Search Documents

By E. K. Stanek

This volume describes software developed for programmable calculators that is useful in the analysis and design of mine electrical power systems. The programs are equally useful for any industrial or commercial power system. All programs are written for both the HP-97 and the TI-59 programmable calculators. Listings of both versions of the twelve programs that were developed appear in the report. The programs that were developed can be broken into two groups. The first group encompasses design-oriented programs. The second group encompasses analysis programs. For each program the following items are provided: a description of the program's capabilities, the solution technique used, instructions on how to use the program, a worked out example with data and results and, finally, listings of the programs for the HP-97 and TI-59 programmable calculators. Typical problems that can be attacked with these programs include ground bed design, selection of contactor size, fuse size, relay settings, instantaneous overcurrent trip settings for trailing cables, allowable cyclic cable loading, short circuit analyses, prediction of transient voltages and others.

Jan 1, 1979

By Richard A. Allwes

This U.S. Bureau of Mines report presents the results of structural analyses and full-scale physical tests conducted on a steel-set arch and tri-set. The purpose of the analyses and tests was to evaluate the suitability of these structures for use in roof-fall prone areas. The arch canopy test and design procedures previously developed by the Bureau were utilized in this evaluation. Theoretical resistance functions were established for the steel-set arch and tri-set and were representative of the experimental behavior of the structures. The resistance functions were used to determine the energy absorption capacity of the structures and to predict their dynamic response to impact loading. The dynamic tests demonstrated that the arch canopy design procedure is appropriate for tri-sets and yields conservative designs for both steel-set arches and tri-sets. As a result of this work, it is recommended that these two structures may be considered for use in roof-fall prone areas and for rehabilitation work, provided the arch canopy design procedure is utilized for each application and the principles underlying the design procedure are understood.

Jan 1, 2010

By John C. Gagliardi

The size and complexity of modern surface haulage trucks has resulted in an increased reliance upon sensors and electronic-based instrumentation for safe and efficient operation. Design engineers need accurate information about the equipment vibration environment to efficiently and effectively build components for installation on mobile mining equipment capable of withstanding the mine environment. Examples of such components include backup alarms, communication equipment, microprocessor-based controllers, and a wide variety of sensors. Unfortunately, this information is not available to the majority of both original equipment and aftermarket equipment manufacturers. To address this problem, the U.S. Bureau of Mines performed field vibration measurements on a variety of surface mining haulage trucks. The vibration measurements were then analyzed and test specifications were developed in the form of envelopes. In conjunction with test specifications, recommendations to aid manufacturers in implementing a vibration environment test program have been included with an illustrative example.

Jan 1, 2010

By J. B. Gayle

Oven widths for experimental and commercial slot-type ovens differ appreably in most instances; the experimental ovens usually ranging from 10 to 14 inches and the commercial units from 14 to 21 inches. Application of results obtained with experimental ovens to commercial practice thus requires major extrapolations. A critical survey of the literature indicated that sufficient information about the effects of variations in oven width on the carbonizing process is not available to permit such extrapolations to be made with any considerable degree of confidence.

Jan 1, 1960

By Bertrand L. Johnson

Langbeinite, a comparatively rare mineral that has been reported from only five countries in the entire world, has recently attained considerable economic importance in the United States and Poland. Since September 1940, several hundred thousand tons have been produced in one of the Carlsbad (N. Mex.), potash mines for chemical and fertilizer use. As it is a newcomer in this field, and as it is the source of fertilizers possessing special advantages, notably for soils deficient in magnesium or requiring sulfate fertilizers, a discussion of its properties, occurrences, uses, mining, and treatment is appropriate at this

Jan 1, 1944

By O. C. Blade

A summary of the characteristics of motor gasoline for the summer 1951 is presented in table 1, and for comparison, a similar summary for the summer 1950 is shown in table 2. Trends of some of the more important characteristics over a period of years are shown in figures 1 and 2. As indicated, octane numbers of motor gasolines sold in the United states decreased approximately one-half to one octane unit from the record levels attained during the winter of 1950-51 and are a little below the octane numbers of summer 1950. However, average vapor pressures of the summer gasolines did not change, and certain distillation temperatures varied only slightly from those of the year before.

Jan 1, 1952

By Murray Greyson

A number of tests were made with various methanation catalysts in fixed-bed, conventional fluidized-bed, and multiple-feed, fluidized-bed equipment to develop catalysts and processes for methanation of synthesis gas. The results show: 1. Methanation reactions may be carried out in 1-inch, bench-scale equipment at high synthesis-gas throughputs with good temperature control of the reactions if a multiple-feed type of fluidized-bed design is used. 2. Nickel is superior to iron as a catalyst for the methanation of synthesis gas, unless the process is considered in terms of a combined operation that produces both gaseous and liquid products. 3. Techniques of catalyst preparation determine, to a large extent, the process life of nickel catalysts, and these techniques must be thoroughly investigated before any conclusions can be reached. 4. Enough data are available to indicate that the sulfur concentrations in synthesis gas that is used for methanation are extremely critical, and maximum process limits should be carefully evaluated.

Jan 1, 1955

By R. Karl Zipf, Z. T. Bieniawski

"Abstract. Based on the premise that understanding the fundamental mechanics of fine fragment formation in coal will lead to reducing coal dust problems in mines, a thorough study of the mechanics of crack propagation in coal was undertaken. Two approaches were considered in an attempt to understand and quantify the fracture process as it relates to fine fragment formation.In one approach, theoretical models are used which describe the size of the fracture process zone which may relate to the amount of structural damage and fine fragment formation on the new crack surface. The other approach is based on the relationship between crack tip stress intensity and new surface appearance for mixed mode crack propagation. Preliminary observations with a scanning electron microscope support the premise that fine fragment formation is related to fracture surface appearance and fracture initiation conditions.An experimental program designed to supply the input parameters for these approaches is presently underway. The experimentation features mixed mode fracture toughness testing, using a special mixed mode testing rig, and fracture velocity measurements with a crack propagation gage. The interpretation of this data via the approaches discussed will provide further understanding of the mechanics of fine fragment formation in coal."

Mar 1, 1989

By L. B. Pankratz

Heat content measurements were conducted for GaPo.996 and InPo.986 over the temperature range from 298° to 1,100° K, and for In2S2.897 over the range from 298° to 1,200° K. Both the actual experimental data and values adjusted to conform with the stoichiometric compositions (GaP, InP, and In2S3) were reported. Entropy increments above 298.15° K were calculated for the stoichiometric compounds, and heat content and heat capacity equations were derived.

Jan 1, 1965

By William E. Bruce

The Bureau of Mines performed drill calibration tests on two industrial percussive drills of 2-5/8- and 3-1/2-inch piston diameters to determine operating characteristics for their use in conjunction with penetration rate data in developing drillability equations and furthering the knowledge of percussive drills. The use of a linear velocity transducer for measuring piston velocities and application of its instrumentation are described. Data presented include relationships between maximum piston velocity and feed air pressure other results confirm the theory or data of previous investigators, and some comparisons are made with the performance prediction formulas of other investigators.

Jan 1, 1969

By William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to' several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 2010

By Charles K. Rose

The Cebolla Creek titaniferous iron deposits near Powderhorn in southern Gunnison County, Colo., were examined by the Federal Bureau of Mines as part of an overall program to investigate the Nation's titanium and iron resources. The deposits occur around the periphery of the Iron Hill stock, which underlies an area of about 12 square miles. Concentrations of magnetite, ilmenite, and perovskite arc localized along fractures in the pyroxenite stock. Mineralogical studies of composite surface samples collected in 1956 showed that most of the iron is present in ilmenite-bearing magnetite. Perovskite is the chief titanium mineral in the magnetite-rich and augite-rich types, and sphene is the principal titanium mineral in the placer material. The mica-rich rock contains approximately equal amounts of perovskite, ilmenite, and sphene.

Jan 1, 1960

By T. M. Ruff

A prototype mucking machine designed to operate in narrow-vein stopes was developed by Foster-Miller, Inc., Waltham, MA, under contract with the U.S. Bureau of Mines. The machine, called a compact loader-trammer, or minimucker, was designed to replace slusher muckers in narrow-vein underground mines. The minimucker is a six-wheel-drive, skid-steered, load-haul-dump (LHD) machine that loads muck at the front with a novel slide-bucket system and ejects it out the rear so that the machine does not have to be turned around. To correct deficiencies of the tether-remote-control system, a computer-based, radio-remote-control system was retrofitted to the minimucker. Initial tests indicated a need to assist the operator in guiding the machine in narrow stopes. An automatic guidance system that used ultrasonic ranging sensors and a wall-following algorithm was installed. Additional tests in a simulated test stope showed that these changes improved the operation of the minimucker. The design and functions of the minimucker and its computer-based, remote-control system are reviewed, and an ultrasonic-sensor-based guidance system is described.

Jan 1, 2010

By Alan J. Fejes

As part of its mine subsidence research program, the Bureau of Mines and the American Electric Power Co. cooperated on a study, conducted at the Price River Coal Co. No. 3 Mine, directed toward developing the capability to estimate the surface subsidence resulting from longwall mining in a geologic, topographic, and mining environment common to coalfields in the Western United States. Subsidence was monitored at the No. 3 Mine over two adjacent longwall panels. The subsidence study area was reduced when the two planned panels were reduced in length because of equipment failure and a mine fire. Subsidence was measured for 21 months. Subsidence continued for 6 months after mining had been completed. A maximum of 2.2 ft of subsidence occurred over the two longwall panels mined at an overburden depth ranging from 300 to 1,500 ft.

Jan 1, 1986

By R. M. Santmyers

Umber and sienna, like ocher, are naturally occurring mineral pig- ments composed largely of clay permeated with hydrated iron (ferric oxide), but they differ from ocher in that they also contain hydrated manganese oxide. The presence of manganese accounts for their browner color. In addition to silica and alumina (clay) and the coloring oxides of iron and manganese, these pigments often contain lime, barium, and other metallic salts as impurities. Sienna most nearly approaches ocher in chemical composition, and the chief distinction is its physical character. It grades into ocher with de- creasing iron content and into umber with increasing manganese content. Sienna is translucent rather than opaque and is more of a stain than a pigment; as the iron oxide content is rather high (often 60 to 80 per cent), the color is strong and rich and varies from pure brown to reddish brown. This pigment raw sienna, terra di Siena, and Italian earth. is known under several names: Burnt sienna is a pigment of an orange-brown tint made by cautionsly calcining raw sienna. It is divided into two grades; American, and Italian burnt sienna. American burnt sienna is a reddish-brown pigment containing from 25 to 60 per cent iron oxide (Fe2O3). One grade, found in Pennsylvania, analyses as high as 80 per cent and is mown as double strength sienna. Italian burnt sienna is a pigment generally containing more iron than the American product, averaging 60 to 75 per cent iron oxide.3 American pig- ments of the same iron content differ materially in shade, having a Havana- brown color, whereas the Italian is more of a maroon. Italian siennas when tinted with 20 per cent of white, show a bluish tint, whereas American siennas yield a brownish or yellowish hue. Raw umber, also known as Turkey umber, Levant umber, and terra ombra, is a greenish to yellowish brown siliceous and ferruginous earth, containing a considerable proportion of one or other of the higher oxides of manganese, Mng04 and MnO2." It is similar in many respects to raw sienna except that it is much coarser and contains more manganese oxide. All umbers contain over 5 per cent of manganese dioxide. Like sienna, umber is a permanent pigment, not being injured by light or by impure atmospheres. Burnt umber (velvet brown, chestnut brown, etc.), results from the calcination of raw umber. The color is much richer and warmer than that of the raw umber. The colors are equally permanent and can be used in conjunc- tion with all other durable pigments.

Sep 1, 1931

By R. C. Hickman

"INTRODUCTION The largest known deposits of ilmenite and rutile in Virginia are in Amherst and Nelson Counties. Other deposits occur in the State, but their extent is not known. One of the most promising of the latter is the deposit in Roanoke County on the T. M. Bush and the H. L. Hutchins property near Roanoke. A geophysical survey was made of the deposit, followed by core drilling. In April and May 1946, four holes were drilled, totaling 822 linear feet.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch,. Bureau of Mines."

Aug 1, 1947

By John Ward Smith, Neil B. Young

Shale specific - gravity to oil - yield relationships were developed for black shales of the New Albany Formation of Kentucky from data collected on core samples representing the complete section of the formation in three counties . Linear equations for estimating oil yield from measured specific gravity and for estimating specific gravity from measured oil yield were shown to be applicable within small error limits to all the sites tested . Variation in pyrite content is the largest source of error .

Jan 1, 1964

By Christopher D. Risbrudt

In this comprehensive study of the use of wood products in coal mining, a sample of over 220 mines provided data by questionnaire. Wood use per ton of underground coal was found to vary substantially by mining process and region. In the Eastern Coal region, 1.6 board feet of wood was used per ton of coal, wel above the 0.6 board feet usage per ton in the West. The kind of timber used varied also by Region. Hardwood use is about 40 times greater than softwood in the Eastern Region. There, hardwoods are plentiful, relatively cheap and strong. In the West where softwood forests predominate, softwoods were 2-1/2 times more common in mine wood use than hardwoods. Nearly 80 percent of the wood used in underground coal mines is used in cross bars and props. Nearly 54 million cubic feet of wood products were used in coal mining in the sample year 1979; about twice as much going to underground mines as surface mines. Wood requirements for mining were projected to 2030 for a range of three oil price scenarios. Much greater wood use will be required for greater coal output.

Jan 1, 1982

By Gennaro G. Marino

The Bureau of Mines and the University of Illinois investigated surface characteristics and damage to structures from mine subsidence over a room-and-pillar coal mine in Hegeler, IL. Data on three adjacent subsidence sags and associated structural damage were collected, summarized and evaluated. The subsidence sags developed over a 10-year period and took place above a modified room-and-pillar operation mining the Herrin (No. 6) coal at a depth of 130 to 135 ft. Surface vertical displacements of 3.0 to 3.5 ft resulted from extracting 6.1 to 6.4 ft of coal. Ground movements associated with sag formation severely damaged three houses and a radio station building, broke numerous utility lines, and structurally distorted three radio transmission towers. The radio station was remodeled and the towers repaired, but the three houses were subsequently demolished. Surface waters collecting in the subsidence depressions caused failure of radial ground transmission systems. The following subsidence profile characteristics were determined at the radio station and one of the houses, respectively: profile slopes, 0.02 and 0.07; maximum curvatures, 2.3 x 10-4 ft-1 and 3.0 x 10-4 ft-1; and angular distortions, 6.6 x 10-3 and 62.0 x 10-3. Although the house was more severely damaged than the radio station, both structures are classified as severely to very severely damaged.

Jan 1, 1986

By J. E. Wilson

A bench-scale expansion tester using 71 grams of coal was developed to determine the practicability of an apparatus of this size to investigate the effect of variables such as oxidation, blending, bulk density, inerts, size consist, petrographic differences, and rate of heating on the expanding properties of coal. The value of this tester is shown by the correlation that exists between its results and those of the larger scale sole-heated oven expansion apparatus used in commercial plants. From tests on 32 coals the standard error of estimate for predicting sole-oven results from bench-scale results is ± 5.3 percentage points. A standard deviation of the difference between pairs of tests in the latter apparatus of ± 2.1 percentage points was determined for 31 samples. In the sole-heated oven test the expansion of a coal at constant pressure is directly proportional to the dry coal bulk density. Tests in the bench-scale tester show a similar relationship between expansion and bulk density. When the blending ratios of high-and low-volatile coals are varied, similar changes in expansion are observed in both the sole-heated oven and the bench-scale tester. Therefore, the effect of other variables on expansion should be similar in the latter apparatus.

Jan 1, 1960