Search Documents

By B C. McLellan

The decline of ore grades on land, increasing demand and high prices for various minerals have led to an increased interest in mining the deep ocean sea floor. The potential deep ocean reserves are vast and in some circumstances the grades are high enough to consider mining. However, the consequences of such mining are as yet uncertain. This paper will present the results of a comparative assessment of life cycle impacts of deep ocean minerals. Two alternative extraction technologies from different deep ocean resource types were examined and key commodities are considered. Initial results indicate that the energy requirements will be higher than the average land-based resources, but may fall within the range of the deepest terrestrial mines.CITATION:McLellan, B C, 2015. Comparative life cycle impacts of deep ocean minerals and land-based counterparts, in Proceedings Third International Future Mining Conference, pp 253–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

THIS paper deals with the handling of the various materials used in the 100-ton zinc plant at Risdon, and, in view of the magnitude of the works, the configuration of the ground covered by these works, the variety of the rnaterials used, and the large quantities, a very attractive and interesting subject is opened.The works are situated on the right bank of the River Derwent, about four miles above Hobart, the capital city of Tasmania. The Risdon works cover a space of 149 acres, the area being :3800 yards long by 2800 yards wide, and the elevations vary from 6 ft. above high-water mark at the wharf and foreshore to 163 ft. above high-water mark at the power station, these being the limiting points as regards elevation which are considered in this paper. Throughout the paper elevations are given in feet above high-water mark. Fig. 1 shows a general view of the works taken from the opposite bank of the River Derwent. The wharf is clearly shown, with SS Kekerangu loading residue; behind the wharf is seen the inclined conveyor leading to the cakine bin; further up the hill is the leaching division. No. 1 haulage runs to the left of this up to a point on the left of the power station, the large reinforced concrete building at the top of the hill. Below this is the cell room, the largest building on the plant. The roasting division, not very clearly seen, lies at the foot of the main stack, and the casting division lies to the left of this, between the leaching division and the cell room. A large wharf has been construl'ted alongside the works. This wharf is 880 ft. long and 60 ft. wide. It is capable of berthing large overseas steamers, as at low tide there is a depth of :30 ft. of water. The rise and fall of the tide at the wharf is 4 ft. 6in., and the river is navigable at all states of the tide. Just above the company's wharf...

Jan 1, 1923

By T Medhurst

Recent developments in geophysical borehole log analysis using the Geophysical Strata Rating (GSR) are now routinely used in a number Australian coal mining operations. This allows development of 3D geotechnical strata characterisation models for a range of purposes. The availability of this data provides a means to identify relationships between ground conditions and ground behaviour. As a result, several new design methods have been developed to assist in the strata management process such as roof support, longwall shield design and shaft stability assessment. This paper outlines these methods and provides examples of their application. CITATION:Medhurst, T, 2018. Geotechnical strata characterisation using geophysics and its application for coal mine design, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 420–433 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By R Markoski, P Grealish

The requirement for rapid vertical development for underground ventilation is often a factor when dealing with dynamic mine plans, with short vertical developments being used to optimise ventilation systems. In an effort to increase the safety and efficiency of the constructions, a simple and effective sinking methodology is required that is both adaptable and repeatable. A modified shaft construction methodology is proposed that attempts to minimise risk to the personnel as well as be cost-effective. Readily available equipment is used to ensure adaptability to the various environments and shaft parameters.One of the greatest risks of shaft sinking is having personnel working suspended over open cavities or underneath suspended loads. Removing this risk, by ensuring all construction is done from solid ground, allows for safer sinking operations. As the process is repeatable, familiarity and confidence in its construction sequence will increase with each successive sink.A trial sink is performed with a 3.6 m diameter, 20 m deep shaft. The shaft was excavated using a conventional strip-and-line philosophy, with the shaft then being lined from the collar via the use of large diameter corrugated steel culverts. The annulus between the steel culverts and shaft excavation is then filled with a concrete mixture to secure it in position.The new process was successful, with no personnel at any time during the process being suspended above an open excavation. The installation had relatively low capital and operational costs and was completed faster than an equivalent, conventional concrete-lined shaft construction. Therefore when compared to conventional shaft-sinking methods, this process can be considered safer, more efficient and relatively cost-effective.Further research is required to determine whether this method can be expanded to larger vertical developments.CITATION:Markoski, R and Grealish, P, 2014. A new method for rapid vertical development of underground ventilation shafts, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 603–606 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Y Zhu, D J. Williams, M O’Neill, C Zhang, X Lei

A cover of inert material overlain by topsoil is required over compacted, seawater-neutralised red mud, a waste product from the refining of bauxite to produce alumina. The cover is to be revegetated, and it is necessary to demonstrate that the potential evapotranspirative-driven uptake of salts from the seawater-neutralised red mud will not impact the revegetation. An instrumented column was designed and constructed to test the evaporation-driven uptake of salts from compacted red mud into an overlying cover material with a thickness limited to 600 mm. The PVC column is 1.2 m high, with a 200 mm internal diameter. The column is instrumented with up to ten of each of moisture, suction, salinity and temperature sensors, together with a data logger, designed and manufactured at The University of Queensland (UQ) in Brisbane, Australia. The sensors were installed through the wall of the column at various depth intervals, with each set of sensors located at quarter points around the circumference of the column. Two pressure transducers were installed in the column to monitor the change of water level due to rainfall and evaporation. The column was filled with compacted red mud to a depth of 600 mm overlain by 600 mm of cover material, both sourced from the Queensland Alumina Limited (QAL) site in Gladstone, Queensland, Australia. The column is installed on a building roof at UQ, alongside a weather station, and will be subjected to the prevailing weather conditions for up to 1 year in the first instance, during which time the weather conditions and sensor responses will be continuously monitored. This paper reports on the instrumented column set-up and the early results obtained from the test.CITATION:Zhang, C, Williams, D J, Lei, X, Zhu, Y and O’Neill, M, 2018. Instrumented column testing of salt uptake from compacted red mud into a cover, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 220–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By C Boyle

Brockman 2 mine is located in the Pilbara of Western Australia and is operated by Rio Tinto Iron Ore. Mineralisation is hosted by synclines where there is structural complexity to focus fluid flow. Mineralisation is hosted by the Brockman Iron Formation. Mining is on 10 m benches and blastholes spaced at 6 - 8 m apart are geologically logged, sampled by shovel cuts, and assayed using X-ray fluorescence for ten chemical variables. Blast blocks are digitised by mine geologists to assign destinations of material within blasts. Resource evaluation drilling is on a spacing of 50 m × 50 m across known mineralisation and consists of recent reverse circulation drilling and older open hole percussion drilling. Sampling of resource evaluation drilling is by rotary splitters or riffle splitters, and assaying is by X-ray fluorescence for ten chemical variables. Ordinary kriging of resource evaluation produces a long-term resource model. This study examines whether mine planning would be improved by using a blasthole estimate to extrapolate grades into deeper benches and merging the blasthole estimate with the long-term model made using resource evaluation drilling. The two estimates are merged into one model using an inverse weighting based on kriging variance. However, reconciliation results in a test bench show the original estimate made using resource evaluation drilling more closely matches mine geology block outs than does the merged model. This is due to a local trend of more high grade and higher iron grades of high grade in the area. The blasthole estimate of deeper benches must use extrapolation and it is diffi cult to take local trends into account. In contrast, the estimation using resource evaluation drilling is mainly interpolation and is better able to handle local trends.

Jul 11, 2011

Previous studies on the blast furnace raceway zone have been undertaken at three levels of scale, namely: laboratory models at low temperature, hot models which simulate coke combustion in the zone, and tests performed on operating and dismantled blast furnaces. This paper reviews the results of this published work on raceways in order to illustrate the factors which affect the raceway shape, size and combustion characteristics. As a result of the work it has been established that raceways are influenced by blast parameters such as velocity, temperature and chemistry, as well

Jan 1, 1981

By C Fountain

Australian mining and engineering companies have increasingly been investing in the mining industry in Brazil. It is a country of enormous mineral and agricultural wealth, with a well-established mining sector. Some Brazilian mining companies and personnel have been journeying in the opposite direction. There are significant differences in the approaches to engineering between the Australian and Brazilian industries that can cause confusion for companies operating in the other country. These range from differing expectations during the various stages of feasibility studies to style of plant and contracting strategies during the construction phase of projects. Some of the differences are driven by tax regimes, labour costs, or different settlement patterns. Others are the result of different histories and pressures on the industries in the two nations.This paper describes some of the differences in approach found in the two countries and some of the reasons for them.

Aug 8, 2011

By M Oyarzún

Direct relationships between rock texture and BWi (grindability index) have been established based on geological and metallurgical information supported by optical microscopy observations, gathered from 731 samples.Each recognised rock texture is observed to be related to a certain BWi range and, this texture is also characteristic of distinct lithological subunits (recognisable at mapping scale). Therefore, this relationship may provide an important tool for early milling in situ estimation.Since each textural type is a response to rock formation conditions, the causality of the relationship between BWi and texture is based on such conditions and, particularly, on the interfacial free energy among its components.According to the abovementioned textural features, the greater the free interfacial energy between mineral components, the greater the necessary energy required to break its grain boundaries and, consequently, the greater the necessary energy required for milling.If the textural evidence indicates that the rock was able to adjust the shape and/or size of its components – in a natural tendency of all systems to minimise energy– then the necessary energy required to break its grain boundaries will be lower.

Sep 5, 2011

By C Quirion

Agnico-Eagle Mines Limited, Laronde Division, operates the deepest single-lift shaft in the western hemisphere. The initial Penna hoisting plant was designed for a production rate of 1800 tonnes per day (t/d) from a 2240 m deep shaft. Exploration success, while sinking the shaft, led to a decision in 1998 to increase the production rate to 4500 t/d of ore from a loading depth of 2200 m. The new production rate was achieved by increasing the size of the rope and reducing the rope static factor from the existing 5.0 required by regulation to a static factor using the formula 25 000/(4000 + L) contained in a draft document that would eventually become SABS 0294 in South Africa. The formula permits Laronde to use a static factor as low as 4.0. The upgraded Penna hoisting system is the first hoisting plant outside of South Africa to meet the South African requirements. This paper describes the conversion of the hoisting plant to the lower rope selection factor in the year 2000 and the operating and maintenance issues experienced since then.

Jan 1, 2005

By N Maistry, C Carelse, A Singh

Banded Iron Formations or more commonly known as BIF are sedimentary rock formations with alternating silica-rich layers and iron-rich layers that are mainly composed of iron oxides (hematite and magnetite), iron-rich carbonates, and/or iron-rich silicates. Considering the depletion of highgrade iron ore reserves in South Africa, there is a need to maximise resource utilisation through the exploitation of low-grade/uneconomic resources particularly BIF material, which makes up more than 65 per cent of current reserves. Previous test work conducted by alternative BIF sources globally indicates the need for fines processing in order to produce a concentrate. South African BIF however is amenable to coarse and fines processing producing an on-grade product or blended feedstock. C-Type material within South Africa’s Northern Cape Province grading at approximately 33 per cent Fe was supplied for research purposes. Top size optimisation via gravity Heavy Liquid Separation (HLS) tests was conducted. The laboratory results being perfect separation (Ep=0) were modelled to predict pilot performance, the results of which were tested on a pilot scale for the finest size fraction (-1 mm). It was observed that a top size of -2 mm provided optimum results in terms of upgrade and recovery, with crushing finer not necessarily producing superior results. At a target grade of 60 per cent Fe, recoveries of 65.6 per cent were achieved on the laboratory scale, whilst recoveries of approximately 58 per cent were achieved on the pilot scale. Targeting higher upgrades of 63 per cent would inevitably result in lower recoveries of 57.2 per cent on a laboratory scale and approximately 54 per cent on a pilot scale. This is in line with grades and recoveries achieved globally for BIF material albeit at finer grind sizes.

Sep 18, 2023

By H Esterhuizen, W Hartman

Rockfalls or significant deterioration of mine openings can have significant safety and financial impacts for mining operations. The failure of drives in underground mines sometimes highlight deficiencies in the mine risk management systems in detecting geotechnical hazards and to prevent events that can have significant impact. Consequences from these failures includes fatalities, injuries, loss of revenue, additional cost, and potentially a loss in Ore Reserves. Where the impacts are severe, it also affects families and communities linked to the operation. The assessment of underground excavations requires consideration of the full range and spectrum of geotechnical hazards, design aspects, ground support, layouts and sequences. Where the assessment of these are insufficient or incorrect, it can result in drive failures. Care must be taken that meeting production targets and personnel pressures do not result in a situation where production take preference over a proper risk-based assessment of the drives to be mined. The risk management approach is now widely accepted in the mining industry for the control and management of risks in underground mines. Codes of Practices (COP’s), Ground Control Management Plans (GCMP), Principal Hazard Management Plans (PHMP’s) and technical guidance documents has become the norm for describing the mines main hazards, risk levels and intimating controls for safe passage of vehicles and mine personnel. However, where there is a disconnect between these documents and what is actually being done at the mine site, the COP’s and/or Management Plans become ineffective (or vice versa). This disconnect may occur due to the actual content of these documents, a lack of resources, or a lack of understanding about the implementation. There is therefore a need for sites to have a documented and implemented risk-based approach for assessing underground mine development. This approach or system needs to identify all hazards and other factors affecting mine development stability early on in the design process, and outline the risk classification and controls required. This paper presents an amalgamation and modification of previous processes for a Geotechnical Risk Management System for Underground Mine Development. CITATION:Hartman, W and Esterhuizen, H, 2018. A geotechnical risk assessment tool for underground mine drives, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 235–253 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By C K. Boafo, J Visser

Obuasi Mine in Ghana, with more than 100 years of mining history, developed from a surface operation into a deep >2000 m underground gold mine. The challenge is to extract value from narrow veins left after extensive mining in the wider ore zones of the mine. Since the merger of AngloGold and Ashanti Goldfields in 2004 the mine strives to achieve optimum extraction through an integrated Mineral Resource management process from geological modelling, resource evaluation to mine design and scheduling. The shear hosted gold deposit displays complex secondary shears of variable thickness and continuity. There is an ongoing process of changes taking place in the way that geological modelling and resource estimation is done. Recent developments include the use of computerised systems that support the whole resource management chain from resource modelling to reserve optimisation. The change in thought and technology now allows for targeting narrow veins previously ignored in optimisation and mine design since moving into mechanised mining. The increased knowledge and confidence in the resource models now allows for flexibility in mine design, selection of mining method and scheduling and extraction of the reserves. The focus area for change is the way the orebody is evaluated and extraction designed. Since 2005 major changes were made to the process. This paper considers the historical approach of resource management. It looks at the individual process changes and qualifying the way ahead.

Jan 1, 2008

By M Berry

Consider these four questions:What is the definition of life-of-mine?When should life-of-mine planning seriously commence?When can life-of-mine planning seriously commence?What is the key input to effective life-of-mine planning?Whilst there is likely to be general consensus on the answers to the first three questions, the answer to the fourth question is open to debate. This author argues that understanding and managing risks and opportunities associated with geological uncertainty is the key input to effective life-of-mine planning, at all stages in the life cycle of a mining project.CITATION:Berry, M, ?2014. Effective life-of-mine planning by understanding and managing risks and opportunities associated with geological uncertainty, in Proceedings Life-of-Mine 2014 , pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

This paper aims to address the issue of the public's image of the extractive minerals industry. What is it about the industry that incites such negative feelings and are they justified? Are we really the 'rapists of the land' that many would have us believe? Has the industry really not improved since the old gold boom days?   I believe that the fundamental cause for the public's view is lack of knowledge and understanding of the industry as a result of the dislocation of the end production from its source. There are few people who look at a house, car, record, toilet, tooth-brush, bottle of coke or pair of glasses and see the mine site that supplied the source material. But the mine site and its products should be inseparably linked. This is one area where we should be educating the public û it is all very well being anti-development but the population as a whole is not really prepared to live without its 'mineral'-derived necessities. It is very easy to say that we do not want minerals development in New Zealand but are we prepared to live with the consequences, ie go without its products? We have a duty as a global citizen to develop our own resources rather than expect Third World nations desperate for overseas investment, often with governments who are not prepared to constrain or control their development, to be exploited. New Zealand is not the only 'beautiful' place in the world and we should be aware of the impact that our demands for resources have on the countries who supply us. We have a duty to be a good global citizen.   So how does the industry improve its public image? The key here has to be to educate. This does not have to be high powered or expensive but can be as simple as getting a few local kids' hands dirty panning, and gaining some firsthand knowledge of the industry. The industry also needs to be more pro-active in the public arena. Yes, the industry has skeletons, but the industry should be publicly displaying them û admit that things have gone wrong but let's do it ourselves and not leave it up to the environmental groups to accuse, point the finger and put the industry under public scrutiny. The industry should also be publicising its successes, inviting the local press, councils, etc to view the latest area rehabilitated. But more than anything else we must tell the public what the minerals industry means to New Zealand. Can they really live without us?

Jan 1, 1991

By T P. Medhurst

In many cases mine design is the most important driver of the profitability of a mining project, however to reach an æoptimumÆ mine plan many compromises have to be made. Some of the fundamental profit (and loss) drivers relate to stoping methods and stope design parameters. Inevitably trade-offs have to be made between the stability of underground openings, ground support costs and production efficiency. This paper looks at the role of geomechanics in the mine planning and design process. The concepts of æcontrollable lossesÆ and æuncontrollable lossesÆ are developed as a means of partitioning ground control costs. A stope design example is given which provides a method of examining mining costs, and includes a decision making element in order to quantify geotechnical impacts and select stope dimensions. The method also provides a general framework as a means of balancing ground control costs against maximising returns from an underground mining project.

Jan 1, 2000

By C J. Unger, T Baumgartl, C J. Bond, P Sabourenkov, V C. Glenn

Social licence to mine is influenced by society’s perception of the mining sector’s ability to effectively rehabilitate mined land and for governments to appropriately regulate that process for the broader community benefit. In Queensland, Australia, many mine rehabilitation personnel working for active coalmines, as either staff, consultants or contractors, belong to the Central Queensland Mine Rehabilitation Group (CQMRG). The CQMRG was established 23 years ago with the aim of sharing informal knowledge related to practical aspects of rehabilitation in order to leave as positive a legacy as possible from mined land. This voluntary group of professionals also includes members from regulatory agencies and civil society. Within the dynamic regional mining environment, mine rehabilitation professionals benefit from sharing their informal knowledge.CQMRG is currently a group in transition. Mining boom and downturn cycles have exacerbated the loss of accumulated knowledge in the core CQMRG membership due to rapid changes in personnel at mines in the region. Additionally, some of the most experienced CQMRG-affiliated rehabilitation practitioners are approaching the end of their careers and want their valuable and less formal knowledge retained. This paper discusses the development of a research project that emerged in response to the anticipated loss of several decades’ worth of valuable knowledge as rehabilitation practitioners in CQMRG left the region or the workforce.CITATION:Unger, C J, Bond, C J, Baumgartl, T, Glenn, V C and Sabourenkov, P, 2016. ‘MRC-wiki’ – a mine rehabilitation and closure knowledge management tool for Central Queensland coalmine practitioners, in Proceedings Life-of-Mine 2016 Conference , pp 39–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By M Costa, L Polizzi

Process optimisation and continuous improvement are usually acknowledged when making a process more effective, efficient and transparent. During the last few decades, thousands of companies around the world have used total quality concepts in order to establish a continuous improvement process in their companies. Typically these companies apply some kind of Kaizen-type tools and expect results in the short term; however, the great majority of companies are poorly implementing these continuous improvement programs.Usually the most common reasons for failure of the program are lack of commitment from leaders, lack of discipline and engagement from the team to follow process and lack of clear targets for the program. When the results do not come at the expected timeline, it is common to simply drop the current process and apply a different approach from another company or consulting firm.This paper will explore some successful cases of companies that have invested time and effort to establish a reliable and sustainable process of continuous improvement. The focus will be case studies of mines and smelters around the world that use the plan–do–check–act (PDCA) cycle to increase productivity with the best services and lowest costs. The main tools and processes used by these companies will be discussed, as well as results achieved.CITATION:Costa, M and Polizzi, L, 2014. Introducing and sustaining a continuous improvement program in mines and smelters, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 55–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By E de Necker, F D. I Hodg, L-M Cruywagen

The acid mine drainage (AMD) situation at three opencast collieries in the Witbank Coalfield, South Africa, was evaluated from different perspectives. Twenty-seven test pits were dug into the spoils of these collieries to characterise the in situ conditions of spoils of varying age. Detailed static testing was done on surrounding drill holes and additional samples were taken from the test pits. Selected samples were tested using different techniques, namely ABA, mineralogy and kinetic tests. Groundwater monitoring boreholes from the areas surrounding these spoils were also used for characterisation. The ABA results compared favourably with the in situ determinations; acidic test pits proved to be potentially acid-generating from ABA, even when the samples had neutral paste pH. Kinetic test results showed these samples to yield low pH leachate over the test period. In several of these results, the theoretical depletion of neutralising potential and the onset of acidity were well matched. NAG pH-values and final observed water chemistry corresponded for the cells predicted by ABA to acidify, but compared poorly in cells that did not acidify. Results from the non-acidic spoils were consistent with the in situ observations. Alternative kinetic test methodologies were also employed. Duplicate samples were tested in humidity cells and in aerated trays that were manually wetted on a regular basis. Results from these tests showed an excellent correlation. Detailed mineralogical determinations using XRD and XRF were used for comparison to the ABA and, in some cases, humidity cell results. These comparisons show that the ABA results are consistent with the results expected from the mineralogy. The conclusion from these assessments is that ABA, in most cases, provides information that can be correlated to the field, mineralogy and to humidity cells. The use of multiple techniques leads to a higher degree of confidence in the use of the data.

Jan 1, 2003

By M I. Pownceby, M A. Rhamdhani, D M. Fellicia, S Palanisamy, R Z. Mukhlis

The trend of global copper production has prospectively increased over time. Based on typical mined ore grades, 1 t of copper ore generates approximately 6–10 kg of copper, which requires much energy, usually in the form of metallurgical coke. Copper production using carbon as a fuel and reductant contributes up to 0.3 per cent to global greenhouse gas (GHG) emissions. As a result, research into decarbonisation processes applicable to reducing low-grade copper sulfide ores, copper oxides, electronic wastes and other alternative complex Cu-rich materials has increased. Alternative fuels for reducing carbon-rich emissions in pyrometallurgical copper processing include methane, ammonia, biomass, solar and wind power, but in recent times increased focus has been on hydrogen as a potential fuel and reducing agent for materials such as oxidised copper scrap, Cu2O/CuO and Cu-rich slags/e-wastes. From a thermodynamic perspective, hydrogen exhibits a significantly more negative standard Gibbs free energy (ΔG°) than copper oxide making it a suitable reductant and the exothermic thermal effect from reaction between hydrogen and Cu2O/CuO may be used to control process parameters. These characteristics renders hydrogen an ideal gas for reducing copper oxides and copper-containing slags/e-wastes. This review article assesses previous research on utilising hydrogen for producing and refining copper from primary and secondary feed materials.

Jun 19, 2024