Search Documents

By Walters GW

A countercurrent method of metal refining using crystallization and reflux is discussed. 4n account is given of the development of this technique for the separation of silver and bismuth from lead using bench-scale studies to the present small pilot-plant unit (around one tonne per day) in the "Commonwealth Scientific and Industrial Research Organization (CSIRO)" Division of Chemical Engineering.

Jan 1, 1975

By Smith PE

The main components of face design are the power loader, face conveyor and powered support system and the interaction of these components determines the effectiveness of strata control. A major influence upon the interrelationship of this equipment is the geological environment, of which seam thickness appears to play an important role. Recent thick seam experience indicates a significantly different characteristic behaviour pattern from that observed in thin seams The structural integrity of the face wall is particularly influenced by seam discontinuities such as natural joint planes and mining-induced fractures in the yield zone ahead of the faceline. In addition, the presence of stone bands or dirt partings in the seam offers interfaces for uncontrolled release of blocky material. Some case study experience at British collieries provides a comparison with performance data at a specific location, that highlights the importance of coal face layout and design.

Jan 1, 1986

By Hara Y, Arino S, Nakamura M, Tachimori M

The theoretical and experimental studies have been done to clarify the hearth flow of iron and slag. The results of dissections show that the hearth can be treated as a packed bed of coke hav- ing good permeability with a coke-free layer at the bottom of the hearth. 3-dimensional numerical calculations of hearth flow with and without a coke-free layer are carried out, and the results are assured by a water model simulation. The influences of a coke-free layer on the iron flow and the discharge route of iron and slag are examined. The 3-dimensional flow pattern can be represented simply by the travelling time, which depends on characteristically the profile of coke-free layer and the quantity of iron in the hearth. Those flow parameters could be obtained by the results of radioisotope tracer test ( Co for iron flow, and Sc for slag flow) at several furnaces. As a result, it is found that the coke-free layer repeats the cycle of appearance and disappearance at several-month intervals. This cycle corres- ponds to large temperature fluctuation at the bottom of hearth. The relation between iron flow and skull (solidified iron, coke and deposited graphite mixed layer) on the hearth brick was studied by the model experiment and the thermal analysis based on the indications of thermocouples installed in the bottom of the hearth. If a thin coke-free layer is formed on the skull, a fast iron flow is generated in the layer, and melts away the skull. The growth and melting of skull produces the fluctuation of thermal load on a bottom brick, causing brick Damage.

Jan 1, 1981

An effective production control system should maximise recovery of economic material from the resource. To do this, internal waste must be accurately delineated and efficiently removed. Achieving this is most difficult in low grade blocks just above and just below the cut off grade, where ore:waste separation follows assay or statistical, rather than geological boundaries. Difficulties arise from sampling errors, configuration of the economic mineralisation, and local variations in geology. Mine bench parameters and mining equipment size apply further constraints to the actual field separation of the ore from the waste. At BCL, management of the resource starts with an effective orebody model for planning, scheduling and ore:waste prediction. Ore production from each mining location is reconciled with concentrator tonnage and grade, and the reconciled grades are compared with the planning orebody model to highlight any Differences.

Jan 1, 1986

In the five years since Great Central Mines Limited (GCM) commenced exploration in the Jundee and Bronzewing areas of Western Australia's Yandal greenstone belt, the Company has been transformed from a junior explorer into Australia's fourth largest gold producer with annual production of approximately 440 000 ounces and mineral resources of seven million ounces of gold.The growth in resources has been driven by a high quality geoscientific approach, supported by a substantial budget for drilling and strong management commitment. In 1997, the Company expects to spend US$30 million on exploration in the Yandal greenstone belt.

Jan 1, 1997

By L Terrusi

The Bungaroo Valley hosts a concealed Tertiary channel iron deposit (CID) along a 17 km stretch of its length. Bungaroo Valley is approximately 0.5 km wide upstream at its easternmost extent, and 3.5 km wide downstream where it joins the Jimmawarrada Creek. The valley follows the axial trace of an anticline that plunges gently to the southeast, and the CID infills the valley. Mineralisation extends to a depth of 230 m below the surface, and almost the entire deposit occurs below the water table. Bungaroo Valley cuts through the Buckland Hills and is bounded to the north and south by steep scarps capped with the resistant Dales Gorge Member of the Brockman Iron Formation. Basement rocks are believed to be mostly Wittenoom Formation shales and dolomites, with Mount McRae Shale and Mount Sylvia Formation also present. Deep, localised depressions appear at the base of the CID sequence towards the north edge of the upstream section of the valley, while downstream the basal CID contact is relatively flat and shallow. In both cases the profile of the CID surface closely mirrors that of the basal contact. The localised depressions seen in the upstream basal CID contact produce significant variations in CID thickness of up to 100 m over short strike distances. This uneven palaeotopography is most likely due to eddying and waterfalls forming within the riverbed prior to CID deposition during a time when the water table was much lower than at present. It may also be associated with possible karsting in an underlying dolomite unit and subsequent syn- or post-depositional collapse of the overlying CID. The irregular basal contact of the Bungaroo CID sequence has implications for mining in terms of pit design and resource accessibility.

Jan 1, 2007

The LeadtZinc Concentrator at Mount lsa treats all the lead-zinc-silver ore from the Mount Isa Mine and some of the ore from the Hilton Mine. This concentrator was commissioned in June 1966 and total lead-zinc-silver ore treatment was transferred from the Mount rsa's original No 1 Concentrator in May 1967. Plant capacity is around 5 x 106 t/y.There have been three phases of major plant modifications since commissioning:1. replacement and upgrading of the flotation section in 1979; 2. upgrading of the crushing plant and installation of a heavy medium hydrocyclone plant in 1983 for ore preconcentration, and; 3. doubling ball milling capacity and a further upgrading of the flotation section in 1992.Other developments have included the installation of flotation columns and Jameson cells.The evolution of milling practice since 1955 has been reported by Davey and Slaughter (1970), Bartrum, Dobrowolski and Schache (1977), Fiedler and Munro (1984) and Espinosa-Gomez el al (1989).Lead concentrate is smelted in Mount Isa while zinc concentrate and bulk concentrate (locally called Low Grade Middlings or LGM) are railed to Townsville and shipped to custom electrolytic zinc plants and ISP smelters.

Jan 1, 1993

By Andersen AK

As part of a research program sponsored by Continental Copper and Steel Industries, Inc. (cos), investigations have been conducted by the Colorado School of Mines Research Foundation, Inc. to study the effect of high current densities on electrolytic processes. The importance of high current densities has long been recognized, particularly in the deposition of copper, and the results of considerable research on the subject have been reported in recent years (19 29 39). This is not surprising because, besides plant capacity, current density is the other major factor which will determine the process economics. In the production of electrolytic copper, current efficiency, steam consumption, number of cells, building area, metal inventory, cathode purity, and power consumption are all affected by current density. The ability to maintain a high current efficiency and satisfactory cathode purity while increasing the current density to twice or three times that commonly practiced could result in considerable saving of capital investment and reduce the operating cost per ton of metal produced. The optimum current density i.e., that current density of which production cost would be at a minimum, can be established from an analysis of the various inter- relating factors (49 59). A review of.all operating electrolytic plants (electrowinning and electrorefining) will indicate that most of these plants are operating at 50% or less of the optimum current density (6). One of the reasons for not using the optimum current density may be attributed to the fact that conventional electrolytic tank- house equipment does not perform satisfactorily at high current density operations. Various investigators (19 79 8) have attempted to overcome this limitation by modifying the design of the electrolytic cell, virtually unchanged since it was first introduced in the late 1800's. Previously, these attempts have not resulted in,a cell design suitable for commercial application. However, recently, a cell has been designed which performs efficiently under such conditions. This is a CCS development (patents applied for).

Jan 1, 1969

By D K. Miller, L W. Armstrong

In April 2006, Orica Quarry Services undertook an investigation to determine the likely vibration and frequency response of three water storage tanks to quarry blasting, immediately adjacent to the tanks. Of the three tanks that were studied, two are relatively tall with a æwineglassÆ shape; one is constructed of steel (4 ML storage capacity) while the other is constructed of concrete (2 ML storage capacity). The third is a ground-embedded concrete tank that is relatively squat and broad in shape (38 ML storage capacity). A vibration limit of 25 mm/s and an acceleration limit of 0.16 g were imposed on the tanks. However, this report shows that this acceleration limit, whilst having relevance to low frequency earthquake motions, is quite inappropriate for the high frequency blast vibrations that are typical in a quarry blasting environment. The investigation involved firing 11 single blastholes of known charge weights and distances from the tanks, and measuring the tank vibration response using blast monitors placed on and around each tank. Analysis of the data collected from the cement tanks showed resonant responses over a broad range of frequencies, with dominant and lesser responses in vertical and lateral motion recorded at 9.8 Hz, 12 Hz, 16.8 Hz, 17 Hz, 31.3 Hz and 38.1 Hz. Unfortunately, most of the data collected on the steel tank was corrupted by noise due to electrical sources and/or mechanical sources such as the water agitator inside the tank. Advanced Monte Carlo vibration models were then constructed using the single blasthole information. Knowing the resonant frequencies enabled the modelling of electronic delay sequences for the reduction of resonant vibrations. Ultimately programmable and accurate electronic delay detonators were deemed essential to allow blasting in relatively close proximity to the tanks while avoiding resonant frequencies. Three blast designs were modelled, ranging in maximum instantaneous charge (MIC) from 4 kg to 22 kg, and 60 holes to 160 holes. The modelling showed that two of the designs (using small charge weights) could be used no closer than 71 m from the storage tanks. This is based on a 90 per cent confidence level of achieving vibration levels within the 0.16 g acceleration limit, even though the velocity levels predicted to be generated at this distance were significantly less than the 25 mm/s limit. The third design incorporated larger charge weights and could be used for blasting at distances no closer than 220 m from the tanks. The present work, conducted in an operating quarry, demonstrates the usefulness of Monte Carlo waveform superposition techniques for the control and reduction of ground vibration (either velocity or acceleration) under restrictive environmental constraints. However, a discussion is also presented to demonstrate that it is somewhat restrictive to impose an acceleration limit based on the motion produced by low frequency earthquakes rather than the motion produced by high frequency blast vibrations.

Jan 1, 2007

By Rigby D, Gould K. W, Hart G. H

The variation in chemical and isotopic composition of hydrocarbon gases generated from humic source rocks in the Cooper Basin, the orth West Shelf, the agoorin oil shale deposit. ollinsville and the southern Sydney Basin is reviewed, discussed and interpreted.The primary composition of gases generated in and released from such source rocks appears to be very largely controlled by the degree of dispersion of the organic material. For example in eoaly shales, where the degree of dispersion may be high, products as generated may escape into surrounding inorganic structures where further maturational reactions may proceed. On the other hand, when the organic materials occur in massive form, as in coal seams, the hydrocarbons generated tend to be retained within the coal. Further cracking to the stage of methane generation is usually required before release of hydrocarbon products is significant.Secondary factors of importance in determining seam gas composition in the Bowen (Collinsville) and southern Sydney Basins are the invasion of coal measures by carbon dioxide from external magmatic sources and/or the vertical diffusion and loss from the surface ofgases generated at depth.Isotopic measurements of gas composition have been particularly valuable in determining the origins and histories of the gases examined, in demonstrating when gases are of mixed origins and in the prediction of gas quality in exploration.

Jan 1, 1985

By Anderson K

In 1991, the first horizontal raise drill hole in Australia was successfully completed by Australian Raise Drilling Pty Ltd (ARD) at the Perseverance nickel mine of Western Mining Corporation's (WMC's) Leinster Nickel Operations in Western Australia. At that time, WMC were experiencing considerable difficulties in developing the horizontal drill drives through the orebody using conventional drill and blast techniques. Following the success of the initial hole, a further two holes were drilled as part of the evaluation program. The technique has proved so successful that it has been accepted by WMC for on-going development of drill drives at Perseverance.This paper describes the program. It relates how the project evolved, the modifications that were required to the equipment used, the performance experienced during the program and the future of the method in this and other applications.

Jan 1, 1993

The mechanisms of fragmentation in homogeneous materials and structured rock mass are reviewed. A method previously used to predict vibration damage to the remaining rock is extended and shown to be valid for the prediction of fragmentation in the rock mass removed by blasting. The effectiveness of different explosives in different types of rock blasting is discussed.

Jan 1, 1990

Base metal skarns have provided most of South KoreaÆs Pb-Zn production since the end of the Korean War, with the bulk of production coming from the Yeonwha group of mines. Currently only the Kumho Zn-Pb mine remains in production, while magnetite skarns are mined as iron ore at the old Yomisan and Ulsan base metal deposits. Base metal skarns within Korea fall into two groups; those hosted in Cambro-Ordovician limestone sequences, situated mainly in sub-basins in the northeast of the peninsula and those hosted within carbonate volcaniclastics of the Cretaceous Gyeongsang Basin, in the southeast. Sulphide mineralisation is dominated by sphalerite, lesser galena, arsenopyrite and pyrrhotite, with subordinate chalcopyrite and molybdenite with Ag-Co credits. Skarns are composed of pyroxene-clinopyroxene-garnet-carbonate-quartz and magnetite, grading into silica-chlorite hornfels. Most of the significant deposits display both pipe-like and stratabound morphology. In the Hwanggang district, a zoned distribution of Ordovician carbonate hosted, polymetallic Mo-W and Zn-Pb-Cu-Ag base metal deposits is observed around the margin of a Cretaceous granite intrusion. Similar polymetallic zoning is recognised in the Sangdong district, where deposits include Sangdong (W), Abisan (Au-As) and Yomisan Northwest (Zn-Mo) and Yomisan Southeast (Zn-Cu-Co), hosted in Ordovician carbonates in proximity to Cretaceous quartz porphyry intrusives. The Taebaeksan district hosts the largest deposits at the Yeonwha group of mines. Although production ceased in 1993, significant resources remain, hosted in Ordovician limestone and dolomite that have been intruded by Cretaceous quartz porphyry dykes. Deposits in the Cretaceous Gyeongsang Basin consist of bedding concordant, vertically stacked base metal skarn mineralisation at several stratigraphic horizons, connected by carbonate-base metal veins with a pipe-like geometry. Evidence such as massive sulphide layers and restricted proximal carbonates suggest mineralisation was initially partly syn-depositional, with both base metals and carbonate venting onto a lake floor, being reconstituted to skarns by later magmatic activity. Skarn mineralisation is universally closely associated with the Cretaceous Bulgugsa Series acid intrusive activity. A common intrusive-structural relationship is recognised at some deposits, with bedding plane and imbricate thrust faulting, introducing felsic intrusives as sills. These intrusions probably introduced the base metals, carbonate, boron, heat and silica, which metasomatically reconstituted the carbonate lithologies to form skarn assemblages. The Korean base metal skarn deposits are regarded as Zn-Pb chimney-manto skarns and display similarities to the Mexican manto type deposits.

Jan 1, 1999

By Clift N

Lead concentrate from the Isa and Hilton lead-zinc concentrators of Mount lsa Mines Limited is smelted at Mount Isa to produce a lead-silver bullion. This bullion is cast into four tonne blocks and shipped to Britannia Refined Metals Co Ltd, NorthDeet, England and to plants in Asia for refining and marketing. The traditional treatment stages at Mount lsa are sintering, smelting, and drossing and casting, with some of the sinter plant feed being pre-treated through an Isasmelt plant.A commercial scale lsasmelt based lead smelter was commissioned in early 1991.

Jan 1, 1993

The basic flowsheet for the Kalgoorlie Nickel Smelter and Kwinana Nickel Refinery are discussed in relation to the mineral components of Kambalda produced nickel concentrates. Both processes handle violarite and pentlandite satisfactorily but the smelter has limitations where high copper recovery is required and in its ability to handle magnesia containing minerals. While the latter can be more economically handled at Kwinana the limitations of this tolerance are discussed together with problems arising from treating pyrrhotite, pyrite and precious metals by the Sherritt Gordon process.

Jan 1, 1973

Mssissippi Valley-type (MVT) and sedimentary-exhalative (SEDEX) zinc-lead deposits represent about half to three-quarters of the world's production and reserves of lead and zinc. The two deposit-types have traditionally been regarded as separate entities in terms of genesis largely because they possess very different morphologies, resulting from the epigenetic nature of MVT deposits and the syngenetic origin of SEDEX deposits. Similarities in regional setting, metal ratios, size and grade, lead and sulphur isotopes, and source(s) of fluids and metals in the two deposit-types, however, suggest that they could be products of similar genetic processes. The physical properties of MVT ore fluids suggest that certain types of SEDEX deposits could have been formed from fluids possessing similar salinities and temperatures. The hypothesis is further strengthened by the facts that: 1. in several cases MVT and SEDEX mineralisation occurs in the same region, and 2. recent advances in establishing the timing of MVT mineralisation has revealed that some MVT deposits are contemporaneous with nearby SEDEX deposits. If MVT and SEDEX zinc-lead deposits do indeed share a common ultimate derivation from fluids that emanated from sedimentary basins, then the presence of one deposit-type in a region could be used to infer the possible presence of undetected deposits of the other type. Furthermore, knowledge of the mineralisation age of one type will constrain the exploration target host rocks of the other type. A genetic relationship between MVT and SEDEX mineralisation may also explain why certain individual deposits, such as several in Ireland and eastern Canada, appear to be 'hybrids' and possess geological attributes of both end-member types.

Jan 1, 1993

By Szymanski J, Planeta S

For many hard rock mines with near surface deposits, the surface crown pillars form the first line of protection for the immediate underground workings. Underground stopes are typically contained by crown pillar, which protects the level above, rib pillars, and a sill pillar through which the ore collection system is cut. This paper discusses the mining of these pillars, with particular emphasis on the overall stability of the mined out upper part of the mine areas. An area of interest is located in the Canadian Shield, where the mining has progressed below four thousand foot level in the ultramafic high grade sulphide type of orebody.

Jan 1, 1995

In 1972, metallurgical testwork on Renison ore indicated a significant proportion of low specific gravity, tin-barren material ideally suited to heavy medium separation (HMS). Further technical and financial studies provided adequate economic justification and in December 1974 the Renison HMS plant was cannissioned. Initial operations were interrupted by the imposition of tin production quotas for three months in 1976; they were also beset with difficulties particularly with regard to mechanical wear. During the first two operating years much develognent work was carried out including installation of a pyrrhotite flotation bank in the medium recovery circuit, investigations into various wear-resistant materials and the use of atanised rather than milled ferro-silicon. By 1977/78 financial year satisfactory performance had been achieved and since then the average floats rejection has been 18.8% of the total ore treated with an associated tin loss of 2.96%. Developnent has nevertheless continued during the last three years, principal modifications being the installation of larger aperture desliming screens and improvements to the overdense cyclone circuit.

Jan 1, 1978

Cable bolts are being used more extensively by the mining industry for many different rock reinforcement applications. The configuration of these bolts has evolved over the last 20 years to meet the immediate needs of industry at the particular time. Most improvements to date have focussed on increasing the mechanical performance with little attention given to issues such as ease of handling, matching response to that of the rock mass or corrosion protection. Ultrastrand has been designed and being developed with this broad perspective in mind so that it will satisfy the ground reinforcement needs of today's and tomorrow's mining industry.Laboratory tests on Ultrastrand prototypes have confirmed that mechanical performance is superior or equivalent to Standard and Birdcage Strand respectively. Preliminary discussions have been held with an installation equipment manufacturer with a view to conducting a trial at a mine site by early-1992.

Jan 1, 1992

By Wallman D

Since 1981 two single entry roadways have been driven at Ellalong Colliery for a total distance of 1 030 metres. They were driven at a height of 1.73 metres within the 3.7 metres thick Greta Seam using a Dosco In-Seam Miner (I.S.M.). Ventilation of the drivage was accomplish- ed by an exhausting fan in series with steel ducting and flexible ducting in the immediate face area. The air quantities provided at the face were more than adequate to comply with the requirements of -the auxiliary fan rules and the Coal Mines Regulation Act, 1912, as amended. The experience gained in these drivages demonstrated that the ventilation of long single entry headings can be practically and safely achieved using existing equipment.

Jan 1, 1983