Search Documents

By Paul D. Tomlingson

Editor's note: This is the first of two articles on maintenance. Part two, "Effective maintenance downsizing techniques," will appear in the October issue of MINING ENGINEERING. Most mine managers are aware that the cost of maintenance rarely goes down unless work is done less often and with fewer people. Fewer people translates into downsizing and seldom means making maintenance more efficient. Even so, mines that have struggled unsuccessfully to improve maintenance and are now pressed to reduce maintenance costs may opt for downsizing. On the other hand, mines with an immediate need to reduce costs may be forced to downsize because they cannot wait for needed improvements to take effect. This can be bad news for maintenance. In any case, the mine must downsize correctly to ensure effective maintenance is sustained.

Jan 1, 1994

By D. Leppert

Mr. Garrett brings up several interesting points with respect to the proposed API specification for "nontreated bentonite." However, although not explicitly stated, these specifications are being written based strictly on bentonites from the Wyoming/South Dakota area. Other sodium bentonites may be suitable for use as drill mud but will be unacceptable since the specifications are designed for Wyoming bentonites. Regardless of the API's intent that its specifications are intended only as guidelines, they are generally adhered to on an international basis and, for practical purposes, might as well be chiseled in stone. Estes (1986) notes that the quality of bentonite available from Wyoming producers has steadily declined since the early 1960's. The plastic viscosity: yield point (PV:YP) ratio was included in the current API 13A specification primarily to prevent excessive polymer treatment of lower quality bentonites to make drill mud. However, with development of polymers designed to control YP, this specification cannot ensure that only high-quality bentonites are used for drill mud. Nor will the new specifications for untreated bentonites. Other sodium bentonites are available. Bentonite produced in southeast Oregon demonstrates superior performance characteristics without addition of polymer or other chemicals. However, the exceptionally high purity of these deposits leads to a relatively high YP:PV ratio since the naturally high YP probably results from the higher purity and smaller particle size of this bentonite (Rath, 1986 and personal communication). These bentonites typically have a smectite component exceeding 90% (Rath, 1985), compared with 70% to 75% smectite for typical Wyoming bentonites, as determined by X¬ray diffraction and tests for colloid content. As evident from the accompanying table, the untreated Oregon bentonite has excellent rheological properties, though different from Wyoming bentonites due to the high purity. Additionally, this bentonite reacts well with polymers typically used in the oil industry, making it eminently suitable for use in a low-solids mud system. The extremely low grit content, less that 0.5% on a 75 mm (200-mesh) wet sieve, greatly exceeds the standards set for Wyoming bentonite. Optimum rheological properties are obtained at a higher moisture content than Wyoming bentonites. At 10% moisture, API 13A maximum, the clay is overdried, again reflecting the high smectite content. In summary, the specifications proposed by the API Task Group will ensure that only Wyoming producers can supply "nontreated" bentonite to the oilfield since specifications are

Jan 1, 1989

By Christy Z. Lueders

Introduction More and more women engineers are joining the traditionally male mining industry. Are they successful? Do they encounter special problems? How do men in mining respond? How can the mining industry effectively use its female resources? What contributes to the success of a woman in mining? What can male engineers do to ease the entry of female professionals into the workforce? An STM survey conducted last spring provided some answers to these questions. All BS graduates in mining, mineral engineering, and extractive metallurgy from 1960-1979 were surveyed. Nearly 60% of the female graduates, from 17 universities, completed questionnaires. The women were asked why they chose mining, how they relate to predominantly male co-workers, what job skills they have gained, and what areas of work they most enjoy. They were also asked how problems of a two-career family are solved. Data were gathered on salaries, titles, specialties, and products handled. Respondents, assured of confidentiality, are identified only by title. Many male mining executives were also questioned for their advice to women in mining. Profile of the Survey Participant The "typical" female mining engineer works with coal, is employed by an operating company, feels she works very hard to prove her abilities, does not want to be treated as an anomaly, and someday wants to be an independent consultant. Of the respondents, 44% listed coal as the most familiar product, 12% said copper, and the rest listed products from industrial chemicals to oil. Titles varied widely but women managers are rarely found. However, the majority of the survey population graduated after 1976 and thus lacks substantial experience. Of 102 female graduates, only 25 graduated before 1977. Since then, there has been a steady increase. The American Association of Engineering Societies reported that in 1980 more than 100 degrees were awarded to women in minerals engineering. Education Highly Valued Twenty-two percent of the women surveyed had graduate degrees, 38% planned further education, and 12% listed a PhD as their goal. The majority of graduate degrees are in technical fields. There were only two MBAs. Five women intended to pursue law degrees, and one woman, with a mining engineering degree and an MBA, is a part-time law student. Along with advanced education, the women agree that production experience is needed for career advancement. However, only 28% of the women have worked in production. Many women, especially younger grads, commented that these are the toughest jobs to get. This is a universal complaint, from males as well as females, though women seem to encounter more opposition. Several women mentioned they were small or slight of build and managers tended to shy away from hiring them for production jobs. Two-Career Marriages The most difficult problem for two-career couples is relocation. Whose career takes priority? Fifty percent of the women said transfers or offers would be examined on a case-by-case basis, weighing pros and cons for both parties. The husband's career took priority with 47% of the women; their own careers, with 3%. These statistics conflict with comments from two employee relations managers. Both said most female engineers they've encountered are married to men who follow their wives' careers. Seventy per cent of the married respondents said their husbands were also engineers. Four said their husbands were engineers at the same company. Some male and female engineers met on the job; others joined the company as a "package deal." Both partners being engineers can ease relocation problems, since an area or company offering one spouse a job can often provide a spot for the other. A company may benefit by getting two new hires for the relocation costs of one. Most companies contacted have policies that allow married couples to work at the same division, but discouraged them from working in the same department. With 40% of today's marriages ending in divorce, one risk is that one or both parties may quit. One personnel executive said there were several couples, each spouse in a different discipline, who were work¬ing out very well at his division. However, he recognized the potential for problems if, for instance, one gets promoted and the other doesn't, or salary increases are unequal. The personnel executive said he has actively recruited married couples, and would again, were each person competent.

Jan 10, 1981

By Bruce Cavender

Historically, the processing function has been regarded as efficiently managed as long as production costs were kept low, recovery was adequate and sufficient plant capacity was avail-able. In this paradigm, processing is viewed as capable of making only a limited contribution to a company?s competitive advantage. However, the processing function can provide a primary vehicle for building critical competitive capabilities. Processing organizations should be encouraged to become so accomplished they generate new opportunities for other functional groups and thereby influence a company?s overall strategy. This requires a deep shift in processing?s role, in its self-image and in the expectations of it held by managers in other functions. Specific plant improvement techniques ? total productive maintenance (TPM), loss control, etc. ? should be viewed primarily as means for building strategically valuable processing capabilities. Different improvement strategies create different kinds of capabilities and present new strategic options. Broadly speaking, a mineral-producing company seeks competitive advantage through two principal activities: the development of new mineral production and reserves and the optimization of existing operations. These lead to increases in ore reserves, production levels and cash flows that are manifested in increased profitability and, hopefully, increases in the price of the firm?s stock. The profitability of a minerals company is a function of the overall profitability of the industry sector in which the company participates and the firm?s competitive position within that sector relative to those of its competitors. Competitive advantage within the industry comes from two sources: the ability to maintain lower prices than competitors for the same product (cost leadership), or from the sale of products with unique properties that justify higher prices (product differentiation; Porter, 1980). Most mineral companies produce fungible commodities that are sold to anonymous customers, and sustainable cost advantage is the only long-run strategy available to these companies to enhance profitability.

Jan 1, 2008

By S. K. Oraee

Managers always look for systems with minimum hazards. The hazards create problems for performance of projects. The largest and most important hazards of working underground mine can be related to health, safety and environmental, because if one of these sectors be in hazard, maybe lead to close mine. Failure mode and effects analysis (FMEA) is a widely used quality improvement tool to identify the potential failure modes for measuring reliability of a product or a process. FMEA is performed by developing a risk priority number (RPN), which is the product of severity, occurrence, and detection ratings. On the other hand, with regard to uncertainty in the decision-making, fuzzy theory will be able to model this uncertainty. Fuzzy FMEA provides a tool that can work in a better way with vague concepts and without sufficient information than conventional FMEA. This article by using Fuzzy FMEA and based on HSE criteria evaluate hazards of Parvade No. 1 Mine in Tabas Coal Mine. The results demonstrate the most hazardous parameter is rock burst in this mine.

Jan 1, 2011

By Neville Slade, Doug Shumway, Dayan Anderson, Joe Siefke, Curtis James

The Mojave Desert is a particularly fragile ecosystem that faces several significant impacts. These include rapid housing development, overdrafted water supplies and loss of wildlife habitat — all a result of mining, industrial activity and urban sprawl. During the past three years, a diverse group of educators, natural resource managers and business leaders was assembled under the auspices of a local community college. This group’s goal was to provide unique natural resource education opportunities for the region.

Jan 1, 2005

By Desiree Willis

Disc cutters have determined excavation rates of rock tunneling projects for more than 50 years. First developed in 1956 by James S. Robbins, disc cutters (then 279 mm or 11 in. in diameter) were used to bore limestone of 190 MPa (27,500 psi) unconfined compressive strength (UCS) and were loaded with 7.12 t (15,700 lbs) each. Modern cutters have reached up to 508 mm (20 in.) in diameter and are typically loaded with up to 31.7 t (70,000 lb) to economically bore through the hardest of rock up to plus 400 MPa (60,000 psi) UCS. New developments, such as larger cutter diameters, are geared to increasing the bearing capacity and wear life of the cutting structure. This, in turn, increases cutter life, cutter load and cutter penetration. Disc cutters have also been re-designed on a small scale for use in hard-rock utility installations. Additional variables also affect the three factors, including cutter spacing on the cutterhead, cutterhead diameter and cutter materials.

Jan 1, 2007

Diesel Particulate Matter (DPM) issues are very high profile currently in both Australian coal and metal mines and Australian states are generally moving to acknowledge and to broadly follow US 2008 final metal/non metal mine regulation limits of 0.2 mg/m3 submicron particulate matter, 0.16 mg/m3 total carbon particulate and 0.1 mg/m3 elemental carbon particulate. The real time DPM monitor is being developed on the base of the successful Personal Dust Monitor (PDM) unit. The objectives of recently completed Australian Coal Association Research Program (ACARP) study has been to finalize the design of a DPM unit, to undertake comprehensive and internationally recognized laboratory testing to evaluate the new design and to undertake an underground series of tests to establish the robustness and reliability of the new approach. Under the project Thermo Fisher Scientific has undertaken structural changes to the PDM to convert it to a DPM real time monitoring underground instrument, the D-PDM. The Pennsylvania Pittsburgh Research Laboratories of NIOSH (the group that originally contracted for the PDM development) has undertaken laboratory ?calibration or verification? testing. A phase of Australian mine robustness and engineering testing has been undertaken to ensure the instrument can effectively assist mine management to handle this health issue. Tests have been undertaken at points of expected high atmospheric DPM such as during Longwall face moves, Development RAM car, Eimco and PJB usages. The paper discusses how the monitors have performed within the underground mine environment in evaluating DPM during the various phases of the production cycle. They have closely examined the influence of aspects of the mine ventilation system. Results have been compared to alternative industry pollutant measuring approaches. The outcome of the project gives the industry access to an enhanced tool for understanding the mine atmosphere in the presence of DPM. Real time DPM monitoring will allow the industry to pin-point high exposure zones such as those encountered in coal longwall face moves where various vehicles work or in areas of constrained or difficult ventilation. Identifying of high DPM concentration zones allows efficient modification of work practices to reduce underground miners? exposure. Some outcomes of the ACARP project in this area will be discussed.

Jan 1, 2009

By K. N. Panigrahi

India bestowed with 6000km of the coastal belt, contains some of the richest and largest placer deposits with a mixture of heavy minerals like ilmenite, rutile, leucoxene, zircon, monazite, sillimanite and garnet. Each of the minerals is having economic value due to its inherent characteristics for industrial use in fields of paints, metallurgy, refractory, abrasive and so on. The reserves of titanium bearing minerals (ilmenite, leucoxene, and rutile) in the country is around 378 million tonnes. More than 90% of the titanium based minerals produced worldwide are utilised for making value added products in the pigment industries. Approximately 8 million tonnes of monazite reserves are available in the country from which several rare earth elements like cerium, neodymium, lanthanum, yttrium etc. can be extracted for use in several industries. The country contains a deposit of about 20 million tonnes of zircon, which is used in foundries, refractories, ceramics and chemicals. India has a reserve of 107 million tonnes of garnet and 131 million tonnes of sillimanite required for the abrasive and refractory industries respectively. Keeping in view the multifarious uses, the beach sand minerals are being exploited to have the economic growth of the nation. Although the process adopted for the separations are simple, the equipment involved are specially designed because of the nature of the material of construction. Starting from the spirals to magnetic separators, all equipments are manufactured outside India, which is not only costly, but the availability also takes much time for fulfilling the import formalities. Unlike open cast mining, beach sand mining is a environment friendly mining because dredging is implemented to cut and pump the loose sand through a slurry pump causing less damage to the surface topography as both mining and backfilling takes place simultaneously. Therefore all out efforts are made to explore the beach sand placer deposits in an economic manner to emerge as a leader in the global mineral industries.

Jan 1, 2005

By Steve Kral

In a lagging economy where profits are tight, businesses cut costs. No revelation there. The mining industry, though, has always looked for ways to reduce production costs — no matter the state of the economy or commodity prices. The fact is, when planning a new mine or the expansion of an existing one, mining companies gamble that commodity prices will be reasonably high when a project comes onstream. It takes millions of dollars and several years to bring a mine into operation. And a lot can happen economically between the time management gives the go-ahead for a new project and its completion.

Jan 1, 2002

By H. Takamoto, M. Ichinose

"The basic objectives of mine roadways are to provide sufficient cross sections in order to meet the needs of accommodation of equipment, transport, personnel travel and ventilation. However, many roadways become damaged to the extent of needing maintenance, generally dinting, and in some cases requiring re-ripping. The damaging of a roadway is a result of several factors including geological properties of surrounding strata, method of roadway formation, support systems and so on. Among these factors, strata conditions play important effects on the stability of roadways and other mining activities. Weak rocks cause excessive roadway closures, and water softens some rocks and worsens the closure problem. In Indonesia, over 250 Mt of coal is now produced from almost surface mines. In the near future, some coal must be mined from underground. Unfortunately, the mechanical properties of coal measures rocks are not so good to open underground mines. In this paper, a scientific discussion on the effect of water on the stability of roadways is given on the basis of results obtained by means of in-situ investigation and laboratory tests both in Japan and Indonesia."

Jan 1, 2011

By D. S. Kieffer

Ground characterized by hard boulders embedded in soft matrix represents one of the most challenging conditions for TBMs, as the cutterhead must cope with the non-optimal conditions of cutting hard blocks while simultaneously excavating through soft, soil-like matrix material. Dowden and Robinson (2001) and Hunt and Mazhar (2004) summarize several case histories relating to the problems of advancing a TBM through boulder-laden ground and provide guidance with respect to appropriate site investigations and baselining strategies. Some rock types constituting boulder-laden ground include: ?Sedimentary Rocks?cemented alluvial channel deposits, colluvium/talus, landslide debris, and glacial till. ?Igneous Rocks?agglomerates, lahars, and pyroclastic deposits. ?Metamorphic Rocks?tectonic mélange and cataclastic fault zones. ?Decomposed Rocks?corestone bearing saprolites. Disc cutters are commonly utilized to cut the hardblocks; however, as compared to the understanding of disc cutter behavior in hard continuous rocks, little is known regarding fundamental cutting mechanisms in highly heterogeneous bouldery ground conditions. To advance this understanding, a suite of full scale tests have been performed using a linear cutting machine at the Colorado School of Mines (CSM). This paper summarizes the observed cutting mechanisms and their practical implications for TBM excavations through boulder-laden ground.

Jan 1, 2008

By T. Burchett, F. Stanley, K. McGough, G. Luttrell

The vast majority of U.S. coal preparation plants utilize screen-bowl centrifuges to dewater their fine clean coal products. In light of this popularity, researchers at Virginia Tech have engaged in a variety of laboratory and industrial field test programs to develop technological enhancements that have the potential to further improve the performance of this important solid-liquid separation process. These enhancements, which include simple design modifications and new reagent packages, have been shown to significantly improve solids recovery and reduce product moisture in several experimental trials.

Jan 1, 2006

For the past four years, the Department of Mining Engineering at the University of Kentucky has conducted a validation study of the CFD Fluent code, by comparing its results against mining-related benchmark experimental data provided by NIOSH?s Pittsburgh Research Laboratory. This particular study is dedicated to the effect of machine-mounted dust scrubbers on the performance of face ventilation systems using extended-cut mining with a blowing curtain.

Jan 1, 2009

The structural design of a mine haul road involves the determination of cover thickness requirements above the in-situ or sub-grade material. The specification of these layerworks is a critical component in the overall road design process. Poor design often leads to premature failure of the road, safety is often compromised and productivity and equipment service-life will certainly decrease. Historically, the California Bearing Ratio (CBR) cover-curve design method has been widely applied to the structural design of mine haul roads. More recently, established mechanistic design principles have superceded the CBR approach to haul road design, using a multi-layer model to represent the various road structural layers. The structural design and associated layer thickness requirements are then determined following a maximum strain criterion. This paper develops a case-study evaluation of the CBR cover-curve and mechanistic design methodologies and through a comparative analysis of layerworks and materials, highlights how improved structural design can be achieved mechanistically.

Jan 1, 2011

By F. H. Seymour

Central to Newmont Gold's Mine planning system is the ability to interactively perform cut and fill operations on topographic contours and to accurately evaluate grades and tonnages within contour outlines using polygon set manipulation routines. This paper develops the applied geometry concepts that underlie these routines. Included are representation of volumes with contours, point in polygon test, block proportion in polygon calculation, polygon area and centroid calculation, and intersection, union, and complement between polygon sets.

Jan 1, 1990

By Rudolf E. Greuer

It is undisputed that an interaction between mine fires and mine ventilation systems exists. The ventilation carries the poisonous and sometimes explosive combustion products, which constitute the greatest danger of mine fires, through the mine and it provides the oxygen on which the intensity of the fire depends. The fire, on the other hand, can produce considerable ventilation disturbances which make it difficult to predict the path along which the combustion products travel. The opinions, how serious a threat such fire generated ventilation disturbances are, vary. Where shallow deposits are mined and brisk ventilation currents are used, it is frequently felt that these disturbances are of no serious concern. Where mine workings extend over larger elevation differences and where such disturbances have been encountered and been the cause of some larger disasters, their assessment is an integral part of all fire emergency plans. The author felt that the potential of digital computers for the design of ventilation emergency plans, contrary to their acceptance for conventional ventilation planning for more than two decades, is not yet fully utilized. He designed a program for the simulation of ventilation systems under emergency conditions in particular fires. This was part of work completed for a contract with the U.S. Bureau of Mines ( Open File Report OFR 115(1)-78)

Jan 1, 1980

By George L. Wilhelm

Timber support of mine openings continues to be an effective system for ground support, due to its avail¬ability, flexibility, and ease of installation. Timber support of mine openings as a primary method to support loose rock has been replaced to a large extent by rockbolting and by filling systems. How¬ever, the many designs of square-set timber and varia¬tions of crib and stull support that have been developed to suit many stope configurations have proven reliable over many years of application. Integrated in modern excavation and stoping methods, timber remains an im¬portant ground support material for today's mines. ADVANTAGES AND DISADVANTAGES OF TIMBER SYSTEMS Timber, when used as a part of the total support system, is recognized for its unique support properties. More than a cover to prevent minor falls of ground, timber systems have been carefully designed to provide adequate support with sufficient compressive qualities to achieve a safe working environment in extremely diffi¬cult ground conditions. In some cases, a timber support method is designed to yield while retaining its protec¬tive support qualities. Little or no initial investment in equipment or plant is required for incorporating timber into the mining support system. Low cost cutoff saws and portable chain saws are sufficient equipment for effective use of dimen¬sioned (sawed) or round (stull) timber support. Until recently, small sawmills of various complexity were com¬mon at mine surface plants. Sawmills at the mine sites have generally been replaced by timber vendors' mills. Suppliers have been able to use efficient cutting and lumber handling methods to reduce the cost of mine timbers. Most suppliers will package dimensioned mine timber into bundles that are suitable for handling down mine shafts and on level conveyances. The principal disadvantage of timber as a support method is higher material cost and labor cost associated with its labor-intensive installation. Furthermore, stand¬ing timber reserves of mine quality wood are in short supply in some areas, and heavy competition exists for alternative uses of the timber supplies. Vendors are reluctant to supply large cross section dimension tim¬bers relatively free of defects. Some mine operations require 4.8-m (16-ft) lengths of firm timber over 0.09 m2 (144 sq in.) in section and these are difficult to obtain in large quantities. APPLICATION OF TIMBER FOR MINE SUPPORTS Timber used in mine support has been cut from many species of trees. A firm hardwood with physical properties similar to western Douglas fir has been pre¬ferred in the US. Other harder and softer woods, how¬ever, have been used when readily available or where the specific strength or crushing quality of the wood is a desired specification of the support system design. Hard¬ wood, commonly oak, has been used where maximum crushing resistance is required. Mahogany and fir are widely used for shaft guide timber. Normally, timber is used with its core axis parallel to the long axis of the timber dimension. However, in some cases, it is placed normal to its core in a "butt" log position, so as to provide maximum resistance to abrasion of the ore passage adjacent to the cut end of the block. By selective placement of timber block¬ing, controlled resistance to ground closure can be achieved which will prevent early failure of primary sup¬port members of the timber structure. Timber is widely used in modern mining operations as a construction member for chute-lip support. These designs are tailored to each operation to conform to the dimensions of the haulage equipment being used. As a construction material, wood requires none of the spe¬cial equipment necessary for placement of concrete or steel support. Placement of these alternate support ma¬terials requires carefully dimensioned and engineered excavation for their installation. Wood can be easily sawed to fit on location. The successful use of timber in heavy ground de¬pends on the careful and accurate placement of block¬ing and bracing to achieve the controlled yielding re¬sistance needed to support the mine opening. Similarly, frequency, size, and placement of top and bottom block¬ing stulls in flat-bedded deposits are carefully determined to provide adequate support at the mining face. Con¬trolled caving through failure of the stulls may be required as the scope retreats from the earlier mined-out sections. The support program must achieve both of these dimensionless qualities by specification of stull frequency and size. The utility of the square set-system of ground sup¬port and timber support is described in Chap. 2, re¬printed from US Bureau of Mines Information Circular 6691. Four examples of effective use of timber for support of stoping and other mine openings are pre¬sented in other chapters in this section. The Gilman mine's use of Mitchell slice stoping described in Chap. 3 is an early modification of the square-set mining system. This application proved reli¬able for heavy ground and overcame some of the dis¬advantages of conventional square-set timber. Chap. 4 describes the Burgin mine's use of timber with other reinforcement material. This combination of materials achieved high strength and control with yielding com¬ponent members necessary for heavy, squeezing ground. Chap. 5 describes the Bunker Hill mine's use of square¬set timber in a new configuration that provides an effi¬cient and safe support for stoping using small load¬haul-dump (LHD) mobile equipment. Chap. 6 describes some considerations in placing the widely used stull in bedded ore deposits. Finally, in Chap. 7, cost calcula¬tions for

Jan 1, 1982

By J. C. Stankus

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult because a slope will transverse through many different types of strata. Over the past three years, Keystone Mining Services, LLC, an affiliate company of Jennmar Corporation, has developed a new methodology designated the ?Stress, Geologic, and Support Design System (SGSsm)?. This patent pending method analyzes the stress, geology, and support design for a mine slope. It has been successfully applied in various new slopes across the United States. This paper will detail the main concepts of the methodology including: (1) Analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) Primary and supplemental support design; (3) Long term support design in the form of steel square sets or arches, and (4) Validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011

By William H. Langer

Large amounts of limestone fines co-produced during the processing of crushed lime-stone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point sources such as cement manufacturing. AWL reactants are readily available, inexpensive and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid. This reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities to within about 10 km (6 miles) of the coastline. The majority of U.S. coastal power-generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufacturers and research scientists. There is a concern that CO2 generated from human activities is contributing to climatic and environmental changes. Approximately one-third of anthropogenic CO2 emissions come from burning fossil fuels to generate electricity. Each power plant is capable of emitting several million tons of CO2 annually. A variety of other industrial processes, such as cement manufacture, oil refining, and iron and steel production, also emit large amounts of CO2. The level of atmospheric CO2 can be reduced by capturing CO2 from point-source emissions and storing or sequestering it in isolation from the atmosphere (U.S. Department of Energy, 2003). In 1999, G.H. Rau and K. Caldeira proposed a geochemistry-based method that is referred to as accelerated weathering of limestone (AWL) in a paper titled ?Accelerating carbonate dissolution to sequester carbon dioxide in the ocean ? geochemical implications.?

Jan 1, 2009