Search Documents

By Lyall Workman, Jack Eloranta

In this paper results of drill to mill research are examined. It is found that several descriptors of blasting results change when the powder factor is increased. Fragmentation shifts toward a finer distribution. The Bond work index decreases and the product of the t10 model breakage parameters increases. Both of these indicate more softening of fragments. There is research that found large differences in bond work index and other studies that find a much smaller decrease. Even at the lower decrease, however, some savings in energy cost can accrue in hard ores ground to small size.

Jan 1, 2009

By Shih Wen Wang, Ronald R. Rollins

A blast casting model is proposed to predict the burden velocity in bench blasting. This blast casting model is the first theoretical model that 1) explains the throwing procedures and mechanisms, 2) uses the explosion pressure as the primary source in throwing rock fragments, 3) applies them to field conditions successfully. Also the predicted burden velocities are based on the rock properties, the explosive properties, and the drilling and initiation patterns. This blast casting model is programmed into a computer software "ROCKFRAG". The comparisons between "ROCKFRAG" predicted values and two field test data are in good agreement.

Jan 1, 1992

By D E. Siskind

The Bureau of Mines performed a comparative study of nine sites at eight surface coal mines to determine if the presence of near-surfaced underground abandoned workings resulted in the generation of adverse long-duration, low-frequency blast vibrations. Six of the nine sites had underlying workings, and two had thick layers of low-velocity unconsolidated surface material.

Jan 1, 1990

By N Vijay Mohan, K V. Balamukund, G Ananth Ramulu

Jointing of steel rods in reinforced concrete structures needs careful consideration as it renders the structure weak at the joint. The jointing is usually done at sections of structural members, where the bending moment and shear force are least. Jointing is done either by overlapping the rods or welding or by mechanical splicing. A novel method of jointing them is by inserting the two rods in a steel sleeve and cladding it on to the rods by subjecting the sleeve to explosive energy. A rod jointed in this fashion is tested for direct tension and bending when used in a reinforced concrete beam. The test results show that it is an effective method. The advantage is that a number of joints can be made in a single operation.

Jan 1, 1993

By E W. Kohler

Geophysical wireline logging of blastholes provides useful geological data and has considerable potential to improve overall blasting control and costs. This paper uses case histories to show how logging techniques have highlighted certain problems, and discusses the various in-hole tools available. In particular, the issue of the effects of hole diameter on explosive column height,and the importance of this when deck charging is addressed. The suitability and cost-effectiveness of currently available logging technology to the wide range of blasting applications is discussed.

Jan 1, 1988

By Thomas A. Simpson, Yung-Kwaun Jow, Dennis L. Gamble

Construction of the $200 million Riverchase Galleria Mall in Hoover, Alabama was started in early 1984. The construction area consists of about 70 acres. The extensive building complex requires heavy concrete foundations which have to be poured during the early stages of construction and on a nearly daily situation so that contractual agreements can be met on a timely basis.

Jan 1, 1985

By Koichi Kurokawa, Takeo Ueda, Masahi Nakano, Yoji Tasaki

A lightning strike generates several 10kA and several billion volts, and earth currents generated by lightning is dangerous to some underground and all surface blasting operations. In order to evaluate the safety against lightning in conventional electric firing method and electromagnetic induction blasting system, a test is conducted by connecting a wire with an impulse generator. Frequency of impulse current used in the test is 17kHz and the waveform is a vibration type and the duration time is 250 ~usec. The results of the test show that induced current increases with the increasing of impulse current. In the case of MBS connection, when maximum primary current is 1700A, Maximum secondary current is 11.8A and the electric detonator is fired at this condition.

Jan 1, 1988

By Dennis A. Clark, Richard E. Calvin

As the scarcity of mineral resources increase and subsurface mining activities expand along with simultaneous surface mining in coal, industrial minerals and rocks, along with metals, the need to insure safe conditions is paramount.

Jan 1, 1981

By Ian A. Niell, Alastair C. Torrance

A joint research programme conducted by BHP Central Research Laboratories and Du Pont Wesfarmers Pty Ltd examined the effect of the size of cast primers on the run up and steady state detonation velocities of ammonium nitrate based explosives as a function of blasthole diameter. Both continuous and point to point velocity of detonation measurement techniques were used. The field trials examined a number of the Du Pont HDP series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the run up velocity of 187mm diameter ANFO charges is negligible using cast primers as small as 1509. However, emulsion and watergel explosives did exhibit run up in both 187 and 311mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blasthole diameters.

Jan 1, 1990

By Paul V. Sterk, James Wieser

Mining in underground situations requires constant change due to changing ore bodies and economics. The Homestake Mine in its 122 years of existence has gone through numerous changes due to these factors. Recent sustained low prices in gold and ore bodies that are smaller or within mined out areas have forced the mine to reevaluate how these ore blocks will be mined. This paper will describe the design, drilling, and blasting of a complex ore block using the blind raise uphole bulk mining method.

Jan 1, 1999

By Steven V. Crum, Willard E. Pierce

Concern has been raised about the adequacy of current regulatory guidelines designed to protect homes from unwanted blast damage due to low frequency ground vibrations; in particular those with predominant frequencies below 6 Hz. This report summarizes and updates the preliminary results of a continuing Bureau of Mines investigation which will be completed later in 1995. Four structures at four different surface coal mines have been studied by examining their response to ground vibrations created from overburden blasting. House response to ground vibrations with dominant frequencies down to about 3 Hz were recorded. Many of the blasts produced ground vibrations with peak amplitudes above expected crack-producing thresholds. Response motions were compared to those predicted by theoretical single degree of-freedom response models.

Jan 1, 1995

By Mark S. Stagg, Norman S. Smith, Rolfe E. Otterness, Stephen Rholl

Blast design parameters were studied in an attempt to quantify their relationship to rock fragmentation. The Bureau of Mines conducted a series of 29 reduced-scale shots at the University of Missouri-Rolla's experimental mine with bench size from 40 to 80 inches. Design parameters varied were burden, spacing, explosive diameter and stemming-explosive length. The shots had 3 or 4 blastholes fired at delays of 1-4 ms per foot of burden, based on previous tests that showed hole interaction could improve fragmentation by 12 to 20 percent over single-hole shots or simultaneous firing. All rock, 2000 to 23,000 pounds per shot, was screened and weighed to determine the fragmentation size-weight distribution.

Jan 1, 1991

By Brendan O'Reilly, Outokumpu Zinc, Geoff J. Johnston, S Durucan

Historically vibration monitoring has dealt primarily with surface blasting or "near field" monitoring of underground blasts. The Situation at Tara Mines is different, blasting occurs up to 400m underground, with a number of blasts occurring daily and occasionally with residential properties directly above the blasting site. Tara Mines, due to both its location (1.5 km from the rural town of Navan) and stringent planning conditions have always had to monitor, carefully plan and control the levels of vibration from blasting. The statutory vibration limit at Tara allows a maximum peak particle velocity of 7.62 mm/s with no frequency limitations. Levels of vibration have been monitored continuously since mining operations began in 1972.

Jan 1, 1994

By Terry Nichols, Karl E: Warkwick Burgher, Charles J. Wideman

The application of Fourier spectral analysis to records of ground vibration generated by over 100 explosions from an open pit mine is used to develop empirical predictor equations that relate the response spectra to the blasting parameters used to generate the excitation motion. Time series representations of ground particle velocity are transformed into the frequency domain where the appropriate modifications are made such that the inverse Fourier transform yields the time series representation of particle displacement and acceleration. Compensations are made for the transform function of the recording system in the frequency domain. Spectral analysis of the three types of ground motion is correlated with the blasting parameters. The results show that the frequency content of ground vibrations generated from a mine blast can be quantified in terms of the predictor equations.

Jan 1, 1990

By Dadan Munawar, Benny Gunawan

Blasting at Sebesi in Central Tutupan Pit area in South Kalimantan, Indonesia is planned to be using emulsion, where used oil makes up 50% of the total emulsion fuel. The significant amount of used oil from various mining operation units had been of deep concern since it might be reused to implement environmental programs by substituting 50% of fuel with used oil in emulsion, thus decreasing fuel consumption and increasing efficiency by reducing fuel cost. Used oil must pass laboratory test to meet the Indonesian National Standards (SNI) No. 7642:2010 of used oil specification. Other considerations include the location which is adjacent to the mine office facilities with a radius of <1,750 meters (5,741 feet). Thus, appropriate methods must be performed to meet the SNI No. 7571:2010 of vibration threshold in order to implement safe blasting technique and prevent potential damage.

Jan 1, 2015

By Yonghun Jong, Chungin Lee

The main purpose of this study was to apply the artificial neural network (ANN) models to determine optimal powder factors and predict peak particle velocities, based on a series of observations and input parameters. The used blasthole pattern was V-cut. The locations of blastholes and ignition patterns remained almost constant. The input parameters were 14 geological conditions (i.e., dip, dip direction, spacing, separation, and persistence of 2 discontinuity sets, tunnel orientation, rock strength, RQD, and RMR) and 4 blasting conditions (i.e., distance between blasting points and measuring points, charge weight per delay, drilling length, and blasting efficiency). Data for the ANN application in this study were recently collected in a highway tunnel under construction in Korea. The main rock type in the site was biotitic granite. An optimum ANN model was determined by training models with collected data. The trained model was used to evaluate the prediction capability of the optimum model. It was shown that the ANN model could predict the powder factor and the peak particle velocity depended upon the selected input parameters. Particularly, the ANN model predicted more accurate peak particle velocities than those obtained by the blasting vibration equation. Moreover, the more dominant factors among the input parameters could be determined by analysis of the relative strength effect.

Jan 1, 2002

By Gour Sen, Peter Bellairs

Blasting conducted in rock temperatures greater than or equal to 55°C (13 1 “F) and / or in rock containing sulphide minerals and their oxidation products can result in unplanned detonations. Blasting practices involving the identification of the affected areas together with the use of speciality explosive products and rigorous attention to quality control are required to safely blast in these types of environments. Sulphide dust explosions occur in some underground mines where the primary blast results in a secondary explosion of the sulphide rock dust which propagates some distance from the primary blast area. This phenomena results in considerable damage and the generation of significant volumes of toxic gasses delaying re-entry to the affected area of the mine thereby increasing both costs and safety concerns. The exothermic reaction between ammonium nitrate based explosives and rock types containing partially oxidised sulphides have resulted in numerous high risk blasting incidents. These reactions can occur at ambient temperatures and often result in premature detonations / deflagrations causing a great deal of consternation at the affected minesite resulting in lost production and considerable expenditure to solve the problem. Rock masses at elevated temperatures can also result in unplanned detonations unless appropriate precautions are taken. This paper discusses each of these hazards, cites some case studies and details appropriate generic safe and efficient blasting techniques for each of the above applications using appropriately formulated explosive products.

Jan 1, 2000

By Callie Covert

This paper describes the application and results of a more efficient method of breaking boulders using dynamite and water. This method is being used for the disposal of boulders that result from pinnacle and cap rock remaining after blasting on highways and job sites. This method is a faster and less expensive use of dynamite to reduce oversized boulders than the conventional rock hammer. The problem with excessive fly rock has been substantially reduced when using this technique over traditional methods.

Jan 1, 2001

Coal strip mine operators in Western Canada often mine steeply-dipping multiple coal seams in mountainous terrain. The ability to fragment the rock waste layers above and below these seams with minimum disruption of the seams in large blasts normally involves decked charges in large rotary boreholes. Mining these seams may take two or more separate blasts to break the waste wedges above and below the coal, but these wedges can be blasted in a single shot for better mining efficiency.

Jan 1, 1985

By E Emery Jr Gray

The City of Richmond, in an effort to improve sewage treatment facilities, designed an invert syphon to cross the James River at Fulton Bottom. The design criteria called for installation of two 36-inch pipe' lines at an elevation of -35 with the mean water level being at elevation 00. This paper discusses the actual method of construction used to blast the river bottom. Choice of excavation equipment, nature of the river, as well as the geological structure, were taken into consideration.

Jan 1, 1979