and the resultant suspension was used for test purposes. In the preparation of mineral for flotation tests, 1.5 g of -60-mesh beryl was deslimed by removing the colloidal fraction by three successive water washes and decantations. Then, the coarse particles were pretreated with either one molar HCl or one molar HF for 15 min. The mineral was next washed free of acid with distilled water, and 20 ml of distilled water was added to the beryl prior to collector conditioning. The conditioning of mineral with collector was performed in 50 ml centrifuge tubes to which either NaOH or HC1 was added for pH modification. One drop (6.0 mg) of U.S.P. reagent grade oleic acid or 2 ml of 0.01 molar sodium oleate was added to the pulp and stirred at about 1500 rpm for 3 min at a

Jan 1, 1968

By P. R. Sperry, P. A. Beck, J. Towers

Dahl and Pawlek1 found that electrolytic copper develops extremely coarse grains at 1000°C after about 90 pct reduction by rolling. This coarsening occurs only under conditions of penultimate grain size, deformation, and alloying which lead to the "cube" recrystallization texture.l,2,3,5 The peculiar angular shapes and straight grain boundaries of the coarse grains were noted by several investigator.1,4,5 On the other hand, coarsening in Fe-containing aluminum or in AI-Mn alloys8 does not depend on a "cube" (or any well developed) recrystallization texture. It is true that increasing deformation by rolling, and, therefore, an increasingly well developed re-crystallization texture, are associated with decreasing incubation periods of coarsening.6-7-8 Nevertheless, coarsening readily develops in aluminum even after only 30 pct reduction by rolling, where the recrystallization texture is very weak.6,8 Also, coarsening was observed by Jeffries9 many years ago in sintered thoriated tungsten, which presumably has no preferred orientation. In all these cases coarsening is associated with grain growth inhibition by a dispersed second phase.8,9 The annealing temperature has to be suficiently high to overcome the inhibition at a few locations. But if it is too high, growth starts at many points, and the resulting grain size becomes much smaller.9 Normally, the coarse grains are more or less equiaxed, and the boundaries have a typical ragged appearance.6.8 Cook and Macquarie4 demonstrated that, in addition to the texture-dependent coarsening previously found at 1000°C,l electrolytic tough pitch copper may also coarsen at 800°C after 50 pct reduction by cross rolling. The coarse grains formed under such conditions have rounded shapes and ragged boundaries, like those in aluminum. When the annealing temperature is higher, the tendency for their formation decreases. All these observations suggest that the coarsening at 800°C is associated with inhibition by a second phase. Actually, coarsening at 800°C after 50 pct reduction by cross rolling was observed only in tough pitch copper,4 which contains Cu2O particles. On the other hand, the texture-dependent 1000°C coarsening occurs in both tough pitch and oxygen-free copper;4 it does not appear to depend on the presence of a dispersed second phase. However, the interpretation of the 800°C coarsening in Cu after 50 pct rolling as an inhibition-dependent process, similar to the coarsening in A1-Mn alloys, is somewhat weakened by the fact that this coarsening was reported4 to occur only after cross rolling, and not after straight rolling. It was, therefore, decided to re-examine this question. A 1 in. diam electrolytic tough pitch copper rod, No. 2 hard drawn, was annealed for 20 min at 700°C, rolled to 0.5 in., annealed 10 min at 700°C, and straight rolled to 0.064 in. It was then given a penultimate anneal of 20 min at 500°C and it was cut into four sections, which were given final reductions by straight rolling as follows: A 30 pct reduction of area B 50 pct reduction of area C 70 pct reduction of area D 90 pct reduction of area Specimens cut from the four sections were finally annealed at 800°C in an oxidizing atmosphere. Strip A remained fine grained up to 10 hr, but the specimen annealed 12 hr consisted of only 2 large grains. Strip B had a few scattered large (1/2 to 3/4 mm) grains after 1 min, although the balance of the specimen consisted of fine grains of about 0.02 mm. After 5 min there were several 10 to 15 mm grains present, and after 1 hr strip B was completely coarsened. The coarse grains had the same characteristics (see Fig 1) as those obtained by Cook and Macquarie at 800°C after cross rolling. Strip C had several grains of 0.05 to 1 mm after 1 min, but it was still largely fine grained after 12 hr. After 48 hr it consisted entirely of grains of about 0.5 to 4 mm, with an extraordinarily large number of twin bands. Strip D remained com- pletely fine grained after 4 hr at 800°C. These results indicate that, in the deformation range of 30 to 70 pct reduction, the incubation period for coarsening as well as the rate of growth and the final size of the coarse grains decreases with increasing deformation. Similar

Jan 1, 1950

By H. LeRoy Scharon

The electrical resistivity method was utilized at 245 road cuts and structure sites over the 166 miles of the Philadelphia and Western Extensions of the Pennsylvania Turnpike System. Varying geologic structures and rock types afforded an excellent academic study of the method as well as a practical application to modern highway engineering.

Jan 4, 1951

By Gerald Edmunds

CASTINGS of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, some-times nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is devel-oped to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and there-fore the position of the grains is more com-plex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicat-ing that thermal contact was better there than in neighboring areas.

Jan 1, 1940

Discussion of the paper of EDGAR L. NEWHOUSE, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin: No. 92, August, 1914, pp. 1801 to. 1806. G. C. RIDDELL, East Helena, Mont.-As nearly as I can recall at the present moment, there are only four or five large plants on the continent where the lead on charge is carried in the neighborhood of 40 per cent. These are at Herculaneum, Collinsville, and Federal, Ill.; Trail, B.. C.; and East Helena, Mont. Our object at the latter point is to smelt a maximum amount of Coeur d'Alêne lead sulphides in as compact and self-fluxing a charge as possible, and to this end we are now smelting a mixture that at times carries up to 42 per cent. lead. The monotony of producing the 7,000 tons of bullion shipped each month to. the Omaha and Chicago refineries is relieved somewhat by the fact that the 15,000 tons monthly of Coeur d'Alêne ores that are com-ing to us carry enough zinc to provide the one-half slag used with from 6.5 to 7.5 per cent. zinc clay after day. During the month of March, 1914, three lead furnaces in continous operation, each 136 in. long, averaged 249 tons per furnace clay, exclusive of coke and slag shells, which is smelting at the rate of 5.5 tons per square foot of tuyère area. The

Jan 11, 1914

By J. W. Littleford

The Roan Antelope Copper Mines Ltd. are situated in the north central part of Northern Rhodesia, at an altitude of 4000 ft. and 13" south of the Equator. The town site (Luanshya) is well situated and enjoys among other things a really temperate climate for 10 months of the year. The two spring and summer months, October and November, while hot and humid, do not bring any great discomforts as compared with many other mining camps. Strictly modern brick homes, with electric lights, purified water, telephone and water-borne sewage, add to the comfort of the employees. A rainfall of approximately 60 in. per year furnishes ample water for both industrial and domestic purposes. The rainy season generally begins in October and lasts through until March. As much as 3 to 4 in. is recorded in 24 hr., but this offers no difficulties because the runoff is very rapid. The property is connected by a 24-mile branch line from Ndola with the main line of the Beira-Mashonaland and Rhodesia Railways Ltd. Practically all supplies from overseas are transported over this line from Beira, 1743 miles distant on the east coast in Portuguese East Africa. The mine output also leaves Africa from this port. Passenger service is principally via Cape Town or Durban, a distance of about 2100 miles to either port. The Imperial Airways maintain a service from Cape Town to Croydon, taking 9 days for the trip. Connections can be made with this service at Broken Hill, 150 miles south of Luanshya, by either rail or automobile. Thus, after several days of travel through virgin bush, a visitor arrives at a typically modern town site in the heart of Africa. Every development in mining, milling and smelting practice is used to advantage. Plan of Mill The practice in the three principal phases of the production of copper from the ores of this company have been published from time to time. Milling practice, however, is continually changing and what may be

Jan 1, 1935

By Malcolm J. McPherson, Michael Hood

Sunnyside Mines, owned and operated by the Kaiser Steel Corporation, are situated near the city of Price, Utah. The complex comprises three adjacent mines, named simply Nos. 1, 2 and 3, all connected underground. Two seams, the upper and lower Sunnyside have been worked. These dip at about 10 percent to the north-east. The surface cover is variable due to the mountainous nature of the topography. The Sunnyside upper seam varies from 5 1/2 ft (1.7m) to 9 ft (2.7m) In thickness whilst the lower seam remains at about 6ft (1.8m). The separation between the two seams has ranged from 7 to 45 ft over the mined area (2 to 14m). Longwall mining has been practiced at Sunnyside for over 20 years due to difficulties of roof control encountered when using the roan and pillar system. Number 3 mine is bounded on the north and south sides by mines Number 1 and 2 respectively. Whilst current production is concentrated into Number 1 mine, much of the future of the complex lies in the further development of deeper reserves in Number 3 mine. Workings in this latter mine were curtailed in 1978 due to difficulties in ventilation. Present developments are ventilated partially from the neighboring Number 2 mine where no workings are in progress. The layout of Number 3 mine is illustrated on the schematic Figure 1. Trunk airways extend down dip from the surface at No. 2 Canyon and the Water Canyon for a distance of some 9,600 ft. (2930m). The area between the two sets of trunk airways has been worked extensively in both seams as have the corresponding reserves on either side in the connected adjacent mines. At the present time exhausting fans are sited at the top of a shallow shaft in No. 2 Canyon and an 8 ft (2.4m) diameter shaft sunk to a depth of 1013 ft (310m) closer to the current developments (Figure 1). The current airflow system, even with an additional 116,000 cfm (55m3/s) entering from No. 2 Mine, is adequate only for the development work now in progress but will be unable to support new longwall faces further downdip. The basic ventilation problem of this mine may be stated quite simply. In a situation where all intake and return airways pass through extensive old workings, a ventilation system design was required that would be effective, efficient and economic for the foreseeable future of the mine. ORGANIZATION OF THE PLANNING PROCEDURE The procedure followed during the study is illustrated on Figure 2. Initial ventilation surveys established the current state of the airflow system and provided the necessary data for setting up a Basic Network File in a computer store. The data in this file was a mathematical model of the ventilation system of the mine. The basic network was analysed by a ventilation network analysis program in order to correlate the measured and computed airflows and to establish the basic network as a true representation of the mine as it stood at the time of the surveys. The network model could then be extended to simulate the future development of the mine and alternative ventilation designs investigated. The remaining sections of the paper outline the work involved in each of these main phases of the planning procedure. VENTILATION SURVEYS Conduct of Surveys Two types of measurements were conducted simultaneously throughout the air-carrying routes of the mine: (i) Airflow measurements were made by anemometer traverse or smoke tube at 221 selected stations. Anemometer traverses were repeated at each station until at least three gave results to within 5 per cent. (ii) Pressure drop measurements were made across ventilation doors, regulators and, wherever possible, across stoppings. Additionally, frictional pressure drops were measured along airways where such pressure drops were significant (above 0.01 inches of water gauge or 2.5 Pa over a 100m distance). The trailing hose method was used to determine these frictional pressure drops. This involved laying out 100m of abrasive resistant plastic tubing (3 mm internal diameter) with a 4 ft. pitot-static tube facing into the airflow at either end and a low range pressure gauge connected into the line. The trailing hose method was preferred to the alternative barometer technique for this study because of (a) the relative ease of access between measuring points and (b) the greater accuracy within individual airways. The anemometers used were Davis Biram Type A/2-3" (30 to 5,000 ft/min) and Airflow Developments AM-5000 digital (50 to 5,000 ft/min). The pressure gauges employed were Dwyer magnehelic instruments. These were preferred to liquid in glass manometers because of their portability and dependability under adverse mining conditions. A checklist of the equipment used in the survey is given in Appendix 1. The instruments were calibrated before and after the surveys in the mine ventilation laboratory at the University of California, Berkeley. The survey occupied two teams, each of three men, for ten working days. The work consisted

Jan 1, 1982

By Owen F. Jensen

CONSTRUCTION of a ground-water supply includes many operations, which do not end with completion of facilities. Evaluations must be made of the quality of water in various areas and the history of production. Following an analysis of geologic, hydrologic, and chemical data there must be an exploratory drilling program and a study of resulting information. When the well is completed a continuous survey of operating records and basic data is necessary, since designs for future wells are varied as more data becomes available for those already completed. As the following discussion must be limited to a single undertaking, the customary procedure will be outlined for development and construction of a ground-water supply in which more than three wells are involved. Parts of this procedure are applicable for all ground-water supplies. Three possible sites were selected for construction of a paper mill. The problem was that the industry daily required approximately 15 million gallons of water of the best quality available; however, if water of the best quality were not available in the desired amount, water of a poorer quality could be used up to half the required amount, about 7 million gallons. In the preliminary survey approximately 1500 to 2000 square miles were covered for each site. Collected data consisted of several hundred electric logs of oil and gas wells; reports by the U. S. Geological Survey on ground-water resources of localities in and near the area; unpublished records of several hundred water wells including chemical analyses of the water produced and drillers' logs of the wells; records of periodic water-level measurements made in observation wells by the USGS; topographic maps drawn up by USGS and by army engineers; and highway and county road maps. A preliminary report based on study and evaluation of these data was presented to the client, recommending the site with the most favorable and economical ground-water conditions. The study indicated that water of the quality and quantity desired could be developed. In this particular area there were indications that the aquifer could be separated into two zones con- taining water of different chemical character. This chemical character varied somewhat with area, but principally with depth, a factor which later proved an economic advantage in design of the well field. After studying the preliminary report, the client weighed other economic factors as well as ground-water advantages and selected a plant site. Authority was given to proceed with detailed study of the chosen area. Evaluation of preliminary data concerning the area indicated that it should be supplemented with additional information derived from actual exploratory drilling and testing. A flexible plan of exploratory drilling was devised so that data obtained as each test hole was drilled could be correlated with existing data and additional test holes could be located and drilled accordingly. Specific data to be obtained from each test hole were: samples of all formations penetrated; the driller's descriptive log of formations; electric logging surveys; one or more samples of water from selected water-bearing formations; temperature; and water levels and their recovery after periods of production. The area studied in such detail was approximately 400 square miles. Choice of location for the original test holes was based on the preliminary study. The pattern for these test holes was designed to require a minimum number of holes and to allow for interpolation of data between two, three, and four holes. Geologic, hydrologic, and chemical data gathered after completion of the first four test holes showed that the north section was the most desirable in the area, which was then reduced from the original 400 square miles to about 150 square miles for more detailed and intensive study. On the basis of findings from the current test a tentative well field was laid out and a drilling program devised. One test hole was located on the actual plant site and later developed into a small pilot production well equipped with a deep well turbine pump. Water from this well was used for general construction requirements. Another test hole drilled near the pilot production well and adjacent to the proposed route of the well-collection system was used during the pumping test of the pilot production well to determine the degree of interference. From the data thus obtained, calculations were made to determine the coefficients of transmissibility and storage. Three additional holes

Jan 1, 1955

By Y. A. Topkaya

The placer gold occurrences at Sart Çayl, Manisa, Turkey, the legendary River Pactolus of King Croessus, were evaluated in this study to determine if this deposit contains sufficient recoverable value to justify development and exploitation. The gold occurs both in the upper Neogene conglomerates and the alluvium derived from these conglomerates. The total reserve in the whole region is estimated to be 500 million cubic metres. Samples were taken of the upper conglomerate and in the alluvium in an attempt to determine the amount and the physical nature of the gold. The gold in samples was recovered by screening out barren oversize followed by washing the sand and gravel through riffled sluices. The resulting sluice concentrate was later panned and amalgamated at site. Laboratory cyanidation testing of some samples for control purposes was also done. The average calculated free gold was found to be about 90-100mg/m3 and the size of gold flakes found was quite small. The field as well as laboratory testing of the samples of Sart Çay1 indicated that the potential reserves in this region could only be developed as a sand and gravel operation and the gold could be recovered together with the heavy minerals as a byproduct.

Jan 1, 1984

By E. Amott

A test is described in which the wellubility of porous rock is measured as a function of the displacement properties of the rock-water-oil system. Four displacemet operations are carried out: (I) sponlaneous displaceti?ent of water by oil, (2) forced displacement of water by oil oil in the same system using a centrifuging procetllrre, (3) spontaneous displacement of oil by water. and (4) forced displacment of oil by water. Ratios of the spontaneous displacement volumes to the total displucenlent volumes are used as wettability indicates. Cores having clean mineral surfaces (strongly preferentially water-wet) show displacement-by-waler ratios approaching 1.00 and displacement-by-oil ratios of zero. Cores which ([re. strongly preferentinlly oil-wet give the reverse resu1ts. Neutral wellability cores show zero values for both ratios Fresh cores from different oil reservoirs have shown wettabiltties in tlris te.st covering rrlti~ost 111e conlplrtt, range of thr: te.st. Notvever, nlo.s/ of tlle fresh California cores tested were slightly prcfere111icrlly wclter-\vet. The chrrnge.~ in coro u ('liabilities, as indicated hy this te.st, r~.sril/ing from various CO~P hanrlling procedures tt,ere oh.served. In sonie ca.sc,s /Ire ~,cttahilitio.c. of fresh cores were changell by drxi:~g or 11y e.x/rclct ing with iolcreiii~ or. dioxunc~; in o/h~r cases they were 1101 changed. Co~ltrrc/ of cort,.s ~.ith filtrc~t~c. from water-base rlrilling rilrrrls crlrc.sed littlc change in we/ /ahility ivhile contnct with filtrates frorii oil-hus~ ri1rlcl.s tlecrrascrl the prefcrerlcc, of the, cores for )I.NI Usitig thi,s test to ri.crl~lute n~r~ttubili~y, N .vt~ldy was iilarle of /lie correlmtio~i of wettability with wa/erfloocl nil recovery for orttcrop Ohio sand.stone and for Al~ln-tlunl. Resul/.v indicate thml no single correlatioti between these factors applies to different porous rock syste~n. It is thought that diflerences in pore gen~netry resrrlt in diflrrerrce.~ in this correlurio~z. INTRODUCTTON Most investigators who have reported on the wettahility of porous rock have described such rock as prcferentially water-wet or preferentially oil-wet. In some cases a third classification, neutral wettability. has been used. The efficiency of water floods in each of these wettability groups has been described in numerous publications. Several methods for characterizing porous rock wet tability more precisely have been reported,' " but it appears that because of one weakness or another. none of these has been generally accepted. Early in our studies in this field, it was found that the displacement efficiency of oil by water in a particular porous rock having a strong preference for water was quite different from that in a similar rock having only a moderate preference for water. Thus, there appeared to be a need for a practical, reasonably precise wet tability test. one which could classify porous rocks into 10 to 20 different groups rather than the two or three broad groups listed above. The test developed to meet this need is described in this paper. Also, changes in wettability, as indicated hy this test, resulting from various core handling procedures are discussed. Finally, data showing the corrclation of wettability with waterflood oil recovery for two different types of cores are presented and discussed. Some confusion has resulted from the failure of certain writers to define clearly some of the wettability terms they have used. Accordingly, the following commcnts concerning definitions are offered. The wc t ta-hility of a solid surface is the relative preference of that surface to be covered by one of the fluids under consideration. It is felt that this is the generally accepted definition. The fluids being considered must bc specified (or understood) before the term wettability has any significance. In the work reported here these fluids are water (3 per cent brine) and oil (kerosene). The term preferential wettability is sometimes used, but we think that the word preferential is redundant here and should not be used. Tn line with the definitions of Jennings', a preferentially oil-wet solid surface is regarded as a surface which will show an oil advancing contact angle less than 90" (measured through the oil) in the water-oil-solid system. Oil will spontaneously displace water, if both are at the same pressure, from such a surface. A preferentially water-wet surface is analogous. This is consistent with the wettability definition above. As Jennings has said, frequently the term oil-wet is used to mean the same thing as preferentially oil-wet. However, oil-wet also has been used occasionally referring to an oil-covered surface when the availability of water was limited. To avoid confusion from this source, we do not use the terms oil-wet and water-wet. DESCRIPTION OF WETTABTLITY TEST The following points were considered desirable in a wettability test for our purpose. 1. The test should be a displacement test resembling

By Samuel M. Dunaway

INTRODUCTION ASARCO Incorporated purchased the East Tennessee Zinc Mines of the American Zinc Company and commenced operating on November 29, 1971. Presently, three mines are operating producing 6620 t/d (7300 stpd). The ore mined is sphalerite which occurs In lower Ordovician carbonates of the upper Knox Group and occurs in open space and fracture filling. Orebodies range from 3 to 46 m (10 to 150 ft) thick with dips from flat to 20º. The mining method is random room and pillar modified by shrinkage and bench stoping. Like other mining departments, the mining group at the Tennessee Mines Division is constantly looking for methods to improve productivity and safety and to reduce mining costs. This involves testing new equipment, trying new ore extraction ideas and making mining plant alterations to meet changes in operating conditions. The areas of change that will be described in this paper are longhole raising, jumbos and LHD loading, shaft sinking, conveyor transport of ore and sublevel haulage developments. LONGHOLED RAISES Raise driving has always been a hazardous occupation for miners and today it is becoming more difficult to get competent people for this kind of work. This problem has led us to seek an easier, safer way in which to excavate raises. The first longhole raises were excavated in the early 1970's using a Gardner-Denver air trac equipped with a PR-123 rock drill. The machine used 38 mm x 244 cm (1 ½ in x 8 ft) round rods with rope

Jan 1, 1977

By Theodore R. Butkovich, Jesse L. Yow

Geological storage of spent-fuel assemblies from an operating nuclear reactor has been underway since the Spring of 1980 at the U.S. Department of Energy's Nevada Test Site. The primary objective of this generic test is to evaluate granite as a medium for deep geological storage of high level reactor waste and to provide data on thermal and thermomechanical behavior of granite from imposed heat loads.(l) The underground installation in the Climax stock granite was sited at about 420 m below the surface and 145 m above the existing water table. As shown in Figure 1, three parallel drifts were excavated spaced on approximately 10 m centers. Seventeen storage holes were drilled at the central drift on 3 m centers in which eleven spent fuel canisters and six thermally identical electrical simulators were emplaced. Electrical resistance heaters were emplaced in vertical holes in the floor of the side drifts on 6 m centers. The thermal output of these heaters is being periodically adjusted to simulate the thermal response of a large storage array. Rock and ventilation air temperatures are being measured continuously in the drifts and throughout the rock surrounding the excavations. Measurements of drift deformation have been made routinely since the emplacement of the spent fuel. Both vertical and horizontal measurements are being taken at five locations along the heater drifts and at six locations along the central canister drift (Fig. 1). Two types of instrumentaton are being used: convergence wire extensometers which are monitored automatically, and a manually operated tape extensometer with which measurements are taken periodically. The tape extensometer measurements were initiated about 6 weeks following fuel emplacement. The lack of a temperature correcting capability for the convergence wire extensometers make that data unavailable for analysis at this time.

Jan 1, 1982

By T. N. Williamson

The art of drilling tunnels is still in its infancy, although it is 70 years since the first tunnel driver was put into operation. (It was used to drive 6000 ft of tunnel under the English Channel.) But during the next 60 years neither government agencies nor private enterprise could find much of a future in tunnel drivers. It was difficult to justify the heavy investments, labor was opposed to the machines, and there had been some spectacular failures. In the last ten years, however, there have been changes. Tunnel drivers are being tried with increasing frequency-in spite of the fact that a large number of them have had to be abandoned on site.

Jan 7, 1965

By AIME AIME

ENGINEERS in the past have been largely associated with private enterprise and there has been a considerable tendency on the part of some members of our profession to depreciate government service for engineers. We engineers must change our mental attitude about employment in government service, particularly in view of the present most friendly attitude of the U. S. Civil Service Commission toward engineers for major posts in our Government. We must also take a much more active interest in public affairs. It must be realized that the national-defense program, which we are now organizing, will require for its effectiveness large numbers of engineers skilled in a wide range of technical and administrative services. In fact, the success of this undertaking will depend largely upon the extent to which our Government can command expert engineering talent to serve during the emergency. There is an acute shortage of technical and supervisory engineering personnel not only in the industries concerned with national defense but also in the Army, Navy, and other defense agencies of the Government. By an Act of Congress, approved on Oct. 9. 1940. $9,000.- 000 was turned over to the U. S. Office of Education, the regular defense agency of the Government which has co-operated with higher education for

Jan 1, 1941

By N. Van Wingen

EFFective sand permeabilities can be ascertained from core analysis if the laboratory data are compensated to allow for the presence of connate or residual water. Such adjustments can be made by applying empirically derived correction factors. Effective sand permeabilities can be estimated also from analytical studies of field depth-pressure measurements. In one method the time rate of pressure build-up after a well is shut in from steady-state flow is required, and in the other the direct measurement of a steady-state rate of flow and the corresponding equilibrium pressure. The results of the investigation discussed in this paper demonstrate that these methods for determining mean effective sand permeabilities can be correlated. Introduction In recent years many investigators have demonstrated the practical value of an accurate knowledge of the physical and dynamical characteristics of reservoir sands containing oil and gas. Of these factors, which serve to completely define a porous medium as a container or carrier of fluids, the dynamical characteristics are of particular interest to the production engineer because they afford a direct measure of the rate at which the oil or gas content of a reservoir will become available. The constant that defines dynamically the porous medium as the carrier of a homogeneous fluid in viscous motion is the "permeability." Coke-analysis Method The generally accepted practice in com-piling permeability data has been to analyze in the laboratory core samples taken in the course of drilling through the productive horizon, and to obtain the mean measure of the productive ability or permeability for the interval open to production by graphical integration of the permeability profile. An average permeability ascertained in this manner, however, is useful to the production engineer only for comparisons of wells drilled in the same horizon, as permeabilities determined in the laboratory are measures of only the ability of a porous medium to transmit a single fluid. As a result of many investigations, it has been shown, however, that under actual reservoir conditions water is coexistent with the petroleum and that its presence greatly reduces the permeability of the sand to oil. Empirical relationships showing the effect of the presence of any immiscible fluid A (such as water) in a porous medium on the permeability of the medium to a fluid B (such as oil) have been established separately by Hassler,1 Dunlap,2 and the writer (Fig. I),3 so that the average specific or dry-core permeability as determined in the laboratory can be corrected to give the true measure of the ability of the horizon penetrated to transmit oil, provided the percentage of pore space occupied by connate water is known accurately.

Jan 1, 1942