Search Documents

By Robert J. Coutts, Dan A. Payne

"The Broadmeadow mine is a punch longwall mine owned and operated by BHP Billiton Mitsubishi Alliance (BMA) in the Bowen Basin of Queensland, Australia. In 1999, an exploratory adit was driven as part of the feasibility study for the establishment of the mine. Subsequent development of the mine in 2004 started some distance away from the initial test adit. Ten years later, the trial adit would be used as the headgate of the 5'h longwall panel. However, multiple roof falls had occurred in a heavily jointed area over a distance of 1, 000 ft (300 m) during the past 10 years. Due to the immediate coal roof, low stress environment and time, some of these falls had progressed to 38 ft (11.5 m) above the mining floor. As a result of the extensive work involved and safety implications of trying to recover the roof falls conventionally, a strategy was developed to fill these roof falls with a cement based product from the surface, down boreholes, and redrive the roadways through the consolidated roof fall material. This paper describes the process of rehabilitating these roadways, the results when the roadway was redriven and the headgate performance as the longwall mined through the area.INTRODUCTIONBMA operates 7 open cut and 2 underground mines in the Bowen Basin of Queensland, Australia producing over 50 mt per year of high quality coking coal. As a result, BMA has established over 150 miles (250 km) of open cut highwall.Broadmeadow Mine is a punch longwall mine located 22 miles (35 km) north of Moranbah in Queensland, Australia on the western limb of the Bowen Basin Coal Measures (Figure 1). Broadmeadow Mine commenced development in 2004 and began longwall operations in 2005. Broadmeadow is currently completing the fifth longwall panel and produces over 4 Mt per year of high quality coking coal. Mining is undertaken in the Goonyella Middle Seam, which is 21 to 25 ft (6.5 to 7.5 m) thick in the current mining area.The mine layout required the use of an old exploratory gateroad as the headgate of its 5th longwall. This gateroad had experienced numerous large roof falls and required extensive rehabilitation."

Jan 1, 2010

By David F. Gearhart

A cooperative study was conducted between Signal Peak Energy and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the behavior of a pre-driven recovery room under less than 200 ft of cover. The design of the support systems for a pre-driven recovery room must provide control of the roof and ribs during the changing stress environment experienced throughout the final advance of the longwall into the recovery room. It must also provide a stable area where mine personnel are not exposed to undue hazards during shield recovery operations. This recovery room was constructed in two phases; each phase mined a 21-ft-wide room that was heavily supported, and subsequently fully backfilled with 800-psi, cellular concrete. Instrumentation to monitor the recovery room performance included borehole pressure cells (BPCs) placed in the head gate and tailgate pillars, at four locations across the longwall panel, in the fill material, and in the first row of outby pillars near the center of the panel. Four roof-to-floor convergence sensors were installed in the back fill material and a vertical, multipoint borehole extensometer (MPBX) measured the displacement of the strata above the recovery room. Surface surveys were conducted to measure MPBX collar movement. The data show that the front abutment load was transferred onto the recovery room backfill and the out by pillars as the longwall panel was extracted. As the longwall approached the recovery area, the fender and shields yielded, but the backfill provided enough support to keep the room stable as the longwall advanced to its final position. The system worked as planned and the face was recovered in record time.

Jan 1, 2014

By Andre Zingano

An underground mine using room and pillar and retreat mining methods was developed during the 1950?s. In 2009 an open cast mine was opened in the same reserve with the objective of mining five coal seams including the one previously mined. Recently, a series of slope failures were detected at the open cast mine. The surface mine map was overlain on the underground mine map, and it was observed that the slope failures were located above a retreat mined area where the overburden had caved and the ground subsided. The deformation and displacement attributable to subsidence caused a loss of strength in the overburden strata. The objective of this paper is to study the causes of slope sliding (or failure) due to the ground subsidence of rock layers above oldmined out areas. A map was created to overlay the two mines -- the abandoned underground mine and the active surface mining. Two- and three-dimension numerical modeling was conducted to simulate the slope behavior and to verify whether the mine subsidence was the cause of slope instability. This study indicated that the subsided rock layers were the cause of slope instability and sliding.

Jan 1, 2013

By WenFeng Li

Comparing to the coal seams in Eastern China, the coal seams in Western China usually have better geological conditions. Therefore, changes in the conventional gateroads layout are required for the Western longwalls. A case study based on a Western coal mine (LiMin) was presented to discuss the feasibility of an innovative gateroads layout. Based on the geological conditions, a 5m wide pillar between the adjacent two longwall panels, 09112 and 09113, was proposed in order to increase the recovery rate. More importantly, the entry supporting strategy of panel 09113 headgate needed to be determined and verified carefully since only 5m wide pillar was left to separate the entry from the panel 09112 gob. Three strategies with different supporting intensities in the panel 09113 headgate were evaluated by numerical modeling. The model outputs indicated that roof and rib boltings plus single hydraulic props were essential to maintain the gateroads stable. Field observation showed that under the proposed entry supporting strategy, the total roof-tofloor and rib-to-rib convergences were only 360mm and 460mm, respectively, during the service life of the panel 09113 headgate, which indicated that the innovative gateroad layout proposed in this paper is suitable for longwalls with similar geological conditions in Western China.

Jan 1, 2013

By Anthony Iannacchionc, Jessica Benner, Harold Miller, Megan Witkowski

"Longwall bituminous coal mining has been practiced in Pennsylvania since the 1970""s. Hundreds of longwall panels have been mined during the last 40 years but only 24 have actually undermined Pennsylvania's Interstate Highway System. The impact to interstate highways are summarized in this paper and the factors that influence the magnitude of these impacts are examined.INTRODUCTIONOver the last 30 years, interstate highways in Pennsylvania have been undermined by portions of 21 bituminous coal mine longwall panels. From 2003 to 2008, three of the panel were extracted by the Emerald Mine and six by the Cumberland Mine both in Greene County and both owned by Alpha Resources. Previous assessments of longwall mining under Pennsylvania’s interstates have identified impacts to the highways but no danger to public safety. In general the magnitude and extent of impacts during the recent undermining of Interstate 79 or 179 appears to be similar as those identified in previous studies. The nine longwall panels are among some of the widest in the U.S. They are supercritical in character with overburdens ranging from greater than 152 m (500 ft) to less than 305 m (1,000 ft).The Pennsylvania Department of Environmental Protection (PA DEP) requested that the University of Pittsburgh summarize observations collected by their staff during the recent undermining of 179. Observations and photographs of impacts to the highway were made by PA DEP staff and entered into reports prepared by California District Mining Office (COMO) staff and statements written into the Bituminous Underground Mining Information System (BUMIS) database. In addition to the observations by the PA DEP, the Pennsylvania Department of Transportation (PennDOT) conducted a series of detailed land surveys along portions of the highway undermined from 2003 to 2008. To characterize the subsidence basin fanned by longwall mining. PennDOT information has been analyzed by another research group within the university (Guticrre7, et al., 20 I 0)."

Jan 1, 2010

By Guo Wenbing

"INTRODUCTIONThere is a great amount of coal (about 140 billions tons) left unmined under the surface structures, water bodies, railways (referred to as the “three-body”). Coal mining under “threebody” especially that under surface structures has become a major problem in the mining area. The key problem of mining under surface structures is to control overburden strata and surface movements. At present, the major surface subsidence control methods are strip pillar mining, backfilling mining method, room and pillar mining, grouting of bed separations, harmonic mining, and so on. Wongawilli mining method is a high-efficient shortwall mining method developed based on the room and pillar mining, and named after the first successful trial in Australia “Wongawilli” coal seam. The room and pillar mining equipment such as continuous miner is employed in this method. Its major advantage is flexible face layout. It can be used to mine the small wedge coal blocks and those that are difficult to be mined with retreat longwall mining method. It requires less capital investment, short lead time for production, flexible equipment operation and face move and high productivity. It has been applied in some China’s coal mines.The “Wongawilli strip coal mining technology” is a new coal mining method for mining under surface structures. It combines the strip mining longwall layout and Wongawilli high efficient mining technology. This technology can fully utilize the advantages of both the strip pillar and Wongawilli mining methods, and overcomes the disadvantages such as frequent face move, and low mining efficiency in strip pillar mining, and poor ventilation condition and poor long-term stability problems of coal pillars. In this paper, the Wongawilli strip mining method was designed for Wangtaipu mine and its feasibility was studied using numerical modeling and surface subsidence prediction.Geological and mining conditionsAt present, most of the No.15 coal seam reserves totaling 377.07 million tons in Wangtaipu mine are located under surface structures. In order to mine the coal under the surface structures, the Wongawilli strip mining method was employed. An appropriate panel was selected for trial and the surface movement monitoring lines were set up. The trial area is located in panel XV2214 (East) ( re 1). In this area, the floor elevation of coal seam is +634~646m, the surface elevation is +810~817.5m, and the average depth of coal seam is about 174m.The average panel length is 282m and average panel width is 73.5m. The seam dips 1~3° and is 1.8~2.5m thick with an average of 2.15m. The roof and floor rock characteristics are shown in Table 1."

Jan 1, 2015

By Mark Van Dyke, Gamal Rashed, Khaled Mohamed, Timothy Barton, Morgan Sears

"The unconfined compressive strength (UCS) of coal is an important parameter that controls the stability of coal ribs in underground mines. Estimation of the UCS of coal units composing the rib is required for conducting the rib stability assessment technique. This technique requires conducting large numbers of conventional UCS tests in a laboratory, which are expensive and time consuming. The research work outlined in this paper examines the use of indirect strength estimation methods—the point load test (PLT) and the in-situ Schmidt hammer test (ISHT)—for evaluating the intact strength of coal. The conventional UCS test was conducted on 80 coal specimens from 10 different coal seams for eastern coals. For each coal seam, the PLT and the ISHT were compared with the UCS test results to establish a correlation between the strength indices from the PLT or ISHT and the UCS. Moreover, to simplify the estimation of the UCS, a correlation between the megascopic coal lithotype and UCS was established.INTRODUCTIONBased on Mine Safety and Health Administration (MSHA) reports, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States over the past decade (MSHA, 2018). In an attempt to control rib failures in underground coal mines, the National Institute for Occupational Safety and Health (NIOSH) is working on developing a coal rib stability rating technique to provide a quantitative means to characterize the stability of coal ribs and to provide guidelines for early selections of rib support. The unconfined compressive strength (UCS) of coal units composing the ribs is one of the key input parameters required to estimate coal rib stability. The UCS of coal is an important parameter that controls the resistance of coal ribs to fracturing and slabbing. Direct determination of the UCS is time-consuming and expensive. Moreover, the UCS may be limited to testing only the strong coal samples since the weak or highly cleated samples might not survive the transportation and the preparation process (cutting and grinding). Therefore, alternative methods have been tested to indirectly find the intact strength of coal, such as the point load test (PLT) and the in-situ Schmidt hammer test (ISHT). The acronym ISHT refers to Schmidt hammer tests that were conducted in-situ on coal pillar ribs, while the acronym SHT refers to tests that were conducted on small scale blocks of coal."

Jan 1, 2018

By Thierry Lavoie, Mark K. Larson

"Engineers at the National Institute for Occupational Safety and Health (NIOSH) and Itasca Consulting Group, Inc., conducted a study to determine the procedure for calibrating a caving model implemented in FLAC3D. The model is calibrated to measured surface subsidence. This sedimentary caving model was developed by Itasca for NIOSH for the purpose of more closely simulating mechanical processes during caving. When a model is considered calibrated to surface subsidence, the load between the extracted panel's roof and floor is a reasonable estimate of gob loading. Such information can also provide an estimate of the amount of overpanel weight that is transferred to the abutment. This load distribution is a parameter needed, for example, to estimate loading of pillars in longwall gate roads. For the current case, a calibrated model resulted in a calculated abutment angle of 30.6°considerably higher than the assumed value used in empirical methods, but reasonable considering the presence of massive stratigraphic members in the overburden. Because of additional information available after this study that the extracted seam height was actually greater in the first panel, a corrected range of abutment angle was estimated to be from 27.7° to 30.6°, still significantly higher than the empirical assumption. The expectation is that better estimates of abutment loading profiles will result in improved evaluations of mine layout design and, therefore, reduce the number of fatalities and injuries resulting from falls of ground.INTRODUCTIONThe safety of miners in underground coal mines depends on careful consideration of the mechanisms involved in failure and transfer of load. The successful design of pillars and panels in longwall and room-and-pillar coal mining requires thorough attention to any information and measurements available that help understand these mechanisms. Although empirical methods, such as Analysis of Pillar Stability (ALPS) Mark (1987); (Mark, 1992) or Analysis of Retreat Mining Pillar Stability (ARMPS) (Mark and Chase, 1997), can provide a sense of success or failure, complex geology and failure in the roof or floor material or complex material behavior of the coal can make evaluation by an appropriate numerical modeling tool necessary. The numerical tool must simulate important mechanisms and appropriate detail that underlie the mechanism. For example, Starfield and Cundall (1988) advised using ""the simplest model that will allow the important mechanisms to occur, and could serve as a laboratory for the experiments you have in mind."" To that end, data gathering about the geology, geometry, and material behavior is very valuable. Such data facilitate selection of an appropriate model and model inputs. Moreover, this data facilitate improved assessment of risk to miners and how to minimize that risk."

Jan 1, 2016

By Baogui Yang, Jie Yang, Anthony Iannacchione

"The cemented coal gangue-fly ash backfill technique (CGFB) has commonly been used to control subsidence damage caused by underground coal mining. This paper discusses the CGFB backfilling process used at the Xin-Yang coal mine, Shanxi Province, China. A general description of the components of the CGFB are provided. The reaction of the strata to the backfilling process is simulated with a scaled physical model based on the Xin-Yang conditions and verified with subsidence points on the surface. With the help of the cemented filling materials, the CGFB produces only a slight bend to the overburden roof strata over the longwall panel. Physical models were constructed at the China University of Mining and Technology, Beijing, to simulate actual conditions. The modeling results show minor fracture distribution in the overlying strata and lower abutment pressure development within the backfilling area. The effectiveness of the CGFB technique is verified by a reduction in the vertical surface subsidence measured above the backfilled area.INTRODUCTIONUnderground longwall mining is the most efficient underground means to recover coal resources and is used widely in China, the US, Australia, and Europe. However, this type of mining has introduced some serious environmental impacts. Perhaps the most significant environmental issues are the surface and groundwater impacts associated with the formation of the subsidence basin (Bell and Donnelly, 2006). Backfill technology has been used for years to mitigate subsidence impact. Simply speaking, the backfilling technique places filling materials into the void left from the extraction of coal. When this material is placed within the gob, it is capable of partially supporting the overburden until a new equilibrium is reached. Essentially, the backfill material inhibits crack development and expansion caused by the strata movement and mitigates damaging ground deformations.The cemented gangue-fly ash backfill (CGFB) is one type of novel backfill technology, consisting of cement, coal gangue, fly ash, water, and additives in varying concentrations. The CGFB is mixed on the surface, pumped underground through a pipeline as a slurry, and placed in the void behind the longwall shield under the protection of specially designed hydraulic supports."

Jan 1, 2018

By Yongping Wu

Roadway deformation and stress migration occur with uncertainty and randomness because of geology, tunneling and mining influence. In order to study the surrounding rock deformation and failure mechanisms in three-dimensional stress state, an air return roadway of Yuanyang Lake mine of Shenhua Ningxia Coal Industry Group Co., Ltd. was chosen as a research object. The three-dimensional model was a designed and completed experiment with a dynamic-static coupling load. The model was loaded by hydraulic cylinder, simulating the in-situ rock stress field and the induced stress field of surrounding rock. The deformation monitoring system of the roadway model was constituted by optical total stations, borehole observation instruments, acoustic emission monitoring, and stress sensors. A wealth of data was obtained through an omni observation of surface displacement, characteristics of stress distribution, and deformation and failure of surrounding model material. By acoustic-optic-electric methods, a real-time testing on physical, mechanical, and damage parameters was realized through the experimental process. The results showed that the data of deformation and failure obtained from the deformation monitoring system of the roadway were authentic, which has great significance for warning and forecasting safety hazards of surrounding rock in coal mines.

Jan 1, 2013

By Tristan H. Jones

Rib-related accidents in underground coal mines continue to cause injuries and take lives at a rate of 1.3 fatalities per year for the last 17 years. Prevention of these accidents cannot simply be a matter of installing more rib support, though the eventual final solution will undoubtedly include that component. Ultimately, rib safety will be brought about through an understanding of the causes and mechanisms that cause rib fatalities, and by fine-tuning mining methods and procedures that are currently in place. This paper investigates the factors likely to be most influential in the occurrence of rib fatalities. A careful analysis has been conducted of the rib fatality reports documented by the Mine Safety and Health Administration between 1996 and 2013. The primary outcome is the determination of the relative impact of each type of rib fatality factor and a better understanding of the impact each factor has. Among the rib fatality factors considered, the influence of rib profileis considered for the first time. Mining height, rib stratigraphy, mining cycle, and the standing position of a miner next to a pillar are also considered. Questions are also raised about the current interpretation of rib fatalities due to mining depth, with the indication being that mines operating at the greatest depths may actually have the most respectable rib fatality record among all mining depths. Additionally, a new method of considering rib exposure is developed. Based on the results, recommendations are made for future work. By gaining a better understanding of how particular factors contribute to rib fatalities as opposed to rib failure or stability, it is hoped that future efforts can be more precisely directed towards the desired outcome of fatality reduction.

Jan 1, 2014

By Joe Wickline, Mark A. Van Dyke, Wen H. Su

"Geological factors and mine design contribute to mining-induced seismic activity, and this is especially true in longwall mining. Massive rock units are a key cause of seismic activity due to catastrophic failures that release large amounts of energy. Other factors, such as overburden depth, panel design, pillar design, rock strength, and proximity of the massive rock unit to the coal seam, all have a role in the potential and size of a seismic event. A recent seismic event was recorded by a deep longwall mine in Virginia at 3.7ML on the local magnitude scale and 3.4 MMS by the United States Geological Survey (USGS) in July 2016, which had no impact on the mining operations. Further investigations by NIOSH and Coronado Coal researchers have shown that this event was associated with geological features that have also been associated with other, similar seismic events in Virginia. Detailed mapping and geological exploration in the mining area has made it possible to forecast possible locations for future seismic activity. In order to use the geology as a forecaster of mining-induced seismic events and the energy potential, two primary components are needed. The first component is a long history of recorded seismic events with accurately plotted locations. The second component is a high density of geologic data within the mining area. In this case, 181 events of 1.0ML or greater were recorded by the mine’s seismic network between January, 2009, and October, 2016. Within the mining area, 897 geophysical logs were analyzed from gas wells, 224 core holes were drilled and logged, and 1,031 fiberscope holes were examined by mine geologists. From this information, it was found that overburden thickness, sandstone thickness, and sandstone quality contributed greatly to seismic locations. After analyzing the data, a pattern became apparent indicating that the majority of seismic events occurred under specific conditions. Three maps were created using MineScape geological mapping software. MineScape deploys an interpolator known as FEM (finite element method) and is based on a series of gridded triangles to forecast the probability and magnitude of an event if a particular panel were to be mined. The forecast maps have shown accuracy of within 74%–89% when compared to the recorded 181 events that were 1.0 ML or greater when considering three major geological criteria of overburden thickness of 1900 feet or greater, 20 to 40 feet of sandstone within 50 feet of the Pocahontas number 3 seam, and a longwall caving height of 15 feet or less."

Jan 1, 2017

By Renn Oler

Corrosion can often cause significant strength reduction and failure of steel rockbolts, thus demanding continuous rehabilitation and posing challenges to underground mines in maintaining long term ground support. The mining industry has traditionally applied galvanized and epoxy coatings for protection of ground support and reinforcement in corrosive environments due to cost considerations. However, under a harsh and corrosive groundwater condition with extreme pH levels, failure of the existing coated rockbolts often results in failure and falls of the mine roof, especially in long-term mine drifts or entries. To prevent the roof falls induced by corrosive bolt failure, DSI developed a new polymer coating, called ?Obduro AP coating,? to combat harsh and corrosive ground conditions. The new polymer coating was tested in extreme conditions to identify weaknesses and was found to be capable of handling highly corrosive mine water solutions. This paper highlights the challenges faced by underground mines with corrosive bolt failure and shows that the DSI Omega BoltTM can withstand the most corrosive ground conditions when it is coated in the new, economic Obduro AP coating.

Jan 1, 2014

By Gautam Benerjee, Veera Reddy Boothukuri, Bhattacharjee Ram Madhav, Panigrahi Durga Charan

"India’s tryst with mechanized longwall coal mining started with the introduction of the first self-advancing powered support longwall (PSLW) face at Moonidih Colliery of Jharia Coalfield in 1978 and at Godavarikhani (GDK)7 Incline of Singareni Collieries Company Limited (SCCL) in 1983. During the last 37 years, about 30 longwall units in Coal India, Ltd., (CIL) and 10 longwall units in SCCL have been introduced with powered roof supports of varying capacity, ranging from 280 to 800 tonnes, in many mines in India under varying geological and geotechnical conditions. The majority of the longwall faces in India have been worked under relatively shallow cover (up to 200m), and significant strata control problems have been encountered due to poor caveability of the roof, inadequate capacity of the supports, a lack of knowledge on longwall caving mechanisms, less than adequate strata monitoring systems, and the non-availability of quality spare parts, etc. This has resulted in structural damage to supports and increased downtime of the equipment, thereby making longwall mining in India a case of technology failure. Energy demand for a developing country like India with a population of 1.2 billion is huge, and the thrust on increasing coal production continues. However, the share of coal production from underground mines in India continues to decline (current share is around 6%) because of absence of successful mass production technology in underground coal mining. Under this backdrop, a high-capacity longwall with state-of-the-art technology was introduced in 2014 at Adriyala Longwall Project (ALP) of SCCL for the first time in Indian Coal Mining Industry. The first longwall panel (LWP) has been completed successfully. This paper highlights the major geotechnical challenges encountered during development of the longwall gate roads due to the presence of two overlying clay bands, significant in-situ horizontal stresses and the experience of using rigid (welded) steel wire mesh with resin-anchored roof bolts. Efforts have been made to analyze longwall weighting and caving behavior, such as main and periodic weightings, the effect of front and side abutment pressures, and the behavior of gate roadway support systems under immediate friable weak roof with overlying massive sandstone."

Jan 1, 2017

By Syd Peng, Gamal Rashed

"Bumps in coal mines have been recognized as a major hazard for many years. These sudden violent failures around mine openings have compromised safety, ventilation and access to mine workings. Previous studies showed that the violence of coal specimen failure depends on both the interface friction and width-to-height (W/H) ratio of a coal specimen. The mode of failure for a uniaxially loaded coal specimen or a coal pillar is a combination of both shear failure along the interface and compressive failure in the coal. Unstable interface failures provide a sudden de-confinement to coal rib, thus triggering uns and compressive failure in the sidewalls. The compressive failure of a coal specimen or a coal pillar can be controlled by changing its W/H ratio. As the W/H ratio increases, the ultimate strength increases. With a proper combination of interface friction and the width-to-height (W/H) ratio of pillar or coal specimen, the mode of failure will change from sudden violent failure, which is brittle failure to non-violent failure, which is ductile failure. The main objective of this paper is to determine at what W/H ratio and interface friction the mode of failure changes from violent to non-violent. In this research, coal specimens of width-to-height ratio ranging from 1 to 10 were uniaxially tested under two interface frictions of 0.10 and 0.25. The results are presented and discussed.INTRODUCTIONCoal mine bumps are sudden, violent bursts of coal from a pillar or pillars or a block of coal, resulting in a section, the whole pillar, or the solid block of coal being thrown into an open entry. These bursts are accompanied by very loud noises (Peng, 2008). Several case histories in mining have long described coal pillars or coal faces failing violently with an accompanying ejection of debris and broken material into the working areas of the mines (Campoli et al., 1987; Osterwald, 1962; Peperakis, 1958; Garvey et al., 2013). Because of the catastrophic nature of these sudden failures, understanding the causes of coal mine bumps is essential to create a safe underground working environment. This phenomenon has motivated many ground control researchers to conduct extensive field investigations throughout the past century. Rashed and Peng (2014) compared the mechanical properties of two kinds of coal, one from bump and the other from non-bump-prone mines. They found that coal itself does not play any significant role in coal bumps and recommended that future research should focus more on the local variation of geological conditions such as the interface friction between pillar and roof and between pillar and floor."

Jan 1, 2015

By Sahendra Ram, Arnn Kr Singh, Dheeraj Kumar, Rajendra Singh

"Inherent existence of different rooms (openings) along the extraction line in a depillaring panel provides an easy path for the goaf to encroach the working area. Each of these openings in a mechanized depillaring (MD) operation along the extraction line is supported by the roof bolt-based breaker line support (RBBLS) to restrict the goaf encroachment. Different field studies by Council for Scientific and Industrial Research - Central Institute of Mining and Fuel Research (CSIR-CIMFR) found that the RBBLS works effectively during the depillaring under the shadow of stable surrounding ribs/fenders only. It is observed that, generally, these natural supports experience high value of induced stresses after a large amount of void creation inside the goaf. The induced stress creates spalling/loosening of the sides of the natural supports. Field studies also found that the positions of the RBBLS at the goaf edge need to be adjusted according to the depth of this spalling/ loosening. However, a systematic study in field for the correct positioning of the breaker line as per the spalling/loosening under different site conditions is difficult. Therefore, on the basis of the data and guidance provided by these field investigations, a detailed parametric investigation was conducted in the laboratory on simulated models for an effective design of RBBLS in a MD panel. FLAC3D is used for the simulation of the depillaring, and the available empirical formulations for Indian coalfields are used for subsequent calibration. An analysis of stress redistribution for different stages of the MD in simulated models showed the significance of the nature of overlying strata/induced stress for the RBBLS design. Discussing some results of field studies, this paper presents results of the laboratory investigations for an effective design of the RBBLS.INTRODUCTIONContinuous Miner (CM)-based mechanized depillaring (MD) is an important issue for Indian coalfields, where huge amounts of coal are locked up in standing pillars (Dixit and Mishra, 2010). Considerable variations in site conditions of these developed pillars bring a number of technical challenges into consideration during their final extraction. One of these challenges is goaf encroachment/overriding during caving of the competent roof strata. Goaf encroachment/overriding can effectively be controlled, mainly, by suitable design of natural supports (rib/snook/fender). However, there is a requirement of applied supports against the immediate roof as a considerable portion of this roof is exposed due to the presence of different openings along the line of extraction. These applied supports act as a fulcrum at the goaf edge between the working area and the goaf to facilitate the break out of the hanging roof inside the goaf. This is called breaker line support. An effective breaker line support is important for the efficiency of a depillaring operation. Generally, MD adopts roof bolt-based breaker line support (RBBLS) at the goaf edge (Singh, et al., 2014). For the first time in India, roof bolts were applied at the goaf edge as RBBLS in a CM-based MD (Leeming, 2003). In the beginning, three rows of roof bolts were installed as primary and secondary breaker lines support. On the basis of the observations of instrumented bolts, only two rows of roof bolts were used as secondary RBBLS (Ram, et al., 2014). Now, most of the MD operations in India are using only two rows of bolts as RBBLS (Table 1). However, the strata mechanics studies at different MD operations showed interesting characteristics resulting from this support (Ram, et al., 2015)."

Jan 1, 2016

By Chaojun Fan, Du Wenzhang, Sheng Li, Hong-Hong Shi

"Coal and gas outburst is an extremely complex dynamic disaster in coal mine production process which will damage casualties, equipment facilities and disorder the ventilation system by suddenly ejecting a great amount of coal and gas into roadway or working face. This paper analyzed the interaction among the three essential elements of coal and gas outburst dynamic system. A stress-seepage-damage coupling model was established which can be used to simulate the evolution of the dynamical system, and then the size scale of coal and gas outburst dynamical system was investigated. Results show that the dynamical system is consisted of three essential elements, coal-gas medium (material basis), geology dynamic environment (internal motivation) and mining disturbance (external motivation). On the case of C13 coal seam in Panyi mine, the dynamical system exists in the range of 8-12 m in front of advancing face. The size scale will be larger where there are large geologic structures. This research plays an important guiding role for developing measures of coal and gas outburst prediction and prevention. INTRODUCTIONCoal and gas outbursts are a complicated mine gas dynamic phenomenon that pose a serious threat to coal mine safety production. Since the first recorded coal and gas outburst occurring in Isaac coal mine of the Lule coal field in 1843, more than 40,000 outbursts have occurred in the world. China ranks first in outburst frequency and intensity. In recent 20 years, China on average increases 37 pairs of coal mines and more than 280 times outburst accidents every year (Yan, 2013). The coal and gas outburst occurred on Oct 20, 2004 in Daping Coal Mine, Zhengzhou Coal Group, caused serious gas explosions and ejected 1,894 tons of coal into the face, causing 148 fatalities. In recent years, despite implementation of numerous control measures, coal and gas outburst still occur frequently ash mining depth and mining intensity increase. The outburst mechanisms can be summarized in the following four aspects: the gas leading role hypothesis, the geostress leading role hypothesis, the chemical effect hypothesis, and combination hypothesis. The last hypothesis has won the acceptance of most scholars who consider that an outburst is the result of combined effect of stress, gas and coal (Yu, 1992).Numerous experimental measurements and numerical simulations were conducted to investigate the permeability and damage development process in coal seam. Sobczyk, et al (2011) carried out a laboratory research of the influence of sorption processes on gas stresses leading to coal and gas outbursts. Wang, et al (2013, 2015) conducted laboratory experiments to investigate the rapid decompression and desorption induced energetic failure in coal using a shock tube apparatus. Xu, et al (2006) developed a coupled gas flow and solid deformation numerical model and applied to simulate the coal and gas outbursts in underground coal mines using RFPA2D-Gasflow. An, et al (2013) and Xue (2014) analyzed major parameters and the effect of gas desorption on outburst initiation and established a model of gas migration and mechanical processes during excavation."

Jan 1, 2016

By Jesse Puller, Ken W. Mills, Owen Salisbury

"An underground coal mine located in New South Wales has a target coal seam located 160-180 m deep directly below a 16-20 m thick conglomerate unit that has been associated with significant periodic weighting events on the longwall face. As part of the investigations to better understand the causes of periodic weighting at the mine, inclinometers capable of measuring horizontal shear movements through the full section of the overburden strata were installed ahead of mining at two locations approximately 1 km apart above the centre of two longwall panels. These inclinometers were monitored as the longwall approached each site. This paper presents the details of the installation, the results of the inclinometer monitoring at both sites, and the insights that these measurements provide for overburden behaviour about longwall panels.Horizontal shear movements were observed to develop on shear horizons that correlate closely across the two sites suggesting a mechanism that is consistent across a large area of the mine. Shear movements were observed to develop on a single horizon near the top of the conglomerate strata that was mobilised almost immediately after initial formation of the longwall goaf at a distance of 425 m ahead of the longwall face. The direction of horizontal movement was consistent with the relief of the major principal horizontal stress. As the longwall face approached each inclinometer, other horizons within the upper part of the overburden strata begin to shear with the upper strata moving toward the approaching goaf more than the lower strata. Within the last 30 m of longwall approach, tilting of the strata associated with the increase in vertical subsidence toward the extracted goaf caused a change in the style of deformation with tilting and reverse shear offsets.INTRODUCTIONLongwall mining is recognised from subsidence monitoring, surface extensometer measurements, and various other observations to cause significant disturbance to the overburden strata directly above the extracted goaf of each longwall panel. Disturbance to the overburden strata beyond the limits of each longwall panel is not so well understood. Subsidence monitoring indicates that horizontal movements beyond the edges of the extracted longwall panel are generally greater in magnitude than vertical subsidence and horizontal movements may extend up to several kilometres from the edge of the panel in some circumstances (Reid 1998, Reid 2001, Hebblewhite et al 2000, Mills 2001, Mills 2014). The mechanics of how these movements are accommodated within the overburden strata is only poorly understood and there are few direct measurements."

Jan 1, 2015

By Enguang Zhu, Kangning Zhang, Yang Li

"Due to the use of outdated mining technology or room and pillar mining process in small coal mines, the coal recovery ratio is only 10% - 25%. In many regions of China: the damage area caused by the small coal mines amounted to nearly one hundred square kilometers. Therefore, special mining techniques must be taken to reclaim the wasted resource in disturbed coal areas. This paper focuses on the different mining methods by analyzing the longwall panel layout and abandoned gateroad (AG) distribution in in the abandoned area of Cui Jiazhai Coal Mine in northwestern China. On the basis of three-dimensional geological model, FLAC- 3D numerical simulation was employed. The abutment pressure distribution was simulated when the panel face passed through the disturbed areas. The proper angle of the inclined face was analyzed when the panel face passed through the abandoned gateroads. The results show that the head end of the face should be 13-20m ahead of the tail end. The pillars on both sides of abandoned gateroads had not been damaged at the same time, and no large-area stress concentration occurred above the main roof. Therefore, the coal reserves of disturbed areas can be successfully recovered by using underground longwall mining. INTRODUCTIONDuring the 70-90's, there were a lot of small coal mines in China. Due to their disordered mining, most of the small coal mines left a great many abandoned gateroads (defined as AG in this paper) and a large area of damage coal seam. In these type of coalfields, there exist many mining risk issues, including nonuniform stress in the overburden, flooding and hazardous gases accumulated in the gob. So how to lay out a longwall panel and successfully mining under this type of abandoned small mines is a big issue nowadays in China.As mentioned above, longwall panel is being performed in the damaged coal seams in order to increase recovery of coal reserves (Wang, 2009). However, the abandoned geteroads intersect to each other all around the area. So a series of production issues arose while the panel face is passing through these AG. Gang and Gong (2015) analyzed the roof stability and abutment pressure distribution during the face was passing those AG that were parallel and inclined to the faceline. Xie, et al. (2015) proposed the ground control mechanism by passing the AG in top-coal caving longwall mining. He recommended to stop the face advance until the roof is over, using high strength bolts and cable bolts, and grouting consolidation. This paper studies the different mining methods by analyzing the longwall panel layout and AG distribution in damage coal seams. Theoretical analysis and field observation were conducted to determine the overburden movement when the face was advancing under the AG. The pillar between face and parallel AG changes from elastic to plastic and eventually to the residual supporting status. All these three status was combined with the roof structure to establish the theoretical model to calculate the shield support capacity. Numerical modeling was employed to simulate the pillar stability and determine the abutment pressure distribution as the face inclined to the AG during longwall mining."

Jan 1, 2016

By Pengfei Wang, Guorui Feng

"The angle of break is the acute angle created by the coal seam bedding plane and caving line formed by roof strata movement after extraction of a longwall panel. It has a significant influence on stress redistribution both in the gob and abutment. Throughout numerical simulation investigations up to now, little attention has been paid to it, or an angle of break of 90° was used, which, however, is not realistic. This paper presents a detailed numerical modelling incorporating the angle of break against Zhenchengdi Coal Mine. The angle of break was obtained through cross-measure boreholes. Hoek-Brown constitutive model was used to simulate the rock masses. Double-yield constitutive model, which was best fitted by Salamon’s model, was used to simulate the gob. The results show that a “/ \ shape” shear failure zone develops around the gob. The shear failure in the floor along the panel edge is due to opposite shear of rock mass on two sides of the caving line, and the number of yielded zones within the gob floor close to the gob edge is smaller. According to the research, the entry was determined to be driven under the gob edge employing split-level longwall panel layout (SLPL). The other numerical simulation for SLPL shows that stress around the god-side entry is much smaller than pre-mining stress, and the area of intact rock mass at the elevating section is larger than conventional layout. Numerical modelling was then validated by field observation.INTRODUCTIONTo solve low recovery and ground control problems in longwall mining with top coal caving (LTCC) due to large gate pillar or chain pillar, gob-side entry approach is becoming increasingly popular (Nazimko, 1994; Li et al., 2016; Zhao, Wang, and Su, 2017). Gob-side entry is actually a combination of the gateroad, pillar, and gob, which is a typical panel layout with slender pillar or artificial pillar or wall. The abutment load has a profound impact on stability of the gate pillar, as well as the gob-side entry. Better estimates of abutment loading profiles will result in improved evaluations of design of pillar and gob-side entry (Larson and Lavoie, 2016)."

Jan 1, 2018