Search Documents

By D. A. Munro, G. P. Contractor

Fourteen 50-lb laboratory melts were investigated to determine the effect of uranium on the tenpering characteristics of loo-carbon (0.06 to 0.1 pct C) steels. It was found that uranium additions, particularly in the range 0.30 to 0.45 pct, enhanced the hardness and both ultimate and yield strength of the experivzental steels in the quenched and tempered condition. The structural and morphological chazges indicated that uranium retarded tempering of the tnartensite, thereby hindering the normal formation of polygonal ferrite formed in the late stages of tempering. The effect of this was to make possible the re-tension of the acicilar ferritic structure in the uranium-bearing' steels. The iraniuin-bearing steels also showed IVidnzanstatten-type growth of ferrite plates and had large prior austenite grains containing assenzblies of fine ferrite grains, mainly acicular in geometry. The fine-grained ferrite structure and the presence of more numerous and apparently smaller precipitates in the uranium-bearing steels are thought to he principally responsible for the itnproved tensile strength and hardness of the experinzental uranium-bearing steels. At ternperirzg temperatures above 455% (850'F) the ferrite in the higher-uraniun steels nzaintained acicularity and, hence, its strength and resistance to tempering. Uranium did not produce a secondary hardening peak. However, it retarded softening during the third stage of tempering because of its effect of inhibiting the grouth of cementite particles and of retaining the acicularity of ferrite plates. The resistance to coalescence accounted for the slow grocth of the ferrite grains in the uranium-modified steels and, hence, fov the persistence of the acicular ferrite structure. IT had been found previously1 that uranium additions up to about 0.45 pct had no significant effect on the tensile properties of low-carbon steel (0.06 to 0.10 pct C) in the as-rolled and normalized conditions, Fig. 1. On the other hand, it was observed that uranium in excess of about 0.30 pct had an embrittling effect as revealed by Charpy V-notch impact results. It was also noted that, as the uranium content increased, the morphology of pearlite changed from lamellar to feathery and the ferrite grains showed an etching effect resembling striated or dashed markings, suggestive of precipitation. The sharp drop in the impact properties shown in Fig. 2 warranted an assumption that the uranium content of about 0.30 to 0.45 pct may produce some secondary hardening reaction on tempering, analogous to that associated with a Cr-Mo-V steel, which shows very poor CVN toughness at the secondary hardness peak in the tempering curve.1' With this background and the reported findings of Hasegawa and noda that low-carbon uranium-treated steel showed signs of secondary hardening, the present investigation was undertaken to determine the effect of uranium additions on the mechanical properties of 0.10 pct C steels. No attempts were made to investigate in detail the mechanisms of hardening, although some suggestions based on the experiments are made. MATERIALS AND PROCEDURES A series of 50-lb induction-furnace melts was made using AISI 1008 rimming steel billets as the melting stock. The melting, forging, and rolling techniques proven satisfactory in previous projects'-3 were employed as a guide for this investigation. The steel was deoxidized with aluminum (2 lb per ton) prior to the addition of high-purity uranium. The analysis of each melt is given in Table I. Properties were evaluated as a function of heat treatment and are presented in terms of hardness and tensile strength vs tempering temperatures. The variation of hardness with the tempering temperature was studied on the quenched and tempered specimens, some of which measured 0.50 by 0.25 in. diam and the others 0.40-in. cubes. Before quenching, the specimens were vacuum-sealed in glass tubes and normalized at 900°C (1650°F) for 20 min. Following this treatment, the sealed specimens were hardened by austenitizing at 955°C (1750°F) for 20 min and water quenching, and then tempered for 1 hr in the range 150 to 730°C

Jan 1, 1967

By David E. Hyatt, Christopher H. Cox, Franklin T. Davis

INTRODUCTION The composition of water used in the flotation process has always been of primary interest to the flotation metallurgist. It is by alteration of the chemistry of the water introduced to the process that flotation separation is effected. In only a few cases has it been necessary to treat available water prior to use in the process. In the past, flotation tailings were treated for the removal of solids via the tailings dam and water decanted from the dam was either recirculated to the process or discharged to the surface water system. The choice of recirculation or discharge was based upon water availability, effect of recycle water on the process, and economic considerations. The Federal Water Pollution Control Act Amendments of 1972 have charged the United States Environmental Protection Agency with establishing effluent limitations from point sources of discharge into the navigable water of the United States. A detailed study, sponsored by EPA, of the water of ore processing plants took place in 1974 and 1975 and guidelines for these plants will presumably have been published by the time this paper has been presented(1). The action of many of the individual states preceded the EPA in this attempt to regulate the quality of the water discharged from industrial point sources. Even with recycle of tailings water, some water is discharged from tailings dams into the substrata and at least one state is currently preparing guidelines for the quality of water discharged into the substrata.

Jan 1, 1976

By F. V. Lenel, G. S. Ansell, J. A. Dromsky

The growth of aluminum oxide particles in a nickel matrix was studied eve?. the temperature vange of 2140° to 2470°F. The instability of the dispersed alumina was shown to be independent of the crystal structure of the alumina. The activation energy for the growth of the dispersed alumina was found to be 84.7 1 2.0 kcal. The particle radius increased as a function of time. These results indicate that the growth is not diffusion controlled. It is believed that the rate controlling mechanism is the dissolution of the aluminum and oxygen atoms into the nickel lattice. THE strength properties of alloys which consist of a finely dispersed second phase in a metallic matrix depend upon the spacing between the second phase particles. It is therefore desirable to achieve very fine dispersions in these alloys. Furthermore, to retain the properties these very fine dispersions must be stable during fabrication and service of the alloys. The best known of the dispersion strengthened materials, the SAP type alloys, which consist of a dispersion of aluminurn oxide in aluminum, have exceptionally good stability up to the melting point of aluminum. There is evidence, however, that other dispersion strengthened alloys, even those consisting of refractory oxides in a metal matrix, may be less stable. This investigation is concerned with the stability of Ni-Al2O3 alloys in the temperature range in which these alloys are usually fabricated. The mechanical properties of Ni-Al2O3 alloys at elevated temperatures have been previously investigated by Crelnens and rant,' and Gregory and Goetzel.2 The behavior of these alloys in stress rupture tests appears to indicate that at temperatures below 1800°F they are highly stable. There is some doubt, however, as to their stability at the higher temperatures used during the conventional fabrication. Cremens and Grant, in preparing their test alloys, cousolidated, by powder metallurgical techniques, nickel powders as fine as 0.13 µ diam and alumina powders as fine as 0.018 µ. Metallo- graphic examination of the alloys following fabrication revealed that none had interparticle spacings of less than 2 µ. Considering the size of the original component powder particles, it is likely that the dispersions coarsened during fabrication. Gregory and Goetzel, in their studies of extruded alloys of 80 pct Ni—-20 pct Cr matrixes with nonmetallic dispersion, observed a definite coarsening of the alumina dispersions in alloys sintered at 2280°F as cantrasted to those sintered at 2000oF. Similar observations on the spheroidization and growth of thoria particles finely dispersed in a nickel matrix were made by D. K. Worn and S. F. Marton.3 As a result of such coarsening, much of the effort expended in the preparation of very fine powder mixtures would be lost. The mechanical properties of the alloys which had experienced coarsening would be expected to be poorer than if the original dispersions had been retained. EXPERIMENTAL PROCEDURE Ni-Al2O3 alloys were produced from powder prepared by a coprecipitation technique. Aluminum hydroxide and nickel hydroxide were coprecipitated from chloride solutions of the metals. The mixed hydroxides were calcined to form metal oxides and the nickel oxide in the mixture was selectively reduced to nickel by treating it in hydrogen. Specimens were compacted from the resultant powder which consisted of a fine, uniform mixture of aluminum oxide and nickel particles. The compacts were sintered by resistance hot pressing4, a densification technique which requires exposure times of the order of only a second or less at elevated temperatures. A conventional sintering process was not used, since the temperature required for densification would have to be in the region in which the stability of the dispersion was to be studied. A series of hot pressed specimens were treated in hydrogen at temperatures from 2140o to 2470°F (1171o to 1355oC, for times up to 120 hr. Changes in the microstructures were studied by electron microscopy using the two-stage preshadowed carbon replica method.5 In performing a lineal analysis on a series of micrographs from each specimen it was found more convenient to determine the mean free path between alumina particles rather than particle radii as the parameter of growth. Although these quantities are directly proportional for only spherical particles, the alumina particles in these alloys

Jan 1, 1962

By Werner Langguth

The modern process and plant for the precipitation of gold from chlorine solutions, by sulphurous acid gas and hydrogen sulphide, differ materially from the older methods of precipitating with sulphate of iron. The chemical process and its applicability, as carried out in the Golden Reward chlorination-works at Deadwood, S. D., was described and discussed in the Engineering and Mining Journal, of New York, for February 14, and March 21, 1891. I purpose to give, in this paper, the details of construction from a general standpoint—the particular arrangement, most suitable to each case, depending, of course, upon local conditions. The accompanying sketch shows the arrangement. The plant consists of a wooden, lead-lined tank, in which the chlorine solution is precipitated; apparatus for the production of the precipitants, sulphurous acid and hydrogen sulphide; and a pressure-tank and filter-press for the collection and filtration of the precipitated gold-sulphides. These parts and arrangements are, in general, those which I employed in the Deadwood chlorinationworks, and which have proved practically successful, more than $100,000 worth of gold having been already precipitated by this method. In the construction of the generator and pressure-tank I have made, however, a few slight changes. 1. The Precipitating-Tank. The exact dimensions of this tank are not of much importance. A horizontal area of 10 x 12 feet and a height of 12 feet, holding about 7000 gallons of solution, is a good size. As the amount of attention and care required to precipitate the solution in a precipitatingtank is independent of the size of the vessel, there is economy in tanks of large capacity. Square tanks are more advantageous than round ones, because they need less floor-space, and at the same time are cheaper in construction. These tanks are made of common 2inch pine boards and 12 x 12-inch timber. They are well-bolted,

Jan 1, 1893

CONTENTS PAGE GEISMER, H. S.-Coal Washing Practice in Alabama. Discussed by William Kelly, H. S. Geismer, H. D. Pallister, L. E. Bryant, Milton H. Fies, Elmer F. Harris, James A. Barr, George G. Crawford, E. C. Wright, George S. Rice, R. V. Norris 1 MILLER, F. W.-Byproduct Coking in Alabama. Discussed by Theodore Swann 4 FIES, MILTON H.-Alabama Coal Mining Practice. Discussed by Milton 11. Fies, R. V. Norris, R. D. Hall, L. E. Bryant, George S. Rice, H. S. Geismer 5 MUSSEY, H. E.-Blast-furnace Practice in Alabama. Discussed by C. A. Meissner, Franklin H. Crockard, H. E. Mussey, W. H. Oldham 14 Coal Washing Practice in Alabama Discussion of paper of H. S. GEISMER, presented at the Birmingham Meeting, October 1924, and issued, as Paper No. 1363-C, with MINING AND METALLURGY, September, 1924. WILLIAM KELLY, Iron Mountain, Mich.-Is the dry-cleaning method used? H. S. GEISMER.-Neither the dry-cleaning process nor the Chance sand-liquid method has been tested in Alabama; but all other methods used for cleaning bituminous coal have been largely brought to perfection in this state. H. D. PALLISTER, Tuscaloosa, Ala.-Have you the results from the recent work on the tables with reference to fine coal? H. S. GEISMER.-None of the iron-producing companies has adopted the tables, though three commercial operators have installed tables within the last six months. I tried to learn the results, but they were not willing to release the data just now. At the mines producing domestic coal, fines present a difficult problem; until within the past six months all the fine coal was wasted. The operators are trying to recover some of it on the table. L. E. BRYANT, Rockwood, Tenn.-Is there any connection between the sulfur content of the sludge and the effect of the sludge on vegetation?

Jan 7, 1925

By J. W. Spretnak, V. Kandarpa

Stress -induced ordering of carbon atoms is studied in a series of Fe-Mn-C alloys. A prominent peak is found in the vicinity of 280°C at frequencies of the order of 1.0 cps, with an associated activation energy of 37 kcal per mole. The height of the peak is linearly rekzted to the concentration of carbon in solution. The distortion of octahedral holes by manganese atoms appears to be predominant over carbon-carbon pair interactions. RELAXATION by stress-induced ordering of point defects is expected whenever the introduction of these point defects produces distortions which have a lower symmetry than that of the lattice. Under zero stress, the isolated point defects occupy the crystallographic-ally equivalent positions in the lattice, as these represent states of equal energy. However, if the defect sites are asymmetric, application of an uniaxial stress will split the energy states, and a redistribution of the defects among various states will take place. This is the case of the internal friction peak called the Snoek peak,1 resulting from isolated interstitials in bcc metals. The interstitial sites in this case have tetragonal symmetry. In the case of fcc and hcp lattices, such an effect is not expected from isolated point defects because of the symmetrical nature of the interstitial sites. However, internal friction peaks arising from interstitial diffusion have been reported both in hcp2,3 and fcc4-8 lattices. These peaks are often explained on the basis of stress-induced ordering of interstitial solutes, caused by the deviation of interstitial sites from their cubic symmetry through the presence of nearby defects. In the case of fcc lattices, evidence for interactions of both the substitutional-interstitial4,6,13 and interstitial-interstitial types5'798'14 have been presented by various investigators. The purpose of the present investigation was to study the internal friction peak attributed to the diffusion of interstitial carbon atoms in high purity austenitic manganese steels and to account for the peak in the light of the existing models. MATERIALS The Fe-Mn-C alloys used in the present investigation were made in two different ways, designated as Type I and Type 11. Type I alloys were made from high purity Fe-Mn alloys obtained in the form of 0.04- in.-diam wires from Materials Research Corporation, Orangeburg, N.Y. These alloys were carburized to different levels using gas mixtures of H2 and CH4 at 1000°C. Type I1 alloys were made in this laboratory starting with zone refined iron, spectrographically pure manganese, and spectrographically pure carbon. They were melted in an argon arc melting furnace and drawn into 0.04-in.-diam wires. All the wires were annealed at about 900°C for 3 hr prior to the internal friction experiments. After the measurements of internal friction, the phases in the samples were identified by X-ray diffraction and the carbon determined by the combustion method. EXPERIMENTAL PROCEDURE In the present work, a classical Ke-type pendulum was used. The details of the equipment were described previously by D. T. Peters.9 Dry helium at 40 torr was used in all the experiments. The internal friction, measured as the logarithmic decrement of the torsion amplitude of vibration was determined as a function of temperature, from ambient to about 500°C. The background internal friction was assumed to have the form of the exponential of the inverse temperature and was subtracted from the raw data. The height of the peak was measured at the position of the maximum in the plot of the internal friction versus temperature. The activation energies of the peaks were measured by the peak shift method. The internal friction values for an alloy were obtained as a function of temperature at different frequencies of vibration. The position of the peak changes with frequency, the higher the frequency the higher the peak temperature. The activation energy of the process associated with the peak is obtained using the formula

Jan 1, 1970

By Irving Cadoff, Kurt Komarek, Edward Miller

Barium can be purified by equilibration with titanium. The melting point of barium was found to be 726.2° i 0.5 °C. The room-temperature lattice parameters of BaTe and Bask are 7.004 * 0.002A and 6.600 * 0.002A. Melting points for BaTe and Base were found to be 1510° * 30°C and 1830° ± 50°C, respectively. HIGH-purity barium and its compounds are difficult to prepare because of the reactivity of barium with the atmosphere and the large heats of formation of the compounds. Purification of barium by vacuum distillation,' and the preparation and properties of barium oxide2 and barium sulfide3 have been reported. However, little has been done on the homologous compounds barium selenide and telluride. PURIFICATION OF BARIUM Distilled barium obtained from King Laboratories was used as the starting material. The analysis supplied with the metal showed the presence of: 0.4 wt pct Sr, 0.001 pct Mg, 0.02 pct F, 0.003 pct Cu, 0.005 pct Na and less than 5 x 10-3 wt pct of any other metallic impurity. Analyses for oxygen and nitrogen were not available. Since there is evidence4 that any barium nitride present in the starting material may decompose on distillation producing nitrogen which can contaminate the distillate, further purification was performed. At elevated temperatures, any nitrogen and oxygen present in barium should be removed by reaction with titanium. Assuming that the solubility of oxygen in liquid barium is negligible near the melting point of barium, any oxygen present will be in the form of BaO. Removal of oxygen from molten barium is expressed by the equation: BaO(S)+ TixOy(S) = Ba(l)+ TixO(y+1)(s) where Ti,Oy and TixO(y+1) are solid solutions of oxygen in titanium. At 1000°C, the change in free energy for this reaction is negative for (y+1)/x +y+1) x (100) 17.5 at. pct O.5 Since reaction with commercially pure titanium (containing 0.07 wt pct oxygen) results in a free energy change for the reaction of -19 kcal per g-atom, slight solubility of oxygen in barium would not hinder the oxygen removal. Since comparable thermodynamic data are not available to permit calculation of the partition of nitrogen between liquid barium and titanium, a similar quantitative relationship cannot be obtained. However, on the basis of work by Kubaschewski and Dench,5 complete removal of nitrogen from liquid barium can be expected. Since the melting point of barium is depressed markedly by small additions of nitrogen,' the change in melting point during reaction of barium with titanium was used to follow the purification reaction. MELTING POINT OF BARIUM A 50-g sample of barium was sealed by arc welding under argon into an all titanium crucible provided with a thermocouple well. The melting point of the sample was determined by thermal analysis, using a Pt/Pt-10 pct Rh thermocouple which was calibrated according to National Bureau of Standards specification6. The crucible was then heated for 48 hr at 950°C in vacuum and the melting point redetermined. This procedure was repeated until three successive thermal analyses agreed within ±0.5oC, the limits of error of the analysis. The melting point increased from an initial value of 720.0°C to a final value of 726.2°C. Analysis on samples quenched from 950°C gave a solubility value of 0.004 wt. pct Ti. Assuming that the titanium-barium phase diagram is similar to those of titanium-magnesium7 and titanium-calcium,8 the solubility of titanium in liquid barium decreases with decreasing temperature. Therefore, the solubility of titanium in liquid barium should be less than 0.004 wt. pctat the melting point (726oC), and the effect of dissolved titanium on the melting point would be negligible. Addition of up to 3 wt pct Sr does not significantly change the melting point of barium,7 so that the effect of the 0.4 wt pct Sr in the starting material will also be negligible. The value of 726.2" ± 0.5C obtained for the melting point of barium can be compared .with a determination carried out by Keller and coworkers in low-carbon steel crucibles,' who obtained a value of 725± 1C, using barium purified by fractional distillation. The higher value obtained in the present investigation is indicative of the effectiveness of titanium in removing traces of nitrogen. PREPARATION OF BaTe AND Base The compounds were prepared by direct reaction

Jan 1, 1961

By Mitchell, Edmund I.

VARIOUS suggestions as to proper fees for engineering services have been put forth by individual practitioners and by the American Institute of Consulting Engineers, the Connecticut Society of Civil Engineers, the Iowa Engineering Society and the Mahoning Valley (Ohio) Engineers, for the guidance of both the engineer and his client. The American Institute of Architects also has a schedule of minimum charges (revised 1908). So far as can be determined, however, the four national societies representing civil, mining, mechanical and electrical engineering have never given consideration to this question. An examination of technical periodicals published during the past decade shows that these schedules make provision for three methods of charging; i.e., (A) a percentage of the cost of the completed project; (B) a per diem rate; and (C) a fixed sum. Suggested minimum charges are as follows:

Jan 1, 1921

By S. WHINERP

(Cleveland Meeting, October, 1912.) I AM indebted to L. E. Bryant, of Danville, Ky., President of the Virginia Mining Co., operating coal-mines in Scott county, Tenn., for the following information relating to the existence of the Clinton iron-ore under the NW. slope of the Cumberland Plateau in Kentucky and Tennessee. During the past 15 years quite an important oil-field has been developed in a region having Wayne county, Ky., as its center, and a large number of wells have been drilled in that and adjacent territory in the search for oil. Many of' these wells have been carried to considerable depths below the recognized oil-bearing horizon, and one of them was drilled by Mr. Bryant at Pine Knot, a station on the Cincinnati, New Orleans & Texas Pacific railroad, a few miles north of the point where that road crosses the Kentucky-Tennessee State-line. The elevation of the surface at the crossing is about 1,400 ft. above sea-level. The railroad is located on the dividing ridge between the Cumberland river and Big South Fork. At a depth of 1,720 ft. below the surface the drill reached and passed through a formation which the drillers called " red rock," but which Mr. Bryant classified as Clinton iron-ore, as its geological position corresponded to that formation. The ore at this point was 6 ft. thick and appeared to be of uniform quality throughout. An analysis of the drillings gave : Fe, 33; Mn, 0.25; Si02? 3 ; Al203, 2 ; CaO, 13; MgO, 7 ; P,05, 0.333 per cent. ; S, trace. This analysis seems to confirm the belief that the ore is Clinton, and that it is of a quality equal to the average of the deep or unbleached Clinton ores in Tennessee and Alabama. This discovery led Mr. Bryant to make further examinations and inquiries, and he found that the stratum called " red rock " by the drillers had been passed through and noted in the great majority of the wells carried down to the same geological hori-

Oct 1, 1912

By Alexander Field

IN THE light of the experimental data on equilibrium for the reaction C + FeO = Fe + CO in molten steel recently obtained by Kinzel and I Egan,1 it is necessary to revise current theories regarding the nature of equilibrium between carbon and FeO in the basic open-hearth furnace. According to the measurements of these investigators the equilibrium constant m for the above reaction for a pressure of dissolved CO equal to 1 atm. is equal to 0.0005 at 1550° C., when concentrations of carbon and. FeO are expressed in percentages by weight. Their work also shows that, with the pressure of CO fixed at 1 atm., not only is the product of carbon and FeO constant, but carbon and FeO are each independently constant-a circumstance which might have been predicted from theoretical considerations. At 1550° C., carbon is constant at about 0.025 per cent. and FeO at about 0.020 per cent., with the pressure of dissolved -CO equal to 1 atm., the product of these two constants being equal to the originally mentioned constant of 0.0005. Available data on the dissolved FeO content of samples taken from the metal bath at practical slag-metal equilibrium prove that this FeO content is determined solely by temperature and the effective FeO content of the slag. The distribution constant r at 1550° C., as determined by Herty, Gaines, Larsen, Simkins, Geruso and Watkins2 is equal to 0.0086. A slag would have to contain 0.020/0.0086 = 2.3 per cent. effective FeO or less in order to prevent the metal from containing more dissolved FeO than that required for equilibrium with CO at 1 atm. pressure. Such low percentages of FeO are never found in basic open-hearth slags at the completion of a heat when rate of carbon drop has become practi-

Jan 1, 1930

By Alexander L. Field

In the light of the experimental data on equilibrium for the reaction C + FeO = Fe + CO in molten steel recently obtained by Kinzel and Egan,l it is necessary to revise current theories regarding the nature of equilibrium between carbon and FeO in the basic open-hearth furnace. According to the measurements of these investigators the equilibrium constant m for the above reaction for a pressure of dissolved CO equal to 1 atm. is equal to 0.0005 at 1550" C., when concentrations of carbon and FeO are expressed in percentages by weight. Their work also shows that, with the pressure of CO fixed at 1 atm., not only is the product of carbon and FeO constant, but carbon and FeO are each independently constant—a circumstance which might have been predicted from theoretical considerations. At 1550" C., carbon is constant at about 0.025 per cent. and FeO at about 0.020 per cent., with the pressure of dissolved CO equal to 1 atm., the product of these two constants being equal to the originally mentioned constant of 0.0005. Available data on the dissolved FeO content of samples taken from the metal bath at practical slag-metal equilibrium prove that this FeO content is determined solely by temperature and the effective FeO content of the slag. The distribution constant r at 1550" C., as determined by Herty, Gaines, Larsen, Simkins, Geruso and Watkins2 is equal to 0.0086. A slag would have to contain 0.020 = 2.3 per cent. effective 0.0086 FeO or less in order to prevent the metal from containing more dissolved FeO than that required for equilibrium with CO at 1 atm. pressure. Such low percentages of FeO are never found in basic open-hearth slags at the completion of a heat when rate of carbon drop has become practi-

Jan 1, 1930

By F. Keller

SOME PHRASEMAKER has aptly said that nature made aluminum light but research made it strong. Research has been a vital element in the past progress of the aluminum industry and its future growth likewise depends upon the application of the results of research. The role of aluminum products in World War II is well known and this metal will certainly be increasingly important in the postwar world. Some of the principal developments in the war years were in the field of high-strength aluminum alloys. New and stronger alloys were developed which enabled designers to get increased speed and performance in our fighter planes and bombers. The aircraft industry will continue to use these new materials for peacetime passenger and cargo airplanes. High-strength alloys will also find structural applications in trucks, buses, trains, ships, and bridges.

Jan 1, 1946

By Arno C. Fieldner

METALLURGICAL coke and the by-products of the carbonization of coal continue in strong demand. Nearly 500 new by-product ovens were constructed in 1943. Output of by-product coke in the first ten months of the year was about 2 1/2 percent higher than in the corresponding period of 1942, but beehive production remained on approximately the same level as last year and constituted about 11 per cent of the total coke output.

Jan 1, 1944

By George W. Pawel

OWING largely to its value as a toughener and strengthener of steel for both industrial and military purposes, nickel is playing, an important role in the current war. It is fine of the metals in which the Allies enjoy a definite edge over the Axis nations and this time there is no place to which the Germans may send another submarine "Deutsehland" and expect to pick up a cargo of nickel to replenish their exhausted supplies. Total world nickel production thanks almost entirely to the expanded operation of the International Nickel Co. of Canada at Sudbury must now be at the rate of around 175,000 tons a year scarcely more than 5 per cent of which is accounted for by Germany, Italy and Japan. This represents more than four times the world output at the end of the first World War.

Jan 1, 1943

By F. R. Cattoir, R. W. Kimball, C. T. Anderson

ONE of the principal impurities in all steels is sulphur. Sulphur-bearing, manganese-free steels exhibit hot shortness. Manganese is added to steel to improve the hot-working properties. If no sulphur were present in steel, it is probable that hot shortness would be nonexistent. This paper is the first of a series to be issued by this Laboratory reporting the measurements of hot forgeability tests and the physical properties of Fe-C alloys to which additions of various alloying elements have been made. The present paper describes the results- obtained by the addition of varying amounts of sulphur to Fe-C alloys. To obtain control over residual elements in the various charges melted in the arc furnace, it was considered advantageous to use sponge iron from one source as the melting stock rather than scrap metal having an unknown history. Small amounts of unwanted alloying elements might be introduced into the charge when scrap was used, thereby influencing the results of the various heats. A sponge iron having a high silica-lime ratio was used. Ore from Sunrise, Wyo., had been reduced to sponge iron and briquetted at the Bureau of Mines sponge-iron plant at Laramie, Wyo. The briquettes were 5 in. in diam and 2 to 3 in. in thickness, and weighed about 10 lb each. The chemical analysis of the sponge iron is as follows: C, 0.67 pct; Mn, 0.10; SiO2, 4.75; CaO, 1.4; P, 0.044; S, 0.72; MgO, 0.4; A12O3, 1.1; total Fe, 87.5; Fe metallic, 79.2; and reduction, 90.5 pct. Where a reducing agent was required, crushed graphite electrodes usually were used. The charcoal available contained 0.20 pct S. An analysis of the available coke showed it to contain 0.70 pct S. Where high sulphur heats were required, elemental sulphur additions were made to the ladle. Limestone of good quality was obtained locally and had the following analysis: CaO, 53.7 pct; MgO, 0.8; ignition loss, 42.4; R2O3, 0.2; SiO2, 3.0; and P2O5, 0.014. Melting Procedure Sponge iron was melted to produce metal stock for the experimental alloys in a silica-lined, three-phase, direct-arc, size ST, Moore Rapid Lectromelt furnace with a 500 kva rating. Fig. 1 shows this furnace installation. About 25 tons of sponge iron was melted in 75 heats, averaging 927 lb of sponge iron to the heat. An addition of carbon was required to complete the reduction of a portion of the iron oxide remaining in the sponge to prevent high losses of iron oxide in the slag and a low carbon content in the resulting metal. As reducing agents in preparing the melting stock, charcoal, coke, and a carbon product resulting from the thermal decomposition of natural gas were used. The quantity varied from 20 to 60 Ib per furnace charge, with an average of 38 lb. An average analysis of the metal obtained gave 0.52 pct C, about 0.01 pct Mn, 0.070 pct P, and 0.092 pct S. The average yield of metal was 647 lb with 241 1b of slag, the sponge-iron recovery being 70 pct. The metal obtained in melting the sponge iron was cast into pigs weighing about 20 lb each to facilitate recharging into the furnace for further refining. The pouring of the pigs is shown in Fig. 2. The average power consumption for the production of the 24 tons of metal obtained was 1704 kw-hr per ton.

Jan 1, 1954

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting). A few mimeographed copies of this provisional report were made. Dr. W. P. Haynes presented some notes prepared by Dr. F. H. Lahee, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Com- mittee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. Sherwin F. Kelly pointed out that much time in university training, which ought to be devoted to technical subjects, was taken .up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. Thom protested against the crowding of high-school material into already overcrowded college curricula. C. E. Dobbin, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1946

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting). A few mimeographed copies of this provisional report were made. Dr. W. P. Haynes presented some notes prepared by Dr. F. H. Lahee, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Com- mittee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. Sherwin F. Kelly pointed out that much time in university training, which ought to be devoted to technical subjects, was taken .up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. Thom protested against the crowding of high-school material into already overcrowded college curricula. C. E. Dobbin, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1946

By Oliver Bowles

TO keep pace with technical progress is an important function of any industry. All branches of mining may learn important lessons by observing progress made in other branches. The non-metallic mineral industries may learn much from each other as well as from the metal miner and the metallurgist. Recent technical advances which have come to the attention of the Committee on Non-metallic Minerals are presented herewith for consideration and comment. It is planned to present this review for open discussion at the February, 1931, meeting of the Institute. Comments will be welcomed either in the form of written or oral discussion. It is desired that new developments not covered in this paper be brought up at that time. Some notable advances have been made in cement technology. Recognition is now being given to the advantages of closed-circuit grinding of cement raw materials in wet-process plants, with stage removal of the fine materials, It increases mill capacity, reduces the wear of grinding media, and also reduces the power requirement. The method is well known in metallurgical plants, and its acceptance by cement companies is another illustration of the lessons the non-metallic industries may learn from the metal industries. Closed-circuit dry grinding has also proved advantageous for both raw materials and clinker.

Jan 1, 1931

By Y. A. Rocher, J. E. Dorn, L. A. Shepard

Creep activation energies for single aluminum crystals favorably oriented for shear by (010) [101] glide were detemined over the temperature range from 78" to 900°K. Observations of slip bands on the specimen surface were made in conjunction with the investigation. From 78" to 780°K, the activation energies obtained in this imestigation agreed closely with those previously found for creep by (111) [101] slip. Between 78" and 140°K, the activation energy was identified with the Peierls process, while between 260°and 780°K the activation energy was close to that for cross-slip. The coarse wavy slip bands nominally parallel to the (010) plane observed above 260°K were attributed to fine cross-slip. From 800" to 900°K, unusually high apparent activation energies ranging from 28,000 to 54,000 cal per mole were obtained. These apparent activation energies were attributed to re crystallization. AS illustrated in Fig. 1, a recent investigation1 has shown that creep of aluminum single crystals by the (111) [i01] mechanism is controlled by three unique processes, each of which is characterized by a single activation energy which is independent of the applied stress and the creep strain. A comparison of the observed activation energies with theoretically calculated values permits a fairly clear identification of the three operative creep processes. Below 450°K, where the activation energy for creep is 3,400 cal per mole, the deformation is controlled by the Peierls process, the activation energy for creep agreeing well with that calculated by seeger2 for the energy required to nucleate the motion of a dislocation loop against the atomic forces of the lattice. Between 590° and 750°K, the observed activation energy for creep of about 28,000 cal per mole agrees well with the energy necessary to induce cross-slip. Seeger and schoeck3 estimate that the activation energy is about 24,000 cal per mole whereas Friedel4 recently calculated this activation energy to be 28,000 cal per mole. Above 800°K the activation energy of 35,500 cal per mole that was observed for creep agrees well with that estimated for self-diffusion in aluminum.= In this range the operative rate-controlling slip process has been clearly identified as that arising from the climb of edge dislocations. The objective of this investigation is to ascertain whether a single crystal of aluminum favorably oriented for simple shear in the [loll direction on the (010) plane might exhibit uniquely different activation energies for creep from those obtained previously for (111) [101] slip. Whereas the exis- tence of such unique activation energies would constitute incontrover table evidence for new mechanisms of slip, the absence of any new activation energies might suggest that slip of aluminum is confined to the (111) [loll mechanism. Several factors prompted the selection of the (010) [101] orientation for study. First, there are more reported observations of (010) [loll slip than of any other nonoctahe-dral mechanism.8-10Secondly, Chalmers and Martius1l have concluded from considerations of the energies of dislocations that (010) slip is the second most favored mechanism in face-centered-cubic metals. Finally, favorable orientations for simple shear by the (010) [loll mechanism provide the least favored orientation for slip by the (111) [101] mechanism. EXPE-RIMENTAL PRO-CEDURE The high-purity aluminum stock, specimen preparation, shear fixture, extensometry, and experimental technique used in this investigation were the same as those previously reported.' Single-crystal spheres grown from the melt of 99.995 pct pure Al* were _ *The high-purity aluminum used in this investigation was graciously given by the Aluminum Company of America. oriented, carefully machined into dumbbell-shaped shear specimens, annealed, and chemically polished. The finished specimen had a central reduced section 0.190 in. wide and 0.590 in. in diam and 1/4-in. grip sections at both sides, 0.690 in. in diameter. The specimen was oriented in the stainless steel grips of the shear fixture with the (010) plane perpendicular to the dumbbell axis and the [loll direction parallel to the stress axis within 2 deg. Creep activation energies were calculated in the previously described manner1 from determinations of the instantaneous change in shear strain rate produced by an abrupt 15 to 20 deg increase or decrease in test temperature. If is the instantaneous strain rate at strain y and temperature T1, and ?2 the instantaneous rate at y and T2,

Jan 1, 1960

By G. L. Wilhelm

Prior to the construction of a 450 tpd concentrator at the Mayflower mine, owned by the New Park Mining Co. and operated by the Hecla Mining Co., the common mining methods were cut and fill, with waste or gob filling and square set timbering with waste fill. Stoping operations were beset with the usual problems related to waste filling methods- storage and handling of fill material from development, costly waste excavations necessary to obtain a portion of the needed waste rock, slow mining cycles due to filling and inefficient ground support. After Hecla Mining Co.'s successful utilization of sandfill in its mines in the Coeur d'Alene district, utilization of hydraulic fill in stoping operations at the Mayflower was a logical development of the modernization plan then in progress. The mine, located in the southeasterly part of the Park City mining district, Utah, is a medium size producer of lead and zinc ores, with gold, silver and copper as secondary minerals. The mine has been producing commercial ore since 1939 from a dual vein system which outcrops at an elevation of 7200 ft in the Wasatch Range. Access to the present mining areas is gained by a 7200-ft haulage tunnel and by an interior, three-compartment main shaft. The present mining horizons are about 2400 ft deep. The average horizontal cut and fill stopes, ranging from 3-15 ft wide and up to 120 ft long, can be classed as small.

Jan 5, 1968