Search Documents

By Takashi Sasaoka, Hiroshi Takamoto, Akihiro Hamanaka, Pongpanya Phnthoudeth, Hideki Shimada, Jiro Oya

"Indonesia is the second largest coal exporter to Japan, accounting for about 30 Mt annually. They produced over 400 Mt in 2015, over 99% of which is from open-cut mines. However, the conditions of surface mining are becoming worse year by year: the stripping ratio is increasing, the economy is worsening, and the infrastructure for coal transportation from inland mining areas is not being maintained. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. In consideration of growing need, our research program is conducting a study on the potential for an underground coal mine in Indonesia. This research is being done through the roadway heading research program, which is looking into developing an underground coal mine from an open pit highwall. The greatest challenge for underground coal mine development in Indonesia is the maintaining the safety of the mine roadway during heading because the roof rock is exceptionally weaker. There is a potential for heading below mobile, unconsolidated soft sediment, and instead mining a deep area. This increases the likelihood for problems in the stability of the support system due to increasing ground pressure. The ground behavior around the roadway was measured using telltales, extensometers, and convergence measurements. Moreover, rock property tests were also conducted on exploration drilling cores. Based on the geological dates and monitoring data, a series of numerical analyses were conducted in order to assess support needs in the main roadway under different depths. Results of numerical analyses indicate that the current arch support design is effective when the mining depth is lower than 100m. However, if the mining depth is larger than 100m, the current arch support design should be changed to include the application of higher yield strength material, shorter spacing, etc. Moreover, bolting may also be useful if ground pressure is high locally. Based on a series of measurement data of ground and support behavior, a control criterion for main roadways under weak geological conditions is proposed in this paper."

Jan 1, 2017

By Dennis R. Dolinar

Roof falls, even of supported roof, still constitute a major hazard in underground mines. However, associated with any fall or instability is a pattern of roof movement. Therefore, the National Institute for Occupational Safety and Health, Pittsburgh Research Center, has been conducting research into the development of practical extensometer systems that can be used to measure this displacement and to determine if a roof fall may occur, thus increasing miner safety. For extensometers to be used in the detection of potential roof falls in coal mines, an understanding of the movement and displacement rates that will lead to roof failure is required. Because roof falls are unpredictable, it is often very difficult to obtain this information. Therefore, in a coal mine in the lower Kittanning seam in Pennsylvania, a room widening experiment was conducted to intentionally cause a roof fall while roof movement data was collected. In this experiment, two adjacent rooms 5.5 m (18 ft) wide supported with 1.5 m (5 ft) resin-grouted bolts and instrumented with extensometers were widened to 9 m (30 ft). In one of the rooms, 3.6 m (12 ft) cable bolts were installed as supplemental support. In the room with no additional support, a roof fall occurred 72 h after the room was widened. Much of the 3 cm (1.2 in) of movement in this room resulted from the instantaneous and transient response to mining with displacement rates up to 7.6 cm/d (3 in/d) being measured. This was followed by a steady state displacement phase with a rate of 0.43 cm/d (0.17 in/d). Just 12 h before the fall, movement deeper in the roof caused the rate to accelerate to 1.1 cm/d (0.44 in/d). The roof in the room with the supplemental cable support did not fall even though the total roof deformation was over 7.6 cm (3 in). Significant roof movements and strains in the cabled room were detected to a depth of 3 m (10 ft) while maximum cable loads were over 180 kN (40,000 lbf). Essentially, the roof was in postfailure with the cables maintaining the material, while roof stability was indicated by a steady state displacement rate of only 0.025 cm/d (0.01 in/d) at the end of the test.

Jan 1, 1997

By Mark F. Sindelar, Yi Luo, Hua Jiang, Michael T. Shook

"Convergence of roof and floor in underground mine openings is a common occurrence. This convergence not only adversely affects the ability of workers, equipment and supplies to travel through the mine, it also reduces the effectiveness of the mine ventilation system, which is essential for the dilution of methane gas and airborne respirable dust. While installing secondary standing supports to control floor and roof convergence, such supports, by nature, partially obstruct a portion of the airway. These added obstructions inhibit the ability of the ventilation system to operate as efficiently as it could by increasing the resistance in and reducing the cross-sectional area of the airway.This study introduces and demonstrates the benefits of The Eye CAN™ standing roof support, which controls floor and roof convergence and is less obstructive to air flow than conventional wooden cribs. Laboratory findings show that the normal resistance of a supported lined airway is reduced by using this new product from Burrell Mining Products, Inc., while providing the same roof support characteristics of an established product-The CAN®. Load vs. displacement curves generated from laboratory tests demonstrated that this new product behaves with the same roof support characteristics as others in The CAN product family. Ventilation data gathered from a simulated mine entry was then used for computational fluid dynamics (CFD) modeling. The CFD analysis showed an improvement with The Eye CAN versus other accepted forms of standing roof support.This proof-of-concept study suggests that, when using this new product made by Burrell Mining Products, Inc., not only will the convergence from the roof and floor be controlled, but airway resistance will also be reduced.INTRODUCTIONOne of the basic elements of underground mining is the necessity to support the mine roof. It is well-known that easier reserves have been mined so that today's underground mines present challenging conditions. Factors influencing roof support decisions include mine depth, mining method, overburden composition, and agency regulations. Mining engineers, therefore, have to balance three objectives: safety, engineering, and cost. While safety is obviously paramount, and engineering often complements safety, the cost effectiveness of any product, method, or device warrants additional consideration in today's harsh business climate. Avenues for adaptation and improvement are found at the intersection of the three objectives."

Jan 1, 2016

By Madan M. Singh

Currently longwall coal mining operations require at least 3 entries on both the headgate and tailgate ends because of ventilation and safety requirements. Driving of entries, however, is a slow and costly process. Often it is a bottleneck in longwall development. Single entry gateroads are permitted in Europe and commonly used there. This study entailed ascertaining the feasibility of using a single entry in the United States, without sacrificing safety. This design was conducted for an operating longwall mine in the Black Warrior coalfield in Alabama, An understanding of rock loads and consequent support requirements is prerequisite to the design and successful demonstration of the single entry system. Efforts in this regard were directed at determining center (packwall) support requirements for various single entry widths. Critical to the analysis is knowledge of the nature and extent of side abutment stresses. In collecting geological and geotechnical information relating to the stability of the single entry, Engineers International, Inc. engaged in the following: ? Examination and inspection of the single entry demonstration at the Sunnyside Mine in Utah. Severe ground conditions and unacceptable levels of entry closure were experienced there prior to the tailgate phase. Observations at the mine presented a clear perspective on possible ground control problems for future single entry designs. ? Reconnaissance inspection and classification of roof rock conditions. ? Detailed mapping of roof structure in the areas to be instrumented. ? Installation of convergence stations in the longwall headgate to monitor roof movement during mining. ? Measurement of side abutment stresses in a yield pillar in the area of the convergence measurements. ? Measurements of coal fracture distribution by the detail area method. ? Rock properties determinations of roof, coal, and floor rocks; samples obtained by core drilling. ? Determination of floor bearing capacity by in-situ testing.

Jan 1, 1982

By C. Babcock

This Bureau of Mines report considers some equations for mine pillar design from 1833 to the present. Most of the equations are of essentially the same kind, using pillar width to height relationships. The effects of end constraint and test volume size, that were implied in some of these early equations have received special emphasis in recent years. Experimental testing in the laboratory throughout the period given has been on prisms or cubes of coal or rock. Most of the present concepts have been known since about 1912. Wilson has recently emphasized the effect of end constraint in his confined core concept, but a number of other earlier relationships have indicated an awareness of the effects of constraint as well.

Jan 1, 1981

By Herryal Z. Anwar

In recent years, many both mining and civil engineering projects are developed in the area which may be categorized unstable, such as fractured and jointed rocks or "water sensitive rocks". For example, in underground coal mining, in which the floor strata normally consist of weak shale, the problem that may arise in roadway is floor heaving. In this case cement injection in borehole appears to be an economically effective method in order to make roadway more stable. This method may be also applied in the projects in which the constructions are laid on fractured and jointed rock. Nevertheless, the successful cement injection is much dependent on the water-cement ratio and the injection technique. This paper discusses the application of cement grouting to improve the ground stability in longwall mining, the laboratory experimentation of cement grouting and the method of floor injection.

Jan 1, 2000

By D. L. Price

This paper presents a method of measuring field power consumption of shearers and deriving specific energy consumption versus shearer haulage speed performance curves. A description of a computer program which simulates the cutting action of a shearer drum is presented. A comparison between the field specific energy curves and the computer simulation results is made. The simulation results compare well with the field data where all the coal seam is being cut by the shearer. The computer simulation results give hack-calculated field pick force cutting characteristics, which allow the performance of the shearer to be predicted for other operating conditions, e.g. effect of changes to pick lacing, effect of changing the drum rotational speed, allows the calculation of power requirements for a particular production rate.

Jan 1, 1992

By Thomas Lautsch

After a short description of geology and gateroad roof support technology in the German coalfields the development of roof bolting as primary roof support is presented. Based on geotechnical parameters, different strategies used for roof support at depths of 3,300-4,600 ft. are explained. Strict quality management and a strict monitoring program are part of the entry development. A number of recently finished developments are described such as the introduction of standardized bolts and accelerated resin systems. An outlook of future goals is presented. The paper concludes with a comparison of roof control systems at RAG's mines in the US and Germany.

Jan 1, 2000

By Khaled Morsy

Longwall mining is one of the most widely practiced underground coal mining method. The behavior of the longwall gob is very critical in the understanding of the complex ground response to longwall mining. In the limited data available, the values of gob moduli used in numerical modeling ranged from 1,000 psi to over 300,000 psi. Such a wide variation in moduli would greatly affect the results of the numerical analysis. A better understanding of the behavior of the gob will allow numerical models to be more accurate for simulating longwall mining conditions. In this study, a gob model based on the Terzaghi's model was incorporated into the comprehensive finite element package, ABAQUS, to simulate the loading behavior of longwali gob material. A case study was used to verify the proposed gob model.

Jan 1, 2002

By Syd Peng

"As the International Conference on Ground Control in Mining (ICGCM) enters its 35th year in 2015, it is time to look back and identify the areas that need to be emphasized and to look forward to see what areas need to be researched in the future. In the past three decades, ground control has made a tremendous advancement, and many case studies published in the 36 volumes of proceedings have demonstrated its important role in the daily mining operations. However, there is still plenty of room for improvements. This paper discusses the research needs in 12 subject areas, including mine geology, rock property, zones of disturbance in overburden, computer modeling, underground stress measurements, research method, roof bolting, coal pillars, failures, subsidence, shield supports, and coal bumps.INTRODUCTIONThe International Conference on Ground Control in Mining (ICGCM) was founded in 1981. Since then, 1,546 papers have been published in the 36 conference proceedings, including the three surface subsidence workshops held in the 1981, 1986, and 1992. All types of topical areas regarding mining, from geotechnical core loggings in the exploration phase through backfilling after mining to finally spoil piles stability on the surface, have been addressed. A review of these papers, and other related literature as well, indicate that ground control has developed to become an inseparable part of mine design and a problem-solving tool for safe production.After 34 years, it is time to look back and identify the areas that need to be emphasized and to look forward to see what areas need to be researched in the future. There is no doubt that the conference series has achieved the goal for which it was originally designed: to provide an annual forum for the exchange of information among the researchers, government regulators, equipment manufacturers, consultants, service providers, and—above all—mine operators. There have been many papers addressing the application of ground control techniques for successful mine design and safe production, and, without these papers, many projects would have failed. In fact, the conference emphasis on application types of papers may have steered too far toward the application side. A review of the conference papers shows that papers have been leaning mostly toward the applied side, leaving most, if not all, fundamental issues behind in nearly every topical area. This paper addresses research needs in 12 topical areas: mine geology, rock property, zones of disturbance in overburden, computer modeling, underground stress measurements, research method, roof bolting, coal pillars, failures, subsidence, shield supports, and coal bumps."

Jan 1, 2015

By Styles P.

To determine whether 130 felt earth tremors around Edwinstowe, Nottinghamshire U.K, which also experienced severe surface fissuring, were caused by coal extraction, a surface seismometer array was established around Thoresby Colliery. Over the next year, 785 microseismic events were detected. The spatio-temporal seismicity patterns are clearly associated with the commencement, continuing extraction and closure of faces. Of particular note are events which locate at the surface and appear to be related to the active fissuring. Events occur within days of commencement of production and cease when production finishes, with good correlation between face advance and hypocentral position. Naturally occurring microseismic events have also been detected up to 1 km ahead of active longwall faces in the Midlands using triaxial geophone packages grouted into the seam together with a surface seismometer in the top of the borehole. The quality of these data were very high and guided waves can clearly be seen with the dispersive characteristics associated with seam waves. In one experiment more than 2000 events were detected in only two days of monitoring even in a relatively noisy surface environment. This paper demonstrates how very accurate locations ( 5 10 metres) can be generated using three-component digital data from only one borehole. The surface seismometer and the borehole P-wave onset can give extra precision for the height of the event relative to the seam. The event distributions give a dynamic, three-dimensional image of the developing patterns of fracturing above, below and ahead of the longwall face with important implications for roof control, subsidence prediction and gas migration.

Jan 1, 1992

By Christopher Mark

The Analysis of Retreat Mining Pillar Stability (ARMPS) program has been used to evaluate room and pillar retreat mining layouts since it was first released in the mid 1990s. After the Crandall Canyon mine disaster focused attention on the importance of pillar design, ARMPS became an essential component in most Roof Control Plans developed by mine operators. In 2010, NIOSH released ARMPS version 6, which features a ?pressure arch? loading model for deep cover room and pillar mining. NIOSH has also provided general guidance for using ARMPS, including design criteria based on statistical analyses of an extensive case history data base. Many real-world retreat mining scenarios entail mining configurations that ARMPS does not directly address. Some of these situations that the MSHA Roof Control Division (RCD) has encountered in the course of its reviews of more than 100 ?complex and non-typical? plans are ? Unmined pillars are left at the mouth of a retreat panel that function as a ?composite barrier pillar? ? The floor is extracted on retreat, increasing the mining height ? More than one row of bleeder pillars is left in an adjacent, previously mined panel ? A retreat panel is located above or below a gob area in a previously mined seam ? Bleeder pillars are partially extracted on retreat RCD has developed solutions that allow these situations to be fitted into the ARMPS framework, and these are presented in this paper. Also discussed are some of the rules of thumb that have been developed for various input parameters, such as the treatment of inseam rock and slab cuts into solid coal.

Jan 1, 2011

By Christopher Mark

After the United States and Australia, South Africa has the largest. modern underground coal mining industry in the world. Historically, South Africa has been the cradle of many innovations in ground control, particularly in the area of pillar design. Today, South African mines are grappling with many of the same issues faced by their U.S. counterparts, including safety during pillar retreat operations, selecting the proper roof support, and maintaining long-term pillar stability. The author recently visited seven underground mines in the Mpumalanga, Free State, and KwaZulu-Natal provinces. Mining methods included longwall, room-and-pillar with continuous miners, and drill-and-blast. The mines represented a cross-section of geology and ground support practices. At each mine evaluations were made of the Coal Mine Roof Rating (CMRR), roof support practices, pillar design methods, and general ground control experience. The coal seams observed were generally thick (2-5 m), the depths of cover moderate (less than 200 m), and the roof rocks relatively strong (CMRR greater than 45). Unfortunately, the South African roof fall fatality rate is approximately three times greater than in U.S., perhaps in part because roof bolts seem to be more widely spaced in most South African mines. Roof bolting equipment was generally outdated, and the quality of bolt installation was a major concern. Pillar design, on the other hand, is quite advanced, and pillar failures are rare. Several novel partial pillaring techniques are employed, including "checkerboard" mining in which every other pillar is removed, 3-cut systems, and high-extraction mining where engineered final stumps are left by design. The paper also offers observations on ground control management techniques (including recently introduced Codes of Practice), the role of the mine inspectorate, and the status of the research community.

Jan 1, 1999

By Stephen C. Tadolini, Robert Hawker, Peter Mills, Colin Grubb, Tom Meikle

"In unfavorable strata conditions, it is often necessary to install additional long tendon support as part of a primary support cycle. Although these support systems provide the required additional stability to the roadway installation does have a significant effect on the rate of development. To overcome the slow cure time of Portland cement-type grouts, the use of two component resin systems, such as polyurethanes and urea silicates, have become favorable. However, concerns over low modulus and creep properties has led to the development of a two-component grouting medium that displays the properties of traditional cable grouting materials with the rapid reaction times of pumpable resin systems. This paper describes product testing, application, surface trials, underground trials, and full-scale applications of the Tekthix System in a dynamic underground environment. INTRODUCTION Single-component cement grouts have been used to anchor long tendon supports for many years. They range from high- to low-slump Portland cement and can be slow-setting to fast-setting grouts. However, current cement grouting systems, which includes the grout and equipment, have some disadvantages: 1. Low-slump grouts require pumps that can handle a thick, high-viscosity grout, so choice of pumps is limited. 2. Pumping distance is limited with current cable bolt grout pumps; operators often tend to add water to allow pumping long distance, which adversely impacts the quality and strength of the material. 3. Fast-setting grouts tend to cause issues with pump and line blockages due to the reduced working life of these single-component materials."

Jan 1, 2017

By Vincent A. Scovazzo

"The most significant study on the effects of longwall mining on gas and oil well integrity was completed by a consortium of coal and shale gas industry participants. A field study was conducted in 2013 and 2014 and is referred to by its location on Well Pad NV-35. The experiment site was located at the CONSOL Enlow Fork Mine in Washington County, Pennsylvania.The experiment was completed to verify John T. Boyd Company (BOYD) calculations and studies completed under contract by for the Pennsylvania Department of Environmental Protection Gas Well Pillar Study Update. The findings of the original study were presented by BOYD at the 32nd Conference, while numerical analysis of the Well Pad NV-35 field study was presented by Dr. Su at the 35th Conference.This paper addresses the findings of the experiment and how it confirmed the conclusions of the original study.INTRODUCTIONA field study was conducted in 2013 and 2014 by a consortium of coal and shale gas industry members to test the effects of longwall-induced ground movement on the stability and integrity of wells drilled through a gateroad abutment pillar. The project was initiated to test initial John T. Boyd Company (BOYD) findings of the Gas Well Pillar Study Update (Scovazzo and Moran, 2014), completed for Pennsylvania Department of Environmental Protection, Bureau of Oil and Gas Management (PDEP). Background and initial findings on this project were presented at the 32nd Conference (Scovazzo and Moran, 2012). The field work and numerical analysis were spearheaded by CONSOL Energy, Inc. (CONSOL) with participation by Chevron, EQT, Noble Energy, Range Resources, Marcellus Shale Coalition, and the Pennsylvania Coal Alliance.Dr. Wen H. Su of CONSOL was the leader of the field experiment with input from the participants. Dr. Su also completed numerical analysis of the results and model casing deformation. Analytical results were presented by Dr. Su at the 35th Conference (Su, 2017)."

Jan 1, 2018

By David Newman

The latest version of the Surface Deformation Prediction Software (SDPS) package is presented through its application to a number of case studies. The package now exploits all the benefits of the Microsoft Windows platform and has a direct interface to CAD software, thus facilitating input and output. Also, the package features advanced calibration routines to handle predictions over specific regions. The case studies presented highlight the features and capabilities of the new package.

Jan 1, 2001

By Bruce K. Hebblewhite

This paper provides an overview of the international ?state of the art? with respect to underground coal mining methods used in seams of thickness greater than 4.5 m, through a review of a selection of high performing thick seam mining operations around the world?both Single Pass Longwall (SPL) and Longwall Top Coal Caving (LTCC). The paper discusses the recent operational experiences from these selected faces, together with the ground control issues faced, and identifies some of the major, inherent geotechnical factors that can influence the mining method selection, design criteria, and ultimate performance, from both an operational and safety perspective. It is clear that both of these methods are developing quickly? not only from an operational and equipment perspective, but also from the understanding of critical geotechnical criteria. There is an increasing role for both methods in thick seam environments, although the higher SPL faces will only be successful in the near to mid-term under benign geotechnical environments. Regardless of the method, a thorough understanding of the critical geotechnical factors is a key to successful implementation of either method.

Jan 1, 2013

The objective of extensive underground experimentation on three longwall coal faces was to improve the stability of mechanised longwall faces through investigation of the relations between support resistance and convergence and resultant deformation of roof and face strata. In particular the influence of high setting and yield pressures on several strata and support parameters was studied in great depth. Increased setting pressures resulting in an increase in setting load densities from 0.15 MN/m2 to O.45 MN/m2 were shown to reduce convergence, face spalling roof flaking, lateral movement of roof and floor, extrusion of the face wall and progressive failure of the coal wall ahead of the face. This was shown to result mainly from the change in roof strata deformation from a wedge shaped compression zone with tension at the face edge to an even beam shaped compression zone over the face area. Debris thickness above the support canopy and below the base was observed to be the one of the most variable parameters which influenced the support characteristics particularly the rate of load acceptance by supports and the roof to floor convergence. A setting load density of 0.4 MN/m2 to 0.5 MN/m2 was found to be optimum under soft to moderately strong sandstone roofs. The authors demonstrated that use of guaranteed set valves with powered supports contribute to good strata control, reduce face down-time and increase face productivity.

Jan 1, 1984

By B. Tulu, D. Gearhart

A comprehensive monitoring program was conducted to measure the rock mass displacements, support response, and stress changes at a longwall tailgate entry in West Virginia. Monitoring was initiated a few days after development of the gateroad entries and continued during passage of the longwall panels on both sides of the entry. Monitoring included overcore stress measurements of the initial stress within the rock mass, changes in cable bolt loading, standing support pressure, roof deformation, rib deformation, stress changes in the coal pillar, and changes in the full three-dimensional stress tensor within the rock mass at six locations around the monitoring site. During the passage of the first longwall, stress measurements in the rock and coal detected minor changes in loading, while minor changes were detected in roof deformation. As a result of the relatively favorable stress and geological conditions, the support systems did not experience severe loading or rock deformation until the second panel approached within 30–50 ft of the instrumented locations. After reaching the peak loading at about two to three inches of roof sag, the cable bolts started to unload, and the load was transferred to the standing supports. The standing support system was able to maintain an adequate opening inby the shields to provide ventilation to the first crosscut inby the face, as designed. The results were used to calibrate modeled cable bolt response to field data and to validate numerical modeling procedures that have been developed to evaluate entry support systems. It is concluded that the support system was more than adequate to control the roof of the tailgate up to the longwall face location. The monitoring results have provided valuable data for the development and validation of support design strategies for longwall tailgate entries.

Jan 1, 2017

By David K. Ingram

The objective of this U.S. Bureau of Mines (USBM) investigation was to characterize overburden response due to longwall mining. Subsurface strata and surface deformations were monitored at two sites in southeastern Ohio. Site A included two adjacent longwall panels. Site B consisted of one longwall panel. Both sites had similar mine geometries and overburden thicknesses. The major difference between the two sites was the rock strata within the overburden. Multipoint borehole extensometers (MPBX) were employed to measure subsurface displacements. Survey monuments were installed above the centerline and profile of each panel to measure surface deformations. Subsidence of the surface was observed before and after movement was detected in the MPBX units. Initial and final displacement of the MPBX units occurred at the same time at both sites. No deformation was detected outside the panel area. The development of overburden deformation was different over each panel. The final subsurface failure characteristics also varied between panels.

Jan 1, 1994