Search Documents

By L. Stone, H. Margolin

The Ti-C-N and Ti-C-O systems were investigated in the temperature range from 500° to 1400°C and in the composition range up to 2 pct C and 5 pct N or 0. Characteristic isothermal sections at 800°, 900°, 1000°, and 1300°C are presented. The Ti-N-0 system was studied in the temperature range from 900' to 1400°C with alloys containing up to 6 pct total alloying content. Characteristic isothermal sections at 1000° and 140O°C are presented. Melting-point data for all three systems are also included. THIS paper reports on one of a series of investi-gations which have been conducted on the phase diagrams resulting from interstitial alloying with iodide titanium. The other investigations involved delineation of the binary systems with carbon,' nitrogen and boron,h and oxygen. The Ti-0 binary system has also been investigated by Bumps et al.' In varying degrees, each of these interstitial elements has been shown to stabilize the low temperature a modification of titanium1-5 and each forms a face-centered cubic TiX compound (henceforth designated 6). In addition, the Ti-N and Ti-0 systems reveal a low temperature tetragonal phase (6) formed by a peritectoid reaction between a and TiX Experimental Procedure The development of experimental techniques for the study of titanium alloy systems has, to a large extent, become standardized. In this investigation, the equipment and procedures described in detail by Cadoff and Nielsenl have been used. Arc Melting: In general, binary alloys with carbon, nitrogen, and oxygen, prepared in the composition range of interest in this investigation, show negligible composition changes during arc melting. However, the possibility of the formation of some gaseous combination of alloying elements such as CO, CN, or NO during the preparation of these ternary alloys was considered. Calculations showed that the evolution of only 0.05 gram of such a gas would be detectable as a pressure change in the closed system used during preparation of these alloys. Such pressure changes were not observed. Consequently, nominal compositions have been used in plotting the data. The compositions of the materials used in the preparation of the alloys are shown in Table I. After melting for 3 to 5 min at 275 to 350 amp, the alloys were checked for homogeneity by microstruc-tural examination. Alloys containing up to 1 pct C were homogeneous in the presence of less than 3 pct N or 0. At higher alloying contents, some inhomo-geneities in the carbon distribution became evident. Alteration of the melting procedure toward longer times and higher currents did not improve the homogeneity of these alloys. Ti-N-0 alloys were homogeneous in the range to about 3 or 4 pct total alloying addition. Beyond this, almost all of the specimens showed as-cast microstructures consisting only of the phase. Consequently, inhomogene-ities could not be detected by examination of micro-structures. Ten alloys from each of the systems were analyzed for two of the elements present (oxygen being omitted in all cases and titanium being omitted in the Ti-C-N alloys). In all cases the analyses were found not to be sufficiently precise to serve as criteria for the total composition of these alloys. On the basis of phase distribution in heat-treated alloys, however, it appears that carbon is distributed throughout the alloys most uniformly, with oxygen and nitrogen following in that order. Heat Treatment: Specimens for heat treatment were wrapped in titanium sheet before sealing in the argon-filled quartz capsules. Heat-treatment times varied from 100 hr at 800°C to 0.5 hr at 1400 °C. After heat treatment the specimens were quenched by breaking the capsule in water. With the exception of alloys in the low composition region, heat treatment did not have an appreciable effect on the as-cast microstructures. Metallography: Following heat treatment, the specimens were prepared for metallographic examination by grinding on emery paper and electrolytic polishing. For the majority of the specimens a 10-sec etch with Remington "A" agent (25 pct HNO3, 25 pct Hf, and 50 pct glycerin) adequately

Jan 1, 1954

By J. F. Smith, J. E. Davison

A value for the enthalpy of formation of z2 of -3.14 i 0.21 kcal per g-atom has been measured by the technique of acid solution calorimetry. This result is in quite good agreement with two earlier determinations by tin solution calorimetry and by direct reaction caloriinetry, and averaging of values determined from the three independent calorimetric techniques gives enhanced precision and accuracy with AHh8 (CaMgZ) = - 3.15 i 0.05 kcal per g-atom. For comparison with experimental data, values for the enthalpies of formation of CaMgz, SrMgz, and BaMgz of -9.8, -7.9, and -2.8 kcal per g-atom were estimated from a calculation based on the LVigizer-Seitz approximation as modified by Raimes for polyvalent elements. While complete quantitative accord between these calculated talues and available experimental data is lacking, nonetheless numerical accord is better than might be expected and, more importantly, parallel numerical trends are observed between experimental and calculated vnlues. WITHIN the past decade the enthalpy of formation of CaMg, has been determined a) from measurement of magnesium vapor pressures over binary Ca-Mg alloys,' b) by solution calorimetry with liquid tin as the solvent,' c) from measurement of hydrogen vapor pressures over ternary alloys of calcium, magnesium, and hydrogen,3 and d) by direct reaction alorimetr. The value from tin solution calorimetry is the most precise and is probably the most reliable, and this value is within the quoted uncertainties of the other three experimental results. The overall agreement among the four independent investigations is quite good, particularly so when the diversity of techniques is noted. On the basis of this agreement, CaMgz was chosen as a test material to evaluate the operation of a newly constructed apparatus for the determination of enthalpies of formation of intermetallic phases by acid solution calorimetry. This was believed to be a severe test because of the high chemical reactivity of both calcium and magnesium which reactivity presumably accounts for the fact that an early determination5 of the enthalpies of formation of Ca-Mg alloys by acid solution calorimetry yielded values significantly more negative than the four recent determinations. EXPERIMENTAL APPARATUS AND MATERIALS Experimental Apparatus. The enthalpy of formation of CaMg, was determined by measuring the difference between the heat evolved when dissolving the metallic compound and the heat evolved when dissolving equivalent amounts of unreacted metallic elements in hydro- chloric acid. This was done differentially with an apparatus consisting of twin calorimeters which were constructed to be as nearly identical as possible. The advantage of differential calorimetry is that systematic errors arising from the individual calorimeter design tend to cancel. A schematic representation of the apparatus is shown in Fig. 1. A dead air space around both calorimeters was provided by a large, thermally insulated jacket. Each calorimeter consisted of a 2-liter Dewar flask which was completely enclosed in a copper container. Each Dewar contained 1600 g of 2.5hr HCl to act as the solvent, and thermal effects resulting from solvent evaporation were minimized by covering the acid with 50 g of mineral oil. There was no detectable reaction between the acid and the mineral oil. Equivalent amounts of mechanical energy were added to the calorimeters through twin stirring rods which were driven at the same rpm by a single motor with the intent of the stirring being to maintain thermal equilibrium throughout the solvent. To calibrate the heat capacities of the calorimeters, known amounts of electrical energy could be added by passing measured voltages and currents for known times through submerged heaters, approximately 20 ohms, which were wound noninductively from Manganin wire. A 6-v storage battery was used as a power source, and a dummy heater was used as an exercise circuit to allow the battery to stabilize at a constant electromotive force before energizing one or the other of the calorimetric heaters. A type K-2 potentiometer was used to measure the potential drop across an energized heater while the current was determined from the potential drop across an external standard resistor. Times of energization were measured with an electric timer, and the electrical energy supplied to a heater

Jan 1, 1969

By M. E. Fine, A. A. Henderson

Investigation of the tensile properties of silver based aluminum alloy crystals was undertaken because it appeared attractive for studying strengthening effects due to Suzuki locking with minimum complication. Yield drops were observed in all alloy crystals (1, 2. 3. 4, and 6 at. pct Al) after strain aging at room temperature. No yield drops were found in similarly grown and tested silver crystals. The yield effects are attributed to Suzuki locking but the major portion of the solid solution strengthening to other mechanisms. INVESTIGATION of the tensile properties of single crystds of silver alloyed with aluminum was undertaken because it appeared to be a system in which segregation at stacking faults associated with partial dislocations1 would be the dominant factor in anchoring dislocations. First, silver and aluminum have closely similar atomic sizes and thus solute atom locking of a dislocation due to elastic interactions should be unimportant. Second, while both X-ray2 and thermodynamic3 investigations show short-range ordering in silver-based aluminum alloys, the degree of local order is quite small (X-ray measurements give v = EAB - 1/2(EAA + EBB) = - 0.025 ev and thermodynamic measurements give v r -0.007 ev) and should not be important in strengthening dilute alloys. Third, the stacking fault energy of silver is probably low (as indicated by the profusity of annealing twins) and is very likely diminished further and quite rapidly by aluminum additions since the A1-Ag phase diagram shows a stable hexagonal phase at only 25 at. pct Al. Also, a careful investigation in this laboratory4 has shown that the ratio of twin to normal grain boundaries in recrystallized alloys increases with aluminum content. Thus, with minimum complication from other factors, Ag-A1 alloys seem attractive for studying strengthening effects due to segregation at stacking faults of extended dislocations. EXPERIMENTAL METHOD Single crystals measuring 250 by 5 by 1.5 mm of pure Ag (99.99 pct) and Ag-A1 alloys (A1 of 99.999 pct purity) of nominal compositions* 1, 2, 3, 4, and 6 at. pct were grown in high-purity graphite molds from the melt under a dynamic vacuum (1 x l0-5 mm Hg). The technique consisted of moving a furnace having a hot zone (which melted about 0.5 cm of alloy) over a horizontal, evacuated quartz tube con- taining the mold and alloy at a rate of 3/8 in. per hr. Chemical analysis showed roughly the first inch of the crystal to be solute poor, the last inch solute rich; and the center section uniform in composition within the sensitivity of the analytical method (± 0.2 at. pct Al). The center section of the crystal was cut into five specimens. Gage lengths of reduced cross section, measuring from 1.5 to 2 cm in length, were mechanically introduced by means of jeweler&apos;s files and fine abrasive cloth with the crystal firmly held in polished steel guides. One-third of the cross section was then removed by etching and electro-polishing, the crystals were all subsequently annealed for several days at 850°C in a dynamic vacuum (<1 x 10-5 mm Hg) and furnace cooled to 200°C. The crystal orientations were determined using the usual back-reflection Laue technique. The Laue spots were sharp and of the same size as the incident beam. However, microscopic examination showed the crystals to contain substructures with subgrains of the order of a micron in diameter. The details of this substructure are presently under investigation. Tensile testing was done with a table model Instron using a cross-head speed of 0.002 in. per min. For testing at various temperatures the following media were used: 1) 415oK, hot ethylene glycol; 2) 296ºK, air, acetone, water; 3) 273ºK, ice water; 4) 258ºK, ethylene glycol "ice" in ethylene glycol; 5) 200°K, dry ice in acetone; 6) 77ºK, liquid nitrogen. EXPERIMENTAL RESULTS A) Yield Behavior—A portion of an interrupted stress-strain curve for a 6 at. pct A1 crystal of the indicated orientation tested at room temperature is shown in Fig. 1. Initially, at (a), there is a small, gradual yield drop of about 10 mg per sq mm2. However, on stopping the test, and aging for a few minutes at (b), a sharp yield drop is found. Aging for longer times at (c) and (dl results in larger yield drops (and larger AT&apos;S). At, defined in Fig. 1, is usually larger than the yield drop by about 20 pct; however, this increase in the lower yield is transient since extrapolations of the flow stress curves join as may be seen from Fig. 1. (Both Laue and low-angle scattering photographs revealed no evidence of precipitation in a strain-aged 6 at. pct A1 crystal.)

Jan 1, 1962

Established as a Division December 15, 1948 Evan Just, Chairman Richard J Lund, Past Chairman Granville S. Borden, Vice-Chairman J K Richardson, Vice-Chairman S H Williston, Vice-Chairman Allan Matthews, Secretary-Treasurer National Security Resources Board 17th and Pennsylvania Ave, N W Washington 25, D C

Jan 1, 1952

Admissions: Joseph C. Gordon, Chairman K. F. Anderson Allen B. Gibson H. J. Gruy R. F. Madera Dan H.-McLendon K. W. Robbins Aurel E. Smith W. F. West Advertising: John. D. Wisenbaker, Chairman Bernard F. Klein Henry N. Lyle R. E. Howard Clark R. Edgecomb, Jr. [ ]

Jan 1, 1961

By W. A. Bruce

This paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown Whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to well-spacing problems are shown. Introduction The pressure-prediction methods to be described here are based upon the conception of an oil pool as a small part of a large porous continuum, containing for the most part water. The formation containing this water may be thought of as extending over an area of many square miles and having one or more small bodies of oil or gas trapped in high spots or reservoirs. It will be treated as having the genera1 aspect of a thin, flat sheet with an over-all tilt to the horizontal and with numerous small high spots, tight zones, and irregularities This porous continuum will be treated as being much more extensive than the oil or gas zones, but will be recognized as terminating at such large boundaries as a general fault, outcrop, unconformity, or pinch-out. Throughout the greater part of this limited porous continuum it is likely that there is a hydraulic connection. If this is true, the removal of fluid in one place will cause a disturbance that eventually will travel to all parts of the continuum. This picture has led to the recognition of water as the major fluid in the porous continuum and in many cases the expansive nature of this water as the main driving force producing the oil. The next step is the solution of the general problem of compressible liquid behavior in porous media. The works of Hurst I and Muskat2 introduced the idea of using heat-flow mathematics to consider the problem of compressible liquid flow in a porous medium. Before their reports, it had been thought sufficient to use the incompressible fluid-flow work of S1ichter.3 Law Muskat4 pointed out in detail how far the incompressible-fluirl assumption, deviated from fact even for water, of which the compressibility is about 3 X 10-6 volumes per unit volume per pound per square inch. He showed that this deviation increased with increases of distance. For example, the incompressible-fluid formula might show good agreement with the

Jan 1, 1943

By W. A. Bruce

This paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown Whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to well-spacing problems are shown. Introduction The pressure-prediction methods to be described here are based upon the conception of an oil pool as a small part of a large porous continuum, containing for the most part water. The formation containing this water may be thought of as extending over an area of many square miles and having one or more small bodies of oil or gas trapped in high spots or reservoirs. It will be treated as having the genera1 aspect of a thin, flat sheet with an over-all tilt to the horizontal and with numerous small high spots, tight zones, and irregularities This porous continuum will be treated as being much more extensive than the oil or gas zones, but will be recognized as terminating at such large boundaries as a general fault, outcrop, unconformity, or pinch-out. Throughout the greater part of this limited porous continuum it is likely that there is a hydraulic connection. If this is true, the removal of fluid in one place will cause a disturbance that eventually will travel to all parts of the continuum. This picture has led to the recognition of water as the major fluid in the porous continuum and in many cases the expansive nature of this water as the main driving force producing the oil. The next step is the solution of the general problem of compressible liquid behavior in porous media. The works of Hurst I and Muskat2 introduced the idea of using heat-flow mathematics to consider the problem of compressible liquid flow in a porous medium. Before their reports, it had been thought sufficient to use the incompressible fluid-flow work of S1ichter.3 Law Muskat4 pointed out in detail how far the incompressible-fluirl assumption, deviated from fact even for water, of which the compressibility is about 3 X 10-6 volumes per unit volume per pound per square inch. He showed that this deviation increased with increases of distance. For example, the incompressible-fluid formula might show good agreement with the

Jan 1, 1943

By K. A. Pauly

Compressed air has been and is still very extensively used in connection with mining-operations, but its application in the past has been almost entirely confined to supplying power to underground machinery. Its introduction was due to the difficulty of taking care of the steam which is exhausted underground, rather than to any advantage in efficiency to be gained by its use. The ease with which electric power may be carried to the remotest parts of the mine and the high efficiency of the electric motor have long been appreciated by mine-operators, and electric power is now extensively used underground in the more recent developments, while many of the compressed-air engines in the older workings are being rapidly replaced by electric motors. Recently, however, it has been suggested to use compressed air for driving the large shaft-hoists, the air for the engines being supplied by electrically-driven compressors, and an installation of this character is being erected at Butte, Mont. It is the object of this paper to compare the compressed-air system of hoisting with the various electrical systems, from the stand-points of first-cost and cost of operation. However, before entering into a discussion of the various systems, it will be well to consider briefly the conditions affecting the choice of a system of hoisting in which electricity is the ultimate source of power. The power required by a mine-hoist is extremely intermittent and fluctuates between very wide limits, the all-day average consumption of power not exceeding from 5 to 15 per cent. of the maximum demand during hoisting. The cost of supplying power for such a fluctuating load is necessarily higher than that for supplying an equal amount of

Jan 1, 1912

By John W. Wagner, Robert K. Willardson

Single crystals of Pbl-xSnxTe have been grown from nonstoichiometric, cation-rich melts with the objective of producing as-grown, bulk material containing carrier concentrations ranging from 1016 per cu cm to 1018 per cu cm. Three specific crystal composi-tions were investigated in detail; x = 0.00, 0.10, and 0.17. Pull rates of from I to 3 mm per hr were used. Single crystals were successfully pulled from melts containing as little as 30 at. pct Te. Hall coefficients, resistivities, and carrier mobilities of these materials were determined. The relationship between the composition of the melt and the carrier concentration in the as-grown crystal has been studied for the three crystal compositions of interest. BULK single crystals of Pb,-,Sn,Te have previously been grown from stoichiometric melts.1,2 Such crystals are p-type and have relatively high carrier concentrations ranging from -9 x 1018 per cu cm for PbTe to -8 x l020 per cu cm for SnTe at 77°K. These carrier concentrations result from deviations from stoichiometry (lead vacancies) in the as-grown crystals. Since lower carrier concentrations are desirable for electrooptic device applications, these crystals are usually subjected to long-term, isothermal anneals.&apos; This paper reports on the growth of Pbl-xSnxTe single crystals from nonstoichiometric melts with the primary objective of producing as-grown material containing relatively low (1016 to 1018 per cu cm) carrier concentrations and also reports on the general characteristics of these crystals. The phase relationships in the Pbl-xSnxTe systems are such that materials solidifying from nonstoichiometric, cation-rich melts will have smaller deviations from stoichiometry than materials grown from stoichiometric melts. Fig. 1 is the T-x phase diagram for PbTe in the vicinity of the stoichiometric composition.3 A crystal grown from a stoichiometric melt will solidify at a melting point maximum at which the solid will contain -0.5002 atom fraction of tellurium. PbTe single crystals grown in our laboratories from stoichiometric melts have carrier concentrations of 9 x 10" per cu cm, indicating that the excess tellurium in the crystals is as expected from this phase diagram. However, growth of PbTe from a lead-rich melt will result in material having a more nearly stoichiometric composition. Although the addition of Sn to the melt shifts the solidus curve further toward the tellurium-rich side,4 the general discussion given for PbTe applies to the Pbl-xSnxTe systems as well. EXPERIMENTAL Single crystals of Pb1-xSnxTe have been grown in our laboratories from nonstoichiometric, cation-rich melts using the Czochralski technique and boric oxide liquid encapsulation. The details of the growth apparatus and growth technique have been reported in a previous paper on growth of these alloys from stoichiometric melts.2 In the present study, three specific crystal compositions were investigated in detail; x = 0.00, 0.10, and 0.17. Growth of alloy crystals from nonstoichiometric melts requires considerable care, and good quality single crystals were obtained in this study only by optimizing the mechanical and thermal stability of the growth system and by using pull rates of from 1 to 3 mm per hr (Pbl-xSnxTe crystals are easily pulled from stoichiometric melts at rates of from 5 to 10 mm per hr). The liquid encapsulation technique was found to yield near-ideal conditions, since the B2O3 layer increased the thermal stability at the growth interface, permitted easy attainment of near-ideal thermal gradients, and dampened vibrations at the melt surface. The hygroscopic character of the B2O3 was a slight problem and vacuum heat treating was necessary to completely remove the water from the boric oxide. During initial growth, the seed diameter was reduced and a narrow neck (1 to 2 mm diam) of several millimeters length was grown. The latter steps were found to be necessary for the growth of single crystals, i.e., if either of these two requirements were

Jan 1, 1970

By B. J. Reid, J. N. Greenwood

It has been shown1 that cavities are formed in the grain-boundaries of copper and 70:30 brass (as well as in magnesium) by the application of tensile stresses at elevated temperatures. For a given rate of strain, cavities are formed in brass at a lower temperature than in copper, and they are larger; it was thought that this earlier onset of cavitation in the alloy might be caused by the distortion produced in the metal lattice by the alloying element. If the cavitation is caused by the vacancy-migration mechanism, &apos; the distortion of the lattice would reduce the energy required for vacancy formation, and thus provide vacancies more readily to assist in the cavitation process. It was decided to study a range of alloys to find out whether increasing amounts of an alloying element would cause any progressive increase in, or modification of, the cavitation in copper. Nickel was chosen for this purpose, since it is soluble in copper throughout the whole range of alloys. A further advantage was its low vapor pressure, which enabled the preparation of the alloys in vacuum and the consequent reduction of their hydrogen content. It has been suggested that cavities may be nucleated by the migration of hydrogen atoms to the less regular atomic spacing at the boundary, and their combination to form molecules. The latter being too large to diffuse back into the lattice, form stable cavities into which vacancies could condense. PREPARATION OF ALLOYS All alloys, ranging from pure OFHC copper to 43.7 at. pct of nickel (carbonyl), were prepared in a vacuum furnace employing high-frequency induction heating. When a charge was melted, vigorous gas evolution occurred initially, after which the pressure was reduced to 10-4 mm Hg, using an oil-diffusion pump. After remaining molten for a further 1/2 to 1 hr to aid degassing, the melt was allowed to solidify in the crucible. In this way contamination by gases evolved from the surface of a separate mold was avoided. The list of alloys prepared is shown in Table I. The percentage of hydrogen present in the OFHC copper was reduced from 0.0054 at. pct to 0.0012 at. pct, as measured by a vacuum-fusion method. The alloys were cold-rolled to 0.03-in.-thick strip, and were homogenized in vacuum for 1 hr at 900°C after every 30 pct reduction. At a thickness of 0.05 in., the strip was held at 450°C for 24 hr under high vacuum (10-5 mm Hg) in an attempt to reduce the hydrogen content still further. Tensile specimens were prepared with a gage length of 1 in., and were finally annealed for 2 hr at 800°C to give an average grain diameter of 0.1 mm. TENSILE DEFORMATION The specimens were deformed in a tensile straining machine operated by a synchronous motor at a constant rate, equivalent to 1.7 pct per hr on a 1-in. gage length. The specimen and grips were contained in a vacuum jacket. A pressure of 10-2 mm Hg was maintained, which was sufficient to prevent surface tarnishing of a specimen held at 650°C for 24 hr. Tests were made between 20. and 650°C and the temperature was controlled to within ±3° over the gage length. The load was measured by the deflection of a cantilever spring. a) Mechanical Properties-The ductility curves shown in Fig. 1 fall into two groups. Figs. 1(a) and (b) for copper and the 5 pct nickel alloy, respectively, show a continuous fall in ductility with a steep fall between 200° and 400°C. Figs. l(c) to (f) show the same sudden loss of ductility between 200° and 400°C. With higher temperatures, however, there is a recovery in ductility values to a maxi-

Jan 1, 1959

By H. B. Kinnear

THE first copper stool used under an ingot mold to receive molten steel has recently been taken out of service after it had received ingots amounting to 6012 gross tons. This stool, weighing 8330 lb. had been in continuous service for 1822 heats since its installation. From this modest beginning the use of copper for ingot-mold stools grew to 425,000 lb. in 1934, with an additional 50,000 lb. of copper used in the form of inserts in cast-iron stools. During 1935 the quantity of copper used for stools increased by about 350,000 lb., making a total of 775,000 lb. now in use for that purpose. Copper used for inserts has increased during this time 180,000 lb., or over 350 per cent, to a total of 230,000 lb. The total of copper, therefore, in use at present under ingot molds is slightly over 1.000,000 lb.

Jan 1, 1936

By R. J. Blackwell, J. R. Rayne, W. M. Terry

This paper presents results of an experimental investigation of factors that control the efficiency with which oil is displaced from porous media by a miscible fluid. The study was made to elucidate the relevant processes both on microscopic level (within individual or between neighboring pore spaces) and on macroscopic level (within a large sand body). Mixing of miscible fluids on the microscopic level was studied in sand-packed tubes. It was found that molecular diffusion is the dominant dispersion mechanism for reservoir conditions of rate, length and pore sizes. Macroscopic channeling was studied for various mobility ratios in reservoir mode1s scaled to relate viscous, gravitational, and diffusional forces. The formation of channels was due to viscous firzgering, gravity segregation and variations in permeability. With adverse mobility ratios, it was found for reservoirs of realistic widths that diffusion will not be effective in preventing the formation and growth of fingers, even in homogeneous sands. At sufficiently low rates channeling was eliminated by gravity segregation in tilted reservoirs. The dependence of recovery on mobility ratio, length-to-width ratio, flow rate and angle of dip is presented. INTRODUCTION Oil recovery by solvent flooding is finding increasing application in the field. While the process promises high recoveries from the region swept by solvent, under adverse conditions only a small fraction of the reservoir volume may be swept at the time solvent breaks through to the producing well. Further, the high cost of the solvent encourages its use only as a bank whose size must be kept at a minimum. Thus, two important questions arise: (1) what fraction of the reservoir can be swept, practically, by solvent? and (2) what is the minimum size solvent bank that can be used to carry out the displacement? The answers to these questions require knowledge of both macroscopic channeling processes and microscopic mixing processes. The studies described here were carried out to gain this knowledge. Microscopic mechanisms which cause mixing will be discussed first, because an understanding of these mechanisms is necessary for proper interpretation of the experimental work on channeling described later. INVESTIGATION OF MICROSCOPIC DISPLACEMENT PHENOMENA FOR MISCIBLE FLUIDS The questions to be resolved concerning microscopic displacement behavior are: (1) how much mixing occurs between oil and solvent in the direction of flow? and (2) does the solvent completely flush the oil from the pore spaces in the region invaded by solvent? The classic work of Sir Geoffrey Taylor&apos; and its extension by Aris2 have shown that it is possible from theory to describe the amount of mixing in single straight capillaries when solvent displaces a fluid of equal viscosity and equal density. Aris showed that the lengths of the mixing zones, 81, corresponding to the 10 per cent and 90 per cent concentration levels of the solvent can be calculated from the formula, 81 = 3.62 \/Kt, .........(1) where 8l is the length of the mixing zone, cm; t is the time, sec; and K is the effective dispersion coefficient, cm2/sec, given by K/D = 1 + (1/48) (au/D)2......(2) where a is the radius of the capillary, cm; D is the molecular diffusivity, cm2/sec; u is the average velocity

A. Bement, Chicago,Ill. (communication to the Secretary*):— Formerly it was the general practice of engineers to designate coal that is free from moisture and ash as " combustible," notwithstandirig that it contains oxygen and nitrogen. The origin of this practice was more particularly due to the requirements in connection with boiler-testing, which demanded a consideration of that portion of the fuel which took part in the combuition-process because results based on a unit of either moist or dry coal were not comparable, since both moisture and ash were recognized as variable quantities. Thus, a pound of " combustible " became a standard of value, and was treated as a constant before employing measurements of heating-power and calculating therefrom the percentage of efficiency. The recognition of this term " combustible " was an advance to be credited to the engineer rather than to the chemist, because the latter, not having to do with the interpretation of analyses in practice outside the laboratory, usually saw no reason for reporting results in terms other than those of the moist-coal composition. Some years ago I needed a table of fuel-composition in terms of moist, dry, moisture-free and ash-free coal, and of the combustible components. This table required the use of the word combustible in its proper sense, for the purpose of designating carbon, hydrogen, and sulphur, instead of including these three elements with oxygen and nitrogen, to which aggregate the term combustible was formerly applied. To make such a tabulation involved either the use of the inconvenient and cumbersome term, "ash- and moisture-free coal," or of some other representative term, and for this purpose I adopted the expression pure coal, which is short, simple, convenient, and technically correct. It is also harmonious, because it agrees

Jan 1, 1909

By G. R. Love, M. L. Picklesimer

Aboue 950°C the Nb-Zr system consists of a completely miscible bcc solid solution, commonly called the phase. Between 950 and 600°C, and between 20 and 85 pct Nb, the phase deconlposes, after sunciently long times, into two bcc solid solutions. The pct Zr alloys are conveniently descibecl with T-T-T (time-temperature-transformation) curves having a nose at about 2 hr at 700°C. The reaction rate varies only slowly with zirconium content and negligibly with oxygen contanzination; it is speeded up by a factor of 10 to 15 by 90 pct cold ulork and slowed dou by n factor oj 10 to 30 by a two-hundrecljold increase in grain size. Nb-r alloys with compositions between 40 and 85 pct Nb have been the basis for the majority of commercially important superconducting materials. In part because of their commercial promise, more is known about these alloys than about most other high-field superconducting materials. At the same time, there is considerable disputed or incomplete metallurgical information. For example, although Rogers and tkins&apos; indicate a monotectoid reaction at approximately 600°C and a two-phase 01 + 0, field extending between 20 and 85 pct Nb and to a maximum of 95OGC, erhout&apos; has reported that this entire region would be a single homogeneous B were it not for oxygen contamination. Again, although it has been shown that relatively short-time heat treatments in the vicinity of 700CZ significantly improve the ability of short wire samples to carry high currents in high magnetic fields at 4.2K, these observations have never been fully correlated with the structural change or changes occurring during the anneal. We intend to investigate in detail the effect of metallurgical variables, including heat treatment, on the superconducting properties of hard superconductors. To verify that our experimental techniques are valid and to establish a relative standard against which other materials may be measured, we feel it advisable to know the behavior of the Nb-Zr alloys under a variety of processing conditions. As an initial step toward this goal, we have determined in detail the kinetics of the transformations in Nb-Zr alloys. EXPERIMENT A number of problems had to be solved before beginning any fruitful work on the reaction kinetics in this system. While solving some of these problems, either by chance or by design, small amounts of information were obtained about alloys containing 40, 50, 60, 65, 67, 70, and 75 pct Nb, bal. Zr. In addition, a large range of grain sizes and a range of temperatures considerably greater than the range indicated by Rogers and Atkins phase diagram were examined. We will, however, report in detail only the results obtained for the Nb + 33 pct Zr and Nb + 25 pct Zr alloys at three grain sizes, two levels of oxygen contamination, and the temperature range 550 to 950°C. These data are most complete, but the other data are sufficiently complete to indicate the kind and magnitude of the variation of the transformation kinetics outside this range. The first and most difficult problem encountered in this inquiry was one of sample homogeneity. When Nb-Zr alloys are arc- or electron-beam-melted on a cooled copper hearth, solidification is sufficiently slow that there is appreciable coring in the cast structure and a large variation of grain size across the button thickness. Both these factors significantly affect the apparent reaction rate in the system. A two-step solution to the problem was attempted; an arc-melting and drop-casting technique has been developed by conald that greatly reduces the as-cast grain size and virtually eliminates coring segregation. Ingots made in this way exhibited no detectable (3 pct maximum) zirconium segregation. Before it was evident just how good this technique was, we attempted to supplement it with rather long-time, high-temperature annealing of the cast ingots. This annealing was carried out in evacuated and sealed (seal-off pressures < 1.0 x 106 torr) quartz capsules lined with tantalum foil at 1400 to 1450 C for 8 to 72 hr. There were two principal effects of this treatment: the grain size increased to a fairly uniform 150 p, and the surface and all grain boundaries near the surface acquired a film of a second phase, tentatively identified as an oxide (possibly additionally contaminated with silicon). There was no evidence that this 1400 C treatment had affected the zirconium segregation. High-temperature annealing was subsequently used only for grain-size control, but anneals of longer than 4 hr at temperatures greater than 1000°C were performed in dynamic vacuums (pressure no greater than 1.0 x lo torr). Any contamination resulting from these treatments was well below the limits of detection of our techniques. All samples, as cast, were cold-swaged to at least 85 pct reduction in area. The samples called cold-worked were tested as swaged. The minimum re-crystallization anneal for these alloys was about 12 hr at 1050 C; this produced an equiaxed grain diameter of about 4 to 8 P. Annealing for 4 hr at 1450°C produced a grain size of about 80 to 150 p; and annealing for 4 hr at 1650aC, close to the melting point of many of these alloys, produced a grain size of 0.5 to 1.0 mm. At all temperatures, the larger grain size was

Jan 1, 1967

By R. G. Woolery

INTRODUCTION Since 1975, Union Carbide Corporation has been conducting uranium exploration in southwestern South Dakota. This program has resulted in the discovery of an ore body about eight miles north of Edgemont in Fall River County. The site which was previously mined for uranium in the 1950&apos;s and 1960&apos;s consists of 950 lode claims (approximately 20,000 acres) and is within the Black Hills National Forest. Preliminary development plans indicate that fewer than 200 surface acres will be involved in the mining and heap leaching of the ore. The ore occurs in both the Fall River and Lakota formations. The exploration to date has developed something in excess of two million tons of ore averaging -0.1% U308. About 75% of the ore is expected to be mined from underground with 25% coming from five to seven small pits. The surface mining will be extensions of previously mined areas with a disturbance of 35-40 new acres near 35-40 previously disturbed acres requiring a total reclamation of 70-80 acres. Several options for processing the ore including conventional milling by UCC, conventional milling in joint venture with another producer, and heap leaching are under consideration. This paper is concerned with the preliminary assessment of the heap leaching option based on the limited test work conducted on surface samples and on available cores from the deeper ones. The final design for a commercial operation will not be available until an underground bulk sample has been obtained and evaluated. Union Carbide has been operating heap leach facilities commercially since 1973 at Gas Hills, Wyoming and Maybell, Colorado. During this period, we have made considerable progress in heap construction

Jan 1, 1983

By E. P. Klier

The work of Klier and Lyman1 on the bainite reaction has led to the full description of this reaction for medium-carbon low-alloy steels. Certain experimental data reported by Klier and Lyman appear, however, to be improbable of obtaining in very high-carbon steels. The study herein reported consists of an analysis of the transformation characteristics of a 3 per cent chromium, I per cent carbon steel by means of X-ray and metallographic methods. From the results obtained it is concluded that the bainite reaction in this steel is more complicated than that reported by Klier and Lyman for the low-carbon low-alloy steels. Henever, the mechanism of bainite formation in this steel appears to be essentially the same as proposed for the low-carbon low-alloy steels with the modification that the first volumes to transform are carbon-rich rather than carbon-poor. Experimental Procedure The analysis of the steel studied was: Cr, 2.89; C, 1.02; Mn, 0.33; Si, o.35; S, 0.012; P, 0.020. The stock was received from the Carpenter Steel Co. in rolled bars. Specimen Preparation Specimens were austenitized at 1200°C. (2192°F.) for 25 min. in purified nitrogen. The resultant A.S.T.M. austenite grain size was 0-1. Isothermal transformation was allowed by quenching the specimens into liquid metal baths controlled to 5°C. at 540°C. (1004°F.) and above, and to 2°C. at 490°C. (914°f.) and below. Following the desired degree of transformation all specimens were water quenched. Metallographic Examination Specimens 1/4 in. round by 1/4 in. were used for nietallographic examination. Etch-ants used were Vilella&apos;s reagent (I gram picric acid, 10 ml. hydrochloric acid to make 100 ml. ethyl alcohol solution) and alkalinc sodium picratc (electrolytic). Vilella&apos;s reagent was effective in revealing all microconstitucnts, while the alkaline sodium picrate developed the carbon-rich structures or carbides only. X-ray Examination Two X-ray techniques were used—the Debye-Scherrer method and a back-reflection method. &apos;The small specimens necessary for the Debye-Scherrer method were austenitized and then allowed to transform, or were cut from the larger metallographic specimens. The metallographic specimens were used for the back-reflection X-ray analysis. When it was desirable to determine the structure of the carbide present, sliver specimens were electrolytically etched to develop a carbide coating, then were exposed in the cameras. This technique was frequently necessary to allow positive identification of the carbide.

Jan 1, 1945

By H. F. Silliman, Daniel R. Hull, John R. Freeman

IN the normal operation of a brass-rolling mill, sheet and strip has, for the most part, been finished in comparatively thin gauges, involving a substantial amount of coldwork and a considerable number of anneals. This condition has been disturbed by the prep0nderance of cartridge brass, which is not rolled to thin gauges, and particularly by brass for artillery cartridge cases, on which the mill may finish its work at a thickness between 0.400 and 0.900 in. Obviously, the amount of rolling and the number of anneals to which such a product can be subjected are small compared with strip that is carried to a thickness of a few hundredths of an inch. As a result, critical examination into the internal condition of metal has been made on an extensive scale at a stage of manufacture that would not, in normal times, have been chosen for complete inspection. Under these conditions, a type of defect has been recognized that is not seen at thinner gauges. It might be more accurate to call it the appearance of a defect, since it refers to an apparently laminated, discontinuous structure, which, in fact, does not exist as such, and disappears after suitable treatment. For this reason it has been called a phantom lamination, which the authors consider an appropriate term. It is the purpose of this paper to describe the phenomenon and the conditions of its occurrence and, at least tentatively, to discuss its nature and cause. Great numbers of phantoms may be found in 2: 1 brass, either hot-rolled or cold-rolled. They are also found in 70-30 brass, sometimes when hot-rolled and generally when cold-rolled. It is not believed that phantoms are confined to these alloys but this paper is limited to them for the purpose of description. HOT-ROLLED 2:I BRASS For illustration, therefore, a typical cake of hot-rolled 2: 1 brass has been chosen. This was rolled to a slab 7/8 in. thick, from a casting 5 in. thick by 24 in. wide by 18 in. high, which was believed to have been sound. After hot-rolling and cooling, the slab was sheared and a portion of such a shear cut is shown in Fig. 1. It would be difficult to convince anyone viewing this specimen that the metal was not unsound. The impression would be confirmed by the appearance of a tensile break, as shown in Fig. 2. This is an ordinary tensile-test piece from metal just described. Although there was nothing in its tensile strength or elongation that suggested unsoundness, it appeared run through with pipes and laminations. To question the reality of such a condition would imply questioning the obvious. But, considering the history of the metal, it w0uld be difficult to believe that it could be so bad as it appeared. It seemed reasonable, though, that if the defects were what they appeared to be, they could be traced back from the sheared or broken face.

Jan 1, 1945

By Max Mason

IN 1923 a Western mining company was experimenting with the device of an inventor designed to locate buried ores by radio. Because the progress was slow and the results were confusing, the company began to doubt the usefulness of the method and invited me to review the whole question of the application of physics to ore detection. I was fortunate in securing the cooperation of several physicists who had worked with me during the war on the problem of submarine detection. This group has been increased and has been studying the problem of physical exploration for ores since that time. It was evident that the problem is a big one, with many angles of approach. Its general features may be set down, in rough outline, as follows: The soils, rocks and ores hidden beneath the surface differ one from another in many respects. These differences may be made to furnish a clew for the physicists working from the surface. To bring these differences into action the physicist creates some kind of an effect which penetrates into the ground and is distorted and reflected when it meets boundaries between different sorts of underground structure. In other words, he sends a message down, and the rocks and ore send back signals in reply. In picturing this process, we should not regard the ground as dense and impenetrable. The kind of messages used pass through the earth about as readily as a sound wave travels the air. If, then, the fundamental procedure is to shout down questions in the hope that an orebody will hear and answer back to us, it is clear that a large part of the expert&apos;s study must relate to the kind of questions best suited to the temperament and intelligence of orebodies. It will be easier for the ore to reply to some of our questions than to others, and it is for us to find the right questions. In certain cases, we are spared the necessity of using a messenger; because nature has already provided one. For example, we already have a terrestrial magnetic field which auto-matically and continually conveys messages from underneath. We also have available the earth&apos;s gravitational field. which furnishes us

Jan 1, 1927

By J. E. Burke

RECENT investigations have elucidated many of the phenomena of the grain growth process, but have also revealed some conflicting and unexplained results. Beck and his co-workers1,2,3 have shown that grain growth continues with continued heating at one temperature until the average grain size approaches the thickness of the specimen, Plotting the logarithm of the average grain diameter, D, against the logarithm of the annealing time, t, they find the straight line relationship given by the equation: [D=Ktn [11] with possible small deviations at short annealing times. K and n are constants at constant temperature. On the other hand, Walker4 finds that, in alpha brass, the rate of growth falls off more rapidly than indicated by Eq I after long annealing, so that an equilibrium grain size is approached. Burke5 showed, using Walker&apos;s data, that time and temperature for grain growth are apparently related through an activation energy, H, according to the relationship: [t, Hr i &apos;_ III t„ = R \T, - ~) [2]] where t1 and t2 are the annealing times necessary for the average grain size to increase from Do to D at temperatures T1 and T2 and R is the gas laws constant. In the case quoted, H had the value 60,000 cal per mol. The apparent validity of this relationship, at least up to 700°C, and the approximate value of H were later confirmed by Beck.&apos; The results obtained by Beck, Kremer, Demer and Holzworth2 for aluminum and aluminum-magnesium alloys could not be satisfied by such a relationship, since the slope of the isothermal curves increased with increasing temperature. These data indicate and Beck, Holzworth and Hu6 later demonstrated experimentally that the only apparent factor controlling the rate of grain growth at constant temperature is the grain size. While many of the phenomena have been elucidated, a reasonably quantitative explanation of the process is lacking. There exists uncertainty even as to the primary driving force for grain growth, although there is a considerable body of indirect evidence that the interfacial energy of the grain boundary is responsible.7,8,10 Making implicit use of this assumption, several authors14,15 have pointed out that grain boundaries should migrate toward their center of curvature. Harker and Parker&apos; have advanced this concept furthest, and show that one can expect grain boundary migration to occur only when the grain faces are curved, or when they meet at non-equilibrium angles. When the face is curved toward a grain A, for example, the atoms in the surface of grain B, on the other side of the boundary, are on the average more surrounded by the atoms of their lattice than the atoms on the surface of grain A. Because of thermal motion, the atoms at the interface will sometimes be attached to grain A and

Jan 1, 1948

By E. O. Jones

DURING the heating of cold-worked nickel silver, the tendency of the material to crack is well known. The present research deals with this question, and may conveniently be divided into the following sections: Changes in these alloys during heating and cooling, determination of the temperature at which cracking occurs, effect of grain size, quenching cracks, methods of overcoming annealing cracking. The work is far from complete, in particular the influence of impurities on this tendency has not been investigated, but the results so far obtained lead to certain definite conclusions, which are of theoretical and practical importance. CHANGES IN ALLOYS DURING HEATING AND COOLING During the annealing of many metals at a temperature just below that at which recrystallization sets in, there is evidence of some change, the effect of which is to harden and embrittle the material. This effect has been most clearly demonstrated in the cases of aluminum, copper, brass, and nickel silver, and appears to be a common property of cold-worked metals and alloys, or, at any rate, the non-ferrous ones. The effect would obviously offer an explanation for certain types of annealing cracking, but the trouble is so much more common in the nickel silvers than in the other alloys that some special cause should be looked for. There is, however, fairly good reason for believing that similar cracking may occur in some of the brasses; D. Bunting suggests that the a brasses toward the saturation limit are subject to a transformation closely allied in nature to that known to occur in the nickel silvers at around 320° C. Although the existence of this critical temperature range was known, it did not necessarily follow that this transformation was responsible for the trouble under investigation, so the first portion of this paper deals with the attempts made to determine whether other critical changes might not occur in these alloys. There were already reasons for the belief that such would prove to be the case, as the mechanical properties of the nickel

Jan 7, 1925