Search Documents

By J. A. Taylor, H. F. Yancey

"INTRODUCTION Froth flotation as applied to coal is a process for separating desirable carbonaceous material from undesirable inorganic matter. In general, the feed must be finer than one eighth inch in size. The principal use of the process in the preparation of coal appears to be in the treatment of the fine sizes produced by breakage during mining and preparation.The Bureau of Vines in Information Circular 6714 has published general information on coal flotation, summarized investigative studies of the process, and described operating plants throughout the world with their tonnage, reagent consumption and operating costs.4ACKNOWLEDGMENTSThe present study of means for depressing pyrite and reducing ash ty froth flotation was conducted at the Northwest Experiment Station of the United States Bureau of Wines in cooperation with the College of vines. University of Washington, under the general direction of A. C. Fieldner, chief engineer, Experiment Stations Division, Bureau of Wines. Grateful acknowledgment is made for suggestions and criticisms received from W. H. Coghill, supervising engineer, U.S. Bureau of Mines Mississippi Valley Experiment Station, Rolla, Mo.; J. B. Morrow, and R. E. Zimmerman, of the Pittsburgh Coal Co.; and Dean Milnor Roberts and Prof. Joseph Daniels, of the College of Mines, University of Washington.FLOTATION AND DEPRESSIONA substance will tend to float if its surface attracts a gas film more strongly than it does a liquid film when both air and liquid are competing for this attraction. On the other hand, a substance will not float if its surface attracts a liquid film more strongly than it does a gas film. All theories of depression depend upon this fact. A wetted particle of floatable size most likely will be found in the tailings after the flotation process has been completed.The crux of flotation is the selective wetting of the undesirable material that tends to float. Two general methods 5, 6, 7 of depression are in use: One combines a chemical substance with the surface to form a wettable compound, and the other employs some colloidal or ionic substance which the surface selectively adsorbs, thereby forming a wettable surface."

Jan 1, 1935

By Jalna R. Zatko

Coal-clay waste slurries were dewatered in laboratory-and small-scale continuous tests by the Bureau of Mines using polyethylene oxide (PEO) as a flocculant. Dewatering from a nominal 7-wt-pct solids to over 50-wt-pct solids was accomplished using 0.5 lb of PEO per ton of feed in small-scale continuous tests. Parameters such as pH, initial solids content, and PEO concentrations were investigated. Water recovered from dewatering was reused as dilutant for PEO solutions.

Jan 1, 1982

By F. J. Cservenyak

The Bureau of Mines Solid Waste Program is directed toward three main areas of research: (1) Extraction of mineral, metal, and energy values from urban refuse; (2) recovery of mineral and metal values from wastes generated in the industrial extraction, processing, and utilization of raw materials and mineral-base products; and (3) upgrading and utilization of automotive scrap. The Bureau also has a contract and grant program which supplements the in-house research and aids in the training of personnel in the proper management of mineral- and metal-based solid wastes.

Jan 1, 1970

By John E. Hamak

The U.S. Bureau of Mines estimates the identified helium resources of the United States at 630 Bcf as of December 31, 1990. This includes 295 Bcf of demonstrated reserves, 87 Bcf of demonstrated marginal reserves, and 42 Bcf of demonstrated subeconomic resources. The identified resources include 161 Bcf of helium in inferred and marginal reserves and 45 Bcf in inferred subeconomic resources. The identified helium resources contained on Federal lands are approximately 170 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. In addition to the identified helium resources, undiscovered helium resources in the United States are estimated at a most likely volume of 103 Bcf, with a maximum volume of 259 Bcf and a minimum volume of 41 Bcf. Also reported are 43 Bcf of helium in nonconventional and low-helium-content natural gases. Current extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1990 was 2.5 Bef. If current trends continue, some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1993

By G. L. Gates

The Bureau of Mines in cooperation with the City of Long Beach) Calif.) studied some physical factors effecting the deposition of barium sulfate scale in oil-well rotary pumps. Freshly formed barium sulfate was obtained by combining sulfate in sea water with barium from a barium chloride solution. The rate of scale deposition was measured quantitatively by weighing the pump impellers and diffusers. The results of the tests showed that coating the impellers with plastic significantly reduced the rate of barium sulfate deposition.

Jan 1, 1967

By Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2007

By P. R. Tisot

Knowledge acquired from this research contributes to a better understanding of the physical structure of Green River oil shale and provides fundamental data and concepts that may serve to improve oil-shale technology. This study by the Bureau of Mines indicates that oil shale is a highly consolidated organic-inorganic system with no significant micropore structure, pore volume, or internal surface. This system is a form of physical structure that precludes rapid diffusion of either gases or liquids. The mineral matter consists essentially of nonspherical particles that tend to follow a log-normal size distribution. An excess of 99 weight-percent of these particles have equivalent spherical diameters of less than 44 microns--75 weight-percent are from 2 to 20 microns, and 15 weight-percent are less than 2 microns. The surface area (3 to 5 square meters per gram) of these mineral constituents is mainly external surface. The mineral constituents contain some micropore structure--pore radii ranging from 10 to 100 Angstrom--with the pore sizes randomly distributed. Distribution of the organic matter within the inorganic matrix is essentially interparticle and not intraparticle. The organic matter within the micropores of the mineral constituents is less than 4 percent of the total. Estimates made from surface area data suggest that perhaps only a small amount of the organic matter is bonded either physically or chemically to the mineral constituents.

Jan 1, 1963

By E. J. Gleim

To make a thorough survey of a coal mine in order to eliminate hazards, the competent safety engineer must be familiar with mere than one branch of engineering. It is essential that he know the properties of mine gases and the methods of detecting them, as well as hew to prevent dangerous as accumulations. It is also essential that he understand the action of overlying strata when the coal is removed, and the proper methods of protection by timbering or other suitable means of support. He must know the value of protective clothing in reducing injuries and mast be informed as to the correct handling and use of explosives to avoid premature blasts, misfires, and ether failures in blasting practice. He must understand hew to operate locomotives and cutting, loading, and various other types of machines to be able to recommend effective safeguards for protecting the men who use them in addition to being informed as 'to these and many ether activities connected with the mining of coal, he must net overlook electrical engineering if he wishes to combat the fire, shook, and ignition hazards attendant upon the use of electrical machinery and circuits in and around the mine intelligently. There are many points relating to safely in the selection, maintenance, and use of electrical circuits and equipment that are perfectly obvious to the electrical engineer but perhaps are not se evident to those not trained in this particular branch of engineering. Engineers of the U.S. Bureau of Mines who have made a special laboratory study of electricity as related to safety in minus haw e also made inspections of electrical installations at a large number of bituminous mines. These inspections have revealed practices and conditions that not only do not contribute to safety but that add nothing to efficiency and economy in the operation of the mine.

Jan 1, 1936

By E. D. Gardner

This is one of a series of papers written for the consideration of operators of small gold and silver mines in the West. The paper discusses smelting schedules, general smelting practices that have a bearing on rates, and the reasons for penalties or credits for certain constituents of ores. Crude gold and silver ores generally are shipped to smelters only when milling facilities are not available; however, high tailing losses in milling a high-grade or refractory ore or low smelting rates because of the fluxing value of an are may make direct smelting more economical.

Jan 1, 1936

By E. D. Gardner

This paper is a progress report on the study of mining methods and costs in the western United States and summarizes that part of the work pertaining to the undercut block-caving method of mining. Ore is mined on a large scale exclusively by the undercut block-caving method at the following six mines in the western United States: The Morenci branch of the Phelps Dodge Corporation, Morenci, Ariz.; the Ray mines of the Nevada Consolidated Copper Co. at Ray, Ariz.; the Inspiration Consolidated Copper Co. at Inspiration, Ariz.; the Miamo Copper Co. at Miami, Ariz.; the Ruth mine of the Nevada Consolidated Copper Co. at Ruth, Nev.; and the Consolidated Coppermines Corporation at Kimberly, Nev. The undercut block-caving method is also used at the mine of the Andes Copper Mining Co. at Potrerillos, Chile.

Jan 1, 1930

By William H. Pomroy

Spontaneous combustion fires involving high-sulfide-content ores are a relatively infrequent yet serious safety hazard in mining. They are also the cause of lengthy mine shutdowns because they typically occur in areas of a mine where abundant fuel material is present but which are inaccessible for fire fighting. This Bureau of Mines report describes research to design, fabricate, and test in the laboratory and field a system that warns of spontaneous combustion fires in metal mines. Overall performance of the detection system was found to be satisfactory, in that the system was capable of reliably detecting low levels of combustion products believed to indicate the preflaming stage of spontaneous combustion in metal mines. Installation of similar systems in mines with a high risk of spontaneous combustion is recommended. Principal operating problems and recommended corrective actions are also discussed.

Jan 1, 1987

By Albert J. Forney

Extensive studies have been made of the various effluents found in the Synthane coal-to-gas process. Analyses have been made of the waters, gases, and trace elements present in some of the streams. Results of analyses show the water effluents are the area where extensive research is needed.

Jan 1, 1974

By Ludwig Schmidt

This report, the second of a series, presents the results of laboratory corrosion studies which were made in connection with a one-year test on aluminum lease tanks conducted by the United States Bureau of Mines. Part 1 of the report contains the results of the field tests. The studies were made on an oil lease in a so-called "sour district," near Borger, Tex., where free hydrogen sulphide accompanied the production of oil, gas, and salt water. Steel tanks previously used on the lease had suffered severe corrosion, because steel is inherently susceptible to attack by hydrogen sulphide. Because of the high resistivity of aluminum to the action of hydrogen sulphide, it was believed that this metal had promising possibilities as a material for the construction of lease tanks in "sour districts." The results of the one-year field test proved that aluminum lease tanks will withstand corrosion by hydrosulphide, but it as found that aluminum was susceptible to attack by salt water, which was invariably present in certain portions of the tanks, and that hydrogen sulphide accelerated this salt-water corrosion in an indirect manner, as will be explained hereinafter. In order to study corrosion conditions encountered in the tanks during the test period, a laboratory was maintained at the site of the aluminum lease tanks.

Jan 1, 1931

By Robert L. de Beauchamp

The Bureau of Mines reviewed aluminum chloride technology to determine the problems associated with its preparation from minerals, and to ascertain the best areas for research to solve these problems. Commercial AlC13 production processes are described and the ?state of the art? for the preparation of AlC13 from aluminous materials is evaluated. Areas for further research are indicated.

Jan 1, 1969

By George L. Gates

The Bureau of Mines studied pressure-buildup data from a number of California gas wells to determine if the reservoir properties calculated from these data correlated with field-observed reservoir properties. Pressure-buildup curves from 24 wells showed distinct changes in slope, indicating changes in permeability of the reservoir rock. Calculated distances from the wells to indicated permeability changes were in fair agreement with distances deter-mined in the field. Pressure-buildup curves from three wells had more than one distinct change in slope, indicating multiple permeability changes. Thus field data supported the theoretical relations used to calculate reservoir properties from pressure-time relations measured in gas wells.

Jan 1, 1967

By Raghoottma S. Pandurangi, Mohindar S. Seehra, Pedro Bolsait, Bronwyn L. Razzaboni

"Surface IR (infrared) modes of crystalline and fumed (amorphous) silica particles, calcined at temperatures up to 1095°C, have been studied by Fourier transform infrared spectroscopy. The ability of these same particles to lyse cells has been measured by a hemolysis protocol. The untreated crystalline and amorphous materials differ by a factor of 40 in specific surface area, and the intensity per unit mass of the sharp surface silanol band near 3745 cm-1 in the amorphous material is an order of magnitude larger than in the crystalline material. A similar difference is observed in the lysing potential of the two materials. The intensity of the silanol band increases after calcination for both materials, reaching peak values near 500°C, followed by a dramatic drop at higher calcination temperatures, and reaching negligible values for materials calcined near 1100°C. The lysing potential data follow essentially the same pattern for both crystalline and fumed silica. These results are consistent with the hypothesis that the surface silanol groups are involved in cell lysis. Further experiments are suggested to evaluate the relationship between the surface structure of ailica particles and their potential cytotoxicity. IntroductionThe characterization of the surface structure of various allotropic forms of silica is of interest because the cytotoxicity of silica particles of respirable size has been commonly related to the chemical interaction of functional groups on the surface of such particles with the lipoproteins contained in cell membranes (1-3). It has been found that the cytotoxic potential of silica particles varies greatly with their crystalline structure (4,5), particle size (6-8), surface composition (9), and molecular surface configuration (1,10). Studies of the infrared (IR) modes of various forms of silica have been reported by a number of researchers (3 ,11-19). Several books and reviews (20-24) have dealt with the identification of functional groups on silica surfaces and the effect of heat treatment on the surface structure. The nature of the surface is said to be critical in determining the biological activity of silica dusts (3).Fourier transform infrared (FTIR) spectroscopy is a highly sensitive ·technique for identifying IR surface modes of tine particulates, and it was deemed of interest to examine the surface structure and its relation to lysing potential of two widely different types of respirable silica dust. The lysing potential of respirable dust particles has been considered a first-level test for potential cytotoxicity."

Jan 1, 1990

By James A. Browning

Conventional flame channelling operates continuously at over 120 db --flame-drill channelling at a maximum of 95 db. The latter process was developed under this program. Individual drill holes are spaced to leave narrow rock webs. Sound and dust passing from the hole are effectively treated by a muffler and water injection.

Jan 1, 1980

By R. W. Stahl

One of the broad purposes of the Bureau of' Mines since its establishment has been conservation of mineral resources. As some of the coal beds approach depletion, especially those coals suitable for making metallurgical coke, more and more attention is being given to means of recovering a larger percentage of coal in place. The customary system of mining in the United States is by room and pillar, or some variation thereof, which leaves pillars of coal to support, the roof. In many operations, where the pillars are not systematically recovered, the loss of coal often amounts to 50 percent or more of the original deposit. In many instances in developing new mines, It is planned to recover chain and barrier pillars on retreat when the mine has reached established boundaries. Too often, however, mines are abandoned for some unforeseen reason before completion of mining without recovering any pillars. Usually, these pillars are lost forever. With this in mind, the Mining Division, Region VIII, of the Bureau; of Mines is encouraging mining by longwall methods. It is a generally known fact that almost all of the European coal is mined by longwall methods, which are conducive to a high percentage recovery of coal. A comparison between mining systems usually is on the basis of tons per man per shift. Unless all operating conditions are similar, such a comparison could be misleading. Generally, the output per man shift in European longwall mines is less than that obtained in room-and-pillar mining in the United States. In European mining, maximum recovery of coal is not only mandatory but it must be accomplished without major damage to surface by subsidence. These restrictions necessitate packing or stowing with consequential increases In manpower and decreases in output per man shift.

Jan 1, 1954

By J. P. Coughlin

The U.S. Bureau of Mines has developed a monitoring system that acquires and analyzes data for use in determining the conditions that may precede mountain bumps in coal mines. Based on a UNIX workstation linked to an array of geophones in a working longwall operation, the system captures complete waveforms of microseismic events and simultaneously obtains continuous samples of the voltage levels of each geophone. Event rates and locations are calculated and displayed in real time on the UNIX workstation, which is situated in an underground instrumentation room. These results also are transmitted from the workstation to a display computer near the longwall face. The system runs continuously and has the capability to acquire, analyze, display, and archive microseismic (transient) data and single point data, such as closure and pressure changes, simultaneously.

Jan 1, 1993

By A. L. Peyton

The Brewer mine, near Jefferson, Chesterfield County, S. C., was originally operated as a gold mine. As late as 1890 this mine was reported to have been one of the large gold producers in the southeast. Occurrence of topaz on the Brewer property was not reported until 1935, when it was discovered, by Parks3/ and Parks of the Federal Geological Survey while they were investigating gold deposits in the Piedmont province.

Jan 1, 1953