Search Documents

Increase the productivity of domestic mining operations by improving the performance of rock drilling systems. Approach Investigate the use of chemical solutions at zero surface charge concentrations as drilling fluid additives to enhance penetration rates and extend bit life. Background Bureau researchers have investigated the use of chemical additives to enhance drilling performance and have found that the most efficient drilling occurred when the drilling fluid was able to maintain a zero surface charge (ZSC) on the rock surface. Laboratory drilling studies using 5/8-inch diameter diamond-impregnated coring bits on rock types such as quartzite, granite, taconite, and marble. Cationic compounds were used as the surface charge neutralizing additives during these tests. The drilling studies demonstrated enhanced drilling performance, however, only at the singular additive concentration that produced the ZSC condition. Bureau researchers made a breakthrough when they found that polyethylene oxide, although a nonionic polymer, was able to maintain the ZSC condition over a wide range of concentrations. Success using polyethylene oxide as the drilling fluid additive during subsequent laboratory tests prompted testing under field conditions.

Jan 1, 1991

By M. J. Kovalik

The effect of oxidation by air at temperatures ranging from 200° to 390° C on the change of chemical and physical properties of Pittsburgh-bed coal was studied as a function of processing time and temperature. The goal was to prepare a nonagglomerating fuel from a strongly coking coal for use in continuous carbonizing processes and in fixed-bed gasifiers. The oxidized coal was carbonized in a bench-scale apparatus, and the coke strength was evaluated in a Roga tumbler. Strength of the coke was progressively reduced with time of oxidation until the coking power of the coal was apparently destroyed. Time requirements to obtain an essentially nonagglomerating product were inversely related to processing temperature. Gaseous products released from the coal during oxidation reduced the yield of the desired nonagglomerating product, which decreased with time of oxidation at constant temperature and with increase in processing temperature at equal time. Oxidation at a temperature slightly above the lower limit of the plastic temperature range of Pittsburgh-bed coal was most effective because of the short processing time required and moderate processing losses.

Jan 1, 1963

By Robert C. Dyni

This report details the investigation of multiple-seam longwall subsidence conducted by the U.S. Bureau of Mines from 1978 to 1989. A field investigation monitored ground surface movements over four upper-seam longwall panels and six lower-seam panels. The characteristics of the subsidence occurring as a result of mining these panels are examined; in particular, the angle of draw, subsidence development, total magnitude and areal extent, and critical width are evaluated and discussed. Comparisons are also made between the characteristics of multiple-seam longwall subsidence and single-seam longwall subsidence that occurred at the same site.

Jan 1, 1991

By S. C. Termes

The Bureau of Mines conducted research on the flocculation of various minerals with insoluble cross-linked starch xanthate (ISX) to determine its potential as a beneficiation technique for low-grade, highly dissem-inated ores and for selective desliming. Covellite, chalcocite, pyrite, pyrrhotite, chalcopyrite, bornite, sphalerite, galena, and molybdenite fines flocculate with ISX. Floc formation, floc size, and settling rate are dependent on pH, with the pH dependence differing for each mineral. Quartz is not flocculated by ISX. Experiments to obtain selective flocculation of sulfides from quartz were attempted. Good selectivity was only obtained for the bornite-quartz system. postflocculation separations resulted in flocculated bornite in grades as high as 92 pet. Evidence is presented that the flocculation of many of the sulfide minerals with ISX may involve covalent bonding of the xanthate group to lattice metal site(s).

Jan 1, 1983

By Walter E. Lewis

A mothod of cutting St. Poter sandstono by streams of water under pressuro from nozzles and pumping the resulting, sand to the surface has roduced the cost of storm-sowor construction in the Minneapolis-St. Paul aroa. The hydraulic tunneling method, has boon in uso since 1934, and it is adaptable only to the lower part of tho St. Potor, sandstone, which lios within or just abovo the ground-wator levol. Tho upper part of the formation, immediately bolow tho Plattoville limestone, 18 comonted and camot bo mined by hydraulic mothods. The tunnel oporation observed in this instance is a main storm sowor starting at tho Mississippi Rivor below the 10th Avenuo SE bridge and will be drivon 6,000 foot at a grado of 1 foot por thousand undor the city of Minneapolis to Konnody and Arthur Stroots NE. A lateral storm sowor, which branchos from the main sovor at 8th Street SE, will oxtond from 10th Avonuo SE to 15th Avonuc SE. Tho tunnele are being drivon with the floor approximately at ground-wator lovol. All waters ontoring the main storm sower vill drain into the Mississippi Rivor. Tho main storm sewer cross soction is excavated to a roughly hox- agonal shapo 10 foot high by 10 foot wido at the contor. The upper half of the tunnol soction is solidly lined with either timber or stool. After all oxcavation is completed, the tunnel will be finished with a concrete circular lining 8 feet in inside diameter. The lateral storm sewer is excavated to a 5-1/2-foot by 7-1/2-foot section and will event- ually be finished with concrete to a modified horseshoe-shaped section 6 feet by 4 feet. Where the back or walls are considered unsafe during excavation, the upper half of the tunnel is lined solidly with timber. The equipment used by the Sower Division, City of Minneapolis, has been selected to meet a number of applications in storm-sewer work with diversified usage in mind. The sand pumps used on this job are rubber-lined, designed to work against a head of 100 foet. Either 4-inch or 6-inch diameter suction and discharge openings may be used. Other equipment, such as pipe, mine rail, flexible hoses, compressors, and general surface shop equipment, is drawn from a contral warohouse. It may be either new or used, depending on what is available at the warehouse. Much of the pipe and mine rail has been used for many years on several different tunnol jobs.

Jul 1, 1950

By John H. Soule

The Royal John mine was examined in November 1942 by a mining engineer of the Bureau of Mines, who proposed development of the Royal John and other properties in the area. Geologists of the U. S. Geological Survey studied the area in 1943 and 1944 and made definite recommendations. Also, in 1943 the Peru Miring Co. mapped the Royal John and did considerable diamond drilling. The Bureau of Mines started the Royal John portion of a project pertaining to the general district in April 1944. This project was completed in Juno 1945. The work, consisting of diamond drilling, was supervised by Robert O. Hill, mining engineer, and the results were published in Report of investigations 3904, Exploration of Grey Eagle, Grandview and Royal John Claims, Grant County, N. WIC. In 1947 and 1948 the Royal John was re-examined by a Bureau engineer, and additional development to increase the reserves of low-grade lead-zinc ore was proposed. This project was started in August 1948 and completed in Juno 1949.

Jan 1, 1950

By Thomas C. Atchison

The experimental work described in this report is part of a continuing study by the Federal Bureau of Mines of the fundamental physical processes involved in breaking rock with explosives. Six explosives were tested for their strain-producing abilities in a dolomitic marble. The explosives selected for testing had a tenfold variation in detonation pressure and a fivefold variation in characteristic impedance (product of loading density and rate of detonation). Strain pulses produced by the detonation of small charges of the explosives were recorded at distances of 5 to 130 feet. Peak strain, ?, was found to decrease with distance, R, in accordance with an exponential propagation law previously determined for other rock types, namely ? = (K/R)e ?aR The absorption constant, a, did not vary significantly with the explosive and was of the same order of magnitude as that for other rock types. The different explosives produced a fivefold variation in the value of the intercept constant, K.

Jan 1, 1961

By Carlton E. Brown

Broom and Yant6/ recently described a. microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter) and the thermal precipitator8/ . This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a micrcprojection method for counting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the ventilation Department of the Anaconda Copper Miring Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By L. A. Haas

The Bureau of Mines conducted bench-scale leaching tests with recycled spent copper electrolytes and copper-nickel mattes produced from the Minnesota Duluth Complex concentrates. This report describes the first stage of an overall two-stage leach operation. The objective of this research was to determine the matte-leach technology required to convert spent copper electrolyte into an enriched nickel liquor suitable for a nickel refinery and there-fore essentially free of copper, iron, and sulfuric acid. The experimental variables investigated were matte composition, particle size, spent electrolyte content, pulp concentration, oxygenation, temperature, and time. The time required to produce an enriched purified nickel liquor decreased with increasing pulp concentration, temperature, and oxygenation, but increased with increasing particle size and electrolyte copper and acid content. Nickel-rich (about 50 g/l) liquors at a pH of about 4 and containing less than 1 g/l of copper and iron were produced at 70° C by leaching minus 325-mesh low-iron (less than 5 pct) matte for 8 hours with spent electrolyte containing 22.4 g/l Cu, 28.9 g/l Ni, less than 0.1 g/l Fe, and 50 g/l H2S04 at a pulp concentration of 1 kg of matte per liter of spent electrolyteo Varying the nickel content of the spent electrolyte from 11 to 101 g/l appeared to have no appreciable influence on the matte leaching characteristics.

Jan 1, 1981

By B. J. Scheiner

Extraction of silver from silver mill tailings by an electrolytic oxidation procedure was investigated by the Bureau of Mines. Various parameters affecting silver extraction, such as electrolysis time, particle size, and dissolution of the silver as the tetrachloro or cyanide complex, were studied at 30° C with an electrolyte concentration of 20 weight-percent sodium chloride. Resulting silver extractions ranged from 77 to 90 percent, depending on the tailings being treated. Concomitant extraction of mercury ranged between 90 and 95 percent. Power consumption was 52 to 90 kilowatt-hours per ton for the tailings investigated. Comparative experiments using direct cyanidation resulted in extraction of 46 to 82 percent of the silver and 20 percent of the mercury. Cyanide consumption ranged from 3.3 to 9.4 pounds per ton of tailings, depending on the tailings being treated. Silver and mercury were recovered from leach solutions by precipitation on iron powder, followed by conventional distillation and fire refining steps.

Jan 1, 1972

By W. R. Huff

This report describes the development and operation by the Bureau of Mines of a pilot plant designed for using high-volatile A bituminous coal-in-water suspensions as a source of preheated coal and superheated steam in the pressure gasification of coal with oxygen. Figure 1 on page 2 is a block diagram of the integrated gasification process, in which a total of 70 tons of coal was fed from slurry and gasified. The present work included (1) development of equipment and methods both for mixing pulverized coal and water to produce slurry and for pumping and metering the slurry at gasification pressure; (2) development of equipment for heating the flowing slurry and, because slurry that can be pumped produces more steam than is necessary as a gasification reactant, developing equipment for removing and metering the excess steam; and (3) demonstration of the process under actual gasifier operating conditions, at a coal rate of about 800 pounds per hour and gasification pressures in the range 100 to 300 pounds per square inch gage. By using the forced-convection principle, a flow of slurry made from a caking, high-volatile A bituminous coal can be continuously heated to 600° F. in a coil-type heater. The flow rate and concentration of the slurry and the temperature gradient along the length of the heating coil must be closely controlled. In a radiant-type heater, involuntary reductions in flow rate, even momentary, can lead to coking and plugging of the heater coil.

Jan 1, 1961

By F. F. Aplan, J. A. Gutierrez-Rodriguez

"Contact-angle and flotation techniques were used to evaluate the influence of oxygen - both that inherent in the coal and that introduced by ambient temperature, aqueous oxidation - on a wide range of coal ranks. Oxidation was found to decrease the hydrophobicity and floatability of coal; with the effect being minor for coals of high rank but becoming increasingly important as the rank of coal is reduced. As an approximation, oxidation makes a coal behave as if it were one of lower rank. Frother only flotation' of coal· correlates with the captive-bubble contact angle whereas when oil is used as a collector, the flotation appears to follow the pattern shown by the water sessile drop on a fresh, un-reagentized coal surface. Coal recovery lost through oxidation may often be recovered by use of a variety of collectors, of which No. 2 foe! oil is among the best of those reagents tested. A simple alkali-extraction test may be used to estimate the influence of oxidation on coal preparation processes and use.INTRODUCTIONThe hydrophobicity of coal is not only a function of its rank but also of the extent of oxidation of the coal during and subsequent to its formation. Weathering and oxidation processes may proceed in-situ for coal deposits that outcrop near the earth's surface, or the oxidation of the coal particles may occur during mining, stockpiling or processing. Such oxidation, whether it affects the bulk-coal sample or on1y a thin outer layer on the coal surface, can dramatically influence the wettability of the particle and hence such processes as flotation, filtration, flocculation and dispersion.Many of the studies made on the oxidation of coals ·were designed to study its effect on flotation, coking or pyrolysis. The. present study 'is directed exclusively toward the effect of oxidation on the hydrophobicity and floatability of the coal. One of the first studies of the effect of oxidation on coal flotation was that of Sun [l] who found that as oxidation proceeds, coal becomes progressively more hydrophilic. Low-temperature oxidation (100-150°C for 250 h) generally lowered the coal floatability with an oily collector only slightly, but more extensive oxidation (200- 3500 C for 250 h) reduced coal floatability seriously. Sun also found that cationic amines were effective collectors for the oxidized coal which infers that oxidation makes the coal more negative in solution. He attributed the loss of floatability to be due to the accumulation of water-insoluble oxidation products at the coal surface. Gayle et al. [2] found that oxidation adversely affected coal flotation when an aliphatic-alcohol frother was used, though a small amount of oxidation appeared to improve the floatability of some coals using a kerosene-pine oil, collector-frother mixture in pilot-plant testing. Prolonged oxidation adversely affected the flotation recovery of the coals tested, the effect being more pronounced when an alcoholic-type frother only was used. They also noted that the reduction in floatability of lower rank bituminous coals was more affected by oxidation than was that of higher rank bituminous coals."

Jan 1, 1989

By Paul S. Schopf

The results of an experimental investigation into the possible use of medium energy acoustic fields (130 to 140 dB) to precipitate 1 to 10 micron particles is presented. The aerosol was produced with a LeMer generator using oleic acid and nitrogen. The sound field was a sinusoidal standing wave field in an acrylic tube, with light transmission data used for concentration determination. The results showed collection efficiencies of up to 80% on 2 micron particles with a residence time of 11.8 seconds at a sound pressure level of 139 dB re 2x10-5 N/m2. A discussion of the possible turbulent mechanism is made, as well as review and comparison with others? work.

Jan 1, 1972

By Robert W. Smith

[In a certain application it was necessary to compute the incomplete beta function, ß(1/2, p, q), for a certain set of values of p and q. Since the set of p and q values was much more finely spaced than those in any published tables, the authors have decided to make their results available in this report. In connection with this application, the function ß(1/2, p, q) was needed at various points in the p, q plane at intervals of 0.05, 0.05 p = 2q < 10.00. Fletcher, Miller, and Rosenhead3/ state that the only tables available in the desired range are those of Pearson.4/ However, the interval used by Pearson was not small enough for the present application. For this reason, it was decided to calculate the function ß(1/2, p, q) for p = q = 0.05 (0.05) 10.00. This table is published because of the fundamental importance in mathematical analysis of the incomplete beta function.]

Jan 1, 1953

By A. F. Colombo, D. W. Frommer

Bench- scale tests were made to determine the applicability of flotation as a means of upgrading finished and semifinished magnetic concentrates prepared from reductively roasted iron ores . Both anionic and cationic flotation methods were used to remove siliceous gangue from the magnetic concentrates and produce upgraded products . Seven magnetic concentrates , containing from 6.7 to 13.7 percent SiO2 , were improved by the flotation treatment , yielding final concentrates containing less than 6.0 percent Si02 . Cationic flotation methods were studied on four of the seven samples ; of this group only one sample yielded better results by cationic flotation than by the anionic method .

Jan 1, 1964

By Carlton E. Brown

Brown and Yant6/ recently described a microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter7/ and the thermal precipitator8/. This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a microprojection method for courting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the Ventilation Department of the Anaconda Copper Mining Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By E. L. Burwell

Preliminary results of an in situ oil shale retorting experiment conducted by the Bureau of Mines in a shallow bed of Green River oil shale at Rock Springs, Sweetwater County, Wyo., are described. Eleven wells were drilled into a 20-ft-thick section of the shale lying between 68 and 88 It deep, and attempts were made to connect the wells through the shale with a fracture system created by application of high-voltage electricity (electro-linking), hydraulic fracturing, and explosive fracturing. Ignition of the shale through the central well was easily achieved with a propane burner, and shale oil began to collect in three wells within 3 hours. Propane injection was discontinued after 7 days, and combustion continues, although attempts to control the direction of the combustion front have been unsuccessful. Production rates as high as 4 ½ barrels of nil per day have been recorded, but too little is known about underground conditions to permit an estimate of recovery efficiency at this time.

Jan 1, 1969

Objective Develop a method to warn of hazardous conditions and enhance safety during operation and inspection of vertical mine shafts and hoists. Background Mine hoisting is the most critical and potentially the most dan¬gerous operation in underground mining. Many hazards are related to falls of miners and materials, ground instability, and malfunction or lack of safety devices. All have the potential to cause a cata¬strophic accident. A condition known as "slack rope" is particularly dangerous, expecially if it occurs without the operator&apos;s awareness. The most common occurrence of slack rope is in metal or nonmetal mines that have a history of ground control problems near the "haft. Approach Studies of hoist safety features and Mine Safely a and Heath Administration (MSHA) accident statistics suggests a need to measure wire rope tension, conveyance speed and position, and shaft guide misalignment. The most accurate data are obtained directly from the conveyance. Such data could warn of potentially dangerous situations during hoisting operations, as well as during inspections, maintenance, and lowering of large equipment. Figure I shows the concept for monitoring wire rope tension, conveyance position, and guide displacement. Progress to Date A conveyance-mounted system has been developed that monitors rope tension: hoist conveyance position, speed, and load; and shaft guide misalignment. A "flex-beam" load sensor mounted just above the- conveyance protects against slack and tight rope. The measurements are transmitted 60 times a second via wireless equipment from the conveyance to the hoist room. An encoder mounted on the conveyance eliminates the need to correct the position because of rope stretch. Figure 2 shows the encoder wheel and guide displacement sensors being mounted on a cage in¬spection deck. A potentiometer monitors misalignment of the shaft guides during inspections. Information about the cage or skip can be acquired by the shaft inspector using a hand-held indicator. Inspection can also he conducted remotely from a station or hoist room using the wireless link to a laptop computer. Figure 3 shows test results from a simulated slack rope condition. Patent Status NIOSH has a patent pending on this device entitled "Cable-Load¬Sensing Device." For More Information NIOSH is seeking cooperators to assist in further tests of this technology to improve hoisting safety. Additional information can he obtained by contacting Michael J. Beus, Steven Iverson, or Elaine Cullen, Technology Transfer Officer, NIOSH, Spokane Research Laboratory, Spokane, WA 99207 at (509) 354-8000.

Feb 1, 1998

By Ronald A. Munson

Samples of the naturally occurring zeolites phillipsite, clinoptilolite, erionite, and chabazite have been surveyed for their gas adsorption, ion exchange, and other characteristics. Chabazite and erionite, which are generally more stable, also have higher methane adsorption capacities than do the other natural zeolites. Both natural erionite and natural chabazite are classified as small-port zeolites on the basis of their inability to adsorb chlorotrifluoromethane. In the range of 8 to 100 mesh, the adsorptive capac-ity of natural zeolites is improved only slightly by a decrease in particle size. The capacity of natural clinoptilolite to adsorb methane is increased by cation replacement by the hydrogen ion and decreased by exchange with calcium ion. Natural phillipsite, which is easily decomposed by heat, adsorbed methane to a limited extent.

Jan 1, 1973

By John P. McDonnell

Coal mine bounces and bursts are major problems facing U.S. mine operators. Bounces and bursts have the potential to inflict severe injury on mining personnel, damage equipment, and cause mine closures. High- stress conditions, at or near the working face, are the common denominator in the burst problem, If mine operators can locate high-stress and potentially burst-prone zones, they can then use stress-relief methods to control the burst condition. One method of locating the high-stress zone is the probe-hole-drilling or drilling-yield method. Probe-hole drilling is used frequently in Europe, the U.S.S.R., and Japan as a means for locating potential burst zones. Consequently, the Bureau of Nines performed tests in the laboratory and in a deep, burst-prone western mine to analyze probe-hole drilling. The in-mine method, very simply, involves drilling a hole into the coal seam and measuring the volume of cuttings obtained. A certain volume of cuttings can be expected from a certain diameter and length drill hole. A significant increase in the volume of cuttings means the zone around that particular hole is highly stressed. In-mine use of the drilling yield method has shown it to be a useful tool for locating highly stressed and potential burst zones. Results from laboratory testing confirm that high stress applied tri-axially to a cube specimen will cause a significant increase in the volume of cuttings from a small-diameter drill hole in the specimen.

Jan 1, 1988