Search Documents

By Larry DeGraff

With the increase of new mine development in the past several years, many coal mines have decided to self- perform the design and construction for their slope development projects. The development process of determining the proper configuration is challenging, and a major economical consideration. Greenbrier Smokeless Minerals engineering staff and consultants, along with DSI/American Commercial, developed a support configuration that was best suited for their slope. The developmental process took into consideration the length of slope, depth of slope at the high-wall transition, economics of a single or multiple entries, waterproofing, stresses on the steel supports and lagging during the backfilling operation. This paper describes the developmental concept of using a single entry, side by side configuration, using steel ?Banjo String? supports with steel plank lagging, to develop a long term permanent installation in a cut and cover application.

Jan 1, 2009

By D. Komljenovic, V. Kecojevic

Selection of the best possible truck type (model) is of crucial importance for the mine decision-makers. In this paper, authors contribute to the body of knowledge by developing a novel methodology for the selection of mining truck. Both the Coefficient of Technical Level (CTL) and Analytic Hierarchy Process (AHP) methods were used in this study. The CTL represents a mathematical function which takes into consideration the interrelations among the main technical parameters of mining trucks. The authors developed a hierarchical structure where both attribute categories and their importance, i.e. priority or weight in the selection process were determined. For each category, a number of sub-attributes and their priorities were assigned, and a pairwise comparison among them was performed using the AHP method. In the final part of the study, the CTL was integrated into the AHP and represents a holistic approach in the selection of mining trucks. A case study on 180 tonnes truck category offered by five manufacturers was carried out. A sensitivity study of obtained results was also performed indicating a very stable solution. The methodology presented in this paper may be used by mining operators to help in the selection of a specific type when acquiring a new truck. It may also be used by equipment manufacturers to help in analysis of potential benefits of envisaged modifications concerning an existing truck type and/or development of a new type.

Jan 1, 2007

By V. M. S. R. Murthy, Biswaraj Dash, Somnath Chattopadhyaya

Tunnel boring machine (TBM) has been in focus for the last few decades and is currently the most preferred excavation method for metro, hydro and irrigation tunnels. Tunnelling in hard and abrasive rock conditions, in particular, is adversely affected by a very low advance rate coupled with increased TBM disc cutter failures and cutterhead jamming, seeking an in-depth understanding of the design and operational processes of the boring components of the TBM. The cutterhead and disc cutter are the critical boring components of the machine, influencing the boring process significantly. These components directly interact with the rock and hugely influence the machine’s efficiency. This paper encapsulates a review of prior studies related to disc cutter design and the cutterhead design for hard rock TBM tunnelling. A design methodology for designing and selecting a disc cutter and a cutterhead is suggested. The design methodology has been applied for a hard rock tunnelling case, and suitable design specifications for the boring components were arrived at. The disc cutter and cutterhead specifications designed based on the suggested methodology closely match with that of deployed TBM specifications. It may be observed that except for the case of high-strength and high-abrasive rock (greyish quartzite), for the rest of the rocks, the suggested design can meet the desired advance rates.

Jan 31, 2024

By Kathryn C. Sole, Owen Tinkler

"Although the first large-scale application of copper recovery by solvent extraction (SX) took place in Zambia in the early 1970s, it is only in the last decade that this technology has become widely employed in this part of the world and is now a mainstay unit operation in most copper hydrometallurgical flowsheets. The mineralogy of the ores in the African Copper Belt, and hence the characteristics of the African leach liquors, differ significantly from those in Chile and the south-western USA, where copper SX has had a long and successful history. These differences provide operators, metallurgists, reagent vendors and engineers with many challenges: new approaches are needed to adapt this technology for successful implementation in this region. This paper examines typical operating practice in the African Copper Belt, discusses differences compared with other parts of the world and looks at some of the challenges and opportunities presented by these flowsheets. INTRODUCTION Following the success of the Rancher’s Bluebird and Bagdad solvent extraction and electrowinning (SX–EW) operations in Arizona in the late 1960s, the Tailings Leach Plant at Chingola, Zambia became the first large-scale copper SX plant in the world, commissioned in 1974. Despite the equipment design now being outdated, this plant still continues to operate successfully, indicating the versatility and adaptability of this technology. Today, there are some 75 copper SX operations worldwide with cathode production above 10 kt/a. The top ten producers currently account for some 40% of the global 4.3 Mt/a SX–EW copper production. South America (predominantly Chile and Peru) is the largest copper cathode-producing region, with annual production of some 2 Mt. The Central African Copper Belt (Zambia and the Democratic Republic of Congo (DRC)) is second, with cathode production of 1.2 Mt/a and North America (USA and Mexico) third, producing close to 0.8 Mt/a Cu (Cytec data, 2014). The remaining 0.35 Mt/a comes from all other regions combined (referred to as “Rest-of-World”). Current and future operations in Zambia and the DRC are summarised in Figure 1. The industry in this region is characterised by a large number of small (3 to 20 kt/a) plants, mainly Chinese-owned, and a few very large (>200 kt/a) operations, owned by major multinational corporations. This paper examines typical operating practice in the African Copper Belt, discusses the differences compared with other parts of the world and looks at some of the challenges presented by the conditions, as well as innovations in flowsheets, reagents and operating conditions that have been introduced in these circuits."

Jan 1, 2015

By C Maloloy-on, S Morgan, M Deiparine, H Mackie

There is a strong focus in the mining industry to limit its impact on water quality and usage. This is even more evident in developing countries, where mining companies operate within local communities and have to be diligent not to affect them negatively. In mineral processing operations, the vast majority of water reclamation occurs at the tailings thickener area and tailings storage dam. It is often more effective to maximise water recovery at the tailings thickener before material transport to the tailings dam. Tailing dams are relatively inefficient, and experience a high degree of water loss due to evaporation, seepage and water retention. In addition, tailings dams present the biggest environmental liability for mineral resource projects, so it is beneficial to limit their size and loading.In the past, it was common for tailings thickener areas to have a significant footprint with several large diameter conventional thickeners, producing underflows of between 45-55% solids (w/w). At times, these multiple thickeners were difficult to operate, leading to inefficiencies in water recovery and quality. The development of High-Rate Thickeners (HRT) has resulted in improved settling properties and HRTs usually operate at significantly higher solids loadings (= 1.2 t/m2.h) when compared to conventional thickeners (= 0.1 t/m2.h). Subsequently, thickener diameters have reduced in size and HRT technology has become the preferred option for thickener circuit design in both new and existing operations. HRTs also produce higher water recoveries with increased underflow densities = 55% solids (w/w).The Carmen Copper Corporation (“Carmen Copper”) circuit upgrade is a recent example of these HRT benefits, where one, 39 m diameter, Outotec HRT treats the solids flow rate of five 76 m diameter conventional thickeners. This has allowed operations to increase dry plant tonnage by 50%, maintain key performance targets and provide a framework for further plant expansion. This paper details the sustainable approach to the Carmen Copper tailings thickener upgrade, where metallurgical performance, cost-effectiveness and environmental impact were key considerations.CITATION:Morgan, S, Mackie, H, Maloloy-on, C and Deiparine, M, 2015. Carmen Copper – a sustainable approach to tailings thickener upgrades, in Proceedings MetPlant 2015, pp 416–430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By V. Prostakova, M. Shevchenko

The copper smelting gas / slag / matte / metal / solids system with the Cu-Fe-Ca-Si-O-S major elements has been a long-term focus of the present overall research program using integrated experimental and modelling approach for the phase equilibria characterisation and development of a thermodynamic database. A systematic investigation of phase equilibria of slag systems in equilibrium with Cu metal is providing information for systems where copper coexists in slag with lead, zinc, and aluminium oxides as major components. Experimental studies involve high-temperature equilibration of synthetic samples; rapid quenching; and measurement of the compositions of equilibrium phases using electron probe X-ray microanalysis (EPMA). Particularly important feature of the present study a wide range of temperatures (660-1670°C) being characterised that reveals major inconsistencies in the existing thermodynamic description of the multicomponent system, and allows to establish the thermodynamic properties from phase equilibria in a reliable way. FactSage-based thermodynamic modelling is integrated with experimental research. Initial thermodynamic assessments are used to identify priorities for experiments, planned to provide specific data for thermodynamic optimisation. Significant improvement in the accuracy of the phase equilibria description is achieved, in particular in the PbO-Cu2O-SiO2, ZnO-Cu2O-SiO2, and Cu2O-CaO- Al2O3 systems in equilibrium with metallic Cu. INTRODUCTION Slags high in lead and copper are generated in primary metal production in the smelting of lead sulfide concentrates and in pyrometallurgical metal recycling systems. The compositions of these slags are varied due to increased fraction of recycled materials in the feed as well as introduction of previously unused chemical elements to modern technology. Therefore, their processing becomes chemically more complex; in that way they contain a large number of different metals. These slags form complex non-ideal solutions (with possible formation of several immiscible slags) that can coexist with stoichiometric solids, solid solutions, mattes and molten metal depending on the bulk composition and process conditions. Predicting the outcomes of smelting and refining processes is becoming increasingly difficult. To assist in the optimisation of these metallurgical processing operations, a comprehensive research program is underway to develop accurate thermodynamic databases for these non-ferrous process systems.

Jan 1, 2019

By Abdul Aziz Hanifah

A novel instrumentation and analysis technique, called GLOSTREXT method has recently been introduced for bored pile load tests in Malaysia. This technique provides an innovative and improved alternative for conventional bored pile instrumentation methods commonly practiced for the past few decades. Results for five case histories involving full scale static load tests for high capacity bored piles with both new and conventional instrumentation details placed in within the same instrumented piles are presented to demonstrate the advantages of this novel technique. Results show good agreement between the new and conventional instrumentation.

Jan 1, 2006

Total mechanisation in the Western district of New South Wales is quite a recent addition to productive methods in that State, for it was only in 1940 that the first colliery was equipped for this method of winning coal. Now almost all mines either are totally mechanised or are planning to get their coal by these means.This marked change in recent years is explained by the salient features of the industry's history. Collieries in New South Wales had generally been subjected to low selling prices forced on them by over-production and severe competition. Little money was available out of profits to purchase machinery, and returns on capital were so poor that inducement to invest money in the industry was nonexistent.The second world war brought price fixing at the already low prices. It was not until the post-war period that there has been any inducement to mechanise.Much credit for mechanisation can be given to the Joint Coal Board, a government body formed in 1948. Pursuing a broad plan for the rejuvenation of the industry, this Board, purchased large quantities of machinery for use in, mines under hire-purchase agreement. These agreements encouraged machine mining, and this fact, together with the ensuing production economies, has improved the financial position of the industry.The Board has also been instrumental in the granting of increases in the fixed price of coal, so that the industry has been given an even greater boost in the direction of mechanisation.

Jan 1, 1954

By Clifford H. Summers

This report describes an experimental program which we conducted on behalf of the U. S. Bureau of Mines, to select from currently available materials two novel systems of construction for air-restraining bulkheads to be used in control of radon-polluted air in underground uranium mines. The program included both laboratory and field tests, the latter conducted in a portion of an operating mine owned and operated by Union Carbide Corporation at LaSal, Utah. The test site was a worked-out, double entry stope having a Volume of about 2000 cubic meters, and was located immediately adjacent to an exhaust airway. The bulkheads were constructed of 15 cm x 1.5 cm timber uprights, 5 cm x 15 cm horizontal members supporting a close-fitted 13 mm plywood curtain-wall., which was covered with a low-permeability membrane to seal in the radon-polluted air. The two membrane materials selected for testing were chosen from a list of twenty-two potentially acceptable candidates using criteria such as strength, flammability, ease of application, adhesion, radon permeability, and elasticity. Thirteen of the candidates were tested in our laboratories for adhesion to plywood and to both wet and dry concrete (simulating wet and dry mine rock surfaces), and for their general physical properties, including radon permeability. The final selections made by the Technical Project Officer, and based on our recommendation, were a pre-formed ethylene propylene diene monomeric rubber (EPDM) membrane 1.12 mm thick, normally used as a roof sealant in industrial construction, and available from Carlisle Tire and Rubber Co., Division of Carlisle Corp., Carlisle, PA, and Aquafas 48-00, a water-based mastic used in a wide variety of commercial applications and available from H. B. Fuller Co., Foster Products Division, Spring House, PA. The EPDM membrane was applied as a single sheet, laminated (dry) between two layers of plywood, and the Aquafas was applied both by troweling and spraying onto a plywood surface. In the field test, radon concentrations were continuously measured before, after, and in the trapped air behind each bulkhead. Temperature, pressure, and velocity of the air in the adjacent airway were also measured and recorded continuously. Radon fluxes at the rock/air interface and through the bulkheads themselves were measured manually on a frequent basis. All continuously acquired raw data were recorded automatically on two USBM Data Aquisition Systems (DAS), and the raw data were converted into engineering units and recorded on magnetic disks by a specially programmed microcomputer that was interfaced with the DAS's. Relatively clean (i.e. low radon concentration) air was pumped into a point near the face of one test bulkhead from a location 170 meters away through vent bag. Several air curtains and two air-restraining bulkheads were erected in passageways adjacent to the test area in an effort to control both velocity and radon concentration of the air flowing past the bulkhead faces. An average concentration of approximately 500 pCi/liter at a flow of 550 m3/minute was attained as the background concentration against which leakage through the bulkheads was measured. The entire field test period extended from October, 1981 to March, 1982, a total of six months, and was subdivided into seven successive time periods: 1) site preparation 2) background measurements prior to bulkhead construction 3) passive restraint, with bulkheads in place and totally sealed 4) open bleeder period of natural convection ventilation in and out of the bulkheaded area through a 10 cm (diameter) opening, with connecting tubing; leading into an Exhaust airway 5) open bleeder period, having forced exhaust through a 1.0 cm opening using a servo-controlled fan 6) charcoal trapping period, using the servo-controlled fan to exhaust air through the charcoal traps, to test the effectiveness of such traps in removal of radon from the exhausted air 7) site decommissioning Each of the two systems tested, one incorporating the pro-formed EPDM-rubber membrane and the other utilizing Aquafas 48-00, was assessed for effectiveness in controlling radon-polluted air by observing the change in the radon concentration in the ventilation air flowing continuously over the surface of each bulkhead. The sensitivity of the observed measurements was limited by the volume flow-rate of the ventilation air and the radon concentration in that air. The data would indicate that the observed increments in radon concentration in the ventilation air moving across bulkheads B-l and B-2 were essentially zero within the limits of sensitivity of the measurements. Data from radon flux measurement taken both on the sealed ribs adjacent to the bulkheads and on the bulkheads themselves did not differ significantly from blank data.

Jan 1, 1982

"In mining operations, it is widely accepted that strategies to drive operational goals must revolve around improving plant availability, reliability and process efficiency. In this paper, an integrated solution framework for reducing process variability, increasing process efficiencies and maximizing plant availability and reliability is discussed within the context of a typical milling circuit. The framework exploits a real-time analysis “gap” evident in production operations that prevents timeous identification of equipment and process failures. This is achieved by leveraging predictive analytics for equipment health monitoring, control loop monitoring and advanced regulatory control solutions towards enhanced process performance, improved asset management and regulatory compliance. The framework provides for early and actionable warnings on equipment and process degradation using real-time operational data.INTRODUCTION The changing landscape of gold mining and processing presents many challenges that threaten sustainability of existing (marginal) operations as well as deter investment in new projects. As existing “shallow” ore resources become depleted, mining operations are increasingly treating low-grade ores with complex and randomly variable mineralogical characteristics. For example, in South Africa, historically one of the major gold producers, the average grade of ore treated has been decreasing from averages above 4.5 – 5 g/t to current grades averaging less than 3 g/t within a decade (Chamber of Mines, 2012). Moreover, lower tonnages are being treated as a result of the narrowing of the available resource base. Also, the regulatory framework has tightened over the years due to heightened concerns on the safety, health and environmental impacts of mining and related activities."

Jan 1, 2014

By John D. Carr

Introduction The Flin Flon zinc plant operates on what is known as the low density or standard sulphate process, that is, the zinc is carried through the plant solution circuit attached to the SO4 or sulphate radical at a concentration not exceeding 175 grams per litre zinc. The process may be described briefly as follows: The zinc is received in the zinc concentrate chemically combined with sulphur and mixed with many other impurities. The concentrate is roasted and most of the sulphur is burned to a gas, which is discharged from the plant. The roasted concentrate, or calcine as it is called, is leached with a weak sulphuric acid solution so that the resulting leach solution contains a high zinc content but a very small proportion of the impurities. The solution is separated from the solids and is purified further by agitation with zinc dust to remove copper, cadmium, and cobalt. This purified zinc sulphate solution is then pumped to the electrolytic department. The solids from the first leach are again leached, but this time with a stronger acid solution to dissolve all of the remaining zinc which is soluble in the strength of acid available. The solids and solution from the leach are then separated. The solids are stock-piled for further treatment at some future date and the solution, carrying a relatively high amount of impurities, is sent to the first leach, where the chemical action is such that the contained impurities are precipitated as solids. The electrolytic department is nothing more than a large number of electroplating cells in which the zinc is plated on aluminium sheets. Since zinc does not plate tightly to aluminium, the zinc plating or sheet is easily stripped from the aluminium and the sheets are collected to be melted and cast into the standard market bars or slabs. In the electro-deposition cells, the zinc sulphate (ZnS04) is split to metallic zinc (Zn) which plates out, and sulphate (S04) which combines with the hydrogen of the water of the solution to form sulphuric acid (H2S04). When one pound of zinc is deposited, about one and one-half pounds of sulphuric acid are formed. This acid is sent to the leaching section, where it dissolves one pound of zinc from the calcine. The solution is purified and is again pumped to the plating cells. The solution travel forms a complete circuit.

Jan 1, 1935

By Deepak Vidyarthi

This paper deals with the significance of Explosive Energy in the optimization of blast design parameters, and the benefits emerging out of it. It is based on the original work done by the author in developing and successfully implementing a site-specific software package on ‘Blast Design Optimization’ at Kudremukh Iron Ore Mine in India with a production level of 22.5 million tonnes of crude ore and off-take of Explosives of approximately 5500 tonnes per annum. The software package has yielded tangible results in effecting reduction in Explosive Consumption, substantial savings in the Cost of Explosive, besides Environmental Improvements by way of attenuation of Blast Induced Ground Vibrations as well as Air-Blasts. By carrying out regular ‘Regression Analysis’, and determination of the Rock Constants, it has been possible to further develop software packages as well as prediction curves for prediction of Peak Particle Velocity, Safe Charge of Explosive, Air-Blasts etc. A model has also been developed for the prediction of ‘Fly Rock’ although at KIOCL, fly rock does not pose any problem.

Jan 1, 2006

By Carlos Virrueta Zevallos

El presente texto describe los lineamientos necesarios para construir un sistema de control de perdidas sólido en la Corporación HOCHSCHILD MINING DNV, el cual se basa en un liderazgo, compromiso y administración efectiva del sistema como puntos vitales para el éxito, protegiendo la vida de las trabajadores, la propiedad, los procesos y medio ambiente.

Sep 12, 2011

By Keith Mayhew

Ante la alta demanda de cobre por el crecimiento urbano e industrial y para la construcción de infraestructuras, la industria del cobre necesita una solución para el desarrollo sustentable de los recursos minerales de cobre con alto contenido de arsénico. En ese sentido, Teck Resources Limited (Teck) y Aurubis AG (Aurubis) están trabajando juntas para desarrollar una tecnología que sea aceptable desde los puntos de vista regulatorio, medioambiental, social y económico. Por ello, el presente trabajo señala los resultados obtenidos por Teck-Aurubis conjuntamente, como consecuencia del programa técnico desarrollado desde 2010 para el tratamiento con éxito de concentrados de cobre con alto contenido de enargita usando la tecnología CESL.

Sep 12, 2011

By F. Khorram

Image processing is a technique that simulates the human vision system. This technique enables applying every statistical or intelligent operation to recognize differences. In this way this new technique is used in quality control systems in most industries. Studying sedimentary rocks is very important from the economic point of view. Some units of sedimentary sequences involve different mineral deposits, hydrocarbon and water resources. Therefore it is important to identify and classify different sedimentary rocks. Descriptive classification of sedimentary rocks is usually based on visual and textural features and chemical composition of a sample. In this paper different samples of a limestone mine in central part of Iran are classified. The samples were collected from different parts of the mine and crushed down in size from 2.58 cm to 3.58 cm. The rock samples were labeled based on percentage of chemical and lithological compositions. Each sample was assigned to one of the distinguished groups. The images of the samples were taken in appropriate environment and processed. A total of 74 features were extracted from the identified rock samples in all images. In order to feature dimensional decrease, principal component analysis method was used. Then Bayesian statistical algorithm was used as a useful tool for classification. Classification Correctness Rate (CCR), calculated for the test data sets are %88, %68, %61 and %72 for the first to fourth class respectively. Therefore it can be inferred that the extracted features of images are appropriate indicators for different samples identification. These precise results besides the advantages of image processing technique, which are increasing speed of operation and decreasing cost, appears to be a desirable success.

Jan 1, 2012

By Robert McClure

The detection, recovery and disposal of commercial explosives and explosive waste has always carried a level of risk and requires specialized equipment and technical expertise. Improperly stored, discarded, deteriorated, misfired, stolen or surplus products are often the primary sources of explosives that require safe disposal. Detection and disposal tools available today have advanced significantly due to developments in Counter-Improvised Explosive Devices (C-IED) operations and commercial blasting technology. These technologies have provided safer more efficient ways to detect, investigate and dispose of commercial explosives products in order to minimize property damage and potential harm to disposal personnel and the general public.

Jan 1, 2015

Abbey, Robert Graham, District Mgr., The W. W. Sly Mfg. Co., 50 Church St., New York, N. Y. '21 Abbott, A. N Ave. Morelos 84, Cuernavaca, Morelos, Mexico '23 Abbott, Argyle Campbell, Geol 42 Everett St., Arlington, Mass. '29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Consolidation Coal Co., Watson Bldg., Fairmont, W. Va. '15 Abeel, George H., Jr., Cons. Min. Engr 1281/2 S. Canon Dr., Beverly Hills, Cal. '18 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh. .Pittsburgh, Pa. '28 Abel, Walter D., Cons. Engr 650 S. Grand Ave., Los Angeles, Cal. '82 Abele, Louis T., Min. & Met. Engr., Supt., Texas Hill Mine Coulterville, Cal. '31 Abell, Leo M. Millicent, S. Australia '31 Abernathy, George Elmer, Prof. of Geol. & Min., Kansas State Teachers College, Pittsburg, Kan. '20 Aborn, Robert H., Research Lab., U. S. Steel Corp. Lincoln Highway, Kearny, N. J. '19 Abozeid, Mahmood, Dept. of Mines & Quarries Cairo, Egypt '26

Jan 1, 1932

By R. S. McClain

The Federal Bureau of Mines investigated residues from aluminum plants, to determine if carbon could be removed by flotation while recovering fluorine and aluminum compounds for recycling to the reduction process. This publication summarizes studies on samples representing three types of plant waste products, supplied by three aluminum-producing companies. Samples of flue dust, pot skimmings, and pot linings from the various plants all responded to a simple turpentine flotation scheme to reject 90 to 97 percent of the carbon. Aluminum compound recoveries ranged from 42 to 94 percent on the flue dust, were about 95 percent on the pot skimmings, and ranged from 75 to 89 percent on the pot linings. Fluorine recoveries from the same samples ranged from 35 to 63, 92 to 95, and 77 to 86 percent, respectively. The pot linings contained soluble salts of aluminum and fluorine which were recovered by precipitation with sodium aluminate and carbon dioxide gas. Composites of residues from each plant responded to flotation much the same as the individual samples. Aluminum is produced by the electrolysis of alumina in a molten cryolite bath. The electrolytic reduction cell consists of a carbon-lined box containing a pad of molten aluminum which serves as a cathode, a carbon anode, and an electrolyte of molten cryolite in which the alumina is dissolved. Alumina is reduced to aluminum at the cathode, and carbon is oxidized at the anode.

Jan 1, 1961

By A. Lebedev

Application of dynamic simulation for a base metal processing plant is discussed. The plant receives ore of variable quality from two pits and blending had to be applied to maximise recovery. The plant employs multiple stage crushing, screening, dense media separation, two-stage milling, flotation and further filtration. Stockpiles and bunkers are used in the plant to cater for breakdowns and operating delays, the latter being appropriately incorporated in the model. A detail dynamic simulation model was constructed from the rock face to the filtration plant to assist the plant design, notably with definition of the ore blending method, sizing storage capacity and in-plant conveyors. The plant model was broken down to capital equipment items and various feed types and mass balances were tested to ensure that the production target is met. The dynamic simulation tested the proposed blending method, identified bottlenecks, produced risk profiles for all strategic storage facilities and overall helped minimise the project risks and improve confidence in the plant design. Keywords: Dynamic simulation, ore grade, blending, capacity, risk profile, throughput, utilisation

Jan 1, 2020

By C. Alexander

Stillwater Mining Company is developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in south central Montana. A 5650 meter (18,550-foot) tunnel is required to gain access to the ore bearing horizon (J-M Reef). Access and primary mine development can be accelerated through the use of two 4.6 meter (15-foot) diameter tunnel boring machines (TBM). One TBM was purchased new while the other was purchased used. Machine specifications, site support facilities, portal/launch chamber construction, TBM assembly, startup and operation are discussed in this paper.

Jan 1, 1999